usb: xhci: Add Clear_TT_Buffer
Subsystems (2)
v9 cover usb: xhci: Add Clear_TT_Buffer
USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt processing for full-/low-speed endpoints connected via a TT, the host software must use the Clear_TT_Buffer request to the TT to ensure that the buffer is not in the busy state".
In our case, a full-speed speaker (ConferenceCam) is behind a high- speed hub (ConferenceCam Connect), sometimes once we get STALL on a request we may continue to get STALL with the folllowing requests, like Set_Interface.
Solution is to invoke usb_hub_clear_tt_buffer() to send Clear_TT_Buffer request to the hub of the device for the following Set_Interface requests to the device to get ACK successfully.
The Clear_TT_Buffer request sent to the hub includes the address of the LS/FS child device in wValue field. usb_hub_clear_tt_buffer() uses udev->devnum to set the address wValue. This won't work for devices connected to xHC.
For other host controllers udev->devnum is the same as the address of the usb device, chosen and set by usb core. With xHC the controller hardware assigns the address, and won't be the same as devnum.
Here we have two patches.
One is to add devaddr in struct usb_device for usb_hub_clear_tt_buffer() to use.
Another is to update devaddr in XHCI address_device callback function and invoke usb_hub_clear_tt_buffer() for halt processing.
Jim Lin (2):
usb: hub : Add devaddr in struct usb_device
usb: xhci: Add Clear_TT_Buffer
drivers/usb/core/hub.c | 4 +++- drivers/usb/host/xhci-ring.c | 12 ++++++++++++ drivers/usb/host/xhci.c | 1 + include/linux/usb.h | 2 ++ 4 files changed, 18 insertions(+), 1 deletion(-)
Signature · 1 line
2.1.4
PATCH v9 1/2 usb: hub : Add devaddr in struct usb_device
The Clear_TT_Buffer request sent to the hub includes the address of the LS/FS child device in wValue field. usb_hub_clear_tt_buffer() uses udev->devnum to set the address wValue. This won't work for devices connected to xHC.
For other host controllers udev->devnum is the same as the address of the usb device, chosen and set by usb core. With xHC the controller hardware assigns the address, and won't be the same as devnum.
Here we add devaddr in "struct usb_device" forusb_hub_clear_tt_buffer() to use.
---
v2: xhci_clear_tt_buffer_complete: add static, shorter indentation
, remove its claiming in xhci.h
v3: Add description for clearing_tt (xhci.h)
v4: Remove clearing_tt flag because hub_tt_work has hub->tt.lock
to protect for Clear_TT_Buffer to be run serially. Remove xhci_clear_tt_buffer_complete as it's not necessary. Same reason as the above.
Extend usb_hub_clear_tt_buffer parameter
v5: Not extending usb_hub_clear_tt_buffer parameter
Add description.
v6: Remove unused parameter slot_id from xhci_clear_hub_tt_buffer
v7: Add devaddr field in "struct usb_device"
v8: split as two patches, change type from int to u8 for devaddr.
v9: Use pahole to find place to put devaddr in struct usb_device.
Remove space between type cast and variable.
hub.c changed from v8
clear->devinfo |= (u16) (udev->devaddr << 4);
to
clear->devinfo |= ((u16)udev->devaddr) << 4;
to solve a problem if devaddr is larger than 16.
drivers/usb/core/hub.c | 4 +++- include/linux/usb.h | 2 ++ 2 files changed, 5 insertions(+), 1 deletion(-)
drivers/usb/core/hub.c +3 -1
@@ -873,7 +873,7 @@ int usb_hub_clear_tt_buffer(struct urb *urb)/* info that CLEAR_TT_BUFFER needs */ clear->tt = tt->multi ? udev->ttport :1 ; clear->devinfo =usb_pipeendpoint (pipe); - clear->devinfo |= udev->devnum <<4 ; + clear->devinfo |= ((u16 )udev->devaddr) <<4 ; clear->devinfo |=usb_pipecontrol (pipe) ? (USB_ENDPOINT_XFER_CONTROL <<11 ) : (USB_ENDPOINT_XFER_BULK <<11 );
@@ -2125,6 +2125,8 @@ static void update_devnum(struct usb_device *udev, int devnum)/* The address for a WUSB device is managed by wusbcore. */ if (!udev->wusb) udev->devnum = devnum; +if (!udev->devaddr) + udev->devaddr = (u8 )devnum; }static void hub_free_dev (struct usb_device *udev)
include/linux/usb.h +2 -0
@@ -566,6 +566,7 @@ struct usb3_lpm_parameters {* @tt: Transaction Translator info; used with low/full speed dev, highspeed hub * @ttport: device port on that tt hub * @toggle: one bit for each endpoint, with ([0] = IN, [1] = OUT) endpoints +* @devaddr: device address, XHCI: assigned by HW, others: same as devnum * @parent: our hub, unless we're the root * @bus: bus we're part of * @ep0: endpoint 0 data (default control pipe)
@@ -643,6 +644,7 @@ struct usb_device {int ttport;unsigned int toggle[2 ]; +u8 devaddr;struct usb_device *parent;struct usb_bus *bus;
Signature · 1 line
2.1.4
Re: [PATCH v9 1/2] usb: hub : Add devaddr in struct usb_device
Quoted 54 lines · Jim Lin
The
Clear_TT_Bufferrequest sent to the hub includes the address of the LS/FS child device in wValue field.usb_hub_clear_tt_buffer()usesudev->devnumto set the address wValue. This won't work for devices connected to xHC.For other host controllers
udev->devnumis the same as the address of the usb device, chosen and set by usb core. With xHC the controller hardware assigns the address, and won't be the same as devnum.Here we add devaddr in "struct
usb_device" forusb_hub_clear_tt_buffer()to use.Signed-off-by Jim Lin <[email protected]>---
v2:xhci_clear_tt_buffer_complete: add static, shorter indentation
, remove its claiming inxhci.h
v3: Add description forclearing_tt(xhci.h)
v4: Removeclearing_ttflag becausehub_tt_workhashub->tt.lock
to protect forClear_TT_Bufferto be run serially. Removexhci_clear_tt_buffer_completeas it's not necessary. Same reason as the above.
Extendusb_hub_clear_tt_bufferparameter
v5: Not extendingusb_hub_clear_tt_bufferparameter
Add description.
v6: Remove unused parameterslot_idfromxhci_clear_hub_tt_buffer
v7: Add devaddr field in "structusb_device"
v8: split as two patches, change type from int to u8 for devaddr.
v9: Use pahole to find place to put devaddr in structusb_device.
Remove space between type cast and variable.
hub.cchanged from v8
clear->devinfo|= (u16) (udev->devaddr<< 4);
to
clear->devinfo|= ((u16)udev->devaddr) << 4;
to solve a problem if devaddr is larger than 16.drivers/usb/core/hub.c | 4 +++- include/linux/usb.h | 2 ++ 2 files changed, 5 insertions(+), 1 deletion(-)drivers/usb/core/hub.c +1
-1@@ -873,7 +873,7 @@ int usb_hub_clear_tt_buffer(struct urb *urb)/* info that CLEAR_TT_BUFFER needs */ clear->tt = tt->multi ? udev->ttport :1 ; clear->devinfo =usb_pipeendpoint (pipe); - clear->devinfo |= udev->devnum <<4 ; + clear->devinfo |= ((u16 )udev->devaddr) <<4 ; clear->devinfo |=usb_pipecontrol (pipe) ? (USB_ENDPOINT_XFER_CONTROL <<11 ) : (USB_ENDPOINT_XFER_BULK <<11 );
drivers/usb/core/hub.c static void update_devnum(struct usb_device *udev, int devnum) · line 2129
Quoted 5 lines
drivers/usb/core/hub.c +2
-0@@ -2125,6 +2125,8 @@ static void update_devnum(struct usb_device *udev, int devnum)/* The address for a WUSB device is managed by wusbcore. */ if (!udev->wusb) udev->devnum = devnum; +if (!udev->devaddr) + udev->devaddr = (u8 )devnum;
Whether or not to put a space after the ')' in a typecast is a matter of personal choice; CodingStyle doesn't say anything about it. Quite often the space is present. IIRC, that is how K&R does it. But it doesn't really matter.
Quoted 16 lines
drivers/usb/core/hub.c +0
-0}static void hub_free_dev (struct usb_device *udev)include/linux/usb.h +1
-0@@ -566,6 +566,7 @@ struct usb3_lpm_parameters {* @tt: Transaction Translator info; used with low/full speed dev, highspeed hub * @ttport: device port on that tt hub * @toggle: one bit for each endpoint, with ([0] = IN, [1] = OUT) endpoints +* @devaddr: device address, XHCI: assigned by HW, others: same as devnum * @parent: our hub, unless we're the root * @bus: bus we're part of * @ep0: endpoint 0 data (default control pipe)
include/linux/usb.h struct usb_device { · line 647
Quoted 4 lines
include/linux/usb.h +1
-0@@ -643,6 +644,7 @@ struct usb_device {int ttport;unsigned int toggle[2 ]; +u8 devaddr;
This is another lousy place to put the new value. A much better position would be immediately after "u8 level".
include/linux/usb.h struct usb_device { · line 650
Quoted 2 lines
include/linux/usb.h +0
-0struct usb_device *parent;struct usb_bus *bus;
You should move into this patch the code added to xhci.c to assign udev->devaddr. Without it, this patch is incomplete: devaddr will not contain the correct value for devices on a USB-3 bus. And it doesn't belong in the 2/2 patch -- that patch is all about making xhci-hcd call usb_clear_tt_buffer().
Alan Stern
PATCH v9 2/2 usb: xhci: Add Clear_TT_Buffer
In reply to Jim LinUSB 2.0 specification chapter 11.17.5 says "as part of endpoint halt processing for full-/low-speed endpoints connected via a TT, the host software must use the Clear_TT_Buffer request to the TT to ensure that the buffer is not in the busy state".
In our case, a full-speed speaker (ConferenceCam) is behind a high- speed hub (ConferenceCam Connect), sometimes once we get STALL on a request we may continue to get STALL with the folllowing requests, like Set_Interface.
Here we update udev->devaddr in address_device callback function (this USB device address is assigned by XHCI controller) and invoke usb_hub_clear_tt_buffer() to send Clear_TT_Buffer request to the hub of the device for the following Set_Interface requests to the device to get ACK successfully.
---
v2: xhci_clear_tt_buffer_complete: add static, shorter indentation
, remove its claiming in xhci.h
v3: Add description for clearing_tt (xhci.h)
v4: Remove clearing_tt flag because hub_tt_work has hub->tt.lock
to protect for Clear_TT_Buffer to be run serially. Remove xhci_clear_tt_buffer_complete as it's not necessary. Same reason as the above.
Extend usb_hub_clear_tt_buffer parameter
v5: Not extending usb_hub_clear_tt_buffer parameter
Add description.
v6: Remove unused parameter slot_id from xhci_clear_hub_tt_buffer
v7: Add devaddr field in "struct usb_device"
v8: split as two patches
v9: no change
drivers/usb/host/xhci-ring.c | 12 ++++++++++++ drivers/usb/host/xhci.c | 1 + 2 files changed, 13 insertions(+)
drivers/usb/host/xhci-ring.c +12 -0
@@ -1786,6 +1786,17 @@ struct xhci_segment *trb_in_td(struct xhci_hcd *xhci,return NULL ; } +static void xhci_clear_hub_tt_buffer (struct xhci_hcd *xhci,struct xhci_td *td) +{ +/* +* As part of low/full-speed endpoint-halt processing +* we must clear the TT buffer (USB 2.0 specification 11.17.5). +*/ +if (td->urb->dev->tt && !usb_pipeint (td->urb->pipe) && + (td->urb->dev->tt->hub !=xhci_to_hcd (xhci)->self.root_hub)) +usb_hub_clear_tt_buffer (td->urb); +} + static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci, unsigned int slot_id, unsigned int ep_index, unsigned int stream_id, struct xhci_td *td,
@@ -1804,6 +1815,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,if (reset_type ==EP_HARD_RESET ) { ep->ep_state |=EP_HARD_CLEAR_TOGGLE ;xhci_cleanup_stalled_ring (xhci, ep_index, stream_id, td); +xhci_clear_hub_tt_buffer (xhci, td); }xhci_ring_cmd_db (xhci); }
drivers/usb/host/xhci.c +1 -0
@@ -4096,6 +4096,7 @@ static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev,/* Zero the input context control for later use */ ctrl_ctx->add_flags =0 ; ctrl_ctx->drop_flags =0 ; + udev->devaddr = (u8)(le32_to_cpu (slot_ctx->dev_state) &DEV_ADDR_MASK ); xhci_dbg_trace(xhci, trace_xhci_dbg_address, "Internal device address = %d",
Signature · 1 line
2.1.4
Quoted 60 lines · Jim Lin
USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt processing for full-/low-speed endpoints connected via a TT, the host software must use the
Clear_TT_Bufferrequest to the TT to ensure that the buffer is not in the busy state".In our case, a full-speed speaker (ConferenceCam) is behind a high- speed hub (ConferenceCam Connect), sometimes once we get STALL on a request we may continue to get STALL with the folllowing requests, like
Set_Interface.Here we update
udev->devaddrinaddress_devicecallback function (this USB device address is assigned by XHCI controller) and invokeusb_hub_clear_tt_buffer()to sendClear_TT_Bufferrequest to the hub of the device for the followingSet_Interfacerequests to the device to get ACK successfully.Signed-off-by Jim Lin <[email protected]>---
v2:xhci_clear_tt_buffer_complete: add static, shorter indentation
, remove its claiming inxhci.h
v3: Add description forclearing_tt(xhci.h)
v4: Removeclearing_ttflag becausehub_tt_workhashub->tt.lock
to protect forClear_TT_Bufferto be run serially. Removexhci_clear_tt_buffer_completeas it's not necessary. Same reason as the above.
Extendusb_hub_clear_tt_bufferparameter
v5: Not extendingusb_hub_clear_tt_bufferparameter
Add description.
v6: Remove unused parameterslot_idfromxhci_clear_hub_tt_buffer
v7: Add devaddr field in "structusb_device"
v8: split as two patches
v9: no changedrivers/usb/host/xhci-ring.c | 12 ++++++++++++ drivers/usb/host/xhci.c | 1 + 2 files changed, 13 insertions(+)drivers/usb/host/xhci-ring.c +11
-0@@ -1786,6 +1786,17 @@ struct xhci_segment *trb_in_td(struct xhci_hcd *xhci,return NULL ; } +static void xhci_clear_hub_tt_buffer (struct xhci_hcd *xhci,struct xhci_td *td) +{ +/* +* As part of low/full-speed endpoint-halt processing +* we must clear the TT buffer (USB 2.0 specification 11.17.5). +*/ +if (td->urb->dev->tt && !usb_pipeint (td->urb->pipe) && + (td->urb->dev->tt->hub !=xhci_to_hcd (xhci)->self.root_hub)) +usb_hub_clear_tt_buffer (td->urb); +} + static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci, unsigned int slot_id, unsigned int ep_index, unsigned int stream_id, struct xhci_td *td,
drivers/usb/host/xhci-ring.c static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci, · line 1821
Quoted 7 lines
drivers/usb/host/xhci-ring.c +1
-0@@ -1804,6 +1815,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,if (reset_type ==EP_HARD_RESET ) { ep->ep_state |=EP_HARD_CLEAR_TOGGLE ;xhci_cleanup_stalled_ring (xhci, ep_index, stream_id, td); +xhci_clear_hub_tt_buffer (xhci, td); }xhci_ring_cmd_db (xhci); }
How come there's no clear_tt_buffer_complete() callback? Without it, xhci-hcd won't know when the TT buffer has been cleared, and so it won't know when to restart the endpoint ring for the halted endpoint.
Note: Restarting the endpoint ring before the TT buffer has been cleared is not safe.
Alan Stern
Quoted 13 lines
drivers/usb/host/xhci.c +1
-0@@ -4096,6 +4096,7 @@ static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev,/* Zero the input context control for later use */ ctrl_ctx->add_flags =0 ; ctrl_ctx->drop_flags =0 ; + udev->devaddr = (u8)(le32_to_cpu (slot_ctx->dev_state) &DEV_ADDR_MASK ); xhci_dbg_trace(xhci, trace_xhci_dbg_address, "Internal device address = %d",