further mt7988 devicetree work
Subsystems (7)
v7 cover further mt7988 devicetree work
From: Frank Wunderlich <[email protected]>
Sorry messed up the rebase in v6 somehow.
This series continues mt7988 devicetree work
- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)
depencies (i hope this list is complete and latest patches/series linked):
support interrupt-names is optional again as i re-added the reserved IRQs (they are not unusable as i thought and can allow features in future)
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
needs change in mtk ethernet driver for the sram to be read from separate node:
https://patchwork.kernel.org/project/netdevbpf/patch/566ca90fc59ad0d3aff8bc8dc22ebaf0544bce47.1751072868.git.daniel@makrotopia.org/
for SFP-Function (macs currently disabled):
PCS clearance which is a 1.5 year discussion currently ongoing
Daniel asked netdev for a way 2 go:
https://lore.kernel.org/netdev/[email protected]/
e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/
full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/
first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/
some more here:
https://lore.kernel.org/netdev/[email protected]/
and then dts nodes for sgmiisys+usxgmii+2g5 firmware
when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.
changes:
v7:
- squashed first 2 v6 patches as they should to have interrupt-names and mt7988 parts separated
v6:
binding:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- move interrupt-names up
- add sram-property
- drop second reg entry and minitems as there is only 1 item left
dts:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)
v5:
- add reserved irqs and change names
- update binding for 8 irqs with different names (rx,tx => fe1+fe2, rx-ringX => pdmaX) (dropped Robs RB due to this change again, sorry)
v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)
dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
v3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliases
v2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsi
Frank Wunderlich (14):
dt-bindings: net: mediatek,net: allow irq names
dt-bindings: net: mediatek,net: update for mt7988
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for
mt7988
dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
dt-bindings: interconnect: add mt7988-cci compatible
arm64: dts: mediatek: mt7988: add cci node
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds
.../bindings/interconnect/mediatek,cci.yaml | 11 +- .../bindings/net/dsa/mediatek,mt7530.yaml | 24 +- .../devicetree/bindings/net/mediatek,net.yaml | 47 ++- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 + .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 ++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 198 ++++++----- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 318 +++++++++++++++++- 7 files changed, 529 insertions(+), 99 deletions(-)
Signature · 1 line
2.43.0
PATCH v7 1/14 dt-bindings: net: mediatek,net: allow irq names
From: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names property. Also increase the maximum IRQ count to 8 (4 FE + 4 RSS), but set boundaries for all compatibles same as irq count.
---
v7: fixed wrong rebase
v6: new patch splitted from the mt7988 changes
--- .../devicetree/bindings/net/mediatek,net.yaml | 38 ++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +37 -1
@@ -40,7 +40,19 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: fe0 + - const: fe1 + - const: fe2 + - const: fe3 + - const: pdma0 + - const: pdma1 + - const: pdma2 + - const: pdma3 power-domains: maxItems: 1
@@ -135,6 +147,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 4 maxItems: 4
@@ -166,6 +182,9 @@ allOf: interrupts: maxItems: 1 + interrupt-namess: + maxItems: 1 + clocks: minItems: 2 maxItems: 2
@@ -192,6 +211,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 11 maxItems: 11
@@ -232,6 +255,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 17 maxItems: 17
@@ -274,6 +301,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15
@@ -312,6 +342,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15
@@ -350,6 +383,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 24 maxItems: 24
Signature · 1 line
2.43.0
Re: [PATCH v7 01/14] dt-bindings: net: mediatek,net: allow irq names
Quoted 3 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names
Why? What preparation, what is the purpose of adding the names, what do they solve?
Quoted 1 line
property. Also increase the maximum IRQ count to 8 (4 FE + 4 RSS),
Why? There is no user of 8 items.
Quoted 1 line
but set boundaries for all compatibles same as irq count.
Your patch does not do it.
Quoted 88 lines
Signed-off-by Frank Wunderlich <[email protected]>---
v7: fixed wrong rebase
v6: new patch splitted from the mt7988 changes--- .../devicetree/bindings/net/mediatek,net.yaml | 38 ++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +31
-1@@ -40,7 +40,19 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: fe0 + - const: fe1 + - const: fe2 + - const: fe3 + - const: pdma0 + - const: pdma1 + - const: pdma2 + - const: pdma3 power-domains: maxItems: 1@@ -135,6 +147,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 4 maxItems: 4@@ -166,6 +182,9 @@ allOf: interrupts: maxItems: 1 + interrupt-namess: + maxItems: 1 + clocks: minItems: 2 maxItems: 2@@ -192,6 +211,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 11 maxItems: 11@@ -232,6 +255,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 17 maxItems: 17@@ -274,6 +301,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 346
Quoted 5 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0@@ -312,6 +342,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4
8 interrupts is now valid?
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 387
Quoted 10 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +3
-0+ clocks: minItems: 15 maxItems: 15@@ -350,6 +383,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4
So why sudenly this device gets 8 interrupts? This makes no sense, nothing explained in the commit msg.
I understand nothing from this patch and I already asked you to clearly explain why you are doing things. This patch on its own makes no sense.
Best regards,
Krzysztof
Re: [PATCH v7 01/14] dt-bindings: net: mediatek,net: allow irq names
Am 1. Juli 2025 08:44:02 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 7 lines · Frank Wunderlich
Quoted 3 lines
From: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names
Why? What preparation, what is the purpose of adding the names, what do they solve?
Devicetree handled by the mtk_eth_soc driver have a wild mix of shared and non-shared irq definitions accessed by index (shared use index 0, non-shared
using 1+2). Some soc have only 3 FE irqs (like mt7622).
This makes it unclear which irq is used for what on which SoC. Adding names for irq cleans this a bit in device tree and driver.
Quoted 3 lines
Quoted 1 line
property. Also increase the maximum IRQ count to 8 (4 FE + 4 RSS),
Why? There is no user of 8 items.
MT7988 *with* RSS/LRO (not yet supported by driver yet,but i add the irqs in devicetree in this series) use 8 irqs,but RSS is optional and 4 irqs get working ethernet stack.
I hope this explanation makes things clearer...
Quoted 3 lines
Quoted 1 line
but set boundaries for all compatibles same as irq count.
Your patch does not do it.
I set Min/max-items for interrupt names below like interrupts count defined.
Quoted 104 lines
Quoted 88 lines
Signed-off-by Frank Wunderlich <[email protected]>---
v7: fixed wrong rebase
v6: new patch splitted from the mt7988 changes--- .../devicetree/bindings/net/mediatek,net.yaml | 38 ++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +31
-1@@ -40,7 +40,19 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: fe0 + - const: fe1 + - const: fe2 + - const: fe3 + - const: pdma0 + - const: pdma1 + - const: pdma2 + - const: pdma3 power-domains: maxItems: 1@@ -135,6 +147,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 4 maxItems: 4@@ -166,6 +182,9 @@ allOf: interrupts: maxItems: 1 + interrupt-namess: + maxItems: 1 + clocks: minItems: 2 maxItems: 2@@ -192,6 +211,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 11 maxItems: 11@@ -232,6 +255,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 17 maxItems: 17@@ -274,6 +301,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 346
Quoted 5 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0@@ -312,6 +342,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 48 interrupts is now valid?
Quoted 8 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +1
-0+ clocks: minItems: 15 maxItems: 15@@ -350,6 +383,9 @@ allOf: interrupts: minItems: 4
Quoted 5 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 387
Quoted 2 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0+ interrupt-names: + minItems: 4So why sudenly this device gets 8 interrupts? This makes no sense, nothing explained in the commit msg.
4 FrameEngine IRQs are required to be defined (currently 2 are used in driver). The other 4 are optional,but added in the devicetree
to not run into problems supporting old devicetree
when adding RSS/LRO to driver.
Quoted 6 lines
I understand nothing from this patch and I already asked you to clearly explain why you are doing things. This patch on its own makes no sense.
Best regards,
Krzysztof
regards Frank
Re: [PATCH v7 01/14] dt-bindings: net: mediatek,net: allow irq names
Quoted 15 lines · Frank Wunderlich
Am 1. Juli 2025 08:44:02 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 7 lines · Frank Wunderlich
Quoted 3 lines
From: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names
Why? What preparation, what is the purpose of adding the names, what do they solve?
Devicetree handled by the
mtk_eth_socdriver have a wild mix of shared and non-shared irq definitions accessed by index (shared use index 0, non-shared
using 1+2). Some soc have only 3 FE irqs (like mt7622).
Quoted 3 lines
This makes it unclear which irq is used for what on which SoC. Adding names for irq cleans this a bit in device tree and driver.
It's implied ABI now, even if the binding did not express that. But interrupt-names are not necessary to express that at all. Look at other
bindings: we express the list by describing the items:
items:
- description: foo
- ... bar
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
property. Also increase the maximum IRQ count to 8 (4 FE + 4 RSS),
Why? There is no user of 8 items.
MT7988 *with* RSS/LRO (not yet supported by driver yet,but i add the irqs in devicetree in this series) use 8 irqs,but RSS is optional and 4 irqs get working ethernet stack.
That's separate change than fixing ABI and that user MUST BE HERE. You cannot add some future interrupts for some future device. Adding new device is the only reason to add more interrupts.
Quoted 2 lines
I hope this explanation makes things clearer...
Commit msg must explain all this, not me asking.
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
but set boundaries for all compatibles same as irq count.
Your patch does not do it.
I set Min/max-items for interrupt names below like interrupts count defined.
No, you don't. It's all fluid and flexible - limited constraints.
Quoted 105 lines
Quoted 105 lines
Quoted 89 lines
Signed-off-by Frank Wunderlich <[email protected]>---
v7: fixed wrong rebase
v6: new patch splitted from the mt7988 changes--- .../devicetree/bindings/net/mediatek,net.yaml | 38 ++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +31
-1@@ -40,7 +40,19 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: fe0 + - const: fe1 + - const: fe2 + - const: fe3 + - const: pdma0 + - const: pdma1 + - const: pdma2 + - const: pdma3 power-domains: maxItems: 1@@ -135,6 +147,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 4 maxItems: 4@@ -166,6 +182,9 @@ allOf: interrupts: maxItems: 1 + interrupt-namess: + maxItems: 1 + clocks: minItems: 2 maxItems: 2@@ -192,6 +211,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 11 maxItems: 11@@ -232,6 +255,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 17 maxItems: 17@@ -274,6 +301,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 346
Quoted 5 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0@@ -312,6 +342,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 48 interrupts is now valid?
Quoted 8 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +1
-0+ clocks: minItems: 15 maxItems: 15@@ -350,6 +383,9 @@ allOf: interrupts: minItems: 4
Quoted 8 lines
Quoted 5 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 387
Quoted 2 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0+ interrupt-names: + minItems: 4So why sudenly this device gets 8 interrupts? This makes no sense, nothing explained in the commit msg.
4 FrameEngine IRQs are required to be defined (currently 2 are used in driver). The other 4 are optional,but added in the devicetree
There were only 4 before and you do not explain why all devices get 8. You mentioned that MT7988 has 8 but now make 8 for all other variants!
Why you are not answering this question?
Quoted 2 lines
to not run into problems supporting old devicetree when adding RSS/LRO to driver.
This is not about driver, it does not matter for the driver. Binding and DTS are supposed to be complete.
Quoted 10 lines
Quoted 7 lines
I understand nothing from this patch and I already asked you to clearly explain why you are doing things. This patch on its own makes no sense.
Best regards,
Krzysztofregards Frank
Best regards,
Krzysztof
Re: [PATCH v7 01/14] dt-bindings: net: mediatek,net: allow irq names
Am 2025-07-02 08:27, schrieb Krzysztof Kozlowski:
Quoted 20 lines · Frank Wunderlich
Quoted 15 lines
Am 1. Juli 2025 08:44:02 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 7 lines · Frank Wunderlich
Quoted 3 lines
From: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names
Why? What preparation, what is the purpose of adding the names, what do they solve?
Devicetree handled by the
mtk_eth_socdriver have a wild mix of shared and non-shared irq definitions accessed by index (shared use index 0, non-shared
using 1+2). Some soc have only 3 FE irqs (like mt7622).Quoted 3 lines
This makes it unclear which irq is used for what on which SoC. Adding names for irq cleans this a bit in device tree and driver.
Quoted 6 lines
It's implied ABI now, even if the binding did not express that. But interrupt-names are not necessary to express that at all. Look at other
bindings: we express the list by describing the items:
items:
- description: foo
- ... bar
ok, so i need to define descriptions for all interrupts instead of only increasing the count. Ok, was not clear to me.
so something like this:
item0: on SoCs with shared IRQ (mt762[18]) used for RX+TX, on other free to be used
item1: on non-shared SoCs used for TX
item2: on non-shared SoCs used for RX (except RSS/LRO is used)
item3: reserved / currently unused
item4-7: IRQs for RSS/LRO
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
Quoted 2 lines
property. Also increase the maximum IRQ count to 8 (4 FE + 4 RSS),
Why? There is no user of 8 items.
Quoted 8 lines
Quoted 4 lines
MT7988 *with* RSS/LRO (not yet supported by driver yet,but i add the irqs in devicetree in this series) use 8 irqs,but RSS is optional and 4 irqs get working ethernet stack.
That's separate change than fixing ABI and that user MUST BE HERE. You cannot add some future interrupts for some future device. Adding new device is the only reason to add more interrupts.
MT7988 is basicly new because there is no devicetree there yet...only driver and this (incomplete) binding.
Quoted 7 lines
Quoted 2 lines
I hope this explanation makes things clearer...
Commit msg must explain all this, not me asking.
Quoted 1 line
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
but set boundaries for all compatibles same as irq count.
Your patch does not do it.
I set Min/max-items for interrupt names below like interrupts count defined.
No, you don't. It's all fluid and flexible - limited constraints.
i thought i can limit is by setting the MaxItems in the soc-spcific blocks below. What reason does MaxItems have there if not this? of course if there is any Soc not having a specific block it is open.But this is also the case for interrupts property handles the same way before.
I only left it open on mt7988 (only set minitems because all 8 can be used, but 4 are required).
Quoted 40 lines
Quoted 40 lines
Quoted 40 lines
Quoted 40 lines
Signed-off-by Frank Wunderlich <[email protected]>---
v7: fixed wrong rebase
v6: new patch splitted from the mt7988 changes--- .../devicetree/bindings/net/mediatek,net.yaml | 38 ++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +13
-1@@ -40,7 +40,19 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: fe0 + - const: fe1 + - const: fe2 + - const: fe3 + - const: pdma0 + - const: pdma1 + - const: pdma2 + - const: pdma3 power-domains: maxItems: 1@@ -135,6 +147,10 @@ allOf: minItems: 3 maxItems: 3
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 152
Quoted 3 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +3
-0+ interrupt-names: + minItems: 3 + maxItems: 3
limited here to the same as interrupts.
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 186
Quoted 9 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0clocks: minItems: 4 maxItems: 4@@ -166,6 +182,9 @@ allOf: interrupts: maxItems: 1 + interrupt-namess: + maxItems: 1
dito
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 216
Quoted 10 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +3
-0clocks: minItems: 2 maxItems: 2@@ -192,6 +211,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3
dito and so on
Quoted 47 lines
Quoted 47 lines
Quoted 46 lines
Quoted 25 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +7
-0clocks: minItems: 11 maxItems: 11@@ -232,6 +255,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 17 maxItems: 17@@ -274,6 +301,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 346
Quoted 5 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-0@@ -312,6 +342,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 48 interrupts is now valid?
Documentation/devicetree/bindings/net/mediatek,net.yaml allOf: · line 387
Quoted 10 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +3
-0+ clocks: minItems: 15 maxItems: 15@@ -350,6 +383,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4So why sudenly this device gets 8 interrupts? This makes no sense, nothing explained in the commit msg.
Quoted 7 lines
Quoted 2 lines
4 FrameEngine IRQs are required to be defined (currently 2 are used in driver). The other 4 are optional,but added in the devicetree
There were only 4 before and you do not explain why all devices get 8. You mentioned that MT7988 has 8 but now make 8 for all other variants!
Why you are not answering this question?
The original binding excluded the 4 RSS/LRO IRQs as this is an optional feature not yet available in driver. It is needed to get the full speed on the 10G interfaces. MT7988 is the first SoC which has 10G MACs. Older Socs like mt7986 and mt7981 can also support RSS/LRO to reduce cpu load. But here we will run into the "new kernel - old devicetree" issue, if we try to upstream this. Maybe we do not add this because these only have 2.5G MACs.
Quoted 5 lines
Quoted 2 lines
to not run into problems supporting old devicetree when adding RSS/LRO to driver.
This is not about driver, it does not matter for the driver. Binding and DTS are supposed to be complete.
if i upstream the ethernet-node now with only 4 IRQS, we have to extend them later and have to deal with only 4 IRQs in driver to be compatible with older DTS. So newer kernel with RSS/LRO support cannot work with older DT.
To avoid this i add all related IRQs now (from DT perspective a new device - there is no mt7988 device with ethernet node in devicetree yet).
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
I understand nothing from this patch and I already asked you to clearly explain why you are doing things. This patch on its own makes no sense.
i tried to explain :(
i have a working dts for mt7988 and try to upstream it in this series and thats the cause i have to update the binding. Imho i cannot increase the interrupt-count in SoC specific block (e.g. setting count globally to 4 but to 8 for only mt7988).
I added interrupt-names to get it cleaner in driver (access via name instead of index). And also in Devicetree we see the meaning of IRQs without looking through driver. I see really no reason for not adding the interrupt names.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Best regards,
Krzysztof
regards Frank
Re: [PATCH v7 01/14] dt-bindings: net: mediatek,net: allow irq names
Quoted 33 lines · Frank Wunderlich (linux)
Am 2025-07-02 08:27, schrieb Krzysztof Kozlowski:
Quoted 22 lines · Frank Wunderlich
Quoted 17 lines
Am 1. Juli 2025 08:44:02 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 8 lines · Frank Wunderlich
Quoted 3 lines
From: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names
Why? What preparation, what is the purpose of adding the names, what do
they solve?Devicetree handled by the
mtk_eth_socdriver have a wild mix of shared and non-shared irq definitions accessed by index (shared use index 0, non-shared
using 1+2). Some soc have only 3 FE irqs (like mt7622).Quoted 3 lines
This makes it unclear which irq is used for what on which SoC. Adding names for irq cleans this a bit in device tree and driver.
Quoted 6 lines
It's implied ABI now, even if the binding did not express that. But interrupt-names are not necessary to express that at all. Look at other
bindings: we express the list by describing the items:
items:
- description: foo
- ... barok, so i need to define descriptions for all interrupts instead of only increasing the count. Ok, was not clear to me.
Quoted 8 lines
so something like this:
item0: on SoCs with shared IRQ (mt762[18]) used for RX+TX, on other free to be used
item1: on non-shared SoCs used for TX
item2: on non-shared SoCs used for RX (except RSS/LRO is used)
item3: reserved / currently unused
item4-7: IRQs for RSS/LRO
These descriptions match the current *software* use of those interrupts, however, DT should describe the hardware and esp. item0 up to item3 could be used in different ways in the future (by programming MTK_FE_INT_GRP register differently).
I think using interrupt-names fe0...fe3 and pdma0...pdma3 is still the best option, so the driver can request the interrupts by name which is much more readable in the driver code and SoC's dtsi than relying on a specific order.
Quoted 6 lines
Quoted 5 lines
There were only 4 before and you do not explain why all devices get 8. You mentioned that MT7988 has 8 but now make 8 for all other variants!
Why you are not answering this question?
Quoted 11 lines
The original binding excluded the 4 RSS/LRO IRQs as this is an optional feature not
yet available in driver. It is needed to get the full speed on the 10G interfaces.
MT7988 is the first SoC which has 10G MACs. Older Socs like mt7986 and mt7981 can also
support RSS/LRO to reduce cpu load. But here we will run into the "new kernel - old
devicetree" issue, if we try to upstream this. Maybe we do not add this because these
only have 2.5G MACs.
It might be important to note that
MT7621, MT7628: 1 IRQ
MT7622, MT7623: 3 IRQs (only two used by the driver for now) MT7981, MT7986: 4 IRQs (only two used by the driver for now)
While older SoCs MT7981 and MT7986 have limited support for *either LRO or RSS* in hardware, only MT7988 got 4 frame-engine IRQs like MT7981 and MT7986 and an additional 4 IRQs for the 4 RX DMA rings on top of that, so a total of 8, and can do both RSS and LRO.
PATCH v7 2/14 dt-bindings: net: mediatek,net: update for mt7988
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
MT7988 has 4 FE IRQs (currently only 2 are used) and 4 IRQs for use with RSS/LRO later.
---
v6:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- add sram-property
- drop second reg entry and minitems as there is only 1 item left again
v5:
- fix v4 logmessage and change description a bit describing how i get the irq count.
- update binding for 8 irqs with different names (rx,tx => fe0..fe3) including the 2 reserved irqs which can be used later
- change rx-ringX to pdmaX to be closer to hardware documentation
v4:
- increase max interrupts to 6 because of adding RSS/LRO interrupts (4) and dropping 2 reserved irqs (0+3) around rx+tx
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988
this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
v2:
- change reg to list of items
--- Documentation/devicetree/bindings/net/mediatek,net.yaml | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +7 -2
@@ -28,7 +28,8 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs. clocks: minItems: 2
@@ -66,6 +67,10 @@ properties: - const: gmac - const: ppe + sram: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to mmio SRAM + mediatek,ethsys: $ref: /schemas/types.yaml#/definitions/phandle description:
@@ -418,7 +423,7 @@ allOf: - const: xgp3 patternProperties: - "^mac@[0-1]$": + "^mac@[0-2]$": type: object unevaluatedProperties: false allOf:
Signature · 1 line
2.43.0
Re: [PATCH v7 02/14] dt-bindings: net: mediatek,net: update for mt7988
Quoted 4 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
I asked why you are updating. You claim you update because it has 3 GMAC... but that's irrelevant, because it is easy to answer with: it did not have 3 GMAC before?
So same question: Provide real reason why you are making updates. That's why you have commit msg.
Quoted 2 lines
MT7988 has 4 FE IRQs (currently only 2 are used) and 4 IRQs for use
mt7988 or MT7988? gmac or GMAC? SRAM or SRAM? and so on... it is not easy to read and understand your commit msgs.
Quoted 37 lines
with RSS/LRO later.
Signed-off-by Frank Wunderlich <[email protected]>---
v6:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- add sram-property
- drop second reg entry and minitems as there is only 1 item left againv5:
- fix v4 logmessage and change description a bit describing how i get the irq count.
- update binding for 8 irqs with different names (rx,tx => fe0..fe3) including the 2 reserved irqs which can be used later
- change rx-ringX to pdmaX to be closer to hardware documentationv4:
- increase max interrupts to 6 because of adding RSS/LRO interrupts (4) and dropping 2 reserved irqs (0+3) around rx+tx
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988
this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/v2:
- change reg to list of items--- Documentation/devicetree/bindings/net/mediatek,net.yaml | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +0
-0
Documentation/devicetree/bindings/net/mediatek,net.yaml properties: · line 32
Quoted 6 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-1@@ -28,7 +28,8 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs.
Why making this change? It's redundant and nothing in commit msg explains that.
Best regards,
Krzysztof
Re: [PATCH v7 02/14] dt-bindings: net: mediatek,net: update for mt7988
Am 1. Juli 2025 08:41:42 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 6 lines · Frank Wunderlich
Quoted 4 lines
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
Quoted 6 lines
I asked why you are updating. You claim you update because it has 3 GMAC... but that's irrelevant, because it is easy to answer with: it did not have 3 GMAC before?
So same question: Provide real reason why you are making updates. That's why you have commit msg.
MT7988 had always 3 gmac,but no dts with ethernet node till now.
As i try to upstream the dts,i fell over this.
Imho changing the regex for the mac subnodes was simply forgotten to be updated on initial mt7988 support patch.
I try to rephrase it like this:
Binding was not aware for 3 MAC subnodes because previous mediatek SoC had only 2. Change this to allow 3 GMAC in mt7988 devicetree.
Quoted 6 lines
Quoted 3 lines
MT7988 has 4 FE IRQs (currently only 2 are used) and 4 IRQs for use
mt7988 or MT7988? gmac or GMAC? SRAM or SRAM? and so on... it is not easy to read and understand your commit msgs.
Ok,i always write those names in uppercase.
Quoted 39 lines
Quoted 39 lines
with RSS/LRO later.
Signed-off-by Frank Wunderlich <[email protected]>---
v6:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- add sram-property
- drop second reg entry and minitems as there is only 1 item left againv5:
- fix v4 logmessage and change description a bit describing how i get the irq count.
- update binding for 8 irqs with different names (rx,tx => fe0..fe3) including the 2 reserved irqs which can be used later
- change rx-ringX to pdmaX to be closer to hardware documentationv4:
- increase max interrupts to 6 because of adding RSS/LRO interrupts (4) and dropping 2 reserved irqs (0+3) around rx+tx
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988
this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/v2:
- change reg to list of items--- Documentation/devicetree/bindings/net/mediatek,net.yaml | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +0
-0@@ -28,7 +28,8 @@ properties: - ralink,rt5350-eth
Quoted 7 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml properties: · line 32
Quoted 4 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +2
-1reg: - maxItems: 1 + items: + - description: Register for accessing the MACs.Why making this change? It's redundant and nothing in commit msg explains that.
I was instructed (where we had 2 regs in previous Version) to name the regs...but as we have one reg again,i can drop this change. Thought a description is better than a count.
Quoted 3 lines
Best regards,
Krzysztof
regards Frank
Re: [PATCH v7 02/14] dt-bindings: net: mediatek,net: update for mt7988
Quoted 11 lines · Frank Wunderlich
Am 1. Juli 2025 08:41:42 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 10 lines · Frank Wunderlich
Quoted 4 lines
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
I asked why you are updating. You claim you update because it has 3 GMAC... but that's irrelevant, because it is easy to answer with: it did not have 3 GMAC before?
Quoted 6 lines
Quoted 2 lines
So same question: Provide real reason why you are making updates. That's why you have commit msg.
MT7988 had always 3 gmac,but no dts with ethernet node till now.
As i try to upstream the dts,i fell over this.
What does it mean? Are you adding new device or not? Nothing explains that something was missing.
Quoted 4 lines
Imho changing the regex for the mac subnodes was simply forgotten to be updated on initial mt7988 support patch.
Fix
your
wrapping because
it is
difficult
to follow
such
style.
Quoted 6 lines
I try to rephrase it like this:
Binding was not aware for 3 MAC subnodes because previous mediatek SoC had only 2. Change this to allow 3 GMAC in mt7988 devicetree.
So a fix for existing? Than add Fixes tag, describe the issue and fix ONLY that issue.
Best regards,
Krzysztof
Aw: Re: [PATCH v7 02/14] dt-bindings: net: mediatek,net: update for mt7988
Quoted 19 lines
Gesendet: Mittwoch, 2. Juli 2025 um 08:29
Von: "Krzysztof Kozlowski" <[email protected]>
Betreff: Re: [PATCH v7 02/14] dt-bindings: net: mediatek,net: update for mt7988Quoted 14 lines · Frank Wunderlich
Am 1. Juli 2025 08:41:42 MESZ schrieb Krzysztof Kozlowski <[email protected]>:
Quoted 12 lines · Frank Wunderlich
Quoted 4 lines
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
I asked why you are updating. You claim you update because it has 3 GMAC... but that's irrelevant, because it is easy to answer with: it did not have 3 GMAC before?
So same question: Provide real reason why you are making updates. That's why you have commit msg.
Quoted 6 lines
Quoted 3 lines
MT7988 had always 3 gmac,but no dts with ethernet node till now.
As i try to upstream the dts,i fell over this.What does it mean? Are you adding new device or not? Nothing explains that something was missing.
The binding already exists, but was incomplete. It was added while changing ethernet driver but was not used because i'm the first person adding mt7988 Ethernet node to devicetree in this series.
Quoted 5 lines
Quoted 4 lines
Imho changing the regex for the mac subnodes was simply forgotten to be updated on initial mt7988 support patch.
Quoted 8 lines
Fix
your
wrapping because
it is
difficult
to follow
such
style.
i understand that it is not the best, but i have to manually wrap lines because neither my webmail nor my Android Mail-App (K9Mail) supports automatic wrapping (created a feature-request some years ago which got rejected). I try to wrap it as good as possible, but still manually (on phone it is not that easy).
Quoted 9 lines
Quoted 6 lines
I try to rephrase it like this:
Binding was not aware for 3 MAC subnodes because previous mediatek SoC had only 2. Change this to allow 3 GMAC in mt7988 devicetree.
So a fix for existing? Than add Fixes tag, describe the issue and fix ONLY that issue.
Yes, binding for mt7988 already exists withing the mediatek,net binding, but the pattern for mac subnodes was not updated while adding. So i had to do it before adding the ethernet node to dts in same series.
But yes, i can separate this change again and add Fixes Tag. So just the sram-Property is added in this patch and i repharse it like this.
Quoted 2 lines
Best regards,
Krzysztof
regards Frank
PATCH v7 3/14 dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add own dsa-port binding for SoC with internal switch where only phy-mode 'internal' is valid.
--- .../bindings/net/dsa/mediatek,mt7530.yaml | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +13 -1
@@ -190,6 +190,18 @@ required: - reg $defs: + builtin-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-6]$": + if: + required: [ ethernet ] + then: + properties: + phy-mode: + const: internal + mt7530-dsa-port: patternProperties: "^(ethernet-)?ports$":
@@ -297,7 +309,7 @@ allOf: - airoha,en7581-switch - airoha,an7583-switch then: - $ref: "#/$defs/mt7530-dsa-port" + $ref: "#/$defs/builtin-dsa-port" properties: gpio-controller: false mediatek,mcm: false
Signature · 1 line
2.43.0
PATCH v7 4/14 dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Mt7988 buildin switch has own mdio bus where ge-phys are connected. Add related property for this.
---
v2:
- change from patternproperty to property
- add unevaluatedProperties and mediatek,pio subproperty
--- .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml | 10 ++++++++++ 1 file changed, 10 insertions(+)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +10 -0
@@ -136,6 +136,16 @@ properties: See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for details for the regulator setup on these boards. + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + mediatek,pio: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle pointing to the mediatek pinctrl node. + mediatek,mcm: type: boolean description:
Signature · 1 line
2.43.0
PATCH v7 5/14 dt-bindings: interconnect: add mt7988-cci compatible
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add compatible for Mediatek MT7988 SoC with mediatek,mt8183-cci fallback which is taken by driver.
---
v2:
- no RFC
- drop "items" as sugested by conor
--- .../bindings/interconnect/mediatek,cci.yaml | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml +8 -3
@@ -17,9 +17,14 @@ description: | properties: compatible: - enum: - - mediatek,mt8183-cci - - mediatek,mt8186-cci + oneOf: + - enum: + - mediatek,mt8183-cci + - mediatek,mt8186-cci + - items: + - enum: + - mediatek,mt7988-cci + - const: mediatek,mt8183-cci clocks: items:
Signature · 1 line
2.43.0
PATCH v7 6/14 arm64: dts: mediatek: mt7988: add cci node
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add cci devicetree node for cpu frequency scaling.
---
v3:
- add mt7988-cci compatible as suggested by angelo
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 33 +++++++++++++++++++++++ 1 file changed, 33 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +33 -0
@@ -12,6 +12,35 @@ / { #address-cells = <2>; #size-cells = <2>; + cci: cci { + compatible = "mediatek,mt7988-cci", "mediatek,mt8183-cci"; + clocks = <&mcusys CLK_MCU_BUS_DIV_SEL>, + <&topckgen CLK_TOP_XTAL>; + clock-names = "cci", "intermediate"; + operating-points-v2 = <&cci_opp>; + }; + + cci_opp: opp-table-cci { + compatible = "operating-points-v2"; + opp-shared; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <850000>; + }; + opp-660000000 { + opp-hz = /bits/ 64 <660000000>; + opp-microvolt = <850000>; + }; + opp-900000000 { + opp-hz = /bits/ 64 <900000000>; + opp-microvolt = <850000>; + }; + opp-1080000000 { + opp-hz = /bits/ 64 <1080000000>; + opp-microvolt = <900000>; + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>;
@@ -25,6 +54,7 @@ cpu0: cpu@0 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu1: cpu@1 {
@@ -36,6 +66,7 @@ cpu1: cpu@1 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu2: cpu@2 {
@@ -47,6 +78,7 @@ cpu2: cpu@2 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu3: cpu@3 {
@@ -58,6 +90,7 @@ cpu3: cpu@3 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cluster0_opp: opp-table-0 {
Signature · 1 line
2.43.0
PATCH v7 7/14 arm64: dts: mediatek: mt7988: add basic ethernet-nodes
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add basic ethernet related nodes.
Mac1+2 needs pcs (sgmii+usxgmii) to work correctly which will be linked later when driver is merged.
---
v6:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)
v5:
- add reserved irqs and change names to fe0..fe3
- change rx-ringX to pdmaX to be closer to documentation
v4:
- comment for fixed-link on gmac0
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
- add interrupts for RSS
- add interrupt-names and drop reserved irqs for ethernet
- some reordering
- eth-reg and clock whitespace-fix based on angelos review
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 137 +++++++++++++++++++++- 1 file changed, 134 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +134 -3
@@ -680,7 +680,28 @@ xphyu3port0: usb-phy@11e13000 { }; }; - clock-controller@11f40000 { + xfi_tphy0: phy@11f20000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f20000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_0_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 14>; + mediatek,usxgmii-performance-errata; + #phy-cells = <0>; + }; + + xfi_tphy1: phy@11f30000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f30000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_1_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 15>; + #phy-cells = <0>; + }; + + xfi_pll: clock-controller@11f40000 { compatible = "mediatek,mt7988-xfi-pll"; reg = <0 0x11f40000 0 0x1000>; resets = <&watchdog 16>;
@@ -714,19 +735,129 @@ phy_calibration_p3: calib@97c { }; }; - clock-controller@15000000 { + ethsys: clock-controller@15000000 { compatible = "mediatek,mt7988-ethsys", "syscon"; reg = <0 0x15000000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; - clock-controller@15031000 { + ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; + + eth: ethernet@15100000 { + compatible = "mediatek,mt7988-eth"; + reg = <0 0x15100000 0 0x80000>; + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "fe0", "fe1", "fe2", "fe3", "pdma0", + "pdma1", "pdma2", "pdma3"; + clocks = <ðsys CLK_ETHDMA_CRYPT0_EN>, + <ðsys CLK_ETHDMA_FE_EN>, + <ðsys CLK_ETHDMA_GP2_EN>, + <ðsys CLK_ETHDMA_GP1_EN>, + <ðsys CLK_ETHDMA_GP3_EN>, + <ðwarp CLK_ETHWARP_WOCPU2_EN>, + <ðwarp CLK_ETHWARP_WOCPU1_EN>, + <ðwarp CLK_ETHWARP_WOCPU0_EN>, + <ðsys CLK_ETHDMA_ESW_EN>, + <&topckgen CLK_TOP_ETH_GMII_SEL>, + <&topckgen CLK_TOP_ETH_REFCK_50M_SEL>, + <&topckgen CLK_TOP_ETH_SYS_200M_SEL>, + <&topckgen CLK_TOP_ETH_SYS_SEL>, + <&topckgen CLK_TOP_ETH_XGMII_SEL>, + <&topckgen CLK_TOP_ETH_MII_SEL>, + <&topckgen CLK_TOP_NETSYS_SEL>, + <&topckgen CLK_TOP_NETSYS_500M_SEL>, + <&topckgen CLK_TOP_NETSYS_PAO_2X_SEL>, + <&topckgen CLK_TOP_NETSYS_SYNC_250M_SEL>, + <&topckgen CLK_TOP_NETSYS_PPEFB_250M_SEL>, + <&topckgen CLK_TOP_NETSYS_WARP_SEL>, + <ðsys CLK_ETHDMA_XGP1_EN>, + <ðsys CLK_ETHDMA_XGP2_EN>, + <ðsys CLK_ETHDMA_XGP3_EN>; + clock-names = "crypto", "fe", "gp2", "gp1", "gp3", + "ethwarp_wocpu2", "ethwarp_wocpu1", + "ethwarp_wocpu0", "esw", "top_eth_gmii_sel", + "top_eth_refck_50m_sel", "top_eth_sys_200m_sel", + "top_eth_sys_sel", "top_eth_xgmii_sel", + "top_eth_mii_sel", "top_netsys_sel", + "top_netsys_500m_sel", "top_netsys_pao_2x_sel", + "top_netsys_sync_250m_sel", + "top_netsys_ppefb_250m_sel", + "top_netsys_warp_sel","xgp1", "xgp2", "xgp3"; + assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>, + <&topckgen CLK_TOP_NETSYS_GSW_SEL>, + <&topckgen CLK_TOP_USXGMII_SBUS_0_SEL>, + <&topckgen CLK_TOP_USXGMII_SBUS_1_SEL>, + <&topckgen CLK_TOP_SGM_0_SEL>, + <&topckgen CLK_TOP_SGM_1_SEL>; + assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>, + <&topckgen CLK_TOP_NET1PLL_D4>, + <&topckgen CLK_TOP_NET1PLL_D8_D4>, + <&topckgen CLK_TOP_NET1PLL_D8_D4>, + <&apmixedsys CLK_APMIXED_SGMPLL>, + <&apmixedsys CLK_APMIXED_SGMPLL>; + sram = <ð_sram>; + #address-cells = <1>; + #size-cells = <0>; + mediatek,ethsys = <ðsys>; + mediatek,infracfg = <&topmisc>; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "internal"; + + /* Connected to internal switch */ + fixed-link { + speed = <10000>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + status = "disabled"; + }; + + gmac2: mac@2 { + compatible = "mediatek,eth-mac"; + reg = <2>; + status = "disabled"; + }; + + mdio_bus: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* internal 2.5G PHY */ + int_2p5g_phy: ethernet-phy@15 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <15>; + }; + }; + }; + + eth_sram: sram@15400000 { + compatible = "mmio-sram"; + reg = <0 0x15400000 0 0x200000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x15400000 0 0x200000>; + }; }; thermal-zones {
Signature · 1 line
2.43.0
Re: [PATCH v7 07/14] arm64: dts: mediatek: mt7988: add basic ethernet-nodes
Quoted 79 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Add basic ethernet related nodes.
Mac1+2 needs pcs (sgmii+usxgmii) to work correctly which will be linked later when driver is merged.
Signed-off-by Daniel Golle <[email protected]>Signed-off-by Frank Wunderlich <[email protected]>---
v6:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needsCONFIG_SRAM)v5:
- add reserved irqs and change names to fe0..fe3
- change rx-ringX to pdmaX to be closer to documentationv4:
- comment for fixed-link on gmac0
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
- add interrupts for RSS
- add interrupt-names and drop reserved irqs for ethernet
- some reordering
- eth-reg and clock whitespace-fix based on angelos review--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 137 +++++++++++++++++++++- 1 file changed, 134 insertions(+), 3 deletions(-)arch/arm64/boot/dts/mediatek/mt7988a.dtsi +23
-3@@ -680,7 +680,28 @@ xphyu3port0: usb-phy@11e13000 { }; }; - clock-controller@11f40000 { + xfi_tphy0: phy@11f20000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f20000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_0_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 14>; + mediatek,usxgmii-performance-errata; + #phy-cells = <0>; + }; + + xfi_tphy1: phy@11f30000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f30000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_1_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 15>; + #phy-cells = <0>; + }; + + xfi_pll: clock-controller@11f40000 { compatible = "mediatek,mt7988-xfi-pll"; reg = <0 0x11f40000 0 0x1000>; resets = <&watchdog 16>;@@ -714,19 +735,129 @@ phy_calibration_p3: calib@97c { }; }; - clock-controller@15000000 { + ethsys: clock-controller@15000000 { compatible = "mediatek,mt7988-ethsys", "syscon"; reg = <0 0x15000000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; - clock-controller@15031000 {
arch/arm64/boot/dts/mediatek/mt7988a.dtsi phy_calibration_p3: calib@97c { · line 754
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +5
-0+ ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; + + eth: ethernet@15100000 { + compatible = "mediatek,mt7988-eth"; + reg = <0 0x15100000 0 0x80000>;
I think this should be
reg = <0 0x15100000 0 0x40000>;
as the range from 15140000 ~ 1517ffff is used as SRAM on MT7981/MT7986 and doesn't seem to be used at all on MT7988.
root@OpenWrt:~# devmem 0x15140000 32 0xDEADBEEF ... root@OpenWrt:~# devmem 0x1517fffc 32 0xDEADBEEF (with 0xDEADBEEF all that range)
PATCH v7 8/14 arm64: dts: mediatek: mt7988: add switch node
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add mt7988 builtin mt753x switch nodes.
---
v4:
- drop phy-mode for gsw-phy
- reorder phy-mode after phy-handle
- drop interrupt parent from switch
v2:
- drop labels and led-function too (have to be in board)
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 148 ++++++++++++++++++++++ 1 file changed, 148 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +148 -0
@@ -742,6 +742,154 @@ ethsys: clock-controller@15000000 { #reset-cells = <1>; }; + switch: switch@15020000 { + compatible = "mediatek,mt7988-switch"; + reg = <0 0x15020000 0 0x8000>; + interrupt-controller; + #interrupt-cells = <1>; + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + resets = <ðwarp MT7988_ETHWARP_RST_SWITCH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + gsw_port0: port@0 { + reg = <0>; + phy-handle = <&gsw_phy0>; + phy-mode = "internal"; + }; + + gsw_port1: port@1 { + reg = <1>; + phy-handle = <&gsw_phy1>; + phy-mode = "internal"; + }; + + gsw_port2: port@2 { + reg = <2>; + phy-handle = <&gsw_phy2>; + phy-mode = "internal"; + }; + + gsw_port3: port@3 { + reg = <3>; + phy-handle = <&gsw_phy3>; + phy-mode = "internal"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "internal"; + + fixed-link { + speed = <10000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + mediatek,pio = <&pio>; + + gsw_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupts = <0>; + nvmem-cells = <&phy_calibration_p0>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy0_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy0_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + interrupts = <1>; + nvmem-cells = <&phy_calibration_p1>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy1_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy1_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + interrupts = <2>; + nvmem-cells = <&phy_calibration_p2>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy2_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy2_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + interrupts = <3>; + nvmem-cells = <&phy_calibration_p3>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy3_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy3_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + }; + }; + ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>;
Signature · 1 line
2.43.0
PATCH v7 9/14 arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
CCI requires proc-supply. Add it on board level.
--- arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +4 -0
@@ -40,6 +40,10 @@ reg_3p3v: regulator-3p3v { }; }; +&cci { + proc-supply = <&rt5190_buck3>; +}; + &cpu0 { proc-supply = <&rt5190_buck3>; };
Signature · 1 line
2.43.0
PATCH v7 10/14 arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Pins were moved from SoC dtsi to Board level dtsi without cleaning up to needed ones. Drop the unused pins now.
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 89 ------------------- 1 file changed, 89 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +0 -89
@@ -223,18 +223,6 @@ &pcie3 { }; &pio { - mdio0_pins: mdio0-pins { - mux { - function = "eth"; - groups = "mdc_mdio0"; - }; - - conf { - pins = "SMI_0_MDC", "SMI_0_MDIO"; - drive-strength = <8>; - }; - }; - i2c0_pins: i2c0-g0-pins { mux { function = "i2c";
@@ -249,20 +237,6 @@ mux { }; }; - i2c1_sfp_pins: i2c1-sfp-g0-pins { - mux { - function = "i2c"; - groups = "i2c1_sfp"; - }; - }; - - i2c2_0_pins: i2c2-g0-pins { - mux { - function = "i2c"; - groups = "i2c2_0"; - }; - }; - i2c2_1_pins: i2c2-g1-pins { mux { function = "i2c";
@@ -298,34 +272,6 @@ mux { }; }; - gbe0_led1_pins: gbe0-led1-pins { - mux { - function = "led"; - groups = "gbe0_led1"; - }; - }; - - gbe1_led1_pins: gbe1-led1-pins { - mux { - function = "led"; - groups = "gbe1_led1"; - }; - }; - - gbe2_led1_pins: gbe2-led1-pins { - mux { - function = "led"; - groups = "gbe2_led1"; - }; - }; - - gbe3_led1_pins: gbe3-led1-pins { - mux { - function = "led"; - groups = "gbe3_led1"; - }; - }; - i2p5gbe_led0_pins: 2p5gbe-led0-pins { mux { function = "led";
@@ -333,13 +279,6 @@ mux { }; }; - i2p5gbe_led1_pins: 2p5gbe-led1-pins { - mux { - function = "led"; - groups = "2p5gbe_led1"; - }; - }; - mmc0_pins_emmc_45: mmc0-emmc-45-pins { mux { function = "flash";
@@ -361,40 +300,12 @@ mux { }; }; - snfi_pins: snfi-pins { - mux { - function = "flash"; - groups = "snfi"; - }; - }; - - spi0_pins: spi0-pins { - mux { - function = "spi"; - groups = "spi0"; - }; - }; - spi0_flash_pins: spi0-flash-pins { mux { function = "spi"; groups = "spi0", "spi0_wp_hold"; }; }; - - spi2_pins: spi2-pins { - mux { - function = "spi"; - groups = "spi2"; - }; - }; - - spi2_flash_pins: spi2-flash-pins { - mux { - function = "spi"; - groups = "spi2", "spi2_wp_hold"; - }; - }; }; &pwm {
Signature · 1 line
2.43.0
PATCH v7 11/14 arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Bananapi R4 has a green and a blue led which can be switched by gpio. Green led is for running state so default on.
Green led also shares pin with eeprom writeprotect where led off allows writing to eeprom.
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
@@ -21,6 +21,25 @@ fan: pwm-fan { status = "okay"; }; + gpio-leds { + compatible = "gpio-leds"; + + led_green: led-green { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 79 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_blue: led-blue { + function = LED_FUNCTION_WPS; + color = <LED_COLOR_ID_BLUE>; + gpios = <&pio 63 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_1p8v: regulator-1p8v { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V";
Signature · 1 line
2.43.0
PATCH v7 12/14 arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add aliases for gmacs to allow bootloader setting mac-adresses.
--- arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +6 -0
@@ -8,6 +8,12 @@ #include "mt7988a.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + ethernet2 = &gmac2; + }; + chosen { stdout-path = "serial0:115200n8"; };
Signature · 1 line
2.43.0
PATCH v7 13/14 arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add SFP cages to Bananapi-R4 board. The 2.5g phy variant only contains the wan-SFP, so add this to common dtsi and the lan-sfp only to the dual-SFP variant.
---
v4:
- update 2g5-board (reorder and drop phy-connection-type)
- order sfp properties
v3:
- enable mac with 2.5g phy on r4 phy variant because driver is now mainline
--- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 +++++++++++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 +++++++++++++++++++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++ 3 files changed, 49 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-2g5.dts +11 -0
@@ -9,3 +9,14 @@ / { model = "Banana Pi BPI-R4 (1x SFP+, 1x 2.5GbE)"; chassis-type = "embedded"; }; + +&gmac1 { + phy = <&int_2p5g_phy>; + phy-mode = "internal"; + status = "okay"; +}; + +&int_2p5g_phy { + pinctrl-0 = <&i2p5gbe_led0_pins>; + pinctrl-names = "i2p5gbe-led"; +};
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts +19 -0
@@ -8,6 +8,25 @@ / { compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; model = "Banana Pi BPI-R4 (2x SFP+)"; chassis-type = "embedded"; + + /* SFP2 cage (LAN) */ + sfp2: sfp2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + maximum-power-milliwatt = <3000>; + + los-gpios = <&pio 2 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 83 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&pio 3 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 1 GPIO_ACTIVE_HIGH>; + }; +}; + +&gmac1 { + managed = "in-band-status"; + phy-mode = "usxgmii"; + sfp = <&sfp2>; }; &pca9545 {
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
@@ -63,6 +63,19 @@ reg_3p3v: regulator-3p3v { regulator-boot-on; regulator-always-on; }; + + /* SFP1 cage (WAN) */ + sfp1: sfp1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + maximum-power-milliwatt = <3000>; + + los-gpios = <&pio 54 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&pio 21 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 70 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 69 GPIO_ACTIVE_HIGH>; + }; }; &cci {
@@ -133,6 +146,12 @@ map-cpu-active-low { }; }; +&gmac2 { + managed = "in-band-status"; + phy-mode = "usxgmii"; + sfp = <&sfp1>; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
PATCH v7 14/14 arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Assign pinctrl to switch phys and leds.
---
v4:
- reorder switch phy(-led) properties
v2:
- add labels and led-function and include after dropping from soc dtsi
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 61 +++++++++++++++++++ 1 file changed, 61 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +61 -0
@@ -4,6 +4,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/richtek,rt5190a-regulator.h> +#include <dt-bindings/leds/common.h> #include "mt7988a.dtsi"
@@ -152,6 +153,66 @@ &gmac2 { sfp = <&sfp1>; }; +&gsw_phy0 { + pinctrl-0 = <&gbe0_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy0_led0 { + function = LED_FUNCTION_WAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port0 { + label = "wan"; +}; + +&gsw_phy1 { + pinctrl-0 = <&gbe1_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy1_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port1 { + label = "lan1"; +}; + +&gsw_phy2 { + pinctrl-0 = <&gbe2_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy2_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port2 { + label = "lan2"; +}; + +&gsw_phy3 { + pinctrl-0 = <&gbe3_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy3_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port3 { + label = "lan3"; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
Quoted 2 lines
Frank Wunderlich (14):
...
Quoted 5 lines
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for
mt7988
dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
dt-bindings: interconnect: add mt7988-cci compatible
arm64: dts: mediatek: mt7988: add cci node
...
Quoted 3 lines
arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
...
Hi Angelo,
Maybe you can take the already reviewed patches (except exthernet + switch) so i do not need to resend them again and again and spam people too much because of the ethernet binding changes?
regards Frank