Skip to contentSkip to conversation

Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v2.

PATCH Superseded Zhou Yanjie 2 participants 7 messages Nov 23, 2019 – Nov 24, 2019

Subsystems (3)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v1->v2:
Rebase on top of mips-next, use ingenic-timer driver for system timer and clocksource.

#1 lore raw

PATCH v2 1/4 MIPS: Ingenic: initial X1000 support.

Support the Ingenic X1000 SoC using the code under arch/mips/jz4740. This is left unselectable in Kconfig until a X1000 based board is added in a later commit.

---

Notes:
v1->v2:
Rebase on top of mips-next, use ingenic-timer driver for system timer and clocksource.

 arch/mips/boot/dts/ingenic/x1000.dtsi | 183 ++++++++++++++++++++++++++++++++++
 arch/mips/jz4740/Kconfig              |   6 ++
 2 files changed, 189 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
arch/mips/boot/dts/ingenic/x1000.dtsi new file +183 -0
new file mode 100644
index 00000000..02a9b2a
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1000", "ingenic,x1000e";
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1000-cgu@10000000 {
+		compatible = "ingenic,x1000-cgu";
+		reg = <0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+	};
+
+	apb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <>;
+
+		tcu: timer@10002000 {
+			compatible = "ingenic,x1000-tcu",
+					 "ingenic,jz4770-tcu",
+					 "simple-mfd";
+			reg = <0x10002000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x10002000 0x1000>;
+
+			#clock-cells = <1>;
+
+			clocks = <&cgu X1000_CLK_RTCLK
+				  &cgu X1000_CLK_EXCLK
+				  &cgu X1000_CLK_PCLK>;
+			clock-names = "rtc", "ext", "pclk";
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <27 26 25>;
+		};
+
+		uart0: serial@10030000 {
+			compatible = "ingenic,x1000-uart";
+			reg = <0x10030000 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <51>;
+
+			clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+			clock-names = "baud", "module";
+
+			status = "disabled";
+		};
+
+		uart1: serial@10031000 {
+			compatible = "ingenic,x1000-uart";
+			reg = <0x10031000 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <50>;
+
+			clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+			clock-names = "baud", "module";
+
+			status = "disabled";
+		};
+
+		uart2: serial@10032000 {
+			compatible = "ingenic,x1000-uart";
+			reg = <0x10032000 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <49>;
+
+			clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+			clock-names = "baud", "module";
+
+			status = "disabled";
+		};
+
+		pinctrl: pin-controller@10010000 {
+			compatible = "ingenic,x1000-pinctrl";
+			reg = <0x10010000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpa: gpio@0 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <0>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 0 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <17>;
+			};
+
+			gpb: gpio@1 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <1>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 32 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <16>;
+			};
+
+			gpc: gpio@2 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <2>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 64 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <15>;
+			};
+
+			gpd: gpio@3 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <3>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 96 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <14>;
+			};
+		};
+	};
+};
arch/mips/jz4740/Kconfig +6 -0
index 4dd0c44..6b96844 100644
@@ -33,3 +33,9 @@ config MACH_JZ4780
 	select MIPS_CPU_SCACHE
 	select SYS_HAS_CPU_MIPS32_R2
 	select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
Signature · 1 line
2.7.4
maintainer
#2 lore raw

Re: [PATCH v2 1/4] MIPS: Ingenic: initial X1000 support.

Hi Zhou,

Quoted 66 lines · Zhou Yanjie

Support the Ingenic X1000 SoC using the code under arch/mips/jz4740. This is left unselectable in Kconfig until a X1000 based board is added in a later commit.

---

Notes:
v1->v2:
Rebase on top of mips-next, use ingenic-timer driver for system timer and clocksource.

 arch/mips/boot/dts/ingenic/x1000.dtsi | 183 
++++++++++++++++++++++++++++++++++
 arch/mips/jz4740/Kconfig              |   6 ++
 2 files changed, 189 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
arch/mips/boot/dts/ingenic/x1000.dtsi new file +42 -0
new file mode 100644
index 00000000..02a9b2a
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1000", "ingenic,x1000e";
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1000-cgu@10000000 {
+		compatible = "ingenic,x1000-cgu";
+		reg = <0x10000000 0x100>;
+
+		#clock-cells = <1>;

arch/mips/boot/dts/ingenic/x1000.dtsi line 52

Quoted 10 lines
arch/mips/boot/dts/ingenic/x1000.dtsi new file +10 -0
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+	};
+
+	apb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <>;

You can drop the 'apb' node and list the children in the top node directly. That's what we do in the devicetree for the other Ingenic SoCs.

Cheers,
-Paul

Quoted 149 lines
arch/mips/boot/dts/ingenic/x1000.dtsi new file +131 -0
+
+		tcu: timer@10002000 {
+			compatible = "ingenic,x1000-tcu",
+					 "ingenic,jz4770-tcu",
+					 "simple-mfd";
+			reg = <0x10002000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x10002000 0x1000>;
+
+			#clock-cells = <1>;
+
+			clocks = <&cgu X1000_CLK_RTCLK
+				  &cgu X1000_CLK_EXCLK
+				  &cgu X1000_CLK_PCLK>;
+			clock-names = "rtc", "ext", "pclk";
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <27 26 25>;
+		};
+
+		uart0: serial@10030000 {
+			compatible = "ingenic,x1000-uart";
+			reg = <0x10030000 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <51>;
+
+			clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+			clock-names = "baud", "module";
+
+			status = "disabled";
+		};
+
+		uart1: serial@10031000 {
+			compatible = "ingenic,x1000-uart";
+			reg = <0x10031000 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <50>;
+
+			clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+			clock-names = "baud", "module";
+
+			status = "disabled";
+		};
+
+		uart2: serial@10032000 {
+			compatible = "ingenic,x1000-uart";
+			reg = <0x10032000 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <49>;
+
+			clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+			clock-names = "baud", "module";
+
+			status = "disabled";
+		};
+
+		pinctrl: pin-controller@10010000 {
+			compatible = "ingenic,x1000-pinctrl";
+			reg = <0x10010000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpa: gpio@0 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <0>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 0 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <17>;
+			};
+
+			gpb: gpio@1 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <1>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 32 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <16>;
+			};
+
+			gpc: gpio@2 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <2>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 64 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <15>;
+			};
+
+			gpd: gpio@3 {
+				compatible = "ingenic,x1000-gpio";
+				reg = <3>;
+
+				gpio-controller;
+				gpio-ranges = <&pinctrl 0 96 32>;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&intc>;
+				interrupts = <14>;
+			};
+		};
+	};
+};
arch/mips/jz4740/Kconfig +6 -1
index 4dd0c44..6b96844 100644
@@ -33,3 +33,9 @@ config MACH_JZ4780
 	select MIPS_CPU_SCACHE
 	select SYS_HAS_CPU_MIPS32_R2
 	select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
--

2.7.4

#3 lore raw

Re: [PATCH v2 1/4] MIPS: Ingenic: initial X1000 support.

Hi Paul,

Quoted 74 lines · Paul Cercueil

Hi Zhou,

Quoted 70 lines · Zhou Yanjie

Support the Ingenic X1000 SoC using the code under arch/mips/jz4740. This is left unselectable in Kconfig until a X1000 based board is added in a later commit.

---

Notes:
v1->v2:
Rebase on top of mips-next, use ingenic-timer driver for system timer and clocksource.

 arch/mips/boot/dts/ingenic/x1000.dtsi | 183 
++++++++++++++++++++++++++++++++++
 arch/mips/jz4740/Kconfig              |   6 ++
 2 files changed, 189 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
arch/mips/boot/dts/ingenic/x1000.dtsi new file +46 -0
new file mode 100644
index 00000000..02a9b2a
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+
+/ {
+    #address-cells = <1>;
+    #size-cells = <1>;
+    compatible = "ingenic,x1000", "ingenic,x1000e";
+
+    cpuintc: interrupt-controller {
+        #address-cells = <0>;
+        #interrupt-cells = <1>;
+        interrupt-controller;
+        compatible = "mti,cpu-interrupt-controller";
+    };
+
+    intc: interrupt-controller@10001000 {
+        compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+        reg = <0x10001000 0x50>;
+
+        interrupt-controller;
+        #interrupt-cells = <1>;
+
+        interrupt-parent = <&cpuintc>;
+        interrupts = <2>;
+    };
+
+    exclk: ext {
+        compatible = "fixed-clock";
+        #clock-cells = <0>;
+    };
+
+    rtclk: rtc {
+        compatible = "fixed-clock";
+        #clock-cells = <0>;
+        clock-frequency = <32768>;
+    };
+
+    cgu: x1000-cgu@10000000 {
+        compatible = "ingenic,x1000-cgu";
+        reg = <0x10000000 0x100>;
+
+        #clock-cells = <1>;
+
+        clocks = <&exclk>, <&rtclk>;
+        clock-names = "ext", "rtc";
+    };
Quoted 9 lines

arch/mips/boot/dts/ingenic/x1000.dtsi line 52

Quoted 6 lines
arch/mips/boot/dts/ingenic/x1000.dtsi new file +6 -0
+
+    apb {
+        compatible = "simple-bus";
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges = <>;

You can drop the 'apb' node and list the children in the top node directly. That's what we do in the devicetree for the other Ingenic SoCs.

Sure, I'll drop it in v2.

Thanks and best regards!

Quoted 155 lines

Cheers,
-Paul

Quoted 149 lines
arch/mips/boot/dts/ingenic/x1000.dtsi new file +131 -0
+
+        tcu: timer@10002000 {
+            compatible = "ingenic,x1000-tcu",
+                     "ingenic,jz4770-tcu",
+                     "simple-mfd";
+            reg = <0x10002000 0x1000>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+            ranges = <0x0 0x10002000 0x1000>;
+
+            #clock-cells = <1>;
+
+            clocks = <&cgu X1000_CLK_RTCLK
+                  &cgu X1000_CLK_EXCLK
+                  &cgu X1000_CLK_PCLK>;
+            clock-names = "rtc", "ext", "pclk";
+
+            interrupt-controller;
+            #interrupt-cells = <1>;
+
+            interrupt-parent = <&intc>;
+            interrupts = <27 26 25>;
+        };
+
+        uart0: serial@10030000 {
+            compatible = "ingenic,x1000-uart";
+            reg = <0x10030000 0x100>;
+
+            interrupt-parent = <&intc>;
+            interrupts = <51>;
+
+            clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+            clock-names = "baud", "module";
+
+            status = "disabled";
+        };
+
+        uart1: serial@10031000 {
+            compatible = "ingenic,x1000-uart";
+            reg = <0x10031000 0x100>;
+
+            interrupt-parent = <&intc>;
+            interrupts = <50>;
+
+            clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+            clock-names = "baud", "module";
+
+            status = "disabled";
+        };
+
+        uart2: serial@10032000 {
+            compatible = "ingenic,x1000-uart";
+            reg = <0x10032000 0x100>;
+
+            interrupt-parent = <&intc>;
+            interrupts = <49>;
+
+            clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+            clock-names = "baud", "module";
+
+            status = "disabled";
+        };
+
+        pinctrl: pin-controller@10010000 {
+            compatible = "ingenic,x1000-pinctrl";
+            reg = <0x10010000 0x800>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            gpa: gpio@0 {
+                compatible = "ingenic,x1000-gpio";
+                reg = <0>;
+
+                gpio-controller;
+                gpio-ranges = <&pinctrl 0 0 32>;
+                #gpio-cells = <2>;
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+
+                interrupt-parent = <&intc>;
+                interrupts = <17>;
+            };
+
+            gpb: gpio@1 {
+                compatible = "ingenic,x1000-gpio";
+                reg = <1>;
+
+                gpio-controller;
+                gpio-ranges = <&pinctrl 0 32 32>;
+                #gpio-cells = <2>;
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+
+                interrupt-parent = <&intc>;
+                interrupts = <16>;
+            };
+
+            gpc: gpio@2 {
+                compatible = "ingenic,x1000-gpio";
+                reg = <2>;
+
+                gpio-controller;
+                gpio-ranges = <&pinctrl 0 64 32>;
+                #gpio-cells = <2>;
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+
+                interrupt-parent = <&intc>;
+                interrupts = <15>;
+            };
+
+            gpd: gpio@3 {
+                compatible = "ingenic,x1000-gpio";
+                reg = <3>;
+
+                gpio-controller;
+                gpio-ranges = <&pinctrl 0 96 32>;
+                #gpio-cells = <2>;
+
+                interrupt-controller;
+                #interrupt-cells = <2>;
+
+                interrupt-parent = <&intc>;
+                interrupts = <14>;
+            };
+        };
+    };
+};
arch/mips/jz4740/Kconfig +6 -0
index 4dd0c44..6b96844 100644
@@ -33,3 +33,9 @@ config MACH_JZ4780
     select MIPS_CPU_SCACHE
     select SYS_HAS_CPU_MIPS32_R2
     select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+    bool
+    select MIPS_CPU_SCACHE
+    select SYS_HAS_CPU_MIPS32_R2
+    select SYS_SUPPORTS_HIGHMEM
Signature · 1 line
2.7.4
#4 lore raw

PATCH v2 2/4 dt-bindings: Document yna vendor-prefix.

In reply to Zhou Yanjie

The "yna" is an acronym of the "YSH & ATIL".

---

Notes:

    v1->v2:
    No change.
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index 967e78c..47ddd88 100644
@@ -1054,6 +1054,8 @@ patternProperties:
     description: Xilinx
   "^xunlong,.*":
     description: Shenzhen Xunlong Software CO.,Limited
+  "^yna,.*":
+    description: YSH & ATIL
   "^yones-toptech,.*":
     description: Yones Toptech Co., Ltd.
   "^ysoft,.*":
Signature · 1 line
2.7.4
#5 lore raw

PATCH v2 3/4 dt-bindings: MIPS: Add Ingenic XBurst based boards.

In reply to Zhou Yanjie

Add Ingenic XBurst based boards, prepare for later dts.

---

Notes:

    v1->v2:
    No change.
 .../devicetree/bindings/mips/ingenic/devices.yaml  | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mips/ingenic/devices.yaml
Documentation/devicetree/bindings/mips/ingenic/devices.yaml new file +35 -0
new file mode 100644
index 00000000..8bb4b5d
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/ingenic/devices.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic XBurst based Platforms Device Tree Bindings
+
+maintainers:
+  - Zhou Yanjie <[email protected]>
+description: |
+  Devices with a Ingenic XBurst CPU shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Qi Hardware Ben NanoNote
+        items:
+          - const: qi,lb60
+
+      - description: Game Consoles Worldwide GCW Zero
+        items:
+          - const: gcw,zero
+
+      - description: MIPS Creator CI20
+        items:
+          - const: img,ci20
+
+      - description: YSH & ATIL General Module CU Neo
+        items:
+          - const: yna,cu1000
+...
Signature · 1 line
2.7.4
#6 lore raw

PATCH v2 4/4 MIPS: Ingenic: Initial YSH & ATIL CU Neo board. support.

In reply to Zhou Yanjie

Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board. Note that this is unselectable via Kconfig until the X1000 SoC is made selectable in a later commit.

---

Notes:
v1->v2:
Rebase on top of mips-next, use TCU for system timer and clocksource.

 arch/mips/boot/dts/ingenic/Makefile   |   1 +
 arch/mips/boot/dts/ingenic/cu1000.dts |  52 ++++++++++++++++++
 arch/mips/configs/cu1000_defconfig    | 100 ++++++++++++++++++++++++++++++++++
 arch/mips/jz4740/Kconfig              |   4 ++
 4 files changed, 157 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/cu1000.dts
 create mode 100644 arch/mips/configs/cu1000_defconfig
arch/mips/boot/dts/ingenic/Makefile +1 -0
index 9cc4844..f6db7bb 100644
@@ -2,5 +2,6 @@
 dtb-$(CONFIG_JZ4740_QI_LB60)	+= qi_lb60.dtb
 dtb-$(CONFIG_JZ4770_GCW0)	+= gcw0.dtb
 dtb-$(CONFIG_JZ4780_CI20)	+= ci20.dtb
+dtb-$(CONFIG_X1000_CU1000)	+= cu1000.dtb
 
 obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
arch/mips/boot/dts/ingenic/cu1000.dts new file +52 -0

52 lines not on this page · raw message

arch/mips/configs/cu1000_defconfig new file +100 -0

100 lines not on this page · raw message

arch/mips/jz4740/Kconfig +4 -0
index 6b96844..b4cee0a 100644
@@ -16,6 +16,10 @@ config JZ4780_CI20
 	bool "MIPS Creator CI20"
 	select MACH_JZ4780
 
+config X1000_CU1000
+	bool "YSH & ATIL General Module CU Neo"
+	select MACH_X1000
+
 endchoice
 
 config MACH_JZ4740
Signature · 1 line
2.7.4