ARM: dts: Correct the base address of pinctrl_3 on Exynos5250
Subsystems (2)
PATCH RESEND v2 1/1 ARM: dts: Correct the base address of pinctrl_3 on Exynos5250
This patch corrects the base address of pinctrl_3 on Exynos5250 platform.
---
Changes since V1:
- Added platform name in the subject line.
arch/arm/boot/dts/exynos5250-pinctrl.dtsi | 2 +- arch/arm/boot/dts/exynos5250.dtsi | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/exynos5250-pinctrl.dtsi +1 -1
@@ -763,7 +763,7 @@ }; }; - pinctrl@03680000 { + pinctrl@03860000 { gpz: gpz { gpio-controller; #gpio-cells = <2>;
arch/arm/boot/dts/exynos5250.dtsi +2 -2
@@ -169,9 +169,9 @@ interrupts = <0 50 0>; }; - pinctrl_3: pinctrl@03680000 { + pinctrl_3: pinctrl@03860000 { compatible = "samsung,exynos5250-pinctrl"; - reg = <0x0368000 0x1000>; + reg = <0x03860000 0x1000>; interrupts = <0 47 0>; };
Signature · 1 line
1.7.4.4
A message that is not in the archive (sent off-list or not yet received): 1371025425-480-1-git-send-email-padma.v-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org
PATCH RESEND v2 1/1 ARM: dts: wm8994: Add wm8994 regulator support on smdk5250.
This patch adds the required regulator supplies and properties for wm8994 codec on smdk5250 board.
---
Changes since V1:
- Clubbed the same supply regulators as suggested by Mark.
arch/arm/boot/dts/exynos5250-smdk5250.dts | 37 +++++++++++++++++++++++++++- 1 files changed, 35 insertions(+), 2 deletions(-)
arch/arm/boot/dts/exynos5250-smdk5250.dts +35 -2
@@ -37,6 +37,30 @@ }; }; + vdd:fixed-regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vdd-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + dbvdd:fixed-regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "dbvdd-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + spkvdd:fixed-regulator@2 { + compatible = "regulator-fixed"; + regulator-name = "spkvdd-supply"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + i2c@12C70000 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <20000>;
@@ -47,8 +71,17 @@ }; wm8994: wm8994@1a { - compatible = "wlf,wm8994"; - reg = <0x1a>; + compatible = "wlf,wm8994"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + + AVDD2-supply = <&vdd>; + CPVDD-supply = <&vdd>; + DBVDD-supply = <&dbvdd>; + SPKVDD1-supply = <&spkvdd>; + SPKVDD2-supply = <&spkvdd>; }; };
Signature · 1 line
1.7.4.4
Kukjin Kim
AppliedRE: [PATCH RESEND V2] ARM: dts: wm8994: Add wm8994 regulator support on smdk5250.
Quoted 10 lines · Padmavathi Venna
This patch adds the required regulator supplies and properties for wm8994 codec on smdk5250 board.
Signed-off-by Padmavathi Venna <[email protected]>---
Changes since V1:
- Clubbed the same supply regulators as suggested by Mark.
Applied, thanks.
- Kukjin
Kukjin Kim
AppliedQuoted 45 lines · Padmavathi Venna
This patch corrects the base address of
pinctrl_3on Exynos5250 platform.Signed-off-by Padmavathi Venna <[email protected]>---
Changes since V1:
- Added platform name in the subject line.arch/arm/boot/dts/exynos5250-pinctrl.dtsi | 2 +- arch/arm/boot/dts/exynos5250.dtsi | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-)arch/arm/boot/dts/exynos5250-pinctrl.dtsi +1
-1@@ -763,7 +763,7 @@ }; }; - pinctrl@03680000 { + pinctrl@03860000 { gpz: gpz { gpio-controller; #gpio-cells = <2>;arch/arm/boot/dts/exynos5250.dtsi +2
-3@@ -169,9 +169,9 @@ interrupts = <0 50 0>; }; - pinctrl_3: pinctrl@03680000 { + pinctrl_3: pinctrl@03860000 { compatible = "samsung,exynos5250-pinctrl"; - reg = <0x0368000 0x1000>; + reg = <0x03860000 0x1000>; interrupts = <0 47 0>; }; --
Quoted 1 line
1.7.4.4
Yes, right.
Thanks, applied.
- Kukjin
Quoted 5 lines · Padmavathi Venna
This patch corrects the base address of
pinctrl_3on Exynos5250 platform.Signed-off-by Padmavathi Venna <[email protected]>
(+ Olof)
Olof, there is no other fixes in my tree for v3.10 yet, so would be helpful if you could take this into fixes in arm-soc for v3.10. Just note, the wrong address added during v3.10 merge window.
If you want,
If any problems, please kindly let me know.
Thanks,
- Kukjin
Quoted 41 lines
---
Changes since V1:
- Added platform name in the subject line.arch/arm/boot/dts/exynos5250-pinctrl.dtsi | 2 +- arch/arm/boot/dts/exynos5250.dtsi | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-)arch/arm/boot/dts/exynos5250-pinctrl.dtsi +1
-1@@ -763,7 +763,7 @@ }; }; - pinctrl@03680000 { + pinctrl@03860000 { gpz: gpz { gpio-controller; #gpio-cells = <2>;arch/arm/boot/dts/exynos5250.dtsi +2
-3@@ -169,9 +169,9 @@ interrupts = <0 50 0>; }; - pinctrl_3: pinctrl@03680000 { + pinctrl_3: pinctrl@03860000 { compatible = "samsung,exynos5250-pinctrl"; - reg = <0x0368000 0x1000>; + reg = <0x03860000 0x1000>; interrupts = <0 47 0>; }; --1.7.4.4
Quoted 5 lines · Kukjin Kim
Quoted 4 lines · Padmavathi Venna
This patch corrects the base address of
pinctrl_3on Exynos5250 platform.
Quoted 7 lines
Quoted 1 line
Signed-off-by Padmavathi Venna <[email protected]>(+ Olof)
Olof, there is no other fixes in my tree for v3.10 yet, so would be helpful if you could take this into fixes in arm-soc for v3.10. Just note, the wrong address added during v3.10 merge window.
Huh. I guess we lucked out on snow since we're definitely using this and didn't hit any problems from it.
I'll apply to fixes.
-Olof