Skip to contentSkip to conversation

drm/panel: Add support for Truly NT35597 panel driver

PATCH Superseded Abhinav Kumar 3 participants 8 messages Sep 20, 2018 – Sep 27, 2018

Subsystems (5)

v8 of 10 Superseded Latest is v10 →

lore
Share & tools
lore
#0 lore raw

PATCH v8 1/2 drm/panel: Add support for Truly NT35597 panel driver

From: "[email protected]" <[email protected]>

Add support for Truly NT35597 panel driver used
in MSM reference platforms.

This panel driver supports both single DSI and dual DSI modes.

However, this patch series adds support only for
dual DSI mode.

Changes in v8:
- Remove video mode config and headers
- Remove unused macros
- Try to avoid multi-lines wherever possible
- Fix comments locations and make it concise
- Fix return points in probe function

---
 drivers/gpu/drm/panel/Kconfig               |   7 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 676 ++++++++++++++++++++++++++++
 3 files changed, 684 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
drivers/gpu/drm/panel/Kconfig +7 -0
index 6020c30..073ffa0 100644
@@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
+	  Video Mode panel
 endmenu
drivers/gpu/drm/panel/Makefile +1 -0
index 5ccaaa9..80fd19f 100644
@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +676 -0

676 lines not on this page · raw message

Signature · 7 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#1 lore raw

PATCH v8 2/2 dt-bindings: Add Truly NT35597 panel driver bindings

From: "[email protected]" <[email protected]>

Add the device tree bindings for Truly NT35597 panel driver. This panel driver supports both single DSI and dual DSI.

However, this patch series supports only dual DSI.

Changes in v8:
- None

---
 .../devicetree/bindings/display/truly,nt35597.txt  | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/truly,nt35597.txt
Documentation/devicetree/bindings/display/truly,nt35597.txt new file +60 -0
new file mode 100644
index 0000000..46b29eb
@@ -0,0 +1,60 @@
+Truly model NT35597 DSI display driver
+
+The Truly NT35597 is a generic display driver, currently only configured
+for use in the 2K display on the Qualcomm SDM845.
+
+Required properties:
+- compatible: should be "truly,nt35597-2K-display"
+- vdda-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply
+- vdispp-supply: phandle of the regulator that provides the supply voltage
+  for positive LCD bias
+- vdispn-supply: phandle of the regulator that provides the supply voltage
+  for negative LCD bias
+- reset-gpios: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
+  (active low)
+- mode-gpios: phandle of the gpio for choosing the mode of the display
+  for single DSI or Dual DSI
+  (active high)
+  This should be low for dual DSI and high for single DSI mode
+- ports: This device has two video ports driven by two DSIs. Their connections
+  are modelled using the OF graph bindings specified in
+  Documentation/devicetree/bindings/graph.txt.
+  - port@0: DSI input port driven by master DSI
+  - port@1: DSI input port driven by secondary DSI
+
+Example:
+
+	dsi@ae94000 {
+		panel@0 {
+			compatible = "truly,nt35597-2K-display";
+			reg = <0>;
+			vdda-supply = <&pm8998_l14>;
+			vdispp-supply = <&lab_regulator>;
+			vdispn-supply = <&ibb_regulator>;
+			pinctrl-names = "default", "suspend";
+			pinctrl-0 = <&dpu_dsi_active>;
+			pinctrl-1 = <&dpu_dsi_suspend>;
+
+			reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+			mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					panel0_in: endpoint {
+						remote-endpoint = <&dsi0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					panel1_in: endpoint {
+						remote-endpoint = <&dsi1_out>;
+					};
+				};
+			};
+		};
+	};
Signature · 7 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Reviewed-by on v8 2/2
#2 lore raw

Re: [PATCH v8 2/2] dt-bindings: Add Truly NT35597 panel driver bindings

Quoted 1 line · Abhinav Kumar

From: "[email protected]" <[email protected]>

JFYI, this is going to munge your Author name. This can be fixed up when the patch is applied, so probably not worth a v9.

Quoted 85 lines

Add the device tree bindings for Truly NT35597 panel driver. This panel driver supports both single DSI and dual DSI.

However, this patch series supports only dual DSI.

Changes in v8:
- None

---
 .../devicetree/bindings/display/truly,nt35597.txt  | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/truly,nt35597.txt
Documentation/devicetree/bindings/display/truly,nt35597.txt new file +60 -0
new file mode 100644
index 0000000..46b29eb
@@ -0,0 +1,60 @@
+Truly model NT35597 DSI display driver
+
+The Truly NT35597 is a generic display driver, currently only configured
+for use in the 2K display on the Qualcomm SDM845.
+
+Required properties:
+- compatible: should be "truly,nt35597-2K-display"
+- vdda-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply
+- vdispp-supply: phandle of the regulator that provides the supply voltage
+  for positive LCD bias
+- vdispn-supply: phandle of the regulator that provides the supply voltage
+  for negative LCD bias
+- reset-gpios: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
+  (active low)
+- mode-gpios: phandle of the gpio for choosing the mode of the display
+  for single DSI or Dual DSI
+  (active high)
+  This should be low for dual DSI and high for single DSI mode
+- ports: This device has two video ports driven by two DSIs. Their connections
+  are modelled using the OF graph bindings specified in
+  Documentation/devicetree/bindings/graph.txt.
+  - port@0: DSI input port driven by master DSI
+  - port@1: DSI input port driven by secondary DSI
+
+Example:
+
+	dsi@ae94000 {
+		panel@0 {
+			compatible = "truly,nt35597-2K-display";
+			reg = <0>;
+			vdda-supply = <&pm8998_l14>;
+			vdispp-supply = <&lab_regulator>;
+			vdispn-supply = <&ibb_regulator>;
+			pinctrl-names = "default", "suspend";
+			pinctrl-0 = <&dpu_dsi_active>;
+			pinctrl-1 = <&dpu_dsi_suspend>;
+
+			reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+			mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					panel0_in: endpoint {
+						remote-endpoint = <&dsi0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					panel1_in: endpoint {
+						remote-endpoint = <&dsi1_out>;
+					};
+				};
+			};
+		};
+	};
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#3 lore raw

Re: [PATCH v8 2/2] dt-bindings: Add Truly NT35597 panel driver bindings

In reply to Abhinav Kumar
Quoted 11 lines · Abhinav Kumar

From: "[email protected]" <[email protected]>

Add the device tree bindings for Truly NT35597 panel driver. This panel driver supports both single DSI and dual DSI.

However, this patch series supports only dual DSI.

Changes in v8:
- None

Quoted 75 lines
---
 .../devicetree/bindings/display/truly,nt35597.txt  | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/truly,nt35597.txt
Documentation/devicetree/bindings/display/truly,nt35597.txt new file +60 -0
new file mode 100644
index 0000000..46b29eb
@@ -0,0 +1,60 @@
+Truly model NT35597 DSI display driver
+
+The Truly NT35597 is a generic display driver, currently only configured
+for use in the 2K display on the Qualcomm SDM845.
+
+Required properties:
+- compatible: should be "truly,nt35597-2K-display"
+- vdda-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply
+- vdispp-supply: phandle of the regulator that provides the supply voltage
+  for positive LCD bias
+- vdispn-supply: phandle of the regulator that provides the supply voltage
+  for negative LCD bias
+- reset-gpios: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
+  (active low)
+- mode-gpios: phandle of the gpio for choosing the mode of the display
+  for single DSI or Dual DSI
+  (active high)
+  This should be low for dual DSI and high for single DSI mode
+- ports: This device has two video ports driven by two DSIs. Their connections
+  are modelled using the OF graph bindings specified in
+  Documentation/devicetree/bindings/graph.txt.
+  - port@0: DSI input port driven by master DSI
+  - port@1: DSI input port driven by secondary DSI
+
+Example:
+
+	dsi@ae94000 {
+		panel@0 {
+			compatible = "truly,nt35597-2K-display";
+			reg = <0>;
+			vdda-supply = <&pm8998_l14>;
+			vdispp-supply = <&lab_regulator>;
+			vdispn-supply = <&ibb_regulator>;
+			pinctrl-names = "default", "suspend";
+			pinctrl-0 = <&dpu_dsi_active>;
+			pinctrl-1 = <&dpu_dsi_suspend>;
+
+			reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+			mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					panel0_in: endpoint {
+						remote-endpoint = <&dsi0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					panel1_in: endpoint {
+						remote-endpoint = <&dsi1_out>;
+					};
+				};
+			};
+		};
+	};
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Reviewed-by on v8 1/2
#4 lore raw
In reply to Abhinav Kumar
Quoted 11 lines · Abhinav Kumar

From: "[email protected]" <[email protected]>

Add support for Truly NT35597 panel driver used
in MSM reference platforms.

This panel driver supports both single DSI and dual DSI modes.

However, this patch series adds support only for
dual DSI mode.

Quoted 6 lines

Changes in v8:
- Remove video mode config and headers
- Remove unused macros
- Try to avoid multi-lines wherever possible
- Fix comments locations and make it concise
- Fix return points in probe function

Thanks for revising!

Quoted 721 lines
---
 drivers/gpu/drm/panel/Kconfig               |   7 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 676 ++++++++++++++++++++++++++++
 3 files changed, 684 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
drivers/gpu/drm/panel/Kconfig +7 -0
index 6020c30..073ffa0 100644
@@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
+	  Video Mode panel
 endmenu
drivers/gpu/drm/panel/Makefile +1 -0
index 5ccaaa9..80fd19f 100644
@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +676 -0
new file mode 100644
index 0000000..c9e09e2
@@ -0,0 +1,676 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/of_device.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>
+
+static const char * const regulator_names[] = {
+	"vdda",
+	"vdispp",
+	"vdispn",
+};
+
+static unsigned long const regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000,
+};
+
+static unsigned long const regulator_disable_loads[] = {
+	80,
+	100,
+	100,
+};
+
+struct nt35597_config {
+	u32 width_mm;
+	u32 height_mm;
+	const char *panel_name;
+	const void *panel_on_cmds;
+	u32 num_on_cmds;
+	const struct drm_display_mode *dm;
+};
+
+struct truly_nt35597 {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *mode_gpio;
+
+	struct backlight_device *backlight;
+
+	struct mipi_dsi_device *dsi[2];
+
+	const struct nt35597_config *config;
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel *panel)
+{
+	return container_of(panel, struct truly_nt35597, panel);
+}
+
+struct cmd_set {
+	u8 commands[4];
+	u8 size;
+};
+
+static struct cmd_set qcom_2k_panel_magic_cmds[] = {
+	/* CMD2_P0 */
+	{ { 0xff, 0x20 }, 2 },
+	{ { 0xfb, 0x01 }, 2 },
+	{ { 0x00, 0x01 }, 2 },
+	{ { 0x01, 0x55 }, 2 },
+	{ { 0x02, 0x45 }, 2 },
+	{ { 0x05, 0x40 }, 2 },
+	{ { 0x06, 0x19 }, 2 },
+	{ { 0x07, 0x1e }, 2 },
+	{ { 0x0b, 0x73 }, 2 },
+	{ { 0x0c, 0x73 }, 2 },
+	{ { 0x0e, 0xb0 }, 2 },
+	{ { 0x0f, 0xae }, 2 },
+	{ { 0x11, 0xb8 }, 2 },
+	{ { 0x13, 0x00 }, 2 },
+	{ { 0x58, 0x80 }, 2 },
+	{ { 0x59, 0x01 }, 2 },
+	{ { 0x5a, 0x00 }, 2 },
+	{ { 0x5b, 0x01 }, 2 },
+	{ { 0x5c, 0x80 }, 2 },
+	{ { 0x5d, 0x81 }, 2 },
+	{ { 0x5e, 0x00 }, 2 },
+	{ { 0x5f, 0x01 }, 2 },
+	{ { 0x72, 0x11 }, 2 },
+	{ { 0x68, 0x03 }, 2 },
+	/* CMD2_P4 */
+	{ { 0xFF, 0x24 }, 2 },
+	{ { 0xFB, 0x01 }, 2 },
+	{ { 0x00, 0x1C }, 2 },
+	{ { 0x01, 0x0B }, 2 },
+	{ { 0x02, 0x0C }, 2 },
+	{ { 0x03, 0x01 }, 2 },
+	{ { 0x04, 0x0F }, 2 },
+	{ { 0x05, 0x10 }, 2 },
+	{ { 0x06, 0x10 }, 2 },
+	{ { 0x07, 0x10 }, 2 },
+	{ { 0x08, 0x89 }, 2 },
+	{ { 0x09, 0x8A }, 2 },
+	{ { 0x0A, 0x13 }, 2 },
+	{ { 0x0B, 0x13 }, 2 },
+	{ { 0x0C, 0x15 }, 2 },
+	{ { 0x0D, 0x15 }, 2 },
+	{ { 0x0E, 0x17 }, 2 },
+	{ { 0x0F, 0x17 }, 2 },
+	{ { 0x10, 0x1C }, 2 },
+	{ { 0x11, 0x0B }, 2 },
+	{ { 0x12, 0x0C }, 2 },
+	{ { 0x13, 0x01 }, 2 },
+	{ { 0x14, 0x0F }, 2 },
+	{ { 0x15, 0x10 }, 2 },
+	{ { 0x16, 0x10 }, 2 },
+	{ { 0x17, 0x10 }, 2 },
+	{ { 0x18, 0x89 }, 2 },
+	{ { 0x19, 0x8A }, 2 },
+	{ { 0x1A, 0x13 }, 2 },
+	{ { 0x1B, 0x13 }, 2 },
+	{ { 0x1C, 0x15 }, 2 },
+	{ { 0x1D, 0x15 }, 2 },
+	{ { 0x1E, 0x17 }, 2 },
+	{ { 0x1F, 0x17 }, 2 },
+	/* STV */
+	{ { 0x20, 0x40 }, 2 },
+	{ { 0x21, 0x01 }, 2 },
+	{ { 0x22, 0x00 }, 2 },
+	{ { 0x23, 0x40 }, 2 },
+	{ { 0x24, 0x40 }, 2 },
+	{ { 0x25, 0x6D }, 2 },
+	{ { 0x26, 0x40 }, 2 },
+	{ { 0x27, 0x40 }, 2 },
+	/* Vend */
+	{ { 0xE0, 0x00 }, 2 },
+	{ { 0xDC, 0x21 }, 2 },
+	{ { 0xDD, 0x22 }, 2 },
+	{ { 0xDE, 0x07 }, 2 },
+	{ { 0xDF, 0x07 }, 2 },
+	{ { 0xE3, 0x6D }, 2 },
+	{ { 0xE1, 0x07 }, 2 },
+	{ { 0xE2, 0x07 }, 2 },
+	/* UD */
+	{ { 0x29, 0xD8 }, 2 },
+	{ { 0x2A, 0x2A }, 2 },
+	/* CLK */
+	{ { 0x4B, 0x03 }, 2 },
+	{ { 0x4C, 0x11 }, 2 },
+	{ { 0x4D, 0x10 }, 2 },
+	{ { 0x4E, 0x01 }, 2 },
+	{ { 0x4F, 0x01 }, 2 },
+	{ { 0x50, 0x10 }, 2 },
+	{ { 0x51, 0x00 }, 2 },
+	{ { 0x52, 0x80 }, 2 },
+	{ { 0x53, 0x00 }, 2 },
+	{ { 0x56, 0x00 }, 2 },
+	{ { 0x54, 0x07 }, 2 },
+	{ { 0x58, 0x07 }, 2 },
+	{ { 0x55, 0x25 }, 2 },
+	/* Reset XDONB */
+	{ { 0x5B, 0x43 }, 2 },
+	{ { 0x5C, 0x00 }, 2 },
+	{ { 0x5F, 0x73 }, 2 },
+	{ { 0x60, 0x73 }, 2 },
+	{ { 0x63, 0x22 }, 2 },
+	{ { 0x64, 0x00 }, 2 },
+	{ { 0x67, 0x08 }, 2 },
+	{ { 0x68, 0x04 }, 2 },
+	/* Resolution:1440x2560 */
+	{ { 0x72, 0x02 }, 2 },
+	/* mux */
+	{ { 0x7A, 0x80 }, 2 },
+	{ { 0x7B, 0x91 }, 2 },
+	{ { 0x7C, 0xD8 }, 2 },
+	{ { 0x7D, 0x60 }, 2 },
+	{ { 0x7F, 0x15 }, 2 },
+	{ { 0x75, 0x15 }, 2 },
+	/* ABOFF */
+	{ { 0xB3, 0xC0 }, 2 },
+	{ { 0xB4, 0x00 }, 2 },
+	{ { 0xB5, 0x00 }, 2 },
+	/* Source EQ */
+	{ { 0x78, 0x00 }, 2 },
+	{ { 0x79, 0x00 }, 2 },
+	{ { 0x80, 0x00 }, 2 },
+	{ { 0x83, 0x00 }, 2 },
+	/* FP BP */
+	{ { 0x93, 0x0A }, 2 },
+	{ { 0x94, 0x0A }, 2 },
+	/* Inversion Type */
+	{ { 0x8A, 0x00 }, 2 },
+	{ { 0x9B, 0xFF }, 2 },
+	/* IMGSWAP =1 @PortSwap=1 */
+	{ { 0x9D, 0xB0 }, 2 },
+	{ { 0x9F, 0x63 }, 2 },
+	{ { 0x98, 0x10 }, 2 },
+	/* FRM */
+	{ { 0xEC, 0x00 }, 2 },
+	/* CMD1 */
+	{ { 0xFF, 0x10 }, 2 },
+	/* VBP+VSA=,VFP = 10H */
+	{ { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
+	/* FTE on */
+	{ { 0x35, 0x00 }, 2 },
+	/* EN_BK =1(auto black) */
+	{ { 0xE5, 0x01 }, 2 },
+	/* CMD mode(10) VDO mode(03) */
+	{ { 0xBB, 0x03 }, 2 },
+	/* Non Reload MTP */
+	{ { 0xFB, 0x01 }, 2 },
+};
+
+static int truly_dcs_write(struct drm_panel *panel, u32 command)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write(ctx->dsi[i], command, NULL, 0);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd 0x%x failed for dsi = %d\n",
+				command, i);
+		}
+	}
+
+	return ret;
+}
+
+static int truly_dcs_write_buf(struct drm_panel *panel,
+	u32 size, u8 *buf)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], buf, size);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"failed to tx cmd [%d], err: %d\n", i, ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int truly_35597_power_on(struct truly_nt35597 *ctx)
+{
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+					regulator_enable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Reset sequence of truly panel requires the panel to be
+	 * out of reset for 10ms, followed by being held in reset
+	 * for 10ms and then out again
+	 */
+	gpiod_set_value(ctx->reset_gpio, 0);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	return 0;
+}
+
+static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
+{
+	int ret = 0;
+	int i;
+
+	gpiod_set_value(ctx->reset_gpio, 1);
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+				regulator_disable_loads[i]);
+		if (ret) {
+			DRM_DEV_ERROR(ctx->dev,
+				"regulator_set_load failed %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_bulk_disable failed %d\n", ret);
+	}
+	return ret;
+}
+
+static int truly_nt35597_disable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_disable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+				ret);
+	}
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int truly_nt35597_unprepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi[0]->mode_flags = 0;
+	ctx->dsi[1]->mode_flags = 0;
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n", ret);
+	}
+
+	ret = truly_nt35597_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int truly_nt35597_prepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+	int i;
+	struct cmd_set *panel_on_cmds;
+	const struct nt35597_config *config;
+	u32 num_cmds;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = truly_35597_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
+	ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	config = ctx->config;
+	panel_on_cmds = (struct cmd_set *)config->panel_on_cmds;
+	num_cmds = config->num_on_cmds;
+
+	for (i = 0; i < num_cmds; i++) {
+		ret = truly_dcs_write_buf(panel,
+				panel_on_cmds[i].size,
+					panel_on_cmds[i].commands);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd set tx failed i = %d ret = %d\n",
+					i, ret);
+			goto power_off;
+		}
+	}
+
+	ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n", ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending set_display_on DCS command */
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+
+power_off:
+	if (truly_nt35597_power_off(ctx))
+		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
+	return ret;
+}
+
+static int truly_nt35597_enable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_enable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+						  ret);
+	}
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int truly_nt35597_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	struct drm_display_mode *mode;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = config->width_mm;
+	connector->display_info.height_mm = config->height_mm;
+	drm_mode_copy(mode, config->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
+	.disable = truly_nt35597_disable,
+	.unprepare = truly_nt35597_unprepare,
+	.prepare = truly_nt35597_prepare,
+	.enable = truly_nt35597_enable,
+	.get_modes = truly_nt35597_get_modes,
+};
+
+static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
+{
+	struct device *dev = ctx->dev;
+	int ret, i;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+			PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->mode_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
+			PTR_ERR(ctx->mode_gpio));
+		return PTR_ERR(ctx->mode_gpio);
+	}
+
+	/* dual port */
+	gpiod_set_value(ctx->mode_gpio, 0);
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = dev;
+	ctx->panel.funcs = &truly_nt35597_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	return 0;
+}
+
+static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
+	.name = "1440x2560",
+	.clock = 268316,
+	.hdisplay = 1440,
+	.hsync_start = 1440 + 200,
+	.hsync_end = 1440 + 200 + 32,
+	.htotal = 1440 + 200 + 32 + 64,
+	.vdisplay = 2560,
+	.vsync_start = 2560 + 8,
+	.vsync_end = 2560 + 8 + 1,
+	.vtotal = 2560 + 8 + 1 + 7,
+	.vrefresh = 60,
+	.flags = 0,
+};
+
+static const struct nt35597_config nt35597_dir = {
+	.width_mm = 74,
+	.height_mm = 131,
+	.panel_name = "qcom_sdm845_mtp_2k_panel",
+	.dm = &qcom_sdm845_mtp_2k_mode,
+	.panel_on_cmds = qcom_2k_panel_magic_cmds,
+	.num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
+};
+
+static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct truly_nt35597 *ctx;
+	struct mipi_dsi_device *dsi1_device;
+	struct device_node *dsi1;
+	struct mipi_dsi_host *dsi1_host;
+	struct mipi_dsi_device *dsi_dev;
+	int ret = 0;
+	int i;
+
+	const struct mipi_dsi_device_info info = {
+		.type = "trulynt35597",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+
+	if (!ctx)
+		return -ENOMEM;
+
+	/*
+	 * This device represents itself as one with
+	 * two input ports which are fed by the output
+	 * ports of the two DSI controllers . The DSI0
+	 * is the master controller and has most of the
+	 * panel related info in its child node.
+	 */
+
+	ctx->config = of_device_get_match_data(dev);
+
+	if (!ctx->config) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+	if (!dsi1) {
+		DRM_DEV_ERROR(dev,
+			"failed to get remote node for dsi1_device\n");
+		return -ENODEV;
+	}
+
+	dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
+	of_node_put(dsi1);
+	if (!dsi1_host) {
+		DRM_DEV_ERROR(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	/* register the second DSI device */
+	dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
+	if (IS_ERR(dsi1_device)) {
+		DRM_DEV_ERROR(dev, "failed to create dsi device\n");
+		return PTR_ERR(dsi);
+	}
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi[0] = dsi;
+	ctx->dsi[1] = dsi1_device;
+
+	ret = truly_nt35597_panel_add(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to add panel\n");
+		goto err_panel_add;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		dsi_dev = ctx->dsi[i];
+		dsi_dev->lanes = 4;
+		dsi_dev->format = MIPI_DSI_FMT_RGB888;
+		dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+			MIPI_DSI_CLOCK_NON_CONTINUOUS;
+		ret = mipi_dsi_attach(dsi_dev);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dev,
+				"dsi attach failed i = %d\n", i);
+				goto err_dsi_attach;
+		}
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+err_panel_add:
+	mipi_dsi_device_unregister(dsi1_device);
+	return ret;
+}
+
+static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
+{
+	struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi[0])
+		mipi_dsi_detach(ctx->dsi[0]);
+	if (ctx->dsi[1]) {
+		mipi_dsi_detach(ctx->dsi[1]);
+		mipi_dsi_device_unregister(ctx->dsi[1]);
+	}
+
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id truly_nt35597_of_match[] = {
+	{	.compatible = "truly,nt35597-2K-display",
+		.data = &nt35597_dir,
+	},
+
+	{ }
+};
+MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
+
+static struct mipi_dsi_driver truly_nt35597_driver = {
+	.driver = {
+		.name = "panel_truly_nt35597",
+		.of_match_table = truly_nt35597_of_match,
+	},
+	.probe = truly_nt35597_probe,
+	.remove = truly_nt35597_remove,
+};
+module_mipi_dsi_driver(truly_nt35597_driver);
+
+MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#5 lore raw
In reply to Abhinav Kumar
Quoted 18 lines · Abhinav Kumar

From: "[email protected]" <[email protected]>

Add support for Truly NT35597 panel driver used
in MSM reference platforms.

This panel driver supports both single DSI and dual DSI modes.

However, this patch series adds support only for
dual DSI mode.

Changes in v8:
- Remove video mode config and headers
- Remove unused macros
- Try to avoid multi-lines wherever possible
- Fix comments locations and make it concise
- Fix return points in probe function

Quoted 2 lines

Adding Cc: [email protected] so Rob sees it in his patchwork queue.

Sean

Quoted 718 lines
---
 drivers/gpu/drm/panel/Kconfig               |   7 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 676 ++++++++++++++++++++++++++++
 3 files changed, 684 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
drivers/gpu/drm/panel/Kconfig +7 -0
index 6020c30..073ffa0 100644
@@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
+	  Video Mode panel
 endmenu
drivers/gpu/drm/panel/Makefile +1 -0
index 5ccaaa9..80fd19f 100644
@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +676 -0
new file mode 100644
index 0000000..c9e09e2
@@ -0,0 +1,676 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/of_device.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>
+
+static const char * const regulator_names[] = {
+	"vdda",
+	"vdispp",
+	"vdispn",
+};
+
+static unsigned long const regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000,
+};
+
+static unsigned long const regulator_disable_loads[] = {
+	80,
+	100,
+	100,
+};
+
+struct nt35597_config {
+	u32 width_mm;
+	u32 height_mm;
+	const char *panel_name;
+	const void *panel_on_cmds;
+	u32 num_on_cmds;
+	const struct drm_display_mode *dm;
+};
+
+struct truly_nt35597 {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *mode_gpio;
+
+	struct backlight_device *backlight;
+
+	struct mipi_dsi_device *dsi[2];
+
+	const struct nt35597_config *config;
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel *panel)
+{
+	return container_of(panel, struct truly_nt35597, panel);
+}
+
+struct cmd_set {
+	u8 commands[4];
+	u8 size;
+};
+
+static struct cmd_set qcom_2k_panel_magic_cmds[] = {
+	/* CMD2_P0 */
+	{ { 0xff, 0x20 }, 2 },
+	{ { 0xfb, 0x01 }, 2 },
+	{ { 0x00, 0x01 }, 2 },
+	{ { 0x01, 0x55 }, 2 },
+	{ { 0x02, 0x45 }, 2 },
+	{ { 0x05, 0x40 }, 2 },
+	{ { 0x06, 0x19 }, 2 },
+	{ { 0x07, 0x1e }, 2 },
+	{ { 0x0b, 0x73 }, 2 },
+	{ { 0x0c, 0x73 }, 2 },
+	{ { 0x0e, 0xb0 }, 2 },
+	{ { 0x0f, 0xae }, 2 },
+	{ { 0x11, 0xb8 }, 2 },
+	{ { 0x13, 0x00 }, 2 },
+	{ { 0x58, 0x80 }, 2 },
+	{ { 0x59, 0x01 }, 2 },
+	{ { 0x5a, 0x00 }, 2 },
+	{ { 0x5b, 0x01 }, 2 },
+	{ { 0x5c, 0x80 }, 2 },
+	{ { 0x5d, 0x81 }, 2 },
+	{ { 0x5e, 0x00 }, 2 },
+	{ { 0x5f, 0x01 }, 2 },
+	{ { 0x72, 0x11 }, 2 },
+	{ { 0x68, 0x03 }, 2 },
+	/* CMD2_P4 */
+	{ { 0xFF, 0x24 }, 2 },
+	{ { 0xFB, 0x01 }, 2 },
+	{ { 0x00, 0x1C }, 2 },
+	{ { 0x01, 0x0B }, 2 },
+	{ { 0x02, 0x0C }, 2 },
+	{ { 0x03, 0x01 }, 2 },
+	{ { 0x04, 0x0F }, 2 },
+	{ { 0x05, 0x10 }, 2 },
+	{ { 0x06, 0x10 }, 2 },
+	{ { 0x07, 0x10 }, 2 },
+	{ { 0x08, 0x89 }, 2 },
+	{ { 0x09, 0x8A }, 2 },
+	{ { 0x0A, 0x13 }, 2 },
+	{ { 0x0B, 0x13 }, 2 },
+	{ { 0x0C, 0x15 }, 2 },
+	{ { 0x0D, 0x15 }, 2 },
+	{ { 0x0E, 0x17 }, 2 },
+	{ { 0x0F, 0x17 }, 2 },
+	{ { 0x10, 0x1C }, 2 },
+	{ { 0x11, 0x0B }, 2 },
+	{ { 0x12, 0x0C }, 2 },
+	{ { 0x13, 0x01 }, 2 },
+	{ { 0x14, 0x0F }, 2 },
+	{ { 0x15, 0x10 }, 2 },
+	{ { 0x16, 0x10 }, 2 },
+	{ { 0x17, 0x10 }, 2 },
+	{ { 0x18, 0x89 }, 2 },
+	{ { 0x19, 0x8A }, 2 },
+	{ { 0x1A, 0x13 }, 2 },
+	{ { 0x1B, 0x13 }, 2 },
+	{ { 0x1C, 0x15 }, 2 },
+	{ { 0x1D, 0x15 }, 2 },
+	{ { 0x1E, 0x17 }, 2 },
+	{ { 0x1F, 0x17 }, 2 },
+	/* STV */
+	{ { 0x20, 0x40 }, 2 },
+	{ { 0x21, 0x01 }, 2 },
+	{ { 0x22, 0x00 }, 2 },
+	{ { 0x23, 0x40 }, 2 },
+	{ { 0x24, 0x40 }, 2 },
+	{ { 0x25, 0x6D }, 2 },
+	{ { 0x26, 0x40 }, 2 },
+	{ { 0x27, 0x40 }, 2 },
+	/* Vend */
+	{ { 0xE0, 0x00 }, 2 },
+	{ { 0xDC, 0x21 }, 2 },
+	{ { 0xDD, 0x22 }, 2 },
+	{ { 0xDE, 0x07 }, 2 },
+	{ { 0xDF, 0x07 }, 2 },
+	{ { 0xE3, 0x6D }, 2 },
+	{ { 0xE1, 0x07 }, 2 },
+	{ { 0xE2, 0x07 }, 2 },
+	/* UD */
+	{ { 0x29, 0xD8 }, 2 },
+	{ { 0x2A, 0x2A }, 2 },
+	/* CLK */
+	{ { 0x4B, 0x03 }, 2 },
+	{ { 0x4C, 0x11 }, 2 },
+	{ { 0x4D, 0x10 }, 2 },
+	{ { 0x4E, 0x01 }, 2 },
+	{ { 0x4F, 0x01 }, 2 },
+	{ { 0x50, 0x10 }, 2 },
+	{ { 0x51, 0x00 }, 2 },
+	{ { 0x52, 0x80 }, 2 },
+	{ { 0x53, 0x00 }, 2 },
+	{ { 0x56, 0x00 }, 2 },
+	{ { 0x54, 0x07 }, 2 },
+	{ { 0x58, 0x07 }, 2 },
+	{ { 0x55, 0x25 }, 2 },
+	/* Reset XDONB */
+	{ { 0x5B, 0x43 }, 2 },
+	{ { 0x5C, 0x00 }, 2 },
+	{ { 0x5F, 0x73 }, 2 },
+	{ { 0x60, 0x73 }, 2 },
+	{ { 0x63, 0x22 }, 2 },
+	{ { 0x64, 0x00 }, 2 },
+	{ { 0x67, 0x08 }, 2 },
+	{ { 0x68, 0x04 }, 2 },
+	/* Resolution:1440x2560 */
+	{ { 0x72, 0x02 }, 2 },
+	/* mux */
+	{ { 0x7A, 0x80 }, 2 },
+	{ { 0x7B, 0x91 }, 2 },
+	{ { 0x7C, 0xD8 }, 2 },
+	{ { 0x7D, 0x60 }, 2 },
+	{ { 0x7F, 0x15 }, 2 },
+	{ { 0x75, 0x15 }, 2 },
+	/* ABOFF */
+	{ { 0xB3, 0xC0 }, 2 },
+	{ { 0xB4, 0x00 }, 2 },
+	{ { 0xB5, 0x00 }, 2 },
+	/* Source EQ */
+	{ { 0x78, 0x00 }, 2 },
+	{ { 0x79, 0x00 }, 2 },
+	{ { 0x80, 0x00 }, 2 },
+	{ { 0x83, 0x00 }, 2 },
+	/* FP BP */
+	{ { 0x93, 0x0A }, 2 },
+	{ { 0x94, 0x0A }, 2 },
+	/* Inversion Type */
+	{ { 0x8A, 0x00 }, 2 },
+	{ { 0x9B, 0xFF }, 2 },
+	/* IMGSWAP =1 @PortSwap=1 */
+	{ { 0x9D, 0xB0 }, 2 },
+	{ { 0x9F, 0x63 }, 2 },
+	{ { 0x98, 0x10 }, 2 },
+	/* FRM */
+	{ { 0xEC, 0x00 }, 2 },
+	/* CMD1 */
+	{ { 0xFF, 0x10 }, 2 },
+	/* VBP+VSA=,VFP = 10H */
+	{ { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
+	/* FTE on */
+	{ { 0x35, 0x00 }, 2 },
+	/* EN_BK =1(auto black) */
+	{ { 0xE5, 0x01 }, 2 },
+	/* CMD mode(10) VDO mode(03) */
+	{ { 0xBB, 0x03 }, 2 },
+	/* Non Reload MTP */
+	{ { 0xFB, 0x01 }, 2 },
+};
+
+static int truly_dcs_write(struct drm_panel *panel, u32 command)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write(ctx->dsi[i], command, NULL, 0);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd 0x%x failed for dsi = %d\n",
+				command, i);
+		}
+	}
+
+	return ret;
+}
+
+static int truly_dcs_write_buf(struct drm_panel *panel,
+	u32 size, u8 *buf)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], buf, size);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"failed to tx cmd [%d], err: %d\n", i, ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int truly_35597_power_on(struct truly_nt35597 *ctx)
+{
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+					regulator_enable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Reset sequence of truly panel requires the panel to be
+	 * out of reset for 10ms, followed by being held in reset
+	 * for 10ms and then out again
+	 */
+	gpiod_set_value(ctx->reset_gpio, 0);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	return 0;
+}
+
+static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
+{
+	int ret = 0;
+	int i;
+
+	gpiod_set_value(ctx->reset_gpio, 1);
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+				regulator_disable_loads[i]);
+		if (ret) {
+			DRM_DEV_ERROR(ctx->dev,
+				"regulator_set_load failed %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_bulk_disable failed %d\n", ret);
+	}
+	return ret;
+}
+
+static int truly_nt35597_disable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_disable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+				ret);
+	}
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int truly_nt35597_unprepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi[0]->mode_flags = 0;
+	ctx->dsi[1]->mode_flags = 0;
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n", ret);
+	}
+
+	ret = truly_nt35597_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int truly_nt35597_prepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+	int i;
+	struct cmd_set *panel_on_cmds;
+	const struct nt35597_config *config;
+	u32 num_cmds;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = truly_35597_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
+	ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	config = ctx->config;
+	panel_on_cmds = (struct cmd_set *)config->panel_on_cmds;
+	num_cmds = config->num_on_cmds;
+
+	for (i = 0; i < num_cmds; i++) {
+		ret = truly_dcs_write_buf(panel,
+				panel_on_cmds[i].size,
+					panel_on_cmds[i].commands);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd set tx failed i = %d ret = %d\n",
+					i, ret);
+			goto power_off;
+		}
+	}
+
+	ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n", ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending set_display_on DCS command */
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+
+power_off:
+	if (truly_nt35597_power_off(ctx))
+		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
+	return ret;
+}
+
+static int truly_nt35597_enable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_enable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+						  ret);
+	}
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int truly_nt35597_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	struct drm_display_mode *mode;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = config->width_mm;
+	connector->display_info.height_mm = config->height_mm;
+	drm_mode_copy(mode, config->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
+	.disable = truly_nt35597_disable,
+	.unprepare = truly_nt35597_unprepare,
+	.prepare = truly_nt35597_prepare,
+	.enable = truly_nt35597_enable,
+	.get_modes = truly_nt35597_get_modes,
+};
+
+static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
+{
+	struct device *dev = ctx->dev;
+	int ret, i;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+			PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->mode_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
+			PTR_ERR(ctx->mode_gpio));
+		return PTR_ERR(ctx->mode_gpio);
+	}
+
+	/* dual port */
+	gpiod_set_value(ctx->mode_gpio, 0);
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = dev;
+	ctx->panel.funcs = &truly_nt35597_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	return 0;
+}
+
+static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
+	.name = "1440x2560",
+	.clock = 268316,
+	.hdisplay = 1440,
+	.hsync_start = 1440 + 200,
+	.hsync_end = 1440 + 200 + 32,
+	.htotal = 1440 + 200 + 32 + 64,
+	.vdisplay = 2560,
+	.vsync_start = 2560 + 8,
+	.vsync_end = 2560 + 8 + 1,
+	.vtotal = 2560 + 8 + 1 + 7,
+	.vrefresh = 60,
+	.flags = 0,
+};
+
+static const struct nt35597_config nt35597_dir = {
+	.width_mm = 74,
+	.height_mm = 131,
+	.panel_name = "qcom_sdm845_mtp_2k_panel",
+	.dm = &qcom_sdm845_mtp_2k_mode,
+	.panel_on_cmds = qcom_2k_panel_magic_cmds,
+	.num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
+};
+
+static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct truly_nt35597 *ctx;
+	struct mipi_dsi_device *dsi1_device;
+	struct device_node *dsi1;
+	struct mipi_dsi_host *dsi1_host;
+	struct mipi_dsi_device *dsi_dev;
+	int ret = 0;
+	int i;
+
+	const struct mipi_dsi_device_info info = {
+		.type = "trulynt35597",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+
+	if (!ctx)
+		return -ENOMEM;
+
+	/*
+	 * This device represents itself as one with
+	 * two input ports which are fed by the output
+	 * ports of the two DSI controllers . The DSI0
+	 * is the master controller and has most of the
+	 * panel related info in its child node.
+	 */
+
+	ctx->config = of_device_get_match_data(dev);
+
+	if (!ctx->config) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+	if (!dsi1) {
+		DRM_DEV_ERROR(dev,
+			"failed to get remote node for dsi1_device\n");
+		return -ENODEV;
+	}
+
+	dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
+	of_node_put(dsi1);
+	if (!dsi1_host) {
+		DRM_DEV_ERROR(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	/* register the second DSI device */
+	dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
+	if (IS_ERR(dsi1_device)) {
+		DRM_DEV_ERROR(dev, "failed to create dsi device\n");
+		return PTR_ERR(dsi);
+	}
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi[0] = dsi;
+	ctx->dsi[1] = dsi1_device;
+
+	ret = truly_nt35597_panel_add(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to add panel\n");
+		goto err_panel_add;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		dsi_dev = ctx->dsi[i];
+		dsi_dev->lanes = 4;
+		dsi_dev->format = MIPI_DSI_FMT_RGB888;
+		dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+			MIPI_DSI_CLOCK_NON_CONTINUOUS;
+		ret = mipi_dsi_attach(dsi_dev);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dev,
+				"dsi attach failed i = %d\n", i);
+				goto err_dsi_attach;
+		}
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+err_panel_add:
+	mipi_dsi_device_unregister(dsi1_device);
+	return ret;
+}
+
+static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
+{
+	struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi[0])
+		mipi_dsi_detach(ctx->dsi[0]);
+	if (ctx->dsi[1]) {
+		mipi_dsi_detach(ctx->dsi[1]);
+		mipi_dsi_device_unregister(ctx->dsi[1]);
+	}
+
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id truly_nt35597_of_match[] = {
+	{	.compatible = "truly,nt35597-2K-display",
+		.data = &nt35597_dir,
+	},
+
+	{ }
+};
+MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
+
+static struct mipi_dsi_driver truly_nt35597_driver = {
+	.driver = {
+		.name = "panel_truly_nt35597",
+		.of_match_table = truly_nt35597_of_match,
+	},
+	.probe = truly_nt35597_probe,
+	.remove = truly_nt35597_remove,
+};
+module_mipi_dsi_driver(truly_nt35597_driver);
+
+MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#6 lore raw
In reply to Abhinav Kumar
Quoted 10 lines · Abhinav Kumar

From: "[email protected]" <[email protected]>

Add support for Truly NT35597 panel driver used
in MSM reference platforms.

This panel driver supports both single DSI and dual DSI modes.

However, this patch series adds support only for
dual DSI mode.

Your lines are very short here. It's usually a good idea to keep the subject line short, but there's no need to wrap this early in the rest of the commit message. It's customary to use up to 72 characters.

Quoted 54 lines

Changes in v8:
- Remove video mode config and headers
- Remove unused macros
- Try to avoid multi-lines wherever possible
- Fix comments locations and make it concise
- Fix return points in probe function

---
 drivers/gpu/drm/panel/Kconfig               |   7 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 676 ++++++++++++++++++++++++++++
 3 files changed, 684 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
drivers/gpu/drm/panel/Kconfig +7 -0
index 6020c30..073ffa0 100644
@@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
+	  Video Mode panel
 endmenu
drivers/gpu/drm/panel/Makefile +1 -0
index 5ccaaa9..80fd19f 100644
@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +6 -0
new file mode 100644
index 0000000..c9e09e2
@@ -0,0 +1,676 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/consumer.h>

drivers/gpu/drm/panel/panel-truly-nt35597.c line 16

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/of_device.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>

The headers should be sorted alphabetically.

Quoted 14 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +14 -0
+
+static const char * const regulator_names[] = {
+	"vdda",
+	"vdispp",
+	"vdispn",
+};
+
+static unsigned long const regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000,
+};
+
+static unsigned long const regulator_disable_loads[] = {

drivers/gpu/drm/panel/panel-truly-nt35597.c line 40

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+	80,
+	100,
+	100,
+};
+
+struct nt35597_config {
+	u32 width_mm;
+	u32 height_mm;
+	const char *panel_name;
+	const void *panel_on_cmds;

Why void *? You define the correct data structure a few lines further down, so you might as well just move that definition up and use the proper data structure here. Then there'd be no need to cast this to struct cmd_set * later on when you use it.

Quoted 23 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +23 -0
+	u32 num_on_cmds;
+	const struct drm_display_mode *dm;
+};
+
+struct truly_nt35597 {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *mode_gpio;
+
+	struct backlight_device *backlight;
+
+	struct mipi_dsi_device *dsi[2];
+
+	const struct nt35597_config *config;
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel *panel)

drivers/gpu/drm/panel/panel-truly-nt35597.c line 73

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+{
+	return container_of(panel, struct truly_nt35597, panel);
+}
+
+struct cmd_set {
+	u8 commands[4];
+	u8 size;
+};
+
+static struct cmd_set qcom_2k_panel_magic_cmds[] = {

static const?

Quoted 493 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +493 -0
+	/* CMD2_P0 */
+	{ { 0xff, 0x20 }, 2 },
+	{ { 0xfb, 0x01 }, 2 },
+	{ { 0x00, 0x01 }, 2 },
+	{ { 0x01, 0x55 }, 2 },
+	{ { 0x02, 0x45 }, 2 },
+	{ { 0x05, 0x40 }, 2 },
+	{ { 0x06, 0x19 }, 2 },
+	{ { 0x07, 0x1e }, 2 },
+	{ { 0x0b, 0x73 }, 2 },
+	{ { 0x0c, 0x73 }, 2 },
+	{ { 0x0e, 0xb0 }, 2 },
+	{ { 0x0f, 0xae }, 2 },
+	{ { 0x11, 0xb8 }, 2 },
+	{ { 0x13, 0x00 }, 2 },
+	{ { 0x58, 0x80 }, 2 },
+	{ { 0x59, 0x01 }, 2 },
+	{ { 0x5a, 0x00 }, 2 },
+	{ { 0x5b, 0x01 }, 2 },
+	{ { 0x5c, 0x80 }, 2 },
+	{ { 0x5d, 0x81 }, 2 },
+	{ { 0x5e, 0x00 }, 2 },
+	{ { 0x5f, 0x01 }, 2 },
+	{ { 0x72, 0x11 }, 2 },
+	{ { 0x68, 0x03 }, 2 },
+	/* CMD2_P4 */
+	{ { 0xFF, 0x24 }, 2 },
+	{ { 0xFB, 0x01 }, 2 },
+	{ { 0x00, 0x1C }, 2 },
+	{ { 0x01, 0x0B }, 2 },
+	{ { 0x02, 0x0C }, 2 },
+	{ { 0x03, 0x01 }, 2 },
+	{ { 0x04, 0x0F }, 2 },
+	{ { 0x05, 0x10 }, 2 },
+	{ { 0x06, 0x10 }, 2 },
+	{ { 0x07, 0x10 }, 2 },
+	{ { 0x08, 0x89 }, 2 },
+	{ { 0x09, 0x8A }, 2 },
+	{ { 0x0A, 0x13 }, 2 },
+	{ { 0x0B, 0x13 }, 2 },
+	{ { 0x0C, 0x15 }, 2 },
+	{ { 0x0D, 0x15 }, 2 },
+	{ { 0x0E, 0x17 }, 2 },
+	{ { 0x0F, 0x17 }, 2 },
+	{ { 0x10, 0x1C }, 2 },
+	{ { 0x11, 0x0B }, 2 },
+	{ { 0x12, 0x0C }, 2 },
+	{ { 0x13, 0x01 }, 2 },
+	{ { 0x14, 0x0F }, 2 },
+	{ { 0x15, 0x10 }, 2 },
+	{ { 0x16, 0x10 }, 2 },
+	{ { 0x17, 0x10 }, 2 },
+	{ { 0x18, 0x89 }, 2 },
+	{ { 0x19, 0x8A }, 2 },
+	{ { 0x1A, 0x13 }, 2 },
+	{ { 0x1B, 0x13 }, 2 },
+	{ { 0x1C, 0x15 }, 2 },
+	{ { 0x1D, 0x15 }, 2 },
+	{ { 0x1E, 0x17 }, 2 },
+	{ { 0x1F, 0x17 }, 2 },
+	/* STV */
+	{ { 0x20, 0x40 }, 2 },
+	{ { 0x21, 0x01 }, 2 },
+	{ { 0x22, 0x00 }, 2 },
+	{ { 0x23, 0x40 }, 2 },
+	{ { 0x24, 0x40 }, 2 },
+	{ { 0x25, 0x6D }, 2 },
+	{ { 0x26, 0x40 }, 2 },
+	{ { 0x27, 0x40 }, 2 },
+	/* Vend */
+	{ { 0xE0, 0x00 }, 2 },
+	{ { 0xDC, 0x21 }, 2 },
+	{ { 0xDD, 0x22 }, 2 },
+	{ { 0xDE, 0x07 }, 2 },
+	{ { 0xDF, 0x07 }, 2 },
+	{ { 0xE3, 0x6D }, 2 },
+	{ { 0xE1, 0x07 }, 2 },
+	{ { 0xE2, 0x07 }, 2 },
+	/* UD */
+	{ { 0x29, 0xD8 }, 2 },
+	{ { 0x2A, 0x2A }, 2 },
+	/* CLK */
+	{ { 0x4B, 0x03 }, 2 },
+	{ { 0x4C, 0x11 }, 2 },
+	{ { 0x4D, 0x10 }, 2 },
+	{ { 0x4E, 0x01 }, 2 },
+	{ { 0x4F, 0x01 }, 2 },
+	{ { 0x50, 0x10 }, 2 },
+	{ { 0x51, 0x00 }, 2 },
+	{ { 0x52, 0x80 }, 2 },
+	{ { 0x53, 0x00 }, 2 },
+	{ { 0x56, 0x00 }, 2 },
+	{ { 0x54, 0x07 }, 2 },
+	{ { 0x58, 0x07 }, 2 },
+	{ { 0x55, 0x25 }, 2 },
+	/* Reset XDONB */
+	{ { 0x5B, 0x43 }, 2 },
+	{ { 0x5C, 0x00 }, 2 },
+	{ { 0x5F, 0x73 }, 2 },
+	{ { 0x60, 0x73 }, 2 },
+	{ { 0x63, 0x22 }, 2 },
+	{ { 0x64, 0x00 }, 2 },
+	{ { 0x67, 0x08 }, 2 },
+	{ { 0x68, 0x04 }, 2 },
+	/* Resolution:1440x2560 */
+	{ { 0x72, 0x02 }, 2 },
+	/* mux */
+	{ { 0x7A, 0x80 }, 2 },
+	{ { 0x7B, 0x91 }, 2 },
+	{ { 0x7C, 0xD8 }, 2 },
+	{ { 0x7D, 0x60 }, 2 },
+	{ { 0x7F, 0x15 }, 2 },
+	{ { 0x75, 0x15 }, 2 },
+	/* ABOFF */
+	{ { 0xB3, 0xC0 }, 2 },
+	{ { 0xB4, 0x00 }, 2 },
+	{ { 0xB5, 0x00 }, 2 },
+	/* Source EQ */
+	{ { 0x78, 0x00 }, 2 },
+	{ { 0x79, 0x00 }, 2 },
+	{ { 0x80, 0x00 }, 2 },
+	{ { 0x83, 0x00 }, 2 },
+	/* FP BP */
+	{ { 0x93, 0x0A }, 2 },
+	{ { 0x94, 0x0A }, 2 },
+	/* Inversion Type */
+	{ { 0x8A, 0x00 }, 2 },
+	{ { 0x9B, 0xFF }, 2 },
+	/* IMGSWAP =1 @PortSwap=1 */
+	{ { 0x9D, 0xB0 }, 2 },
+	{ { 0x9F, 0x63 }, 2 },
+	{ { 0x98, 0x10 }, 2 },
+	/* FRM */
+	{ { 0xEC, 0x00 }, 2 },
+	/* CMD1 */
+	{ { 0xFF, 0x10 }, 2 },
+	/* VBP+VSA=,VFP = 10H */
+	{ { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
+	/* FTE on */
+	{ { 0x35, 0x00 }, 2 },
+	/* EN_BK =1(auto black) */
+	{ { 0xE5, 0x01 }, 2 },
+	/* CMD mode(10) VDO mode(03) */
+	{ { 0xBB, 0x03 }, 2 },
+	/* Non Reload MTP */
+	{ { 0xFB, 0x01 }, 2 },
+};
+
+static int truly_dcs_write(struct drm_panel *panel, u32 command)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write(ctx->dsi[i], command, NULL, 0);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd 0x%x failed for dsi = %d\n",
+				command, i);
+		}
+	}
+
+	return ret;
+}
+
+static int truly_dcs_write_buf(struct drm_panel *panel,
+	u32 size, u8 *buf)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], buf, size);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"failed to tx cmd [%d], err: %d\n", i, ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int truly_35597_power_on(struct truly_nt35597 *ctx)
+{
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+					regulator_enable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Reset sequence of truly panel requires the panel to be
+	 * out of reset for 10ms, followed by being held in reset
+	 * for 10ms and then out again
+	 */
+	gpiod_set_value(ctx->reset_gpio, 0);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	return 0;
+}
+
+static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
+{
+	int ret = 0;
+	int i;
+
+	gpiod_set_value(ctx->reset_gpio, 1);
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+				regulator_disable_loads[i]);
+		if (ret) {
+			DRM_DEV_ERROR(ctx->dev,
+				"regulator_set_load failed %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_bulk_disable failed %d\n", ret);
+	}
+	return ret;
+}
+
+static int truly_nt35597_disable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_disable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+				ret);
+	}
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int truly_nt35597_unprepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi[0]->mode_flags = 0;
+	ctx->dsi[1]->mode_flags = 0;
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n", ret);
+	}
+
+	ret = truly_nt35597_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int truly_nt35597_prepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+	int i;
+	struct cmd_set *panel_on_cmds;
+	const struct nt35597_config *config;
+	u32 num_cmds;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = truly_35597_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
+	ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	config = ctx->config;
+	panel_on_cmds = (struct cmd_set *)config->panel_on_cmds;
+	num_cmds = config->num_on_cmds;
+
+	for (i = 0; i < num_cmds; i++) {
+		ret = truly_dcs_write_buf(panel,
+				panel_on_cmds[i].size,
+					panel_on_cmds[i].commands);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd set tx failed i = %d ret = %d\n",
+					i, ret);
+			goto power_off;
+		}
+	}
+
+	ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n", ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending set_display_on DCS command */
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+
+power_off:
+	if (truly_nt35597_power_off(ctx))
+		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
+	return ret;
+}
+
+static int truly_nt35597_enable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_enable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+						  ret);
+	}
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int truly_nt35597_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	struct drm_display_mode *mode;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = config->width_mm;
+	connector->display_info.height_mm = config->height_mm;
+	drm_mode_copy(mode, config->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
+	.disable = truly_nt35597_disable,
+	.unprepare = truly_nt35597_unprepare,
+	.prepare = truly_nt35597_prepare,
+	.enable = truly_nt35597_enable,
+	.get_modes = truly_nt35597_get_modes,
+};
+
+static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
+{
+	struct device *dev = ctx->dev;
+	int ret, i;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+			PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->mode_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
+			PTR_ERR(ctx->mode_gpio));
+		return PTR_ERR(ctx->mode_gpio);
+	}
+
+	/* dual port */
+	gpiod_set_value(ctx->mode_gpio, 0);
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = dev;
+	ctx->panel.funcs = &truly_nt35597_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	return 0;
+}
+
+static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
+	.name = "1440x2560",
+	.clock = 268316,
+	.hdisplay = 1440,
+	.hsync_start = 1440 + 200,
+	.hsync_end = 1440 + 200 + 32,
+	.htotal = 1440 + 200 + 32 + 64,
+	.vdisplay = 2560,
+	.vsync_start = 2560 + 8,
+	.vsync_end = 2560 + 8 + 1,
+	.vtotal = 2560 + 8 + 1 + 7,
+	.vrefresh = 60,
+	.flags = 0,
+};
+
+static const struct nt35597_config nt35597_dir = {
+	.width_mm = 74,
+	.height_mm = 131,
+	.panel_name = "qcom_sdm845_mtp_2k_panel",
+	.dm = &qcom_sdm845_mtp_2k_mode,
+	.panel_on_cmds = qcom_2k_panel_magic_cmds,
+	.num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
+};
+
+static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct truly_nt35597 *ctx;
+	struct mipi_dsi_device *dsi1_device;
+	struct device_node *dsi1;
+	struct mipi_dsi_host *dsi1_host;
+	struct mipi_dsi_device *dsi_dev;
+	int ret = 0;
+	int i;
+
+	const struct mipi_dsi_device_info info = {
+		.type = "trulynt35597",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+

drivers/gpu/drm/panel/panel-truly-nt35597.c line 576

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+	if (!ctx)
+		return -ENOMEM;
+
+	/*
+	 * This device represents itself as one with
+	 * two input ports which are fed by the output
+	 * ports of the two DSI controllers . The DSI0
+	 * is the master controller and has most of the
+	 * panel related info in its child node.
+	 */

Your comments can be wider. It's typical to wrap at column 78, not earlier.

Quoted 18 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +18 -0
+
+	ctx->config = of_device_get_match_data(dev);
+
+	if (!ctx->config) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+	if (!dsi1) {
+		DRM_DEV_ERROR(dev,
+			"failed to get remote node for dsi1_device\n");
+		return -ENODEV;
+	}
+
+	dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
+	of_node_put(dsi1);
+	if (!dsi1_host) {

drivers/gpu/drm/panel/panel-truly-nt35597.c line 604

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+		DRM_DEV_ERROR(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	/* register the second DSI device */
+	dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
+	if (IS_ERR(dsi1_device)) {
+		DRM_DEV_ERROR(dev, "failed to create dsi device\n");
+		return PTR_ERR(dsi);
+	}

Can you roll in the fix from here:

	https://patchwork.freedesktop.org/patch/245175/
Quoted 14 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +14 -0
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi[0] = dsi;
+	ctx->dsi[1] = dsi1_device;
+
+	ret = truly_nt35597_panel_add(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to add panel\n");
+		goto err_panel_add;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {

drivers/gpu/drm/panel/panel-truly-nt35597.c line 628

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+		dsi_dev = ctx->dsi[i];
+		dsi_dev->lanes = 4;
+		dsi_dev->format = MIPI_DSI_FMT_RGB888;
+		dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+			MIPI_DSI_CLOCK_NON_CONTINUOUS;
+		ret = mipi_dsi_attach(dsi_dev);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dev,
+				"dsi attach failed i = %d\n", i);
+				goto err_dsi_attach;

Indentation is wrong here. The goto should be indented one level less.

Quoted 23 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +23 -0
+		}
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+err_panel_add:
+	mipi_dsi_device_unregister(dsi1_device);
+	return ret;
+}
+
+static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
+{
+	struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi[0])
+		mipi_dsi_detach(ctx->dsi[0]);
+	if (ctx->dsi[1]) {
+		mipi_dsi_detach(ctx->dsi[1]);
+		mipi_dsi_device_unregister(ctx->dsi[1]);
+	}
+

drivers/gpu/drm/panel/panel-truly-nt35597.c line 661

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id truly_nt35597_of_match[] = {
+	{	.compatible = "truly,nt35597-2K-display",
+		.data = &nt35597_dir,
+	},
+
+	{ }

The table is weirdly formatted. The ".compatible = ..." line should be an a separate line, and there should be no blank line before { }.

drivers/gpu/drm/panel/panel-truly-nt35597.c line 667

Quoted 6 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +6 -0
+};
+MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
+
+static struct mipi_dsi_driver truly_nt35597_driver = {
+	.driver = {
+		.name = "panel_truly_nt35597",

You should use - instead of _ in the name for consistency with other drivers.

Thanks,
Thierry

Quoted 13 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +9 -0
+		.of_match_table = truly_nt35597_of_match,
+	},
+	.probe = truly_nt35597_probe,
+	.remove = truly_nt35597_remove,
+};
+module_mipi_dsi_driver(truly_nt35597_driver);
+
+MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#7 lore raw

Hi Thierry

Thanks for the comments.

I will fix these in v9.

Thanks

Abhinav

Quoted 775 lines · Thierry Reding
Quoted 10 lines · Abhinav Kumar

From: "[email protected]" <[email protected]>

Add support for Truly NT35597 panel driver used
in MSM reference platforms.

This panel driver supports both single DSI and dual DSI modes.

However, this patch series adds support only for
dual DSI mode.

Your lines are very short here. It's usually a good idea to keep the subject line short, but there's no need to wrap this early in the rest of the commit message. It's customary to use up to 72 characters.

Quoted 59 lines

Changes in v8:
- Remove video mode config and headers
- Remove unused macros
- Try to avoid multi-lines wherever possible
- Fix comments locations and make it concise
- Fix return points in probe function

---
 drivers/gpu/drm/panel/Kconfig               |   7 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 676 
++++++++++++++++++++++++++++
 3 files changed, 684 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
drivers/gpu/drm/panel/Kconfig +6 -0
index 6020c30..073ffa0 100644
@@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA 

Dual DSI

drivers/gpu/drm/panel/Kconfig +1 -0
+	  Video Mode panel
 endmenu
drivers/gpu/drm/panel/Makefile +0 -0
index 5ccaaa9..80fd19f 100644
@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += 

panel-seiko-43wvf1g.o
obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) +=
panel-sharp-lq101r1sx01.o
obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) +=
panel-sharp-ls043t1le01.o
obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o

drivers/gpu/drm/panel/Makefile +1 -0
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +6 -0
new file mode 100644
index 0000000..c9e09e2
@@ -0,0 +1,676 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/consumer.h>

drivers/gpu/drm/panel/panel-truly-nt35597.c line 16

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/of_device.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>

The headers should be sorted alphabetically.

Quoted 14 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +14 -0
+
+static const char * const regulator_names[] = {
+	"vdda",
+	"vdispp",
+	"vdispn",
+};
+
+static unsigned long const regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000,
+};
+
+static unsigned long const regulator_disable_loads[] = {

drivers/gpu/drm/panel/panel-truly-nt35597.c line 40

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+	80,
+	100,
+	100,
+};
+
+struct nt35597_config {
+	u32 width_mm;
+	u32 height_mm;
+	const char *panel_name;
+	const void *panel_on_cmds;

Why void *? You define the correct data structure a few lines further down, so you might as well just move that definition up and use the proper data structure here. Then there'd be no need to cast this to struct cmd_set * later on when you use it.

Quoted 24 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +23 -0
+	u32 num_on_cmds;
+	const struct drm_display_mode *dm;
+};
+
+struct truly_nt35597 {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *mode_gpio;
+
+	struct backlight_device *backlight;
+
+	struct mipi_dsi_device *dsi[2];
+
+	const struct nt35597_config *config;
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel 

*panel)

drivers/gpu/drm/panel/panel-truly-nt35597.c line 73

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+{
+	return container_of(panel, struct truly_nt35597, panel);
+}
+
+struct cmd_set {
+	u8 commands[4];
+	u8 size;
+};
+
+static struct cmd_set qcom_2k_panel_magic_cmds[] = {

static const?

Quoted 496 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +196 -0
+	/* CMD2_P0 */
+	{ { 0xff, 0x20 }, 2 },
+	{ { 0xfb, 0x01 }, 2 },
+	{ { 0x00, 0x01 }, 2 },
+	{ { 0x01, 0x55 }, 2 },
+	{ { 0x02, 0x45 }, 2 },
+	{ { 0x05, 0x40 }, 2 },
+	{ { 0x06, 0x19 }, 2 },
+	{ { 0x07, 0x1e }, 2 },
+	{ { 0x0b, 0x73 }, 2 },
+	{ { 0x0c, 0x73 }, 2 },
+	{ { 0x0e, 0xb0 }, 2 },
+	{ { 0x0f, 0xae }, 2 },
+	{ { 0x11, 0xb8 }, 2 },
+	{ { 0x13, 0x00 }, 2 },
+	{ { 0x58, 0x80 }, 2 },
+	{ { 0x59, 0x01 }, 2 },
+	{ { 0x5a, 0x00 }, 2 },
+	{ { 0x5b, 0x01 }, 2 },
+	{ { 0x5c, 0x80 }, 2 },
+	{ { 0x5d, 0x81 }, 2 },
+	{ { 0x5e, 0x00 }, 2 },
+	{ { 0x5f, 0x01 }, 2 },
+	{ { 0x72, 0x11 }, 2 },
+	{ { 0x68, 0x03 }, 2 },
+	/* CMD2_P4 */
+	{ { 0xFF, 0x24 }, 2 },
+	{ { 0xFB, 0x01 }, 2 },
+	{ { 0x00, 0x1C }, 2 },
+	{ { 0x01, 0x0B }, 2 },
+	{ { 0x02, 0x0C }, 2 },
+	{ { 0x03, 0x01 }, 2 },
+	{ { 0x04, 0x0F }, 2 },
+	{ { 0x05, 0x10 }, 2 },
+	{ { 0x06, 0x10 }, 2 },
+	{ { 0x07, 0x10 }, 2 },
+	{ { 0x08, 0x89 }, 2 },
+	{ { 0x09, 0x8A }, 2 },
+	{ { 0x0A, 0x13 }, 2 },
+	{ { 0x0B, 0x13 }, 2 },
+	{ { 0x0C, 0x15 }, 2 },
+	{ { 0x0D, 0x15 }, 2 },
+	{ { 0x0E, 0x17 }, 2 },
+	{ { 0x0F, 0x17 }, 2 },
+	{ { 0x10, 0x1C }, 2 },
+	{ { 0x11, 0x0B }, 2 },
+	{ { 0x12, 0x0C }, 2 },
+	{ { 0x13, 0x01 }, 2 },
+	{ { 0x14, 0x0F }, 2 },
+	{ { 0x15, 0x10 }, 2 },
+	{ { 0x16, 0x10 }, 2 },
+	{ { 0x17, 0x10 }, 2 },
+	{ { 0x18, 0x89 }, 2 },
+	{ { 0x19, 0x8A }, 2 },
+	{ { 0x1A, 0x13 }, 2 },
+	{ { 0x1B, 0x13 }, 2 },
+	{ { 0x1C, 0x15 }, 2 },
+	{ { 0x1D, 0x15 }, 2 },
+	{ { 0x1E, 0x17 }, 2 },
+	{ { 0x1F, 0x17 }, 2 },
+	/* STV */
+	{ { 0x20, 0x40 }, 2 },
+	{ { 0x21, 0x01 }, 2 },
+	{ { 0x22, 0x00 }, 2 },
+	{ { 0x23, 0x40 }, 2 },
+	{ { 0x24, 0x40 }, 2 },
+	{ { 0x25, 0x6D }, 2 },
+	{ { 0x26, 0x40 }, 2 },
+	{ { 0x27, 0x40 }, 2 },
+	/* Vend */
+	{ { 0xE0, 0x00 }, 2 },
+	{ { 0xDC, 0x21 }, 2 },
+	{ { 0xDD, 0x22 }, 2 },
+	{ { 0xDE, 0x07 }, 2 },
+	{ { 0xDF, 0x07 }, 2 },
+	{ { 0xE3, 0x6D }, 2 },
+	{ { 0xE1, 0x07 }, 2 },
+	{ { 0xE2, 0x07 }, 2 },
+	/* UD */
+	{ { 0x29, 0xD8 }, 2 },
+	{ { 0x2A, 0x2A }, 2 },
+	/* CLK */
+	{ { 0x4B, 0x03 }, 2 },
+	{ { 0x4C, 0x11 }, 2 },
+	{ { 0x4D, 0x10 }, 2 },
+	{ { 0x4E, 0x01 }, 2 },
+	{ { 0x4F, 0x01 }, 2 },
+	{ { 0x50, 0x10 }, 2 },
+	{ { 0x51, 0x00 }, 2 },
+	{ { 0x52, 0x80 }, 2 },
+	{ { 0x53, 0x00 }, 2 },
+	{ { 0x56, 0x00 }, 2 },
+	{ { 0x54, 0x07 }, 2 },
+	{ { 0x58, 0x07 }, 2 },
+	{ { 0x55, 0x25 }, 2 },
+	/* Reset XDONB */
+	{ { 0x5B, 0x43 }, 2 },
+	{ { 0x5C, 0x00 }, 2 },
+	{ { 0x5F, 0x73 }, 2 },
+	{ { 0x60, 0x73 }, 2 },
+	{ { 0x63, 0x22 }, 2 },
+	{ { 0x64, 0x00 }, 2 },
+	{ { 0x67, 0x08 }, 2 },
+	{ { 0x68, 0x04 }, 2 },
+	/* Resolution:1440x2560 */
+	{ { 0x72, 0x02 }, 2 },
+	/* mux */
+	{ { 0x7A, 0x80 }, 2 },
+	{ { 0x7B, 0x91 }, 2 },
+	{ { 0x7C, 0xD8 }, 2 },
+	{ { 0x7D, 0x60 }, 2 },
+	{ { 0x7F, 0x15 }, 2 },
+	{ { 0x75, 0x15 }, 2 },
+	/* ABOFF */
+	{ { 0xB3, 0xC0 }, 2 },
+	{ { 0xB4, 0x00 }, 2 },
+	{ { 0xB5, 0x00 }, 2 },
+	/* Source EQ */
+	{ { 0x78, 0x00 }, 2 },
+	{ { 0x79, 0x00 }, 2 },
+	{ { 0x80, 0x00 }, 2 },
+	{ { 0x83, 0x00 }, 2 },
+	/* FP BP */
+	{ { 0x93, 0x0A }, 2 },
+	{ { 0x94, 0x0A }, 2 },
+	/* Inversion Type */
+	{ { 0x8A, 0x00 }, 2 },
+	{ { 0x9B, 0xFF }, 2 },
+	/* IMGSWAP =1 @PortSwap=1 */
+	{ { 0x9D, 0xB0 }, 2 },
+	{ { 0x9F, 0x63 }, 2 },
+	{ { 0x98, 0x10 }, 2 },
+	/* FRM */
+	{ { 0xEC, 0x00 }, 2 },
+	/* CMD1 */
+	{ { 0xFF, 0x10 }, 2 },
+	/* VBP+VSA=,VFP = 10H */
+	{ { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
+	/* FTE on */
+	{ { 0x35, 0x00 }, 2 },
+	/* EN_BK =1(auto black) */
+	{ { 0xE5, 0x01 }, 2 },
+	/* CMD mode(10) VDO mode(03) */
+	{ { 0xBB, 0x03 }, 2 },
+	/* Non Reload MTP */
+	{ { 0xFB, 0x01 }, 2 },
+};
+
+static int truly_dcs_write(struct drm_panel *panel, u32 command)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write(ctx->dsi[i], command, NULL, 0);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd 0x%x failed for dsi = %d\n",
+				command, i);
+		}
+	}
+
+	return ret;
+}
+
+static int truly_dcs_write_buf(struct drm_panel *panel,
+	u32 size, u8 *buf)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], buf, size);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"failed to tx cmd [%d], err: %d\n", i, ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int truly_35597_power_on(struct truly_nt35597 *ctx)
+{
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+					regulator_enable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), 

ctx->supplies);

drivers/gpu/drm/panel/panel-truly-nt35597.c new file +35 -0
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Reset sequence of truly panel requires the panel to be
+	 * out of reset for 10ms, followed by being held in reset
+	 * for 10ms and then out again
+	 */
+	gpiod_set_value(ctx->reset_gpio, 0);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	return 0;
+}
+
+static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
+{
+	int ret = 0;
+	int i;
+
+	gpiod_set_value(ctx->reset_gpio, 1);
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+				regulator_disable_loads[i]);
+		if (ret) {
+			DRM_DEV_ERROR(ctx->dev,
+				"regulator_set_load failed %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), 

ctx->supplies);

drivers/gpu/drm/panel/panel-truly-nt35597.c new file +115 -0
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_bulk_disable failed %d\n", ret);
+	}
+	return ret;
+}
+
+static int truly_nt35597_disable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_disable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+				ret);
+	}
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int truly_nt35597_unprepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi[0]->mode_flags = 0;
+	ctx->dsi[1]->mode_flags = 0;
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n", ret);
+	}
+
+	ret = truly_nt35597_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int truly_nt35597_prepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+	int i;
+	struct cmd_set *panel_on_cmds;
+	const struct nt35597_config *config;
+	u32 num_cmds;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = truly_35597_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
+	ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	config = ctx->config;
+	panel_on_cmds = (struct cmd_set *)config->panel_on_cmds;
+	num_cmds = config->num_on_cmds;
+
+	for (i = 0; i < num_cmds; i++) {
+		ret = truly_dcs_write_buf(panel,
+				panel_on_cmds[i].size,
+					panel_on_cmds[i].commands);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd set tx failed i = %d ret = %d\n",
+					i, ret);
+			goto power_off;
+		}
+	}
+
+	ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n", ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending set_display_on DCS command 

*/

drivers/gpu/drm/panel/panel-truly-nt35597.c new file +147 -0
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+
+power_off:
+	if (truly_nt35597_power_off(ctx))
+		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
+	return ret;
+}
+
+static int truly_nt35597_enable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_enable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+						  ret);
+	}
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int truly_nt35597_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	struct drm_display_mode *mode;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = config->width_mm;
+	connector->display_info.height_mm = config->height_mm;
+	drm_mode_copy(mode, config->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
+	.disable = truly_nt35597_disable,
+	.unprepare = truly_nt35597_unprepare,
+	.prepare = truly_nt35597_prepare,
+	.enable = truly_nt35597_enable,
+	.get_modes = truly_nt35597_get_modes,
+};
+
+static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
+{
+	struct device *dev = ctx->dev;
+	int ret, i;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+			PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->mode_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
+			PTR_ERR(ctx->mode_gpio));
+		return PTR_ERR(ctx->mode_gpio);
+	}
+
+	/* dual port */
+	gpiod_set_value(ctx->mode_gpio, 0);
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = dev;
+	ctx->panel.funcs = &truly_nt35597_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	return 0;
+}
+
+static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
+	.name = "1440x2560",
+	.clock = 268316,
+	.hdisplay = 1440,
+	.hsync_start = 1440 + 200,
+	.hsync_end = 1440 + 200 + 32,
+	.htotal = 1440 + 200 + 32 + 64,
+	.vdisplay = 2560,
+	.vsync_start = 2560 + 8,
+	.vsync_end = 2560 + 8 + 1,
+	.vtotal = 2560 + 8 + 1 + 7,
+	.vrefresh = 60,
+	.flags = 0,
+};
+
+static const struct nt35597_config nt35597_dir = {
+	.width_mm = 74,
+	.height_mm = 131,
+	.panel_name = "qcom_sdm845_mtp_2k_panel",
+	.dm = &qcom_sdm845_mtp_2k_mode,
+	.panel_on_cmds = qcom_2k_panel_magic_cmds,
+	.num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
+};
+
+static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct truly_nt35597 *ctx;
+	struct mipi_dsi_device *dsi1_device;
+	struct device_node *dsi1;
+	struct mipi_dsi_host *dsi1_host;
+	struct mipi_dsi_device *dsi_dev;
+	int ret = 0;
+	int i;
+
+	const struct mipi_dsi_device_info info = {
+		.type = "trulynt35597",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+

drivers/gpu/drm/panel/panel-truly-nt35597.c line 576

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+	if (!ctx)
+		return -ENOMEM;
+
+	/*
+	 * This device represents itself as one with
+	 * two input ports which are fed by the output
+	 * ports of the two DSI controllers . The DSI0
+	 * is the master controller and has most of the
+	 * panel related info in its child node.
+	 */

Your comments can be wider. It's typical to wrap at column 78, not earlier.

Quoted 18 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +18 -0
+
+	ctx->config = of_device_get_match_data(dev);
+
+	if (!ctx->config) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+	if (!dsi1) {
+		DRM_DEV_ERROR(dev,
+			"failed to get remote node for dsi1_device\n");
+		return -ENODEV;
+	}
+
+	dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
+	of_node_put(dsi1);
+	if (!dsi1_host) {

drivers/gpu/drm/panel/panel-truly-nt35597.c line 604

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+		DRM_DEV_ERROR(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	/* register the second DSI device */
+	dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
+	if (IS_ERR(dsi1_device)) {
+		DRM_DEV_ERROR(dev, "failed to create dsi device\n");
+		return PTR_ERR(dsi);
+	}

Can you roll in the fix from here:

	https://patchwork.freedesktop.org/patch/245175/
Quoted 14 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +14 -0
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi[0] = dsi;
+	ctx->dsi[1] = dsi1_device;
+
+	ret = truly_nt35597_panel_add(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to add panel\n");
+		goto err_panel_add;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {

drivers/gpu/drm/panel/panel-truly-nt35597.c line 628

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+		dsi_dev = ctx->dsi[i];
+		dsi_dev->lanes = 4;
+		dsi_dev->format = MIPI_DSI_FMT_RGB888;
+		dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+			MIPI_DSI_CLOCK_NON_CONTINUOUS;
+		ret = mipi_dsi_attach(dsi_dev);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dev,
+				"dsi attach failed i = %d\n", i);
+				goto err_dsi_attach;

Indentation is wrong here. The goto should be indented one level less.

Quoted 23 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +23 -0
+		}
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+err_panel_add:
+	mipi_dsi_device_unregister(dsi1_device);
+	return ret;
+}
+
+static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
+{
+	struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi[0])
+		mipi_dsi_detach(ctx->dsi[0]);
+	if (ctx->dsi[1]) {
+		mipi_dsi_detach(ctx->dsi[1]);
+		mipi_dsi_device_unregister(ctx->dsi[1]);
+	}
+

drivers/gpu/drm/panel/panel-truly-nt35597.c line 661

Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +10 -0
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id truly_nt35597_of_match[] = {
+	{	.compatible = "truly,nt35597-2K-display",
+		.data = &nt35597_dir,
+	},
+
+	{ }

The table is weirdly formatted. The ".compatible = ..." line should be an a separate line, and there should be no blank line before { }.

drivers/gpu/drm/panel/panel-truly-nt35597.c line 667

Quoted 6 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +6 -0
+};
+MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
+
+static struct mipi_dsi_driver truly_nt35597_driver = {
+	.driver = {
+		.name = "panel_truly_nt35597",

You should use - instead of _ in the name for consistency with other drivers.

Thanks,
Thierry

Quoted 13 lines
Quoted 10 lines
drivers/gpu/drm/panel/panel-truly-nt35597.c new file +9 -1
+		.of_match_table = truly_nt35597_of_match,
+	},
+	.probe = truly_nt35597_probe,
+	.remove = truly_nt35597_remove,
+};
+module_mipi_dsi_driver(truly_nt35597_driver);
+
+MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");
--
Quoted 3 lines

The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel