Add support for WLED5
Subsystems (5)
v3 cover Add support for WLED5
Currently, WLED driver supports only WLED4 peripherals that is present on pmi8998 and pm660L. This patch series converts the existing WLED4 bindings from .txt to .yaml format and adds the support for WLED5 peripheral that is present on PM8150L.
PM8150L WLED supports the following.
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options
- Multiple brightness width selection (12 bits to 15 bits)
Changes from V1:
- Rebased on top of the below commit.
backlight: qcom-wled: Fix unsigned comparison to zero
Changes from V2:
- Addressed Bjorn's comments by splitting the WLED4 changes in a seperate patch.
- Added WLED5 auto calibration support
Kiran Gunda (4):
backlight: qcom-wled: convert the wled bindings to .yaml format
backlight: qcom-wled: Add callbacks functions
backlight: qcom-wled: Add support for WLED5 peripheral in PM8150L
backlight: qcom-wled: Update auto calibration support for WLED5
.../bindings/leds/backlight/qcom-wled.txt | 154 ----- .../bindings/leds/backlight/qcom-wled.yaml | 223 ++++++++ drivers/video/backlight/qcom-wled.c | 622 ++++++++++++++++++--- 3 files changed, 772 insertions(+), 227 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v3 1/4 backlight: qcom-wled: convert the wled bindings to .yaml format
Convert the qcom-wled bindings from .txt to .yaml format.
--- .../bindings/leds/backlight/qcom-wled.txt | 154 ----------------- .../bindings/leds/backlight/qcom-wled.yaml | 184 +++++++++++++++++++++ 2 files changed, 184 insertions(+), 154 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted +0 -154
@@ -1,154 +0,0 @@ -Binding for Qualcomm Technologies, Inc. WLED driver - -WLED (White Light Emitting Diode) driver is used for controlling display -backlight that is part of PMIC on Qualcomm Technologies, Inc. reference -platforms. The PMIC is connected to the host processor via SPMI bus. - -- compatible - Usage: required - Value type: <string> - Definition: should be one of: - "qcom,pm8941-wled" - "qcom,pmi8998-wled" - "qcom,pm660l-wled" - -- reg - Usage: required - Value type: <prop encoded array> - Definition: Base address of the WLED modules. - -- default-brightness - Usage: optional - Value type: <u32> - Definition: brightness value on boot, value from: 0-4095. - Default: 2048 - -- label - Usage: required - Value type: <string> - Definition: The name of the backlight device - -- qcom,cs-out - Usage: optional - Value type: <bool> - Definition: enable current sink output. - This property is supported only for PM8941. - -- qcom,cabc - Usage: optional - Value type: <bool> - Definition: enable content adaptive backlight control. - -- qcom,ext-gen - Usage: optional - Value type: <bool> - Definition: use externally generated modulator signal to dim. - This property is supported only for PM8941. - -- qcom,current-limit - Usage: optional - Value type: <u32> - Definition: mA; per-string current limit; value from 0 to 25 with - 1 mA step. Default 20 mA. - This property is supported only for pm8941. - -- qcom,current-limit-microamp - Usage: optional - Value type: <u32> - Definition: uA; per-string current limit; value from 0 to 30000 with - 2500 uA step. Default 25 mA. - -- qcom,current-boost-limit - Usage: optional - Value type: <u32> - Definition: mA; boost current limit. - For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, - 1680. Default: 805 mA. - For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, - 1500. Default: 970 mA. - -- qcom,switching-freq - Usage: optional - Value type: <u32> - Definition: kHz; switching frequency; one of: 600, 640, 685, 738, - 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, - 4800, 9600. - Default: for pm8941: 1600 kHz - for pmi8998: 800 kHz - -- qcom,ovp - Usage: optional - Value type: <u32> - Definition: V; Over-voltage protection limit; one of: - 27, 29, 32, 35. Default: 29V - This property is supported only for PM8941. - -- qcom,ovp-millivolt - Usage: optional - Value type: <u32> - Definition: mV; Over-voltage protection limit; - For pmi8998: one of 18100, 19600, 29600, 31100. - Default 29600 mV. - If this property is not specified for PM8941, it - falls back to "qcom,ovp" property. - -- qcom,num-strings - Usage: optional - Value type: <u32> - Definition: #; number of led strings attached; - value: For PM8941 from 1 to 3. Default: 2 - For PMI8998 from 1 to 4. - -- interrupts - Usage: optional - Value type: <prop encoded array> - Definition: Interrupts associated with WLED. This should be - "short" and "ovp" interrupts. Interrupts can be - specified as per the encoding listed under - Documentation/devicetree/bindings/spmi/ - qcom,spmi-pmic-arb.txt. - -- interrupt-names - Usage: optional - Value type: <string> - Definition: Interrupt names associated with the interrupts. - Must be "short" and "ovp". The short circuit detection - is not supported for PM8941. - -- qcom,enabled-strings - Usage: optional - Value tyoe: <u32 array> - Definition: Array of the WLED strings numbered from 0 to 3. Each - string of leds are operated individually. Specify the - list of strings used by the device. Any combination of - led strings can be used. - -- qcom,external-pfet - Usage: optional - Value type: <bool> - Definition: Specify if external PFET control for short circuit - protection is used. This property is supported only - for PMI8998. - -- qcom,auto-string-detection - Usage: optional - Value type: <bool> - Definition: Enables auto-detection of the WLED string configuration. - This feature is not supported for PM8941. - - -Example: - -pm8941-wled@d800 { - compatible = "qcom,pm8941-wled"; - reg = <0xd800>; - label = "backlight"; - - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; - qcom,enabled-strings = <0 1>; -};
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file +184 -0
184 lines not on this page · raw message
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH V3 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format
Quoted 3 lines · Kiran Gunda
Convert the qcom-wled bindings from .txt to .yaml format.
Signed-off-by Kiran Gunda <[email protected]>
Quoted 360 lines
--- .../bindings/leds/backlight/qcom-wled.txt | 154 ----------------- .../bindings/leds/backlight/qcom-wled.yaml | 184 +++++++++++++++++++++ 2 files changed, 184 insertions(+), 154 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yamlDocumentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted +0
-154@@ -1,154 +0,0 @@ -Binding for Qualcomm Technologies, Inc. WLED driver - -WLED (White Light Emitting Diode) driver is used for controlling display -backlight that is part of PMIC on Qualcomm Technologies, Inc. reference -platforms. The PMIC is connected to the host processor via SPMI bus. - -- compatible - Usage: required - Value type: <string> - Definition: should be one of: - "qcom,pm8941-wled" - "qcom,pmi8998-wled" - "qcom,pm660l-wled" - -- reg - Usage: required - Value type: <prop encoded array> - Definition: Base address of the WLED modules. - -- default-brightness - Usage: optional - Value type: <u32> - Definition: brightness value on boot, value from: 0-4095. - Default: 2048 - -- label - Usage: required - Value type: <string> - Definition: The name of the backlight device - -- qcom,cs-out - Usage: optional - Value type: <bool> - Definition: enable current sink output. - This property is supported only for PM8941. - -- qcom,cabc - Usage: optional - Value type: <bool> - Definition: enable content adaptive backlight control. - -- qcom,ext-gen - Usage: optional - Value type: <bool> - Definition: use externally generated modulator signal to dim. - This property is supported only for PM8941. - -- qcom,current-limit - Usage: optional - Value type: <u32> - Definition: mA; per-string current limit; value from 0 to 25 with - 1 mA step. Default 20 mA. - This property is supported only for pm8941. - -- qcom,current-limit-microamp - Usage: optional - Value type: <u32> - Definition: uA; per-string current limit; value from 0 to 30000 with - 2500 uA step. Default 25 mA. - -- qcom,current-boost-limit - Usage: optional - Value type: <u32> - Definition: mA; boost current limit. - For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, - 1680. Default: 805 mA. - For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, - 1500. Default: 970 mA. - -- qcom,switching-freq - Usage: optional - Value type: <u32> - Definition: kHz; switching frequency; one of: 600, 640, 685, 738, - 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, - 4800, 9600. - Default: for pm8941: 1600 kHz - for pmi8998: 800 kHz - -- qcom,ovp - Usage: optional - Value type: <u32> - Definition: V; Over-voltage protection limit; one of: - 27, 29, 32, 35. Default: 29V - This property is supported only for PM8941. - -- qcom,ovp-millivolt - Usage: optional - Value type: <u32> - Definition: mV; Over-voltage protection limit; - For pmi8998: one of 18100, 19600, 29600, 31100. - Default 29600 mV. - If this property is not specified for PM8941, it - falls back to "qcom,ovp" property. - -- qcom,num-strings - Usage: optional - Value type: <u32> - Definition: #; number of led strings attached; - value: For PM8941 from 1 to 3. Default: 2 - For PMI8998 from 1 to 4. - -- interrupts - Usage: optional - Value type: <prop encoded array> - Definition: Interrupts associated with WLED. This should be - "short" and "ovp" interrupts. Interrupts can be - specified as per the encoding listed under - Documentation/devicetree/bindings/spmi/ - qcom,spmi-pmic-arb.txt. - -- interrupt-names - Usage: optional - Value type: <string> - Definition: Interrupt names associated with the interrupts. - Must be "short" and "ovp". The short circuit detection - is not supported for PM8941. - -- qcom,enabled-strings - Usage: optional - Value tyoe: <u32 array> - Definition: Array of the WLED strings numbered from 0 to 3. Each - string of leds are operated individually. Specify the - list of strings used by the device. Any combination of - led strings can be used. - -- qcom,external-pfet - Usage: optional - Value type: <bool> - Definition: Specify if external PFET control for short circuit - protection is used. This property is supported only - for PMI8998. - -- qcom,auto-string-detection - Usage: optional - Value type: <bool> - Definition: Enables auto-detection of the WLED string configuration. - This feature is not supported for PM8941. - - -Example: - -pm8941-wled@d800 { - compatible = "qcom,pm8941-wled"; - reg = <0xd800>; - label = "backlight"; - - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; - qcom,enabled-strings = <0 1>; -};Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file +184
-0@@ -0,0 +1,184 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/leds/backlight/qcom-wled.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for Qualcomm Technologies, Inc. WLED driver + +maintainers: + - Lee Jones <[email protected]> + +description: | + WLED (White Light Emitting Diode) driver is used for controlling display + backlight that is part of PMIC on Qualcomm Technologies, Inc. reference + platforms. The PMIC is connected to the host processor via SPMI bus. + +properties: + compatible : + enum: + - qcom,pm8941-wled + - qcom,pmi8998-wled + - qcom,pm660l-wled + + reg: + maxItems: 1 + + default-brightness: + maxItems: 1 + description: + brightness value on boot, value from 0-4095. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + default: 2048 + + label: + maxItems: 1 + description: + The name of the backlight device. + allOf: + - $ref: /schemas/types.yaml#/definitions/string + + qcom,cs-out: + description: + enable current sink output. + This property is supported only for PM8941. + type: boolean + + qcom,cabc: + description: + enable content adaptive backlight control. + type: boolean + + qcom,ext-gen: + description: + use externally generated modulator signal to dim. + This property is supported only for PM8941. + type: boolean + + qcom,current-limit: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + mA; per-string current limit; value from 0 to 25 with + 1 mA step. This property is supported only for pm8941. + default: 20 + + qcom,current-limit-microamp: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + uA; per-string current limit; value from 0 to 30000 with + 2500 uA step. + default: 25 + + qcom,current-boost-limit: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + mA; boost current limit. + For pm8941 one of 105, 385, 525, 805, 980, 1260, 1400, 1680. + Default, 805 mA. + For pmi8998 one of 105, 280, 450, 620, 970, 1150, 1300, + 1500. Default 970 mA. + + qcom,switching-freq: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + kHz; switching frequency; one of 600, 640, 685, 738, + 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, + 4800, 9600. + Default for pm8941 1600 kHz + for pmi8998 800 kHz + + qcom,ovp: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + V; Over-voltage protection limit; one of 27, 29, 32, 35. Default 29V + This property is supported only for PM8941. + + qcom,ovp-millivolt: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + mV; Over-voltage protection limit; + For pmi8998 one of 18100, 19600, 29600, 31100. + Default 29600 mV. + If this property is not specified for PM8941, it + falls back to "qcom,ovp" property. + + qcom,num-strings: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + number of led strings attached; + value for PM8941 from 1 to 3. Default 2 + For PMI8998 from 1 to 4. + + interrupts: + maxItems: 2 + description: + Interrupts associated with WLED. This should be + "short" and "ovp" interrupts. Interrupts can be + specified as per the encoding listed under + Documentation/devicetree/bindings/spmi/ + qcom,spmi-pmic-arb.txt. + + interrupt-names: + description: + Interrupt names associated with the interrupts. + Must be "short" and "ovp". The short circuit detection + is not supported for PM8941. + + qcom,enabled-strings: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + + qcom,external-pfet: + description: + Specify if external PFET control for short circuit + protection is used. This property is supported only + for PMI8998. + type: boolean + + qcom,auto-string-detection: + description: + Enables auto-detection of the WLED string configuration. + This feature is not supported for PM8941. + type: boolean + +required: + - compatible + - reg + - label + +examples: + - | + pm8941-wled@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800 0x100>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + qcom,enabled-strings = <0 1>; + };Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH V3 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format
Quoted 7 lines · Daniel Thompson
Quoted 3 lines · Kiran Gunda
Convert the qcom-wled bindings from .txt to .yaml format.
Signed-off-by Kiran Gunda <[email protected]>Acked-by Daniel Thompson <[email protected]>
Thanks.
Quoted 374 lines
Quoted 374 lines
--- .../bindings/leds/backlight/qcom-wled.txt | 154 ----------------- .../bindings/leds/backlight/qcom-wled.yaml | 184 +++++++++++++++++++++ 2 files changed, 184 insertions(+), 154 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yamlDocumentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted +0
-3@@ -1,154 +0,0 @@ -Binding for Qualcomm Technologies, Inc. WLED driver - -WLED (White Light Emitting Diode) driver is used for controllingdisplay
-backlight that is part of PMIC on Qualcomm Technologies, Inc. referenceDocumentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted +0
-54-platforms. The PMIC is connected to the host processor via SPMI bus. - -- compatible - Usage: required - Value type: <string> - Definition: should be one of: - "qcom,pm8941-wled" - "qcom,pmi8998-wled" - "qcom,pm660l-wled" - -- reg - Usage: required - Value type: <prop encoded array> - Definition: Base address of the WLED modules. - -- default-brightness - Usage: optional - Value type: <u32> - Definition: brightness value on boot, value from: 0-4095. - Default: 2048 - -- label - Usage: required - Value type: <string> - Definition: The name of the backlight device - -- qcom,cs-out - Usage: optional - Value type: <bool> - Definition: enable current sink output. - This property is supported only for PM8941. - -- qcom,cabc - Usage: optional - Value type: <bool> - Definition: enable content adaptive backlight control. - -- qcom,ext-gen - Usage: optional - Value type: <bool> - Definition: use externally generated modulator signal to dim. - This property is supported only for PM8941. - -- qcom,current-limit - Usage: optional - Value type: <u32> - Definition: mA; per-string current limit; value from 0 to 25 with - 1 mA step. Default 20 mA. - This property is supported only for pm8941. - -- qcom,current-limit-microamp - Usage: optional - Value type: <u32> - Definition: uA; per-string current limit; value from 0 to 30000with
Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted +0
-78- 2500 uA step. Default 25 mA. - -- qcom,current-boost-limit - Usage: optional - Value type: <u32> - Definition: mA; boost current limit. - For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, - 1680. Default: 805 mA. - For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, - 1500. Default: 970 mA. - -- qcom,switching-freq - Usage: optional - Value type: <u32> - Definition: kHz; switching frequency; one of: 600, 640, 685, 738, - 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, - 4800, 9600. - Default: for pm8941: 1600 kHz - for pmi8998: 800 kHz - -- qcom,ovp - Usage: optional - Value type: <u32> - Definition: V; Over-voltage protection limit; one of: - 27, 29, 32, 35. Default: 29V - This property is supported only for PM8941. - -- qcom,ovp-millivolt - Usage: optional - Value type: <u32> - Definition: mV; Over-voltage protection limit; - For pmi8998: one of 18100, 19600, 29600, 31100. - Default 29600 mV. - If this property is not specified for PM8941, it - falls back to "qcom,ovp" property. - -- qcom,num-strings - Usage: optional - Value type: <u32> - Definition: #; number of led strings attached; - value: For PM8941 from 1 to 3. Default: 2 - For PMI8998 from 1 to 4. - -- interrupts - Usage: optional - Value type: <prop encoded array> - Definition: Interrupts associated with WLED. This should be - "short" and "ovp" interrupts. Interrupts can be - specified as per the encoding listed under - Documentation/devicetree/bindings/spmi/ - qcom,spmi-pmic-arb.txt. - -- interrupt-names - Usage: optional - Value type: <string> - Definition: Interrupt names associated with the interrupts. - Must be "short" and "ovp". The short circuit detection - is not supported for PM8941. - -- qcom,enabled-strings - Usage: optional - Value tyoe: <u32 array> - Definition: Array of the WLED strings numbered from 0 to 3. Each - string of leds are operated individually. Specify the - list of strings used by the device. Any combination of - led strings can be used. - -- qcom,external-pfet - Usage: optional - Value type: <bool> - Definition: Specify if external PFET control for short circuit - protection is used. This property is supported only - for PMI8998. - -- qcom,auto-string-detection - Usage: optional - Value type: <bool> - Definition: Enables auto-detection of the WLED stringconfiguration.
Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted +0
-18- This feature is not supported for PM8941. - - -Example: - -pm8941-wled@d800 { - compatible = "qcom,pm8941-wled"; - reg = <0xd800>; - label = "backlight"; - - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; - qcom,enabled-strings = <0 1>; -};Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file +4
-0@@ -0,0 +1,184 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id:http://devicetree.org/schemas/bindings/leds/backlight/qcom-wled.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file +8
-0+ +title: Binding for Qualcomm Technologies, Inc. WLED driver + +maintainers: + - Lee Jones <[email protected]> + +description: | + WLED (White Light Emitting Diode) driver is used for controllingdisplay
+ backlight that is part of PMIC on Qualcomm Technologies, Inc. reference
+ platforms. The PMIC is connected to the host processor via SPMI bus.Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file +89
-0+ +properties: + compatible : + enum: + - qcom,pm8941-wled + - qcom,pmi8998-wled + - qcom,pm660l-wled + + reg: + maxItems: 1 + + default-brightness: + maxItems: 1 + description: + brightness value on boot, value from 0-4095. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + default: 2048 + + label: + maxItems: 1 + description: + The name of the backlight device. + allOf: + - $ref: /schemas/types.yaml#/definitions/string + + qcom,cs-out: + description: + enable current sink output. + This property is supported only for PM8941. + type: boolean + + qcom,cabc: + description: + enable content adaptive backlight control. + type: boolean + + qcom,ext-gen: + description: + use externally generated modulator signal to dim. + This property is supported only for PM8941. + type: boolean + + qcom,current-limit: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + mA; per-string current limit; value from 0 to 25 with + 1 mA step. This property is supported only for pm8941. + default: 20 + + qcom,current-limit-microamp: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + uA; per-string current limit; value from 0 to 30000 with + 2500 uA step. + default: 25 + + qcom,current-boost-limit: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + mA; boost current limit. + For pm8941 one of 105, 385, 525, 805, 980, 1260, 1400, 1680. + Default, 805 mA. + For pmi8998 one of 105, 280, 450, 620, 970, 1150, 1300, + 1500. Default 970 mA. + + qcom,switching-freq: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + kHz; switching frequency; one of 600, 640, 685, 738, + 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, + 4800, 9600. + Default for pm8941 1600 kHz + for pmi8998 800 kHz + + qcom,ovp: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + V; Over-voltage protection limit; one of 27, 29, 32, 35.Default 29V
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file +80
-1+ This property is supported only for PM8941. + + qcom,ovp-millivolt: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + mV; Over-voltage protection limit; + For pmi8998 one of 18100, 19600, 29600, 31100. + Default 29600 mV. + If this property is not specified for PM8941, it + falls back to "qcom,ovp" property. + + qcom,num-strings: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + number of led strings attached; + value for PM8941 from 1 to 3. Default 2 + For PMI8998 from 1 to 4. + + interrupts: + maxItems: 2 + description: + Interrupts associated with WLED. This should be + "short" and "ovp" interrupts. Interrupts can be + specified as per the encoding listed under + Documentation/devicetree/bindings/spmi/ + qcom,spmi-pmic-arb.txt. + + interrupt-names: + description: + Interrupt names associated with the interrupts. + Must be "short" and "ovp". The short circuit detection + is not supported for PM8941. + + qcom,enabled-strings: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + + qcom,external-pfet: + description: + Specify if external PFET control for short circuit + protection is used. This property is supported only + for PMI8998. + type: boolean + + qcom,auto-string-detection: + description: + Enables auto-detection of the WLED string configuration. + This feature is not supported for PM8941. + type: boolean + +required: + - compatible + - reg + - label + +examples: + - | + pm8941-wled@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800 0x100>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + qcom,enabled-strings = <0 1>; + }; --The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Rob Herring
maintainerRe: [PATCH V3 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format
In reply to Kiran GundaQuoted 10 lines · Kiran Gunda
Convert the qcom-wled bindings from .txt to .yaml format.
Signed-off-by Kiran Gunda <[email protected]>--- .../bindings/leds/backlight/qcom-wled.txt | 154 ----------------- .../bindings/leds/backlight/qcom-wled.yaml | 184 +++++++++++++++++++++ 2 files changed, 184 insertions(+), 154 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
My bot found errors running 'make dt_binding_check' on your patch:
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml#
See https://patchwork.ozlabs.org/patch/1251567
Please check and re-submit.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH V3 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format
Quoted 16 lines · Rob Herring
Quoted 12 lines · Kiran Gunda
Convert the qcom-wled bindings from .txt to .yaml format.
Signed-off-by Kiran Gunda <[email protected]>--- .../bindings/leds/backlight/qcom-wled.txt | 154 ----------------- .../bindings/leds/backlight/qcom-wled.yaml | 184 +++++++++++++++++++++ 2 files changed, 184 insertions(+), 154 deletions(-) delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt create mode 100644Quoted 2 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
Quoted 8 lines
My bot found errors running 'make
dt_binding_check' on your patch:
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml: $id:
relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml#See https://patchwork.ozlabs.org/patch/1251567
Please check and re-submit.
I will fix it in next post.
PATCH v3 2/4 backlight: qcom-wled: Add callback functions
In reply to Kiran GundaAdd cabc_config, sync_toggle, wled_ovp_fault_status and wled_ovp_delay callback functions to prepare the driver for adding WLED5 support.
--- drivers/video/backlight/qcom-wled.c | 196 +++++++++++++++++++++++------------- 1 file changed, 126 insertions(+), 70 deletions(-)
drivers/video/backlight/qcom-wled.c +126 -70
@@ -128,6 +128,7 @@ struct wled_config {bool cs_out_en;bool ext_gen;bool cabc; +bool en_cabc;bool external_pfet;bool auto_detection_enabled; };
@@ -147,14 +148,20 @@ struct wled {u32 max_brightness;u32 short_count;u32 auto_detect_count; +u32 version;bool disabled_by_short;bool has_short_detect; +bool cabc_disabled;int short_irq;int ovp_irq;struct wled_config cfg;struct delayed_work ovp_work;int (*wled_set_brightness)(struct wled *wled,u16 brightness); +int (*cabc_config)(struct wled *wled,bool enable); +int (*wled_sync_toggle)(struct wled *wled); +int (*wled_ovp_fault_status)(struct wled *wled,bool *fault_set); +int (*wled_ovp_delay)(struct wled *wled); };static int wled3_set_brightness (struct wled *wled,u16 brightness)
@@ -237,7 +244,7 @@ static int wled_module_enable(struct wled *wled, int val)return 0 ; } -static int wled_sync_toggle (struct wled *wled) +static int wled3_sync_toggle (struct wled *wled) {int rc;unsigned int mask =GENMASK (wled->max_string_count -1 ,0 );
@@ -255,6 +262,46 @@ static int wled_sync_toggle(struct wled *wled)return rc; } +static int wled4_ovp_fault_status (struct wled *wled,bool *fault_set) +{ +int rc; +u32 int_rt_sts, fault_sts; + + *fault_set = false; + rc =regmap_read (wled->regmap, + wled->ctrl_addr +WLED3_CTRL_REG_INT_RT_STS , + &int_rt_sts); +if (rc <0 ) { +dev_err (wled->dev,"Failed to read INT_RT_STS rc=%d\n" , rc); +return rc; + } + + rc =regmap_read (wled->regmap, + wled->ctrl_addr +WLED3_CTRL_REG_FAULT_STATUS , + &fault_sts); +if (rc <0 ) { +dev_err (wled->dev,"Failed to read FAULT_STATUS rc=%d\n" , rc); +return rc; + } + +if (int_rt_sts &WLED3_CTRL_REG_OVP_FAULT_STATUS ) + *fault_set = true; + +if (fault_sts &WLED3_CTRL_REG_OVP_FAULT_BIT ) + *fault_set = true; + +if (*fault_set) +dev_dbg (wled->dev,"WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n" , + int_rt_sts, fault_sts); + +return rc; +} + +static int wled4_ovp_delay (struct wled *wled) +{ +return WLED_SOFT_START_DLY_US ; +} +static int wled_update_status (struct backlight_device *bl) {struct wled *wled =bl_get_data (bl);
@@ -275,7 +322,7 @@ static int wled_update_status(struct backlight_device *bl) goto unlock_mutex; } - rc =wled_sync_toggle (wled); + rc = wled->wled_sync_toggle (wled);if (rc <0 ) {dev_err (wled->dev,"wled sync failed rc:%d\n" , rc); goto unlock_mutex;
@@ -298,6 +345,31 @@ static int wled_update_status(struct backlight_device *bl)return rc; } +static int wled4_cabc_config (struct wled *wled,bool enable) +{ +int i, j, rc; +u8 val; + +if (wled->cabc_disabled) +return 0 ; + +for (i =0 ; i < wled->cfg.num_strings; i++) { + j = wled->cfg.enabled_strings[i]; + + val = enable ?WLED4_SINK_REG_STR_CABC_MASK :0 ; + rc =regmap_update_bits (wled->regmap, wled->sink_addr + +WLED4_SINK_REG_STR_CABC (j), +WLED4_SINK_REG_STR_CABC_MASK , val); +if (rc <0 ) +return rc; + } + +if (!wled->cfg.en_cabc) + wled->cabc_disabled = true; + +return 0 ; +} +#define WLED_SHORT_DLY_MS 20#define WLED_SHORT_CNT_MAX 5#define WLED_SHORT_RESET_CNT_DLY_US USEC_PER_SEC
@@ -345,9 +417,10 @@ static irqreturn_t wled_short_irq_handler(int irq, void *_wled)static void wled_auto_string_detection (struct wled *wled) { -int rc =0 , i; -u32 sink_config =0 , int_sts; +int rc =0 , i, delay_time_us; +u32 sink_config =0 ;u8 sink_test =0 , sink_valid =0 , val; +bool fault_set;/* Read configured sink configuration */ rc = regmap_read(wled->regmap, wled->sink_addr +
@@ -376,14 +449,9 @@ static void wled_auto_string_detection(struct wled *wled) }if (wled->cfg.cabc) { -for (i =0 ; i < wled->cfg.num_strings; i++) { - rc =regmap_update_bits (wled->regmap, wled->sink_addr + -WLED4_SINK_REG_STR_CABC (i), -WLED4_SINK_REG_STR_CABC_MASK , -0 ); -if (rc <0 ) - goto failed_detect; - } + rc = wled->cabc_config (wled,0 ); +if (rc <0 ) + goto failed_detect; }/* Disable all sinks */
@@ -427,18 +495,17 @@ static void wled_auto_string_detection(struct wled *wled) goto failed_detect; } -usleep_range (WLED_SOFT_START_DLY_US , -WLED_SOFT_START_DLY_US +1000 ); + delay_time_us = wled->wled_ovp_delay (wled); +usleep_range (delay_time_us, delay_time_us +1000 ); - rc =regmap_read (wled->regmap, wled->ctrl_addr + -WLED3_CTRL_REG_INT_RT_STS , &int_sts); + rc = wled->wled_ovp_fault_status (wled, &fault_set);if (rc <0 ) { -dev_err (wled->dev,"Error in reading WLED3_CTRL_INT_RT_STS rc=%d\n" , +dev_err (wled->dev,"Error in getting OVP fault_sts, rc=%d\n" , rc); goto failed_detect; } -if (int_sts &WLED3_CTRL_REG_OVP_FAULT_STATUS ) +if (fault_set)dev_dbg (wled->dev,"WLED OVP fault detected with SINK %d\n" , i +1 );else
@@ -478,30 +545,30 @@ static void wled_auto_string_detection(struct wled *wled) }/* Enable valid sinks */ -for (i =0 ; i < wled->cfg.num_strings; i++) { -if (wled->cfg.cabc) { - rc =regmap_update_bits (wled->regmap, wled->sink_addr + -WLED4_SINK_REG_STR_CABC (i), -WLED4_SINK_REG_STR_CABC_MASK , -WLED4_SINK_REG_STR_CABC_MASK ); -if (rc <0 ) +if (wled->version ==4 ) { +for (i =0 ; i < wled->cfg.num_strings; i++) { +if (sink_config & +BIT (WLED4_SINK_REG_CURR_SINK_SHFT + i)) + val =WLED4_SINK_REG_STR_MOD_MASK ; +else +/* Disable modulator_en for unused sink */ + val =0x0 ; + + rc =regmap_write (wled->regmap, wled->sink_addr + +WLED4_SINK_REG_STR_MOD_EN (i), val); +if (rc <0 ) { +dev_err (wled->dev,"Failed to configure MODULATOR_EN rc=%d\n" , + rc); goto failed_detect; - } - -if (sink_config &BIT (WLED4_SINK_REG_CURR_SINK_SHFT + i)) - val =WLED4_SINK_REG_STR_MOD_MASK ; -else - val =0x0 ;/* Disable modulator_en for unused sink */ - - rc =regmap_write (wled->regmap, wled->sink_addr + -WLED4_SINK_REG_STR_MOD_EN (i), val); -if (rc <0 ) { -dev_err (wled->dev,"Failed to configure MODULATOR_EN rc=%d\n" , - rc); - goto failed_detect; + } } } +/* Enable CABC if it needs to be enabled */ + rc = wled->cabc_config (wled, true); +if (rc <0 ) + goto failed_detect; +/* Restore the feedback setting */ rc =regmap_write (wled->regmap, wled->ctrl_addr +WLED3_CTRL_REG_FEEDBACK_CONTROL ,0 );
@@ -570,29 +637,19 @@ static bool wled_auto_detection_required(struct wled *wled)static int wled_auto_detection_at_init (struct wled *wled) {int rc; -u32 fault_status, rt_status; +bool fault_set;if (!wled->cfg.auto_detection_enabled)return 0 ; - rc =regmap_read (wled->regmap, - wled->ctrl_addr +WLED3_CTRL_REG_INT_RT_STS , - &rt_status); + rc = wled->wled_ovp_fault_status (wled, &fault_set);if (rc <0 ) { -dev_err (wled->dev,"Failed to read RT status rc=%d\n" , rc); -return rc; - } - - rc =regmap_read (wled->regmap, - wled->ctrl_addr +WLED3_CTRL_REG_FAULT_STATUS , - &fault_status); -if (rc <0 ) { -dev_err (wled->dev,"Failed to read fault status rc=%d\n" , rc); +dev_err (wled->dev,"Error in getting OVP fault_sts, rc=%d\n" , + rc);return rc; } -if ((rt_status &WLED3_CTRL_REG_OVP_FAULT_STATUS ) || - (fault_status &WLED3_CTRL_REG_OVP_FAULT_BIT )) { +if (fault_set) {mutex_lock (&wled->lock);wled_auto_string_detection (wled);mutex_unlock (&wled->lock);
@@ -811,17 +868,12 @@ static int wled4_setup(struct wled *wled) wled->cfg.string_i_limit);if (rc <0 )return rc; - - addr = wled->sink_addr + -WLED4_SINK_REG_STR_CABC (j); - rc =regmap_update_bits (wled->regmap, addr, -WLED4_SINK_REG_STR_CABC_MASK , - wled->cfg.cabc ? -WLED4_SINK_REG_STR_CABC_MASK :0 ); -if (rc <0 ) -return rc; } + rc =wled4_cabc_config (wled, wled->cfg.en_cabc); +if (rc <0 ) +return rc; + rc = regmap_update_bits(wled->regmap, wled->ctrl_addr + WLED3_CTRL_REG_MOD_EN, WLED3_CTRL_REG_MOD_EN_MASK,
@@ -835,7 +887,7 @@ static int wled4_setup(struct wled *wled)if (rc <0 )return rc; - rc =wled_sync_toggle (wled); + rc = wled->wled_sync_toggle (wled);if (rc <0 ) {dev_err (wled->dev,"Failed to toggle sync reg rc:%d\n" , rc);return rc;
@@ -951,7 +1003,7 @@ static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx)return idx; } -static int wled_configure (struct wled *wled,int version) +static int wled_configure (struct wled *wled) {struct wled_config *cfg = &wled->cfg;struct device *dev = wled->dev;
@@ -1035,12 +1087,13 @@ static int wled_configure(struct wled *wled, int version)if (rc) wled->name =devm_kasprintf (dev,GFP_KERNEL ,"%pOFn" , dev->of_node); -switch (version) { +switch (wled->version) {case 3 : u32_opts = wled3_opts; size =ARRAY_SIZE (wled3_opts); *cfg = wled3_config_defaults; wled->wled_set_brightness = wled3_set_brightness; + wled->wled_sync_toggle = wled3_sync_toggle; wled->max_string_count =3 ; wled->sink_addr = wled->ctrl_addr;break ;
@@ -1050,6 +1103,10 @@ static int wled_configure(struct wled *wled, int version) size =ARRAY_SIZE (wled4_opts); *cfg = wled4_config_defaults; wled->wled_set_brightness = wled4_set_brightness; + wled->wled_sync_toggle = wled3_sync_toggle; + wled->cabc_config = wled4_cabc_config; + wled->wled_ovp_fault_status = wled4_ovp_fault_status; + wled->wled_ovp_delay = wled4_ovp_delay; wled->max_string_count =4 ; prop_addr =of_get_address (dev->of_node,1 ,NULL ,NULL );
@@ -1186,7 +1243,6 @@ static int wled_probe(struct platform_device *pdev)struct backlight_device *bl;struct wled *wled;struct regmap *regmap; -int version;u32 val;int rc;
@@ -1203,18 +1259,18 @@ static int wled_probe(struct platform_device *pdev) wled->regmap = regmap; wled->dev = &pdev->dev; - version = (uintptr_t )of_device_get_match_data (&pdev->dev); -if (!version) { + wled->version = (uintptr_t )of_device_get_match_data (&pdev->dev); +if (!wled->version) {dev_err (&pdev->dev,"Unknown device version\n" );return -ENODEV ; }mutex_init (&wled->lock); - rc =wled_configure (wled, version); + rc =wled_configure (wled);if (rc)return rc; -switch (version) { +switch (wled->version) {case 3 : wled->cfg.auto_detection_enabled = false; rc =wled3_setup (wled);
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH V3 2/4] backlight: qcom-wled: Add callback functions
Quoted 4 lines · Kiran Gunda
Add
cabc_config,sync_toggle,wled_ovp_fault_statusandwled_ovp_delaycallback functions to prepare the driver for adding WLED5 support.Signed-off-by Kiran Gunda <[email protected]>
Overall this code would a lot easier to review if
drivers/video/backlight/qcom-wled.c struct wled_config { · line 131
Quoted 13 lines
--- drivers/video/backlight/qcom-wled.c | 196 +++++++++++++++++++++++------------- 1 file changed, 126 insertions(+), 70 deletions(-)drivers/video/backlight/qcom-wled.c +1
-0@@ -128,6 +128,7 @@ struct wled_config {bool cs_out_en;bool ext_gen;bool cabc; +bool en_cabc;
Does this ever get set to true?
Quoted 11 lines
drivers/video/backlight/qcom-wled.c +2
-0bool external_pfet;bool auto_detection_enabled; };@@ -147,14 +148,20 @@ struct wled {u32 max_brightness;u32 short_count;u32 auto_detect_count; +u32 version;bool disabled_by_short;bool has_short_detect; +bool cabc_disabled;
drivers/video/backlight/qcom-wled.c struct wled { · line 164
Quoted 10 lines
drivers/video/backlight/qcom-wled.c +4
-0int short_irq;int ovp_irq;struct wled_config cfg;struct delayed_work ovp_work;int (*wled_set_brightness)(struct wled *wled,u16 brightness); +int (*cabc_config)(struct wled *wled,bool enable); +int (*wled_sync_toggle)(struct wled *wled); +int (*wled_ovp_fault_status)(struct wled *wled,bool *fault_set); +int (*wled_ovp_delay)(struct wled *wled);
Let's get some doc comments explaining what these callbacks do (and which versions they apply to).
cabc_config() in particular appears to have a very odd interface for wled4. It looks like it relies on being initially called with enable set a particular way and prevents itself from acting again. Therefore if the comment you end up writing doesn't sound "right" then please also fix the API!
Finally, why is everything except cabc_config() prefixed with wled?
Daniel.
Re: [PATCH V3 2/4] backlight: qcom-wled: Add callback functions
Quoted 12 lines · Daniel Thompson
Quoted 4 lines · Kiran Gunda
Add
cabc_config,sync_toggle,wled_ovp_fault_statusandwled_ovp_delaycallback functions to prepare the driver for adding WLED5 support.Signed-off-by Kiran Gunda <[email protected]>Overall this code would a lot easier to review if
Quoted 5 lines
--- drivers/video/backlight/qcom-wled.c | 196 +++++++++++++++++++++++------------- 1 file changed, 126 insertions(+), 70 deletions(-)
Quoted 12 lines
drivers/video/backlight/qcom-wled.c struct wled_config { · line 131
Quoted 9 lines
drivers/video/backlight/qcom-wled.c +1
-0@@ -128,6 +128,7 @@ struct wled_config {bool cs_out_en;bool ext_gen;bool cabc; +bool en_cabc;Does this ever get set to true?
Yes. If user wants use the cabc pin to control the brightness and use the "qcom,cabc" DT property in the device tree.
Quoted 14 lines
Quoted 14 lines
drivers/video/backlight/qcom-wled.c +2
-0bool external_pfet;bool auto_detection_enabled; };@@ -147,14 +148,20 @@ struct wled {u32 max_brightness;u32 short_count;u32 auto_detect_count; +u32 version;bool disabled_by_short;bool has_short_detect; +bool cabc_disabled;int short_irq;int ovp_irq;
Quoted 11 lines
drivers/video/backlight/qcom-wled.c struct wled { · line 164
Quoted 7 lines
drivers/video/backlight/qcom-wled.c +4
-0struct wled_config cfg;struct delayed_work ovp_work;int (*wled_set_brightness)(struct wled *wled,u16 brightness); +int (*cabc_config)(struct wled *wled,bool enable); +int (*wled_sync_toggle)(struct wled *wled); +int (*wled_ovp_fault_status)(struct wled *wled,bool *fault_set); +int (*wled_ovp_delay)(struct wled *wled);Let's get some doc comments explaining what these callbacks do (and which versions they apply to).
Sure. I will update it in the commit text in next post.
Quoted 6 lines
cabc_config()in particular appears to have a very odd interface for wled4. It looks like it relies on being initially called with enable set a particular way and prevents itself from acting again. Therefore if the comment you end up writing doesn't sound "right" then please also fix the API!
Actually this variable is useful for WLED5, where the default HW state is CABC1 enabled mode. So, if the user doesn't want to use the CABC we are configuring the HW state to "0" based on the DT property and then setting a flag to not enable it again. This is not needed for WLED4. I will remove it for WLED4 in next post.
Quoted 2 lines
Finally, why is everything except
cabc_config()prefixed with wled?
It is typo. I will correct it in the next post.
Quoted 2 lines
Daniel.
Re: [PATCH V3 2/4] backlight: qcom-wled: Add callback functions
Quoted 26 lines · On Wed, Mar 11, 2020 at 12:11:00PM +0530, [email protected] wrote:
Quoted 12 lines · Daniel Thompson
Quoted 4 lines · Kiran Gunda
Add
cabc_config,sync_toggle,wled_ovp_fault_statusandwled_ovp_delaycallback functions to prepare the driver for adding WLED5 support.Signed-off-by Kiran Gunda <[email protected]>Overall this code would a lot easier to review if
Quoted 5 lines
--- drivers/video/backlight/qcom-wled.c | 196 +++++++++++++++++++++++------------- 1 file changed, 126 insertions(+), 70 deletions(-)Quoted 13 lines
drivers/video/backlight/qcom-wled.c struct wled_config { · line 131
Quoted 10 lines
drivers/video/backlight/qcom-wled.c +1
-0@@ -128,6 +128,7 @@ struct wled_config {bool cs_out_en;bool ext_gen;bool cabc; +bool en_cabc;Does this ever get set to true?
Quoted 2 lines
Yes. If user wants use the cabc pin to control the brightness and use the "qcom,cabc" DT property in the device tree.
That sounds like what you intended the code to do!
Is the code that does this present in the patch? I could not find it.
Daniel.
Re: [PATCH V3 2/4] backlight: qcom-wled: Add callback functions
Quoted 27 lines · Daniel Thompson
Quoted 26 lines · On Wed, Mar 11, 2020 at 12:11:00PM +0530, [email protected] wrote:
Quoted 25 lines · Daniel Thompson
Quoted 4 lines · Kiran Gunda
Add
cabc_config,sync_toggle,wled_ovp_fault_statusandwled_ovp_delaycallback functions to prepare the driver for adding WLED5 support.Signed-off-by Kiran Gunda <[email protected]>Overall this code would a lot easier to review if
Quoted 11 lines
--- drivers/video/backlight/qcom-wled.c | 196 +++++++++++++++++++++++------------- 1 file changed, 126 insertions(+), 70 deletions(-)drivers/video/backlight/qcom-wled.c +0
-0drivers/video/backlight/qcom-wled.c struct wled_config { · line 131
Quoted 4 lines
drivers/video/backlight/qcom-wled.c +1
-0@@ -128,6 +128,7 @@ struct wled_config {bool cs_out_en;bool ext_gen;bool cabc; +bool en_cabc;Does this ever get set to true?
Quoted 8 lines
Quoted 2 lines
Yes. If user wants use the cabc pin to control the brightness and use the "qcom,cabc" DT property in the device tree.
That sounds like what you intended the code to do!
Is the code that does this present in the patch? I could not find it.
okay... It's my bad. We already have the "cabc" for this. I will remove the en_cabc in next series.
Quoted 2 lines
Daniel.
PATCH v3 3/4 backlight: qcom-wled: Add support for WLED5 peripheral in PM8150L
In reply to Kiran GundaAdd support for WLED5 peripheral that is present on PM8150L PMICs.
PM8150L WLED supports the following:
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options
- Multiple brightness width selection (12 bits to 15 bits)
--- .../bindings/leds/backlight/qcom-wled.yaml | 39 +++ drivers/video/backlight/qcom-wled.c | 336 ++++++++++++++++++++- 2 files changed, 374 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +39 -0
@@ -20,6 +20,7 @@ properties: - qcom,pm8941-wled - qcom,pmi8998-wled - qcom,pm660l-wled + - qcom,pm8150l-wled reg: maxItems: 1
@@ -28,10 +29,23 @@ properties: maxItems: 1 description: brightness value on boot, value from 0-4095. + For pm8150l this value vary from 0-4095 or 0-32767 + depending on the brightness control mode. If CABC is + enabled 0-4095 range is used. allOf: - $ref: /schemas/types.yaml#/definitions/uint32 default: 2048 + max-brightness: + maxItems: 1 + description: + Maximum brightness level. Allowed values are, + for pmi8998 it is 0-4095. + For pm8150l, this can be either 4095 or 32767. + If CABC is enabled, this is capped to 4095. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + label: maxItems: 1 description:
@@ -124,6 +138,31 @@ properties: value for PM8941 from 1 to 3. Default 2 For PMI8998 from 1 to 4. + qcom,modulator-sel: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selects the modulator used for brightness modulation. + Allowed values are, + 0 - Modulator A + 1 - Modulator B + If not specified, then modulator A will be used by default. + This property is applicable only to WLED5 peripheral. + + qcom,cabc-sel: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selects the CABC pin signal used for brightness modulation. + Allowed values are, + 0 - CABC disabled + 1 - CABC 1 + 2 - CABC 2 + 3 - External signal (e.g. LPG) is used for dimming + This property is applicable only to WLED5 peripheral. + interrupts: maxItems: 2 description:
drivers/video/backlight/qcom-wled.c +335 -1
444 lines not on this page · raw message
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH V3 3/4] backlight: qcom-wled: Add support for WLED5 peripheral in PM8150L
Quoted 8 lines · Kiran Gunda
Add support for WLED5 peripheral that is present on PM8150L PMICs.
PM8150L WLED supports the following:
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options
- Multiple brightness width selection (12 bits to 15 bits)Signed-off-by Kiran Gunda <[email protected]>
Mostly just style comments below...
Quoted 3 lines
--- .../bindings/leds/backlight/qcom-wled.yaml | 39 +++ drivers/video/backlight/qcom-wled.c | 336 ++++++++++++++++++++-
Shouldn't the bindings and driver be separate?
Quoted 15 lines
2 files changed, 374 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +1
-0@@ -20,6 +20,7 @@ properties: - qcom,pm8941-wled - qcom,pmi8998-wled - qcom,pm660l-wled + - qcom,pm8150l-wled reg: maxItems: 1
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml properties: · line 34
Quoted 6 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +3
-0@@ -28,10 +29,23 @@ properties: maxItems: 1 description: brightness value on boot, value from 0-4095. + For pm8150l this value vary from 0-4095 or 0-32767 + depending on the brightness control mode. If CABC is + enabled 0-4095 range is used.
Is this a pm8150l restriction or a WLED5 restriction (will other WLED5 have different ranges)?
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml properties: · line 44
Quoted 10 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +6
-0allOf: - $ref: /schemas/types.yaml#/definitions/uint32 default: 2048 + max-brightness: + maxItems: 1 + description: + Maximum brightness level. Allowed values are, + for pmi8998 it is 0-4095. + For pm8150l, this can be either 4095 or 32767.
Ditto.
Quoted 102 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +29
-0+ If CABC is enabled, this is capped to 4095. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + label: maxItems: 1 description:@@ -124,6 +138,31 @@ properties: value for PM8941 from 1 to 3. Default 2 For PMI8998 from 1 to 4. + qcom,modulator-sel: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selects the modulator used for brightness modulation. + Allowed values are, + 0 - Modulator A + 1 - Modulator B + If not specified, then modulator A will be used by default. + This property is applicable only to WLED5 peripheral. + + qcom,cabc-sel: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selects the CABC pin signal used for brightness modulation. + Allowed values are, + 0 - CABC disabled + 1 - CABC 1 + 2 - CABC 2 + 3 - External signal (e.g. LPG) is used for dimming + This property is applicable only to WLED5 peripheral. + interrupts: maxItems: 2 description:drivers/video/backlight/qcom-wled.c +37
-0@@ -19,6 +19,8 @@#define WLED_DEFAULT_BRIGHTNESS 2048#define WLED_SOFT_START_DLY_US 10000#define WLED3_SINK_REG_BRIGHT_MAX 0xFFF +#define WLED5_SINK_REG_BRIGHT_MAX_12B 0xFFF +#define WLED5_SINK_REG_BRIGHT_MAX_15B 0x7FFF/* WLED3/WLED4 control registers */ #define WLED3_CTRL_REG_FAULT_STATUS 0x08@@ -40,6 +42,7 @@#define WLED3_CTRL_REG_OVP 0x4d#define WLED3_CTRL_REG_OVP_MASK GENMASK(1, 0) +#define WLED5_CTRL_REG_OVP_MASK GENMASK(3, 0)#define WLED3_CTRL_REG_ILIMIT 0x4e#define WLED3_CTRL_REG_ILIMIT_MASK GENMASK(2, 0)@@ -101,6 +104,40 @@#define WLED4_SINK_REG_BRIGHT (n) (0x57 + (n * 0x10)) +/* WLED5 specific sink registers */ +#define WLED5_SINK_REG_MOD_A_EN 0x50 +#define WLED5_SINK_REG_MOD_B_EN 0x60 +#define WLED5_SINK_REG_MOD_EN_MASK BIT(7) + +#define WLED5_SINK_REG_MOD_A_SRC_SEL 0x51 +#define WLED5_SINK_REG_MOD_B_SRC_SEL 0x61 +#define WLED5_SINK_REG_MOD_SRC_SEL_HIGH 0 +#define WLED5_SINK_REG_MOD_SRC_SEL_EXT 0x03 +#define WLED5_SINK_REG_MOD_SRC_SEL_MASK GENMASK(1, 0) + +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL 0x52 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL 0x62 +#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B 0 +#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B 1 + +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB 0x53 +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB 0x54 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB 0x63 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB 0x64 + +#define WLED5_SINK_REG_MOD_SYNC_BIT 0x65 +#define WLED5_SINK_REG_SYNC_MOD_A_BIT BIT(0) +#define WLED5_SINK_REG_SYNC_MOD_B_BIT BIT(1) +#define WLED5_SINK_REG_SYNC_MASK GENMASK(1, 0) + +/* WLED5 specific per-'string' registers below */ +#define WLED5_SINK_REG_STR_FULL_SCALE_CURR (n) (0x72 + (n * 0x10)) + +#define WLED5_SINK_REG_STR_SRC_SEL (n) (0x73 + (n * 0x10)) +#define WLED5_SINK_REG_SRC_SEL_MOD_A 0 +#define WLED5_SINK_REG_SRC_SEL_MOD_B 1 +#define WLED5_SINK_REG_SRC_SEL_MASK GENMASK(1, 0) +struct wled_var_cfg {const u32 *values;u32 (*fn)(u32 );
drivers/video/backlight/qcom-wled.c struct wled_config { · line 167
Quoted 6 lines
drivers/video/backlight/qcom-wled.c +2
-0@@ -125,6 +162,8 @@ struct wled_config {u32 num_strings;u32 string_i_limit;u32 enabled_strings[WLED_MAX_STRINGS ]; +u32 mod_sel; +u32 cabc_sel;
Please explain cabc_sel (wled5) versus cabc_en (wled4).
Quoted 44 lines
drivers/video/backlight/qcom-wled.c +0
-0bool cs_out_en;bool ext_gen;drivers/video/backlight/qcom-wled.c +30
-0bool cabc;@@ -164,6 +203,27 @@ struct wled {int (*wled_ovp_delay)(struct wled *wled); }; +enum wled5_mod_sel { +MOD_A , +MOD_B , +MOD_MAX , +}; + +static const u8 wled5_brightness_reg[MOD_MAX ] = { + [MOD_A ] =WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB , + [MOD_B ] =WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB , +}; + +static const u8 wled5_src_sel_reg[MOD_MAX ] = { + [MOD_A ] =WLED5_SINK_REG_MOD_A_SRC_SEL , + [MOD_B ] =WLED5_SINK_REG_MOD_B_SRC_SEL , +}; + +static const u8 wled5_brt_wid_sel_reg[MOD_MAX ] = { + [MOD_A ] =WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL , + [MOD_B ] =WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL , +}; +static int wled3_set_brightness (struct wled *wled,u16 brightness) {int rc, i;@@ -182,6 +242,25 @@ static int wled3_set_brightness(struct wled *wled, u16 brightness)return 0 ; } +static int wled5_set_brightness (struct wled *wled,u16 brightness) +{ +int rc, offset; +u16 low_limit = wled->max_brightness *1 /1000 ; +u8 v[2 ]; + +/* WLED5's lower limit is 0.1% */ +if (brightness < low_limit) + brightness = low_limit;
drivers/video/backlight/qcom-wled.c static int wled3_set_brightness(struct wled *wled, u16 brightness) · line 263
Quoted 10 lines
drivers/video/backlight/qcom-wled.c +10
-0+ + v[0 ] = brightness &0xff ; + v[1 ] = (brightness >>8 ) &0x7f ; + + offset = wled5_brightness_reg[wled->cfg.mod_sel]; + rc =regmap_bulk_write (wled->regmap, wled->sink_addr + offset, + v,2 ); +return rc; +} +
Can we keep the same ordering throughout the file (wled3, wled4, wled5)? Most of the wled5 callbacks seem to have been inserted above wled4.
Daniel.
Re: [PATCH V3 3/4] backlight: qcom-wled: Add support for WLED5 peripheral in PM8150L
Quoted 13 lines · Daniel Thompson
Quoted 8 lines · Kiran Gunda
Add support for WLED5 peripheral that is present on PM8150L PMICs.
PM8150L WLED supports the following:
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options
- Multiple brightness width selection (12 bits to 15 bits)Signed-off-by Kiran Gunda <[email protected]>Mostly just style comments below...
Quoted 8 lines
Quoted 4 lines
--- .../bindings/leds/backlight/qcom-wled.yaml | 39 +++ drivers/video/backlight/qcom-wled.c | 336++++++++++++++++++++-
Shouldn't the bindings and driver be separate?
Ok. I will split it out in to a separate patch in next post.
Quoted 12 lines
Quoted 12 lines
2 files changed, 374 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +1
-0@@ -20,6 +20,7 @@ properties: - qcom,pm8941-wled - qcom,pmi8998-wled - qcom,pm660l-wled + - qcom,pm8150l-wled
Quoted 13 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml properties: · line 34
Quoted 9 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +3
-0reg: maxItems: 1@@ -28,10 +29,23 @@ properties: maxItems: 1 description: brightness value on boot, value from 0-4095. + For pm8150l this value vary from 0-4095 or 0-32767 + depending on the brightness control mode. If CABC is + enabled 0-4095 range is used.Is this a pm8150l restriction or a WLED5 restriction (will other WLED5 have different ranges)?
It is a WLED5 restriction which is used in pm8150l PMIC.
Quoted 5 lines
Quoted 5 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +0
-0allOf: - $ref: /schemas/types.yaml#/definitions/uint32 default: 2048
Quoted 9 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml properties: · line 44
Quoted 6 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +6
-0+ max-brightness: + maxItems: 1 + description: + Maximum brightness level. Allowed values are, + for pmi8998 it is 0-4095. + For pm8150l, this can be either 4095 or 32767.Ditto.
It is a WLED5 restriction which is used in pm8150l PMIC.
Quoted 107 lines
Quoted 106 lines
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml +29
-0+ If CABC is enabled, this is capped to 4095. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + label: maxItems: 1 description:@@ -124,6 +138,31 @@ properties: value for PM8941 from 1 to 3. Default 2 For PMI8998 from 1 to 4. + qcom,modulator-sel: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selects the modulator used for brightness modulation. + Allowed values are, + 0 - Modulator A + 1 - Modulator B + If not specified, then modulator A will be used by default. + This property is applicable only to WLED5 peripheral. + + qcom,cabc-sel: + maxItems: 1 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selects the CABC pin signal used for brightness modulation. + Allowed values are, + 0 - CABC disabled + 1 - CABC 1 + 2 - CABC 2 + 3 - External signal (e.g. LPG) is used for dimming + This property is applicable only to WLED5 peripheral. + interrupts: maxItems: 2 description:drivers/video/backlight/qcom-wled.c +37
-0@@ -19,6 +19,8 @@#define WLED_DEFAULT_BRIGHTNESS 2048#define WLED_SOFT_START_DLY_US 10000#define WLED3_SINK_REG_BRIGHT_MAX 0xFFF +#define WLED5_SINK_REG_BRIGHT_MAX_12B 0xFFF +#define WLED5_SINK_REG_BRIGHT_MAX_15B 0x7FFF/* WLED3/WLED4 control registers */ #define WLED3_CTRL_REG_FAULT_STATUS 0x08@@ -40,6 +42,7 @@#define WLED3_CTRL_REG_OVP 0x4d#define WLED3_CTRL_REG_OVP_MASK GENMASK(1, 0) +#define WLED5_CTRL_REG_OVP_MASK GENMASK(3, 0)#define WLED3_CTRL_REG_ILIMIT 0x4e#define WLED3_CTRL_REG_ILIMIT_MASK GENMASK(2, 0)@@ -101,6 +104,40 @@#define WLED4_SINK_REG_BRIGHT (n) (0x57 + (n * 0x10)) +/* WLED5 specific sink registers */ +#define WLED5_SINK_REG_MOD_A_EN 0x50 +#define WLED5_SINK_REG_MOD_B_EN 0x60 +#define WLED5_SINK_REG_MOD_EN_MASK BIT(7) + +#define WLED5_SINK_REG_MOD_A_SRC_SEL 0x51 +#define WLED5_SINK_REG_MOD_B_SRC_SEL 0x61 +#define WLED5_SINK_REG_MOD_SRC_SEL_HIGH 0 +#define WLED5_SINK_REG_MOD_SRC_SEL_EXT 0x03 +#define WLED5_SINK_REG_MOD_SRC_SEL_MASK GENMASK(1, 0) + +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL 0x52 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL 0x62 +#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B 0 +#define WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B 1 + +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB 0x53 +#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB 0x54 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB 0x63 +#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB 0x64 + +#define WLED5_SINK_REG_MOD_SYNC_BIT 0x65 +#define WLED5_SINK_REG_SYNC_MOD_A_BIT BIT(0) +#define WLED5_SINK_REG_SYNC_MOD_B_BIT BIT(1) +#define WLED5_SINK_REG_SYNC_MASK GENMASK(1, 0) + +/* WLED5 specific per-'string' registers below */ +#define WLED5_SINK_REG_STR_FULL_SCALE_CURR (n) (0x72 + (n * 0x10)) + +#define WLED5_SINK_REG_STR_SRC_SEL (n) (0x73 + (n * 0x10)) +#define WLED5_SINK_REG_SRC_SEL_MOD_A 0 +#define WLED5_SINK_REG_SRC_SEL_MOD_B 1 +#define WLED5_SINK_REG_SRC_SEL_MASK GENMASK(1, 0) +struct wled_var_cfg {const u32 *values;u32 (*fn)(u32 );@@ -125,6 +162,8 @@ struct wled_config {u32 num_strings;u32 string_i_limit;u32 enabled_strings[WLED_MAX_STRINGS ];
Quoted 5 lines
drivers/video/backlight/qcom-wled.c struct wled_config { · line 166
Quoted 2 lines
drivers/video/backlight/qcom-wled.c +2
-0+u32 mod_sel; +u32 cabc_sel;Please explain
cabc_sel(wled5) versuscabc_en(wled4).
Ok. WLED5 has 2 CABC modules, from which one can be selected/enabled. wled4 has only one CABC module and it is just enabled based on the user input. I will add a comment in next post.
Quoted 50 lines
Quoted 50 lines
drivers/video/backlight/qcom-wled.c +35
-0bool cs_out_en;bool ext_gen;bool cabc;@@ -164,6 +203,27 @@ struct wled {int (*wled_ovp_delay)(struct wled *wled); }; +enum wled5_mod_sel { +MOD_A , +MOD_B , +MOD_MAX , +}; + +static const u8 wled5_brightness_reg[MOD_MAX ] = { + [MOD_A ] =WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB , + [MOD_B ] =WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB , +}; + +static const u8 wled5_src_sel_reg[MOD_MAX ] = { + [MOD_A ] =WLED5_SINK_REG_MOD_A_SRC_SEL , + [MOD_B ] =WLED5_SINK_REG_MOD_B_SRC_SEL , +}; + +static const u8 wled5_brt_wid_sel_reg[MOD_MAX ] = { + [MOD_A ] =WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL , + [MOD_B ] =WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL , +}; +static int wled3_set_brightness (struct wled *wled,u16 brightness) {int rc, i;@@ -182,6 +242,25 @@ static int wled3_set_brightness(struct wled *wled, u16 brightness)return 0 ; } +static int wled5_set_brightness (struct wled *wled,u16 brightness) +{ +int rc, offset; +u16 low_limit = wled->max_brightness *1 /1000 ; +u8 v[2 ]; + +/* WLED5's lower limit is 0.1% */ +if (brightness < low_limit) + brightness = low_limit; + + v[0 ] = brightness &0xff ; + v[1 ] = (brightness >>8 ) &0x7f ; + + offset = wled5_brightness_reg[wled->cfg.mod_sel];
Quoted 9 lines
drivers/video/backlight/qcom-wled.c static int wled3_set_brightness(struct wled *wled, u16 brightness) · line 263
Quoted 5 lines
drivers/video/backlight/qcom-wled.c +5
-0+ rc =regmap_bulk_write (wled->regmap, wled->sink_addr + offset, + v,2 ); +return rc; +} +Can we keep the same ordering throughout the file (wled3, wled4, wled5)? Most of the wled5 callbacks seem to have been inserted above wled4.
Sure. Will do it in next post.
Quoted 2 lines
Daniel.
PATCH v3 4/4 backlight: qcom-wled: Update auto calibration support for WLED5
In reply to Kiran GundaCurrently, auto calibration logic checks only for OVP_FAULT bit to be set in FAULT_STATUS register to detect OVP fault. This works well for WLED4 type. However, WLED5 type has OVP_PRE_ALARM bit which can indicate a potential OVP fault. Use that as well for detecting OVP fault and run auto calibration to fix the sink configuration.
--- drivers/video/backlight/qcom-wled.c | 90 ++++++++++++++++++++++++++++++++++++- 1 file changed, 88 insertions(+), 2 deletions(-)
drivers/video/backlight/qcom-wled.c +88 -2
@@ -27,6 +27,7 @@#define WLED3_CTRL_REG_ILIM_FAULT_BIT BIT(0)#define WLED3_CTRL_REG_OVP_FAULT_BIT BIT(1)#define WLED4_CTRL_REG_SC_FAULT_BIT BIT(2) +#define WLED5_CTRL_REG_OVP_PRE_ALARM_BIT BIT(4)#define WLED3_CTRL_REG_INT_RT_STS 0x10#define WLED3_CTRL_REG_OVP_FAULT_STATUS BIT(1)
@@ -104,6 +105,10 @@#define WLED4_SINK_REG_BRIGHT (n) (0x57 + (n * 0x10)) +/* WLED5 specific control registers */ +#define WLED5_CTRL_REG_OVP_INT_CTL 0x5f +#define WLED5_CTRL_REG_OVP_INT_TIMER_MASK GENMASK(2, 0) +/* WLED5 specific sink registers */ #define WLED5_SINK_REG_MOD_A_EN 0x50#define WLED5_SINK_REG_MOD_B_EN 0x60
@@ -394,11 +399,67 @@ static int wled4_ovp_fault_status(struct wled *wled, bool *fault_set)return rc; } +static int wled5_ovp_fault_status (struct wled *wled,bool *fault_set) +{ +int rc; +u32 int_rt_sts, fault_sts; + + *fault_set = false; + rc =regmap_read (wled->regmap, + wled->ctrl_addr +WLED3_CTRL_REG_INT_RT_STS , + &int_rt_sts); +if (rc <0 ) { +dev_err (wled->dev,"Failed to read INT_RT_STS rc=%d\n" , rc); +return rc; + } + + rc =regmap_read (wled->regmap, + wled->ctrl_addr +WLED3_CTRL_REG_FAULT_STATUS , + &fault_sts); +if (rc <0 ) { +dev_err (wled->dev,"Failed to read FAULT_STATUS rc=%d\n" , rc); +return rc; + } + +if (int_rt_sts &WLED3_CTRL_REG_OVP_FAULT_STATUS ) + *fault_set = true; + +if (fault_sts & (WLED3_CTRL_REG_OVP_FAULT_BIT | +WLED5_CTRL_REG_OVP_PRE_ALARM_BIT )) + *fault_set = true; + +if (*fault_set) +dev_dbg (wled->dev,"WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n" , + int_rt_sts, fault_sts); + +return rc; +} +static int wled4_ovp_delay (struct wled *wled) {return WLED_SOFT_START_DLY_US ; } +static int wled5_ovp_delay (struct wled *wled) +{ +int rc, delay_us; +u32 val; +u8 ovp_timer_ms[8 ] = {1 ,2 ,4 ,8 ,12 ,16 ,20 ,24 }; + +/* For WLED5, get the delay based on OVP timer */ + rc =regmap_read (wled->regmap, wled->ctrl_addr + +WLED5_CTRL_REG_OVP_INT_CTL , &val); +if (rc <0 ) + delay_us = + ovp_timer_ms[val &WLED5_CTRL_REG_OVP_INT_TIMER_MASK ] *1000 ; +else + delay_us =2 *WLED_SOFT_START_DLY_US ; + +dev_dbg (wled->dev,"delay_time_us: %d\n" , *delay_us); + +return delay_us; +} +static int wled_update_status (struct backlight_device *bl) {struct wled *wled =bl_get_data (bl);
@@ -736,9 +797,32 @@ static bool wled_auto_detection_required(struct wled *wled)if (!wled->auto_detection_ovp_count) { wled->start_ovp_fault_time =ktime_get (); wled->auto_detection_ovp_count++; - }else { +return false; + } + +if (wled->version ==5 ) { +/* +* WLED5 has OVP fault density interrupt configuration i.e. to +* count the number of OVP alarms for a certain duration before +* triggering OVP fault interrupt. By default, number of OVP +* fault events counted before an interrupt is fired is 32 and +* the time interval is 12 ms. If we see more than one OVP fault +* interrupt, then that should qualify for a real OVP fault +* condition to run auto calibration algorithm. +*/ + +if (wled->auto_detection_ovp_count >1 ) { + elapsed_time_us =ktime_us_delta (ktime_get (), + wled->start_ovp_fault_time); + wled->auto_detection_ovp_count =0 ; +dev_dbg (wled->dev,"Elapsed time: %lld us\n" , + elapsed_time_us); +return true; + } + wled->auto_detection_ovp_count++; + }else if (wled->version ==4 ) { elapsed_time_us =ktime_us_delta (ktime_get (), - wled->start_ovp_fault_time); + wled->start_ovp_fault_time);if (elapsed_time_us >WLED_AUTO_DETECT_CNT_DLY_US ) wled->auto_detection_ovp_count =0 ;else
@@ -1424,6 +1508,8 @@ static int wled_configure(struct wled *wled) wled->wled_set_brightness = wled5_set_brightness; wled->wled_sync_toggle = wled5_sync_toggle; wled->cabc_config = wled5_cabc_config; + wled->wled_ovp_fault_status = wled5_ovp_fault_status; + wled->wled_ovp_delay = wled5_ovp_delay; wled->max_string_count =4 ; prop_addr =of_get_address (dev->of_node,1 ,NULL ,NULL );
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project