Fix broken bananapi m2 devicetree/regulators
Subsystems (2)
cover Fix broken bananapi m2 devicetree/regulators
This patchseries fixes the bananapi m1 devicetree, to be able to boot again. The first two patches update/improve the devicetree and the last patch adds all missing regulators.
Regards,
Philipp
Philipp Rossak (3):
arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes
arm: dts: sun6i: a31s: bpi-m2: improve pmic properties
arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 70 +++++++++++++++++++++++- 1 file changed, 67 insertions(+), 3 deletions(-)
Signature · 1 line
2.11.0
PATCH 1/3 arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes
This patch updates the vmmc-supply properties on the mmc0 and mmc2 node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we don't need it anymore.
--- arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +2 -3
@@ -42,7 +42,6 @@ /dts-v1/; #include "sun6i-a31s.dtsi" -#include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> / {
@@ -118,7 +117,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */ cd-inverted;
@@ -132,7 +131,7 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins_a>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; mmc-pwrseq = <&mmc2_pwrseq>; bus-width = <4>; non-removable;
Signature · 1 line
2.11.0
Re: [PATCH 1/3] arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes
Am Freitag, den 09.02.2018, 18:52 +0100 schrieb Philipp Rossak:
Quoted 33 lines
This patch updates the vmmc-supply properties on the mmc0 and mmc2 node to use the allready existent regulators.
We can now remove thesunxi-common-regulators.dtsiinclude since we don't need it anymore.Signed-off-by Philipp Rossak <[email protected]>---
?arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 5 ++--- ?1 file changed, 2 insertions(+), 3 deletions(-)arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +0
-0@@ -42,7 +42,6 @@?
?/dts-v1/;
?#include "sun6i-a31s.dtsi"
-#include "sunxi-common-regulators.dtsi"
?#include <dt-bindings/gpio/gpio.h>
?
?/ {arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +1
-1@@ -118,7 +117,7 @@ ?&mmc0 { ? pinctrl-names = "default"; ? pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; ? bus-width = <4>;? cd-gpios = <&pio 0 4
GPIO_ACTIVE_HIGH>; /* PA4 */
? cd-inverted;
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts line 134
Quoted 5 lines
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +1
-1@@ -132,7 +131,7 @@ ?&mmc2 { ? pinctrl-names = "default"; ? pinctrl-0 = <&mmc2_pins_a>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>;
^^ this here is wrong! this should be ®_aldo1
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts line 137
Quoted 3 lines
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +0
-0? mmc-pwrseq = <&mmc2_pwrseq>; ? bus-width = <4>; ? non-removable;
Philipp
PATCH 2/3 arm: dts: sun6i: a31s: bpi-m2: improve pmic properties
In reply to Philipp RossakThe eldoin is supplied from the dcdc1 regulator. The N_VBUSEN pin is connected to an external power regulator (SY6280AAC). With this commit we update the pmic binding properties to support those features.
--- arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +2 -0
@@ -162,6 +162,8 @@ reg = <0x68>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; };
Signature · 1 line
2.11.0
PATCH 3/3 arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators
In reply to Philipp RossakThis patch fixes a bootproblem with the Bananapi M2 board. Since there are some regulators missing we add them right now. Those values come from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi * reg_aldo2: 2,5V, powers the IO of the RTL8211E * reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E * reg_dldo2: 2,8V, powers the analog part of the csi * reg_dldo3: 3,3V, powers misc * reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
--- arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 56 ++++++++++++++++++++++++ 1 file changed, 56 insertions(+)
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +56 -0
@@ -99,6 +99,7 @@ pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_bpi_m2>; phy = <&phy1>; phy-mode = "rgmii"; + phy-supply = <®_dldo1>; snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */ snps,reset-active-low; snps,reset-delays-us = <0 10000 30000>;
@@ -193,7 +194,28 @@ #include "axp22x.dtsi" +®_aldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-gmac"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + ®_dc5ldo { + regulator-always-on; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1320000>; regulator-name = "vdd-cpus";
@@ -233,6 +255,40 @@ regulator-name = "vcc-dram"; }; +®_dldo1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-mac"; +}; + +®_dldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pb"; +}; + +®_eldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vdd-csi"; + status = "okay"; +}; + +®_ldo_io1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pm-cpus"; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>;
Signature · 1 line
2.11.0
Quoted 7 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to boot again. The first two patches update/improve the devicetree and the last patch adds all missing regulators.
Regards,
Philipp
Quoted 8 lines
Philipp Rossak (3):
arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes
arm: dts: sun6i: a31s: bpi-m2: improve pmic properties
arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulatorsarch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 70 +++++++++++++++++++++++- 1 file changed, 67 insertions(+), 3 deletions(-)
patches are not working
Thanks
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do with those patches. I tested them with the v4.15.0 Kernel since this is the last stable release and we are right now in the merging window.
I tested the latest mainline, without those patches and the kernel is not booting (I can't see any uart output).
Thanks,
Philipp
Quoted 23 lines · Sergey Suloev
Quoted 9 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to boot again.
The first two patches update/improve the devicetree and the last patch adds
all missing regulators.Regards,
PhilippQuoted 9 lines
Philipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators?
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts| 70
+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)patches are not working
Thanks
Quoted 6 lines · Philipp Rossak
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do with those patches. I tested them with the v4.15.0 Kernel since this is the last stable release and we are right now in the merging window.
Quoted 30 lines
I tested the latest mainline, without those patches and the kernel is not booting (I can't see any uart output).
Thanks,
PhilippQuoted 23 lines · Sergey Suloev
Quoted 9 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to boot again.
The first two patches update/improve the devicetree and the last patch adds
all missing regulators.Regards,
PhilippQuoted 9 lines
Philipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators?
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts| 70
+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Quoted 33 lines · Sergey Suloev
Quoted 32 lines · Philipp Rossak
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do with those patches. I tested them with the v4.15.0 Kernel since this is the last stable release and we are right now in the merging window.
I tested the latest mainline, without those patches and the kernel is not booting (I can't see any uart output).
Thanks,
PhilippQuoted 19 lines · Sergey Suloev
Quoted 18 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to boot again.
The first two patches update/improve the devicetree and the last patch adds
all missing regulators.Regards,
PhilippPhilipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators?
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts| 70
+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)
Quoted 7 lines
Quoted 4 lines
Quoted 4 lines
patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Can you please share a bootlog? Here is mine [1]. As you can see I'm able to boot.
I build it with this branch [2]. For testing you should replace the dtb and the uImage/zImage
Philipp
[1]: https://pastebin.com/mVjv3LDf
[2]: https://github.com/embed-3d/linux/tree/testing/bpi-m2-regulator-test-2
Quoted 48 lines · Philipp Rossak
Quoted 33 lines · Sergey Suloev
Quoted 32 lines · Philipp Rossak
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do with those patches. I tested them with the v4.15.0 Kernel since this is the last stable release and we are right now in the merging window.
I tested the latest mainline, without those patches and the kernel is not booting (I can't see any uart output).
Thanks,
PhilippQuoted 19 lines · Sergey Suloev
Quoted 18 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to boot again.
The first two patches update/improve the devicetree and the last patch adds
all missing regulators.Regards,
PhilippPhilipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators?
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts| 70
+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)Quoted 7 lines
Quoted 4 lines
Quoted 4 lines
patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Can you please share a bootlog? Here is mine [1]. As you can see I'm able to boot.
I build it with this branch [2]. For testing you should replace the dtb and the uImage/zImage
Quoted 6 lines
Philipp
[1]: https://pastebin.com/mVjv3LDf
[2]:
https://github.com/embed-3d/linux/tree/testing/bpi-m2-regulator-test-2
I am going to test it and come back with outcome
Thanks
Quoted 48 lines · Philipp Rossak
Quoted 33 lines · Sergey Suloev
Quoted 32 lines · Philipp Rossak
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do with those patches. I tested them with the v4.15.0 Kernel since this is the last stable release and we are right now in the merging window.
I tested the latest mainline, without those patches and the kernel is not booting (I can't see any uart output).
Thanks,
PhilippQuoted 19 lines · Sergey Suloev
Quoted 18 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to boot again.
The first two patches update/improve the devicetree and the last patch adds
all missing regulators.Regards,
PhilippPhilipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators?
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts| 70
+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)Quoted 7 lines
Quoted 4 lines
Quoted 4 lines
patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Can you please share a bootlog? Here is mine [1]. As you can see I'm able to boot.
I build it with this branch [2]. For testing you should replace the dtb and the uImage/zImage
Quoted 6 lines
Philipp
[1]: https://pastebin.com/mVjv3LDf
[2]:
https://github.com/embed-3d/linux/tree/testing/bpi-m2-regulator-test-2
My dmesg is very similar to yours unless it hangs on the last line [1]. For this test I used kernel from tag v4.15 with no additional patching.
Am Sonntag, den 11.02.2018, 10:55 +0300 schrieb Sergey Suloev:
Quoted 70 lines · Philipp Rossak
Quoted 61 lines · Sergey Suloev
Quoted 41 lines · Philipp Rossak
Quoted 40 lines
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do?
with those patches. I tested them with the v4.15.0 Kernel since this?
is the last stable release and we are right now in the merging window.I tested the latest mainline, without those patches and the kernel?
is not booting (I can't see any uart output).Thanks,
PhilippQuoted 23 lines · Sergey Suloev
Quoted 21 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to?
boot again.
The first two patches update/improve the devicetree and the last?
patch adds
all missing regulators.Regards,
PhilippPhilipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators?
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts| 70?
+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)Quoted 9 lines
Quoted 4 lines
Quoted 4 lines
patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Can you please share a bootlog? Here is mine [1]. As you can see I'm?
able to boot.
I build it with this branch [2]. For testing you should replace the?
dtb and the uImage/zImageQuoted 7 lines
Philipp
[1]: https://pastebin.com/mVjv3LDf
[2]:?
https://github.com/embed-3d/linux/tree/testing/bpi-m2-regulator-tes
t-2
Quoted 8 lines
My dmesg is very similar to yours unless it hangs on the last line [1].?
For this test I used kernel from tag v4.15 with no additional patching.
For me it looks like you have a different kernel and also an different dtb that you patch! And you are applying also a fixup script. These patches should be applied on top of linux mainline.
fixup script:
Applying kernel provided DT fixup script (sun6i-a31s-fixup.scr)
Linux versions:
4.15.0-00003-g1bbe5edde691 vs 4.15.0-sunxi-dirty
In addition to that you are also booting into fb/hdmi.
If you use my branch (uImage and dtb) and replace the current boot.cmd with this (to get the boot.scr you need to use mkimage) it should work:
setenv bootargs console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait panic=10
load mmc 0:1 0x43000000 ${fdtfile} || load mmc 0:1 0x43000000 boot/${fdtfile}
load mmc 0:1 0x42000000 uImage || load mmc 0:1 0x42000000 boot/uImage bootm 0x42000000 - 0x43000000
Quoted 90 lines · Philipp Rossak
Am Sonntag, den 11.02.2018, 10:55 +0300 schrieb Sergey Suloev:
Quoted 65 lines · Philipp Rossak
Quoted 57 lines · Sergey Suloev
Quoted 40 lines · Philipp Rossak
Quoted 39 lines
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do
with those patches. I tested them with the v4.15.0 Kernel since this
is the last stable release and we are right now in the merging window.I tested the latest mainline, without those patches and the kernel
is not booting (I can't see any uart output).Thanks,
PhilippQuoted 22 lines · Sergey Suloev
Quoted 21 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to
boot again.
The first two patches update/improve the devicetree and the last
patch adds
all missing regulators.Regards,
PhilippPhilipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing
regulators? arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 70+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)Quoted 8 lines
Quoted 4 lines
Quoted 4 lines
patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Can you please share a bootlog? Here is mine [1]. As you can see I'm
able to boot.
I build it with this branch [2]. For testing you should replace the
dtb and the uImage/zImageQuoted 7 lines
Philipp
[1]: https://pastebin.com/mVjv3LDf
[2]:
https://github.com/embed-3d/linux/tree/testing/bpi-m2-regulator-tes
t-2Quoted 8 lines
My dmesg is very similar to yours unless it hangs on the last line [1].
For this test I used kernel from tag v4.15 with no additional patching.For me it looks like you have a different kernel and also an different dtb that you patch! And you are applying also a fixup script. These patches should be applied on top of linux mainline.
fixup script:
Applying kernel provided DT fixup script (sun6i-a31s-fixup.scr)Linux versions:
4.15.0-00003-g1bbe5edde691 vs 4.15.0-sunxi-dirtyIn addition to that you are also booting into fb/hdmi.
If you use my branch (uImage and dtb) and replace the current boot.cmd with this (to get the boot.scr you need to use mkimage) it should work:
Quoted 7 lines
setenv bootargs console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait panic=10
load mmc 0:10x43000000${fdtfile} || load mmc 0:10x43000000boot/${fdtfile}
load mmc 0:10x42000000uImage || load mmc 0:10x42000000boot/uImage bootm0x42000000-0x43000000
the script is doing nothing, it is empty. The problem is related to hdmi.
The following dts code makes it happen:
&hdmi {
??????? status = "okay";
};
Quoted 90 lines · Philipp Rossak
Am Sonntag, den 11.02.2018, 10:55 +0300 schrieb Sergey Suloev:
Quoted 65 lines · Philipp Rossak
Quoted 57 lines · Sergey Suloev
Quoted 40 lines · Philipp Rossak
Quoted 39 lines
Hey Sergey,
Thanks for mentioning, but I think the problem has nothing to do
with those patches. I tested them with the v4.15.0 Kernel since this
is the last stable release and we are right now in the merging window.I tested the latest mainline, without those patches and the kernel
is not booting (I can't see any uart output).Thanks,
PhilippQuoted 22 lines · Sergey Suloev
Quoted 21 lines · Philipp Rossak
This patchseries fixes the bananapi m1 devicetree, to be able to
boot again.
The first two patches update/improve the devicetree and the last
patch adds
all missing regulators.Regards,
PhilippPhilipp Rossak (3):
?? arm: dts: sun6i: a31s: bpi-m2: update mmc supply nodes ?? arm: dts: sun6i: a31s: bpi-m2: improve pmic properties ?? arm: dts: sun6i: a31s: fix: bpi-m2: add missing
regulators? arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 70+++++++++++++++++++++++-
? 1 file changed, 67 insertions(+), 3 deletions(-)Quoted 8 lines
Quoted 4 lines
Quoted 4 lines
patches are not working
Thanks
same problem, but after applying the patches my device is till hanging.
Can you please share a bootlog? Here is mine [1]. As you can see I'm
able to boot.
I build it with this branch [2]. For testing you should replace the
dtb and the uImage/zImageQuoted 7 lines
Philipp
[1]: https://pastebin.com/mVjv3LDf
[2]:
https://github.com/embed-3d/linux/tree/testing/bpi-m2-regulator-tes
t-2Quoted 8 lines
My dmesg is very similar to yours unless it hangs on the last line [1].
For this test I used kernel from tag v4.15 with no additional patching.For me it looks like you have a different kernel and also an different dtb that you patch! And you are applying also a fixup script. These patches should be applied on top of linux mainline.
fixup script:
Applying kernel provided DT fixup script (sun6i-a31s-fixup.scr)Linux versions:
4.15.0-00003-g1bbe5edde691 vs 4.15.0-sunxi-dirtyIn addition to that you are also booting into fb/hdmi.
If you use my branch (uImage and dtb) and replace the current boot.cmd with this (to get the boot.scr you need to use mkimage) it should work:
Quoted 7 lines
setenv bootargs console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait panic=10
load mmc 0:10x43000000${fdtfile} || load mmc 0:10x43000000boot/${fdtfile}
load mmc 0:10x42000000uImage || load mmc 0:10x42000000boot/uImage bootm0x42000000-0x43000000
ok, I confirm that your patches are not related to the issue. It is the problem with sun4i drm / hdmi which is not working on bpi m2.
Thanks