Skip to contentSkip to conversation

hw/arm/smmuv3: Correct stream ID and event address handling

PATCH Superseded Simon Veith 2 participants 9 messages Dec 11, 2019 – Dec 16, 2019

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover hw/arm/smmuv3: Correct stream ID and event address handling

While working on the Linux SMMUv3 driver, I noticed a few cases where the QEMU SMMUv3 behavior relating to stream tables was inconsistent with our hardware.

Also, when debugging those differences, I found that the errors reported through the QEMU SMMUv3 event queue contained the address fields in an incorrect position.

These patches correct the QEMU SMMUv3 behavior to match the specification (and the behavior that I observed in our hardware). Linux guests normally will not notice these issues, but other SMMUv3 driver implementations might.

Simon Veith (6):
hw/arm/smmuv3: Apply address mask to linear strtab base address hw/arm/smmuv3: Correct SMMU_BASE_ADDR_MASK value hw/arm/smmuv3: Check stream IDs against actual table LOG2SIZE hw/arm/smmuv3: Align stream table base address to table size hw/arm/smmuv3: Use correct bit positions in EVT_SET_ADDR2 macro hw/arm/smmuv3: Report F_STE_FETCH fault address in correct word
position

 hw/arm/smmuv3-internal.h |  6 +++---
 hw/arm/smmuv3.c          | 28 +++++++++++++++++++++-------
 2 files changed, 24 insertions(+), 10 deletions(-)
Signature · 1 line
2.7.4
#1 lore raw

PATCH v2 1/6 hw/arm/smmuv3: Apply address mask to linear strtab base address

In the SMMU_STRTAB_BASE register, the stream table base address only occupies bits [51:6]. Other bits, such as RA (bit [62]), must be masked out to obtain the base address.

The branch for 2-level stream tables correctly applies this mask by way of SMMU_BASE_ADDR_MASK, but the one for linear stream tables does not.

Apply the missing mask in that case as well so that the correct stream base address is used by guests which configure a linear stream table.

Linux guests are unaffected by this change because they choose a 2-level stream table layout for the QEMU SMMUv3, based on the size of its stream ID space.

ref. ARM IHI 0070C, section 6.3.23.

---
 hw/arm/smmuv3.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/arm/smmuv3.c +1 -1
index e2fbb83..eef9a18 100644
@@ -429,7 +429,7 @@ static int smmu_find_ste(SMMUv3State *s, uint32_t sid, STE *ste,
         }
         addr = l2ptr + l2_ste_offset * sizeof(*ste);
     } else {
-        addr = s->strtab_base + sid * sizeof(*ste);
+        addr = (s->strtab_base & SMMU_BASE_ADDR_MASK) + sid * sizeof(*ste);
     }
 
     if (smmu_get_ste(s, addr, ste, event)) {
Signature · 1 line
2.7.4
#2 lore raw

PATCH v2 2/6 hw/arm/smmuv3: Correct SMMU_BASE_ADDR_MASK value

In reply to Simon Veith

There are two issues with the current value of SMMU_BASE_ADDR_MASK:

- At the lower end, we are clearing bits [4:0]. Per the SMMUv3 spec, we should also be treating bit 5 as zero in the base address.
- At the upper end, we are clearing bits [63:48]. Per the SMMUv3 spec, only bits [63:52] must be explicitly treated as zero.

Update the SMMU_BASE_ADDR_MASK value to mask out bits [63:52] and [5:0].

ref. ARM IHI 0070C, section 6.3.23.

---
 hw/arm/smmuv3-internal.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/arm/smmuv3-internal.h +1 -1
index d190181..042b435 100644
@@ -99,7 +99,7 @@ REG32(GERROR_IRQ_CFG2, 0x74)
 
 #define A_STRTAB_BASE      0x80 /* 64b */
 
-#define SMMU_BASE_ADDR_MASK 0xffffffffffe0
+#define SMMU_BASE_ADDR_MASK 0xfffffffffffc0
 
 REG32(STRTAB_BASE_CFG,     0x88)
     FIELD(STRTAB_BASE_CFG, FMT,      16, 2)
Signature · 1 line
2.7.4
#3 lore raw

PATCH v2 3/6 hw/arm/smmuv3: Check stream IDs against actual table LOG2SIZE

In reply to Simon Veith

When checking whether a stream ID is in range of the stream table, we have so far been only checking it against our implementation limit (SMMU_IDR1_SIDSIZE). However, the guest can program the STRTAB_BASE_CFG.LOG2SIZE field to a size that is smaller than this limit.

Check the stream ID against this limit as well to match the hardware behavior of raising C_BAD_STREAMID events in case the limit is exceeded. Also, ensure that we do not go one entry beyond the end of the table by checking that its index is strictly smaller than the table size.

ref. ARM IHI 0070C, section 6.3.24.

---
Changed in v2:

* Also check that stream ID is strictly lower than the table size

 hw/arm/smmuv3.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
hw/arm/smmuv3.c +6 -2
index eef9a18..727558b 100644
@@ -377,11 +377,15 @@ static int smmu_find_ste(SMMUv3State *s, uint32_t sid, STE *ste,
                          SMMUEventInfo *event)
 {
     dma_addr_t addr;
+    uint32_t log2size;
     int ret;
 
     trace_smmuv3_find_ste(sid, s->features, s->sid_split);
-    /* Check SID range */
-    if (sid > (1 << SMMU_IDR1_SIDSIZE)) {
+    log2size = FIELD_EX32(s->strtab_base_cfg, STRTAB_BASE_CFG, LOG2SIZE);
+    /*
+     * Check SID range against both guest-configured and implementation limits
+     */
+    if (sid >= (1 << MIN(log2size, SMMU_IDR1_SIDSIZE))) {
         event->type = SMMU_EVT_C_BAD_STREAMID;
         return -EINVAL;
     }
Signature · 1 line
2.7.4
#4 lore raw

PATCH v2 4/6 hw/arm/smmuv3: Align stream table base address to table size

Per the specification, and as observed in hardware, the SMMUv3 aligns the SMMU_STRTAB_BASE address to the size of the table by masking out the respective least significant bits in the ADDR field.

Apply this masking logic to our smmu_find_ste() lookup function per the specification.

ref. ARM IHI 0070C, section 6.3.23.

---
Changed in v2:

* Now using MAKE_64BIT_MASK()
* Eliminated unnecessary branches by using MAX()
* Removed unnecessary range check against DMA_ADDR_BITS

 hw/arm/smmuv3.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)
hw/arm/smmuv3.c +14 -4
index 727558b..31ac3ca 100644
@@ -376,8 +376,9 @@ bad_ste:
 static int smmu_find_ste(SMMUv3State *s, uint32_t sid, STE *ste,
                          SMMUEventInfo *event)
 {
-    dma_addr_t addr;
+    dma_addr_t addr, strtab_base;
     uint32_t log2size;
+    int strtab_size_shift;
     int ret;
 
     trace_smmuv3_find_ste(sid, s->features, s->sid_split);
@@ -391,10 +392,16 @@ static int smmu_find_ste(SMMUv3State *s, uint32_t sid, STE *ste,
     }
     if (s->features & SMMU_FEATURE_2LVL_STE) {
         int l1_ste_offset, l2_ste_offset, max_l2_ste, span;
-        dma_addr_t strtab_base, l1ptr, l2ptr;
+        dma_addr_t l1ptr, l2ptr;
         STEDesc l1std;
 
-        strtab_base = s->strtab_base & SMMU_BASE_ADDR_MASK;
+        /*
+         * Align strtab base address to table size. For this purpose, assume it
+         * is not bounded by SMMU_IDR1_SIDSIZE.
+         */
+        strtab_size_shift = MAX(5, (int)log2size - s->sid_split - 1 + 3);
+        strtab_base = s->strtab_base & SMMU_BASE_ADDR_MASK &
+                      ~MAKE_64BIT_MASK(0, strtab_size_shift);
         l1_ste_offset = sid >> s->sid_split;
         l2_ste_offset = sid & ((1 << s->sid_split) - 1);
         l1ptr = (dma_addr_t)(strtab_base + l1_ste_offset * sizeof(l1std));
@@ -433,7 +440,10 @@ static int smmu_find_ste(SMMUv3State *s, uint32_t sid, STE *ste,
         }
         addr = l2ptr + l2_ste_offset * sizeof(*ste);
     } else {
-        addr = (s->strtab_base & SMMU_BASE_ADDR_MASK) + sid * sizeof(*ste);
+        strtab_size_shift = log2size + 5;
+        strtab_base = s->strtab_base & SMMU_BASE_ADDR_MASK &
+                      ~MAKE_64BIT_MASK(0, strtab_size_shift);
+        addr = strtab_base + sid * sizeof(*ste);
     }
 
     if (smmu_get_ste(s, addr, ste, event)) {
Signature · 1 line
2.7.4
#5 lore raw

PATCH v2 5/6 hw/arm/smmuv3: Use correct bit positions in EVT_SET_ADDR2 macro

In reply to Simon Veith

The bit offsets in the EVT_SET_ADDR2 macro do not match those specified in the ARM SMMUv3 Architecture Specification. In all events that use this macro, e.g. F_WALK_EABT, the faulting fetch address or IPA actually occupies the 32-bit words 6 and 7 in the event record contiguously, with the upper and lower unused bits clear due to alignment or maximum supported address bits. How many bits are clear depends on the individual event type.

Update the macro to write to the correct words in the event record so that guest drivers can obtain accurate address information on events.

ref. ARM IHI 0070C, sections 7.3.12 through 7.3.16.

---
 hw/arm/smmuv3-internal.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/arm/smmuv3-internal.h +2 -2
index 0910e7c..994481d 100644
@@ -461,8 +461,8 @@ typedef struct SMMUEventInfo {
     } while (0)
 #define EVT_SET_ADDR2(x, addr)                            \
     do {                                                  \
-            (x)->word[7] = deposit32((x)->word[7], 3, 29, addr >> 16);   \
-            (x)->word[7] = deposit32((x)->word[7], 0, 16, addr & 0xffff);\
+            (x)->word[7] = (uint32_t)(addr >> 32);        \
+            (x)->word[6] = (uint32_t)(addr & 0xffffffff); \
     } while (0)
 
 void smmuv3_record_event(SMMUv3State *s, SMMUEventInfo *event);
Signature · 1 line
2.7.4
#6 lore raw

PATCH v2 6/6 hw/arm/smmuv3: Report F_STE_FETCH fault address in correct word position

In reply to Simon Veith

The smmuv3_record_event() function that generates the F_STE_FETCH error uses the EVT_SET_ADDR macro to record the fetch address, placing it in 32-bit words 4 and 5.

The correct position for this address is in words 6 and 7, per the SMMUv3 Architecture Specification.

Update the function to use the EVT_SET_ADDR2 macro instead, which is the macro intended for writing to these words.

ref. ARM IHI 0070C, section 7.3.4.

---
 hw/arm/smmuv3.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/arm/smmuv3.c +1 -1
index 31ac3ca..8b5f157 100644
@@ -172,7 +172,7 @@ void smmuv3_record_event(SMMUv3State *s, SMMUEventInfo *info)
     case SMMU_EVT_F_STE_FETCH:
         EVT_SET_SSID(&evt, info->u.f_ste_fetch.ssid);
         EVT_SET_SSV(&evt,  info->u.f_ste_fetch.ssv);
-        EVT_SET_ADDR(&evt, info->u.f_ste_fetch.addr);
+        EVT_SET_ADDR2(&evt, info->u.f_ste_fetch.addr);
         break;
     case SMMU_EVT_C_BAD_STE:
         EVT_SET_SSID(&evt, info->u.c_bad_ste.ssid);
Signature · 1 line
2.7.4
#7 lore raw
In reply to Simon Veith
Quoted 12 lines · Simon Veith

While working on the Linux SMMUv3 driver, I noticed a few cases where the QEMU SMMUv3 behavior relating to stream tables was inconsistent with our hardware.

Also, when debugging those differences, I found that the errors reported through the QEMU SMMUv3 event queue contained the address fields in an incorrect position.

These patches correct the QEMU SMMUv3 behavior to match the specification (and the behavior that I observed in our hardware). Linux guests normally will not notice these issues, but other SMMUv3 driver implementations might.

Quoted 8 lines

Simon Veith (6):
hw/arm/smmuv3: Apply address mask to linear strtab base address hw/arm/smmuv3: Correct SMMU_BASE_ADDR_MASK value hw/arm/smmuv3: Check stream IDs against actual table LOG2SIZE hw/arm/smmuv3: Align stream table base address to table size hw/arm/smmuv3: Use correct bit positions in EVT_SET_ADDR2 macro hw/arm/smmuv3: Report F_STE_FETCH fault address in correct word
position

Something funny seems to have happened when this series got sent out: patches 1,2,3 are correctly followups to the cover letter, but 4,5,6 are followups to patch 3.
This has confused patchew, which thinks the series is incomplete:

https://patchew.org/QEMU/[email protected]/[email protected]/

thanks
-- PMM

#8 lore raw
Quoted 3 lines · Peter Maydell

Something funny seems to have happened when this series got sent out: patches 1,2,3 are correctly followups to the cover letter, but 4,5,6 are followups to patch 3.

You are correct; I had fixed up one of the patches as I was sending them out, and though I had then added --in-reply-to pointing to the cover letter, git-send-email seems to have added another level of threading. Sorry about that. I'll resend the series again.

Regards
Simon

Amazon Development Center Germany GmbH
Krausenstr. 38
10117 Berlin
Geschaeftsfuehrung: Christian Schlaeger, Jonathan Weiss Eingetragen am Amtsgericht Charlottenburg unter HRB 149173 B
Sitz: Berlin
Ust-ID: DE 289 237 879