ARM: dts: rockchip: phycore: Remove 1.8 GHz operation point
Subsystems (2)
PATCH 1/3 ARM: dts: rockchip: phycore: Remove 1.8 GHz operation point
Rockchip recommends to run the CPU cores only with operations points of 1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default values instead.
--- arch/arm/boot/dts/rk3288-phycore-som.dtsi | 20 -------------------- 1 file changed, 20 deletions(-)
arch/arm/boot/dts/rk3288-phycore-som.dtsi +0 -20
@@ -110,26 +110,6 @@ }; }; -&cpu0 { - cpu0-supply = <&vdd_cpu>; - operating-points = < - /* KHz uV */ - 1800000 1400000 - 1608000 1350000 - 1512000 1300000 - 1416000 1200000 - 1200000 1100000 - 1008000 1050000 - 816000 1000000 - 696000 950000 - 600000 900000 - 408000 900000 - 312000 900000 - 216000 900000 - 126000 900000 - >; -}; - &emmc { status = "okay"; bus-width = <8>;
Signature · 1 line
2.7.4
PATCH 2/3 ARM: dts: rockchip: phycore: Fix supply node for card's power
From: Wadim Egorov <[email protected]>
The card is powered by the RK818 switch vdd_sd which is supplied by VCC9 (VDD_3V3_IO).
--- arch/arm/boot/dts/rk3288-phycore-rdk.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/rk3288-phycore-rdk.dts +1 -1
@@ -265,7 +265,7 @@ disable-wp; pinctrl-names = "default"; pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; - vmmc-supply = <&vdd_io_sd>; + vmmc-supply = <&vdd_sd>; vqmmc-supply = <&vdd_io_sd>; status = "okay"; };
Signature · 1 line
2.7.4
PATCH 3/3 ARM: dts: rockchip: phycore: Support UHS mode for SD card on phyCORE-RK3288 RDK
In reply to Daniel SchultzFrom: Wadim Egorov <[email protected]>
The phyCORE-RK3288 RDK could enable SD3.0 card but need vdd_io_sd to support the voltage range from 1.8V to 3.3V.
And we have also to add relevant UHS modes to the sdmmc node. Let's also turn off the vdd_io_sd regulator in suspend state.
--- arch/arm/boot/dts/rk3288-phycore-rdk.dts | 4 ++++ arch/arm/boot/dts/rk3288-phycore-som.dtsi | 5 ++--- 2 files changed, 6 insertions(+), 3 deletions(-)
arch/arm/boot/dts/rk3288-phycore-rdk.dts +4 -0
@@ -265,6 +265,10 @@ disable-wp; pinctrl-names = "default"; pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; vmmc-supply = <&vdd_sd>; vqmmc-supply = <&vdd_io_sd>; status = "okay";
arch/arm/boot/dts/rk3288-phycore-som.dtsi +2 -3
@@ -336,11 +336,10 @@ regulator-name = "vdd_io_sd"; regulator-always-on; regulator-boot-on; - regulator-min-microvolt = <3300000>; + regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-state-mem { - regulator-on-in-suspend; - regulator-suspend-microvolt = <3300000>; + regulator-off-in-suspend; }; }; };
Signature · 1 line
2.7.4
Heiko Stübner
maintainerAm Dienstag, 13. Februar 2018, 10:44:32 CET schrieb Daniel Schultz:
Quoted 7 lines
Rockchip recommends to run the CPU cores only with operations points of 1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default values instead.
Signed-off-by Daniel Schultz <[email protected]>
applied all 3 for 4.17
Thanks
Heiko
Quoted 10 lines · Heiko Stübner
Am Dienstag, 13. Februar 2018, 10:44:32 CET schrieb Daniel Schultz:
Quoted 7 lines
Rockchip recommends to run the CPU cores only with operations points of 1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default values instead.
Signed-off-by Daniel Schultz <[email protected]>applied all 3 for 4.17
Thanks! I think I should have mentioned this earlier, but can you please add
ARM: dts: rockchip: phycore: Remove 1.8 GHz operation point to the stable tree v4.14?
Signature · 3 lines
Mit freundlichen Grüßen, With best regards, Daniel Schultz
Heiko Stübner
maintainerHi Daniel,
Am Mittwoch, 14. Februar 2018, 16:32:44 CET schrieb Daniel Schultz:
Quoted 8 lines · Heiko St?bner
Quoted 7 lines
Am Dienstag, 13. Februar 2018, 10:44:32 CET schrieb Daniel Schultz:
Quoted 6 lines
Rockchip recommends to run the CPU cores only with operations points of 1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default values instead.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Signed-off-by Daniel Schultz <[email protected]>applied all 3 for 4.17
Thanks! I think I should have mentioned this earlier, but can you please add
ARM: dts: rockchip: phycore: Remove 1.8 GHz operation point
to the stable tree v4.14?
I've moved that patch to the fixes branch and added the necessary Fixes and cc-stable tags, so it should eventually reach stable kernels as well.
Heiko