Convert Pico-Pi i.MX7D to DM
cover Convert Pico-Pi i.MX7D to DM
Hi all,
Pinctrl, GPIO, I2C, MMC, ETH are converted.
Convert PMIC is the same of warp7 but i have a some erros, si this log :
U-Boot SPL 2019.01-00197-ga524e5d-dirty (Jan 20 2019 - 21:09:49 +0100) Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
Downloading file of size 556397 to 0x877fffc0... done Jumping to header at 0x877fffc0
Header Tag is not an IMX image
U-Boot 2019.01-00197-ga524e5d-dirty (Jan 20 2019 - 21:09:49 +0100)
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 43C Reset cause: POR Model: TechNexion PICO-IMX7D Board and PI baseboard Board: i.MX7D PICOSOM DRAM: 512 MiB read error from device: 9df65458 register: 0x3! PMIC: PFUZE3000 DEV_ID=0x0 REV_ID=0xfffffffb read error from device: 9df65458 register: 0x69! write error to device: 9df65458 register: 0x23! write error to device: 9df65458 register: 0x31! write error to device: 9df65458 register: 0x21! write error to device: 9df65458 register: 0x2f! read error from device: 9df65458 register: 0x2e! write error to device: 9df65458 register: 0x2e! MMC: FSL_SDHC: 2, FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from MMC... OK In: serial at 30a70000 Out: serial at 30a70000 Err: serial at 30a70000
Net:
Warning: ethernet at 30be0000 using MAC address from ROM
eth0: ethernet at 30be0000
Hit any key to stop autoboot: 0
USB is convert but update u-boot with dfu log a error :
=> dfu 0 mmc 0
Request would exceed designated area!
#Deferred dfu_flush() failed!=>
Thanks a advance for your help.
Best Regards,
Joris Offouga
Joris Offouga (9):
Arm: dts: imx7d-pico: Import Linux pico-pi dts
Arm: imx7d-pico: Add DT file hooks
pico-pi-imx7d: defconfig Enable DM gpio pinctrl and pinctrl_imx7
arm: imx7d-pico-pi: Convert to DM MMC initialization
pico-pi-imx7d: defconfig: Switch to DM for I2C
pico-imx7d-pico: defconfig: Switch to DM for UART
pico-imx7d: Convert to DM PMIC
arm: pico-pi-imx7d: Convert to DM USB
pico-imx7d: Convert to DM Ethernet
arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx7d-pico-pi.dts | 102 ++++++ arch/arm/dts/imx7d-pico.dtsi | 588 +++++++++++++++++++++++++++++++ board/technexion/pico-imx7d/pico-imx7d.c | 105 +----- configs/pico-pi-imx7d_defconfig | 17 +- include/configs/pico-imx7d.h | 11 - 6 files changed, 726 insertions(+), 100 deletions(-) create mode 100644 arch/arm/dts/imx7d-pico-pi.dts create mode 100644 arch/arm/dts/imx7d-pico.dtsi
Signature · 1 line
2.7.4
cover Convert Pico-Pi i.MX7D to DM
Quoted 40 lines · On Sun, 20 Jan 2019 23:38:32 +0100 Joris Offouga <[email protected]> wrote:
Hi all,
Pinctrl, GPIO, I2C, MMC, ETH are converted.
Convert PMIC is the same of warp7 but i have a some erros, si this log : U-Boot SPL 2019.01-00197-ga524e5d-dirty (Jan 20 2019 - 21:09:49 +0100) Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
Downloading file of size 556397 to0x877fffc0... done Jumping to header at0x877fffc0
Header Tag is not an IMX imageU-Boot 2019.01-00197-ga524e5d-dirty (Jan 20 2019 - 21:09:49 +0100)
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 43C Reset cause: POR Model: TechNexion PICO-IMX7D Board and PI baseboard Board: i.MX7D PICOSOM DRAM: 512 MiB read error from device: 9df65458 register: 0x3! PMIC: PFUZE3000 DEV_ID=0x0 REV_ID=0xfffffffb read error from device: 9df65458 register: 0x69! write error to device: 9df65458 register: 0x23! write error to device: 9df65458 register: 0x31! write error to device: 9df65458 register: 0x21! write error to device: 9df65458 register: 0x2f! read error from device: 9df65458 register: 0x2e! write error to device: 9df65458 register: 0x2e! MMC: FSL_SDHC: 2, FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from MMC... OK In: serial at 30a70000 Out: serial at 30a70000 Err: serial at 30a70000Net:
Warning: ethernet at30be0000using MAC address from ROM
eth0: ethernet at30be0000
Hit any key to stop autoboot: 0
Quoted 5 lines
USB is convert but update u-boot with dfu log a error :
=> dfu 0 mmc 0
Request would exceed designated area!
#Deferreddfu_flush()failed!=>
Please check if malloc pool size (in Kconfig) is large enough to handle DFU requests.
Otherwise, please #define DEBUG in ./drivers/dfu.c and dfu_mmc.c and share output.
Quoted 25 lines
Thanks a advance for your help.
Best Regards,
Joris Offouga
Joris Offouga (9):
Arm: dts: imx7d-pico: Import Linux pico-pi dts
Arm: imx7d-pico: Add DT file hooks
pico-pi-imx7d: defconfig Enable DM gpio pinctrl andpinctrl_imx7
arm: imx7d-pico-pi: Convert to DM MMC initialization
pico-pi-imx7d: defconfig: Switch to DM for I2C
pico-imx7d-pico: defconfig: Switch to DM for UART
pico-imx7d: Convert to DM PMIC
arm: pico-pi-imx7d: Convert to DM USB
pico-imx7d: Convert to DM Ethernetarch/arm/dts/Makefile | 3 +- arch/arm/dts/imx7d-pico-pi.dts | 102 ++++++ arch/arm/dts/imx7d-pico.dtsi | 588 +++++++++++++++++++++++++++++++ board/technexion/pico-imx7d/pico-imx7d.c | 105 +----- configs/pico-pi-imx7d_defconfig | 17 +- include/configs/pico-imx7d.h | 11 - 6 files changed, 726
Quoted 4 lines
insertions(+), 100 deletions(-) create mode 100644
arch/arm/dts/imx7d-pico-pi.dtscreate mode 100644arch/arm/dts/imx7d-pico.dtsi
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190122/e890ca77/attachment.sig>
cover Convert Pico-Pi i.MX7D to DM
Le 22/01/2019 à 10:47, Lukasz Majewski a écrit :
Quoted 43 lines
Quoted 40 lines · On Sun, 20 Jan 2019 23:38:32 +0100 Joris Offouga <[email protected]> wrote:
Hi all,
Pinctrl, GPIO, I2C, MMC, ETH are converted.
Convert PMIC is the same of warp7 but i have a some erros, si this log : U-Boot SPL 2019.01-00197-ga524e5d-dirty (Jan 20 2019 - 21:09:49 +0100) Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
Downloading file of size 556397 to0x877fffc0... done Jumping to header at0x877fffc0
Header Tag is not an IMX imageU-Boot 2019.01-00197-ga524e5d-dirty (Jan 20 2019 - 21:09:49 +0100)
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 43C Reset cause: POR Model: TechNexion PICO-IMX7D Board and PI baseboard Board: i.MX7D PICOSOM DRAM: 512 MiB read error from device: 9df65458 register: 0x3! PMIC: PFUZE3000 DEV_ID=0x0 REV_ID=0xfffffffb read error from device: 9df65458 register: 0x69! write error to device: 9df65458 register: 0x23! write error to device: 9df65458 register: 0x31! write error to device: 9df65458 register: 0x21! write error to device: 9df65458 register: 0x2f! read error from device: 9df65458 register: 0x2e! write error to device: 9df65458 register: 0x2e! MMC: FSL_SDHC: 2, FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from MMC... OK In: serial at 30a70000 Out: serial at 30a70000 Err: serial at 30a70000Net:
Warning: ethernet at30be0000using MAC address from ROM
eth0: ethernet at30be0000
Hit any key to stop autoboot: 0
Quoted 5 lines
Quoted 5 lines
USB is convert but update u-boot with dfu log a error :
=> dfu 0 mmc 0
Request would exceed designated area!
#Deferreddfu_flush()failed!=>
Hi Lukasz,
Quoted 2 lines
Please check if malloc pool size (in
Kconfig) is large enough to handle DFU requests.
The dfu request is smaller than the size of malloc pool size
Quoted 3 lines
Otherwise, please #define DEBUG in
./drivers/dfu.canddfu_mmc.cand share output.
This is a log when dfu failed :
blk_find_device: if_type=6, devnum=0: usdhc at 30b40000.blk, 6, 2blk_find_device: if_type=6, devnum=0: usdhc at 30b50000.blk, 6, 1blk_find_device: if_type=6, devnum=0: usdhc at 30b60000.blk, 6, 0 Request would exceed designated area!dfu_write_buffer_drain: Write error!
#Deferred dfu_flush() failed!reset_config:
unbind function 'dfu'/9ef6e678g_dnl_unbind: calling usb_gadget_disconnect for controller 'ci_udc'
Best Regards,
Joris Offouga
Quoted 41 lines
Quoted 25 lines
Thanks a advance for your help.
Best Regards,
Joris Offouga
Joris Offouga (9):
Arm: dts: imx7d-pico: Import Linux pico-pi dts
Arm: imx7d-pico: Add DT file hooks
pico-pi-imx7d: defconfig Enable DM gpio pinctrl andpinctrl_imx7
arm: imx7d-pico-pi: Convert to DM MMC initialization
pico-pi-imx7d: defconfig: Switch to DM for I2C
pico-imx7d-pico: defconfig: Switch to DM for UART
pico-imx7d: Convert to DM PMIC
arm: pico-pi-imx7d: Convert to DM USB
pico-imx7d: Convert to DM Ethernetarch/arm/dts/Makefile | 3 +- arch/arm/dts/imx7d-pico-pi.dts | 102 ++++++ arch/arm/dts/imx7d-pico.dtsi | 588 +++++++++++++++++++++++++++++++ board/technexion/pico-imx7d/pico-imx7d.c | 105 +----- configs/pico-pi-imx7d_defconfig | 17 +- include/configs/pico-imx7d.h | 11 - 6 files changed, 726Quoted 4 lines
insertions(+), 100 deletions(-) create mode 100644
arch/arm/dts/imx7d-pico-pi.dtscreate mode 100644arch/arm/dts/imx7d-pico.dtsiBest regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
cover Convert Pico-Pi i.MX7D to DM
Hi Lukasz,
Quoted 11 lines · Joris Offouga
Hi Lukasz,
Quoted 2 lines
Please check if malloc pool size (in
Kconfig) is large enough to handle DFU requests.The dfu request is smaller than the size of malloc pool size
Quoted 3 lines
Otherwise, please #define DEBUG in
./drivers/dfu.canddfu_mmc.cand share output.This is a log when dfu failed :
Quoted 8 lines
blk_find_device: if_type=6, devnum=0: usdhc at 30b40000.blk, 6, 2blk_find_device: if_type=6, devnum=0: usdhc at 30b50000.blk, 6, 1blk_find_device: if_type=6, devnum=0: usdhc at 30b60000.blk, 6, 0 Request would exceed designated area!dfu_write_buffer_drain: Write error!
#Deferreddfu_flush()failed!reset_config:
unbind function 'dfu'/9ef6e678g_dnl_unbind: callingusb_gadget_disconnectfor controller 'ci_udc'
Do you have any idea on this issue, please?
This DFU bug is one of the items that is blocking the DM conversion of this board.
Thanks
cover Convert Pico-Pi i.MX7D to DM
Hi Fabio,
Quoted 20 lines
Hi Lukasz,
Quoted 15 lines · Joris Offouga
Hi Lukasz,
Quoted 2 lines
Please check if malloc pool size (in
Kconfig) is large enough to handle DFU requests.The dfu request is smaller than the size of malloc pool size
Quoted 3 lines
Otherwise, please #define DEBUG in
./drivers/dfu.canddfu_mmc.cand share output.This is a log when dfu failed :
blk_find_device: if_type=6, devnum=0: usdhc at 30b40000.blk, 6, 2blk_find_device: if_type=6, devnum=0: usdhc at 30b50000.blk, 6, 1blk_find_device: if_type=6, devnum=0: usdhc at 30b60000.blk, 6, 0 Request would exceed designated area!
Please carefully check the eMMC partition size (as defined in dfu_alt_info) and the size of sent data.
This error happens when one wants to write bigger file than the reported space on the partition.
Please look at drivers/dfu/dfu_mmc.c Line: 44
Quoted 6 lines
Quoted 5 lines
dfu_write_buffer_drain: Write error!
#Deferreddfu_flush()failed!reset_config:
unbind function 'dfu'/9ef6e678g_dnl_unbind: callingusb_gadget_disconnectfor controller 'ci_udc'
Quoted 6 lines
Do you have any idea on this issue, please?
This DFU bug is one of the items that is blocking the DM conversion of this board.
Thanks
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190215/0019c5f8/attachment.sig>
cover Convert Pico-Pi i.MX7D to DM
Quoted 22 lines · Lukasz Majewski
Hi Fabio,
Quoted 16 lines
Hi Lukasz,
Quoted 11 lines · Joris Offouga
Hi Lukasz,
Quoted 2 lines
Please check if malloc pool size (in
Kconfig) is large enough to handle DFU requests.The dfu request is smaller than the size of malloc pool size
Quoted 3 lines
Otherwise, please #define DEBUG in
./drivers/dfu.canddfu_mmc.cand share output.This is a log when dfu failed :
Quoted 7 lines
Quoted 4 lines
Quoted 4 lines
blk_find_device: if_type=6, devnum=0: usdhc at 30b40000.blk, 6, 2blk_find_device: if_type=6, devnum=0: usdhc at 30b50000.blk, 6, 1blk_find_device: if_type=6, devnum=0: usdhc at 30b60000.blk, 6, 0 Request would exceed designated area!Please carefully check the eMMC partition size (as defined in
dfu_alt_info) and the size of sent data.
Hi Fabio
I followed Lukasz's advice and I increased the size of the U-Boot in the dfu_alt_info and there is no more error. However, once the SPL and U-Boot are changed and the board reboots with the jumper in Boot from emmc, the SPL can not load the U-Boot.
Best Regards
Joris Offouga
Quoted 30 lines
This error happens when one wants to write bigger file than the reported space on the partition.
Please look at
drivers/dfu/dfu_mmc.cLine: 44Quoted 6 lines
Quoted 5 lines
dfu_write_buffer_drain: Write error!
#Deferreddfu_flush()failed!reset_config:
unbind function 'dfu'/9ef6e678g_dnl_unbind: callingusb_gadget_disconnectfor controller 'ci_udc'Quoted 6 lines
Do you have any idea on this issue, please?
This DFU bug is one of the items that is blocking the DM conversion of this board.
Thanks
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
cover Convert Pico-Pi i.MX7D to DM
Hi Joris,
Quoted 3 lines · Offouga Joris
Hi Fabio
I followed Lukasz's advice and I increased the size of the U-Boot in the
dfu_alt_infoand there is no more error. However, once the SPL and U-Boot are changed and the board reboots with the jumper in Boot from emmc, the SPL can not load the U-Boot.
What is the U-Boot size you used in the dfu_alt_info?
What is the error you see in SPL now?
Thanks
cover Convert Pico-Pi i.MX7D to DM
Quoted 5 lines · Fabio Estevam
Hi Joris,
On Sat, Feb 16, 2019 at 9:06 AM Offouga Joris <[email protected]> wrote:
Quoted 7 lines
Quoted 3 lines
Hi Fabio
I followed Lukasz's advice and I increased the size of the U-Boot in the
dfu_alt_infoand there is no more error. However, once the SPL and U-Boot are changed and the board reboots with the jumper in Boot from emmc, the SPL can not load the U-Boot.What is the U-Boot size you used in the
dfu_alt_info?What is the error you see in SPL now?
Also, imx7 is missing the u-boot,dm-spl properties.
Take a look at imx6ul, for example:
git grep u-boot,dm-spl | grep mx6ul
And see if doing the same for mx7 works.
Thanks
cover Convert Pico-Pi i.MX7D to DM
In reply to Fabio EstevamLe 16/02/2019 à 13:17, Fabio Estevam a écrit :
Quoted 8 lines
Hi Joris,
Quoted 3 lines · Offouga Joris
Hi Fabio
I followed Lukasz's advice and I increased the size of the U-Boot in the
dfu_alt_infoand there is no more error. However, once the SPL and U-Boot are changed and the board reboots with the jumper in Boot from emmc, the SPL can not load the U-Boot.What is the U-Boot size you used in the
dfu_alt_info?
"u-boot raw 0x8a 0x1000"
Quoted 2 lines
What is the error you see in SPL now?
See this log :
U-Boot SPL 2019.04-rc1-00142-g7fe4b77-dirty (Feb 15 2019 - 20:11:50 +0100) Trying to boot from MMC1
Quoted 2 lines
Thanks
Thanks
cover Convert Pico-Pi i.MX7D to DM
Quoted 5 lines · Joris Offouga
Quoted 2 lines · Fabio Estevam
Hi Joris,
Quoted 8 lines
Quoted 6 lines · Offouga Joris
Quoted 4 lines
Hi Fabio
I followed Lukasz's advice and I increased the size of the U-Boot in the
dfu_alt_infoand there is no more error. However, once the SPL and U-Boot are changed and the board reboots with the jumper in Boot from emmc, the SPL can not load the U-Boot.What is the U-Boot size you used in the
dfu_alt_info?"u-boot raw
0x8a0x1000"
The original setting was correct:
u-boot-dtb.img needs to be flashed at the position 69kB of the eMMC.
Originally we had:
u-boot raw 0x8a 0x400;
which means: 0x8a = 138 * 0x400 = 138 * 1024 = 138 sectors. Each sector is 512 bytes, so 138*0.5k = 69kB
Could you also try:
u-boot raw 0x45 0x800
Does it make any difference?
cover Convert Pico-Pi i.MX7D to DM
Le 16/02/2019 à 13:46, Fabio Estevam a écrit :
Quoted 19 lines · Joris Offouga
Quoted 11 lines · Fabio Estevam
Quoted 8 lines
Hi Joris,
Quoted 3 lines · Offouga Joris
Hi Fabio
I followed Lukasz's advice and I increased the size of the U-Boot in the
dfu_alt_infoand there is no more error. However, once the SPL and U-Boot are changed and the board reboots with the jumper in Boot from emmc, the SPL can not load the U-Boot.What is the U-Boot size you used in the
dfu_alt_info?"u-boot raw
0x8a0x1000"The original setting was correct:
u-boot-dtb.img needs to be flashed at the position 69kB of the eMMC.Originally we had:
u-boot raw
0x8a0x400;
Quoted 8 lines
which means:
0x8a= 138 *0x400= 138 * 1024 = 138 sectors. Each sector is 512 bytes, so 138*0.5k = 69kBCould you also try:
u-boot raw
0x450x800Does it make any difference?
Yes , download with dfu it's okay but after rebooting the SPL does not load.
For u-boot, dm-spl, this does not work only if the SPL is converted to DM too, because the add-on in the uscdh3 node did not change the problem of loading the U-Boot
cover Convert Pico-Pi i.MX7D to DM
Quoted 2 lines · Joris Offouga
Yes , download with dfu it's okay but after rebooting the SPL does not load.
Does it boot if you flash SPL and u-boot-dtb.img via "ums 0 mmc 0" command?
cover Convert Pico-Pi i.MX7D to DM
Le 16/02/2019 à 14:58, Fabio Estevam a écrit :
Quoted 5 lines · Joris Offouga
Quoted 3 lines
Yes , download with dfu it's okay but after rebooting the SPL does not load.
Does it boot if you flash SPL and u-boot-dtb.img via "ums 0 mmc 0" command?
By doing this the SPL still does not find the U-Boot binary always this same log:
U-Boot SPL 2019.04-rc1-00142-g7fe4b77-dirty (Feb 16 2019 - 13:58:30
+0100)
Trying to boot from MMC1
cover Convert Pico-Pi i.MX7D to DM
Hi Joris,
Quoted 6 lines · Joris Offouga
By doing this the SPL still does not find the U-Boot binary always this same log:
U-Boot SPL 2019.04-rc1-00142-g7fe4b77-dirty (Feb 16 2019 - 13:58:30+0100)
Trying to boot from MMC1
Yes, just tried it and I saw the same here.
I started from scratch and used top of tree U-Boot.
When I load it via USB I see a hang:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 50C Reset cause: POR Board: i.MX7D PICOSOM I2C: ready DRAM: 512 MiB
...
So this is a regression and I will try to bisect it.
cover Convert Pico-Pi i.MX7D to DM
Le 16/02/2019 à 15:42, Fabio Estevam a écrit :
Quoted 1 line
Hi Joris,
Hi Fabio,
Quoted 21 lines · Joris Offouga
Quoted 7 lines
By doing this the SPL still does not find the U-Boot binary always this same log:
U-Boot SPL 2019.04-rc1-00142-g7fe4b77-dirty (Feb 16 2019 - 13:58:30+0100)
Trying to boot from MMC1Yes, just tried it and I saw the same here.
I started from scratch and used top of tree U-Boot.
When I load it via USB I see a hang:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 50C Reset cause: POR Board: i.MX7D PICOSOM I2C: ready DRAM: 512 MiB
Quoted 3 lines
...
So this is a regression and I will try to bisect it.
Ok, thanks for your help :).
I worked new commits do you want me to update the RFC in v2?
Best Regards,
Joris
cover Convert Pico-Pi i.MX7D to DM
Quoted 3 lines · Joris Offouga
Ok, thanks for your help :).
I worked new commits do you want me to update the RFC in v2?
Please generate your series against the latest u-boot-imx tree.
However, I observed the hang when I use the latest u-boot or u-boot-imx tree, so we will need to fix the hang problem first.
Thanks
cover Convert Pico-Pi i.MX7D to DM
Le 16/02/2019 à 15:54, Fabio Estevam a écrit :
Quoted 9 lines · Joris Offouga
Quoted 4 lines
Ok, thanks for your help :).
I worked new commits do you want me to update the RFC in v2?
Please generate your series against the latest u-boot-imx tree.
However, I observed the hang when I use the latest u-boot or u-boot-imx tree, so we will need to fix the hang problem first.
Actually on the top of u-boot-imx there is a blocking when loading u-boot-dtb.img with imx_usb_loader.
I show you my log:
U-Boot SPL 2019.04-rc1-dirty (Feb 16 2019 - 16:10:56 +0100) Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
Downloading file of size 530520 to 0x877fffc0... done Jumping to header at 0x877fffc0
Header Tag is not an IMX image
I will send the series with the status rfc and not patch you are from okay ?
Thanks
Quoted 2 lines
Thanks
cover Convert Pico-Pi i.MX7D to DM
Quoted 1 line · Joris Offouga
Actually on the top of u-boot-imx there is a blocking when loading u-boot-dtb.img with
imx_usb_loader.
Just run a "git bisect" and the problem comes from:
commit 9e3c0174da842dd88f5feaffbf843ba332233897 (refs/bisect/bad)
Author: Fabio Estevam <[email protected]> Date: Tue Dec 11 16:40:38 2018 -0200
pico-imx7d: Add LCD support
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface.
It used to work at some point as I could see the splashscreen logo in the screen.
Please revert it from your tree and see if it works for you.
I will need to investigate why my commit broke the boot, but for now just revert it locally so that you can continue the DM conversion.
Thanks
cover Convert Pico-Pi i.MX7D to DM
Le 16/02/2019 à 16:25, Fabio Estevam a écrit :
Quoted 17 lines · Joris Offouga
Quoted 2 lines
Actually on the top of u-boot-imx there is a blocking when loading u-boot-dtb.img with
imx_usb_loader.Just run a "git bisect" and the problem comes from:
commit
9e3c0174da842dd88f5feaffbf843ba332233897(refs/bisect/bad)Author: Fabio Estevam <[email protected]> Date: Tue Dec 11 16:40:38 2018 -0200pico-imx7d: Add LCD support
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface.
Signed-off-by Fabio Estevam <[email protected]>Signed-off-by Otavio Salvador <[email protected]>
Quoted 7 lines
It used to work at some point as I could see the splashscreen logo in the screen.
Please revert it from your tree and see if it works for you.
I will need to investigate why my commit broke the boot, but for now just revert it locally so that you can continue the DM conversion.
I reversed your commit but the block is still there, but even with
your commit on the top of the u-boot master.
I don't have the block with imx_usb_loader just when I try to boot from the emmc
Quoted 2 lines
Thanks
cover Convert Pico-Pi i.MX7D to DM
Quoted 6 lines · Joris Offouga
I reversed your commit but the block is still there, but even with
your commit on the top of the u-boot master.
I don't have the block with
imx_usb_loaderjust when I try to boot from the emmc
Ops, it seems we have different issues going on.
I think you would need to run "git bisect" to find out what breaks your boot case.
cover Convert Pico-Pi i.MX7D to DM
Quoted 13 lines · Fabio Estevam
Quoted 9 lines · Joris Offouga
I reversed your commit but the block is still there, but even with
your commit on the top of the u-boot master.
I don't have the block with
imx_usb_loaderjust when I try to boot from the emmcOps, it seems we have different issues going on.
Hi Fabio,
Have you been able to solve your bug? I think that the coming must come from yours and that with the conversion dm that I have in local it must persist
Best Regards
Joris
Quoted 3 lines
I think you would need to run "git bisect" to find out what breaks your boot case.
cover Convert Pico-Pi i.MX7D to DM
Hi Joris,
Quoted 2 lines · Offouga Joris
Hi Fabio,
Have you been able to solve your bug? I think that the coming must come from yours and that with the conversion dm that I have in local it must persist
Unfortunately, I haven't had a chance to debug this further.
If you make progress, please let us know.
Regards,
Fabio Estevam
cover Convert Pico-Pi i.MX7D to DM
In reply to Fabio EstevamHi Joris,
Quoted 8 lines · Fabio Estevam
Just run a "git bisect" and the problem comes from:
commit
9e3c0174da842dd88f5feaffbf843ba332233897(refs/bisect/bad)Author: Fabio Estevam <[email protected]> Date: Tue Dec 11 16:40:38 2018 -0200pico-imx7d: Add LCD support
Quoted 8 lines
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface.
Signed-off-by Fabio Estevam <[email protected]>Signed-off-by Otavio Salvador <[email protected]>It used to work at some point as I could see the splashscreen logo in the screen.
Just a quick update: if I boot from eMMC I don't see this video related hang. I only see the hang when I boot from USB.
cover Convert Pico-Pi i.MX7D to DM
Quoted 19 lines · Fabio Estevam
Hi Joris,
Quoted 13 lines · Fabio Estevam
Just run a "git bisect" and the problem comes from:
commit
9e3c0174da842dd88f5feaffbf843ba332233897(refs/bisect/bad)Author: Fabio Estevam <[email protected]> Date: Tue Dec 11 16:40:38 2018 -0200pico-imx7d: Add LCD support
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface.
Quoted 8 lines
Quoted 5 lines
Signed-off-by Fabio Estevam <[email protected]>Signed-off-by Otavio Salvador <[email protected]>It used to work at some point as I could see the splashscreen logo in the screen.
Just a quick update: if I boot from eMMC I don't see this video related hang. I only see the hang when I boot from USB.
I do not have the screen connected when I do my tests and I disabled CONFIG_VIDEO because it lacks the GPIOs for the screen in the current device tree
cover Convert Pico-Pi i.MX7D to DM
Quoted 26 lines · Offouga Joris
Quoted 23 lines · Fabio Estevam
Hi Joris,
Quoted 16 lines · Fabio Estevam
Just run a "git bisect" and the problem comes from:
commit
9e3c0174da842dd88f5feaffbf843ba332233897(refs/bisect/bad)Author: Fabio Estevam <[email protected]> Date: Tue Dec 11 16:40:38 2018 -0200pico-imx7d: Add LCD support
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface.
Signed-off-by Fabio Estevam <[email protected]>Signed-off-by Otavio Salvador <[email protected]>
Quoted 6 lines
Quoted 5 lines
Quoted 2 lines
It used to work at some point as I could see the splashscreen logo in the screen.
Just a quick update: if I boot from eMMC I don't see this video related hang. I only see the hang when I boot from USB.
I do not have the screen connected when I do my tests and I disabled
CONFIG_VIDEObecause it lacks the GPIOs for the screen in the current device tree
Hi Fabio,
I revert the commit about add lcd and on u-boot master and u-boot imx i have the u-boot is flashed correctly in usb and dfu.
do you agree that I send the revert of the commit?
Best Regards,
Joris
cover Convert Pico-Pi i.MX7D to DM
Hi Joris,
Quoted 5 lines · Offouga Joris
Hi Fabio,
I revert the commit about add lcd and on u-boot master and u-boot imx i have the u-boot is flashed correctly in usb and dfu.
do you agree that I send the revert of the commit?
Yes, please revert it for now and resubmit your series that converts pico mx7 to DM.
So the only issue now is the I2C errors?
Thanks,
Fabio Estevam
cover Convert Pico-Pi i.MX7D to DM
Le 10/03/2019 à 15:24, Fabio Estevam a écrit :
Quoted 11 lines
Hi Joris,
Quoted 5 lines · Offouga Joris
Hi Fabio,
I revert the commit about add lcd and on u-boot master and u-boot imx i have the u-boot is flashed correctly in usb and dfu.
do you agree that I send the revert of the commit?
Yes, please revert it for now and resubmit your series that converts pico mx7 to DM.
Ok, i send revert add lcd
Quoted 2 lines
So the only issue now is the I2C errors?
No, I have not solved the problem of the spl that can not find the u-boot-dtb.img in the emmc.
I think the problem comes from the dfu_alt_info we already talked about it but the solution with raw u-boot 0x45 800 does not work do you have another idea?
Thanks,
Joris Offouga
Quoted 4 lines
Thanks,
Fabio Estevam