dt-bindings: thermal: Convert qoriq to json-schema
Subsystems (2)
PATCH v2 1/1 dt-bindings: thermal: Convert qoriq to json-schema
Convert the qoriq thermal binding to DT schema format using json-schema
---
Changes since V1:
- add 'maxItems' for 'fsl,tmu-range' property;
- add 'minItems'/'maxItems' and items descriptions for 'fsl,tmu-calibration' property;
- remove description for common property '#thermal-sensor-cells';
- refine 'fsl,tmu-calibration' format in example.
--- .../devicetree/bindings/thermal/qoriq-thermal.txt | 71 ------------- .../devicetree/bindings/thermal/qoriq-thermal.yaml | 112 +++++++++++++++++++++ 2 files changed, 112 insertions(+), 71 deletions(-) delete mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.txt create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml
Documentation/devicetree/bindings/thermal/qoriq-thermal.txt deleted +0 -71
@@ -1,71 +0,0 @@ -* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs - -Required properties: -- compatible : Must include "fsl,qoriq-tmu" or "fsl,imx8mq-tmu". The - version of the device is determined by the TMU IP Block Revision - Register (IPBRR0) at offset 0x0BF8. - Table of correspondences between IPBRR0 values and example chips: - Value Device - ---------- ----- - 0x01900102 T1040 -- reg : Address range of TMU registers. -- interrupts : Contains the interrupt for TMU. -- fsl,tmu-range : The values to be programmed into TTRnCR, as specified by - the SoC reference manual. The first cell is TTR0CR, the second is - TTR1CR, etc. -- fsl,tmu-calibration : A list of cell pairs containing temperature - calibration data, as specified by the SoC reference manual. - The first cell of each pair is the value to be written to TTCFGR, - and the second is the value to be written to TSCFGR. -- #thermal-sensor-cells : Must be 1. The sensor specifier is the monitoring - site ID, and represents the "n" in TRITSRn and TRATSRn. - -Optional property: -- little-endian : If present, the TMU registers are little endian. If absent, - the default is big endian. -- clocks : the clock for clocking the TMU silicon. - -Example: - -tmu@f0000 { - compatible = "fsl,qoriq-tmu"; - reg = <0xf0000 0x1000>; - interrupts = <18 2 0 0>; - fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>; - fsl,tmu-calibration = <0x00000000 0x00000025 - 0x00000001 0x00000028 - 0x00000002 0x0000002d - 0x00000003 0x00000031 - 0x00000004 0x00000036 - 0x00000005 0x0000003a - 0x00000006 0x00000040 - 0x00000007 0x00000044 - 0x00000008 0x0000004a - 0x00000009 0x0000004f - 0x0000000a 0x00000054 - - 0x00010000 0x0000000d - 0x00010001 0x00000013 - 0x00010002 0x00000019 - 0x00010003 0x0000001f - 0x00010004 0x00000025 - 0x00010005 0x0000002d - 0x00010006 0x00000033 - 0x00010007 0x00000043 - 0x00010008 0x0000004b - 0x00010009 0x00000053 - - 0x00020000 0x00000010 - 0x00020001 0x00000017 - 0x00020002 0x0000001f - 0x00020003 0x00000029 - 0x00020004 0x00000031 - 0x00020005 0x0000003c - 0x00020006 0x00000042 - 0x00020007 0x0000004d - 0x00020008 0x00000056 - - 0x00030000 0x00000012 - 0x00030001 0x0000001d>; - #thermal-sensor-cells = <1>; -};
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml new file +112 -0
112 lines not on this page · raw message
Signature · 1 line
2.7.4
Quoted 9 lines · Anson Huang
Convert the qoriq thermal binding to DT schema format using json-schema
Signed-off-by Anson Huang <[email protected]>---
Changes since V1:
- add 'maxItems' for 'fsl,tmu-range' property;
- add 'minItems'/'maxItems' and items descriptions for 'fsl,tmu-calibration' property;
- remove description for common property '#thermal-sensor-cells';
- refine 'fsl,tmu-calibration' format in example.
Quoted 7 lines
--- .../devicetree/bindings/thermal/qoriq-thermal.txt | 71 ------------- .../devicetree/bindings/thermal/qoriq-thermal.yaml | 112 +++++++++++++++++++++ 2 files changed, 112 insertions(+), 71 deletions(-) delete mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.txt create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml
Applied, thanks!
Quoted 16 lines · Anson Huang
Convert the qoriq thermal binding to DT schema format using json-schema
Signed-off-by Anson Huang <[email protected]>---
Changes since V1:
- add 'maxItems' for 'fsl,tmu-range' property;
- add 'minItems'/'maxItems' and items descriptions for 'fsl,tmu-calibration' property;
- remove description for common property '#thermal-sensor-cells';
- refine 'fsl,tmu-calibration' format in example.--- .../devicetree/bindings/thermal/qoriq-thermal.txt | 71 ------------- .../devicetree/bindings/thermal/qoriq-thermal.yaml | 112 +++++++++++++++++++++ 2 files changed, 112 insertions(+), 71 deletions(-) delete mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.txt create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml
[...]
Quoted 6 lines
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml new file +0
-0
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml line 10
Quoted 10 lines
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml new file +10
-0@@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/qoriq-thermal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs + +maintainers: + - Hongtao Jia <[email protected]>
This email is bouncing. Should be @nxp.com?
Rob
Hi, Rob
Quoted 60 lines
Subject: Re: [PATCH V2] dt-bindings: thermal: Convert qoriq to json-schema
Quoted 9 lines · Anson Huang
Convert the qoriq thermal binding to DT schema format using json-schema
Signed-off-by Anson Huang <[email protected]>---
Changes since V1:
- add 'maxItems' for 'fsl,tmu-range' property;
- add 'minItems'/'maxItems' and items descriptions for'fsl,tmu-calibration' property;
Quoted 10 lines
- remove description for common property '#thermal-sensor-cells';
- refine 'fsl,tmu-calibration' format in example.--- .../devicetree/bindings/thermal/qoriq-thermal.txt | 71 ------------- .../devicetree/bindings/thermal/qoriq-thermal.yaml | 112 +++++++++++++++++++++ 2 files changed, 112 insertions(+), 71 deletions(-) delete mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.txt create mode 100644
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml[...]
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml line 4
Quoted 13 lines
diff --git
a/Documentation/devicetree/bindings/thermal/qoriq-thermal.yamlb/Documentation/devicetree/bindings/thermal/qoriq-thermal.yamlnew file mode 100644
index 0000000..c5df999Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml new file +4
-0@@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 +--- +$id: +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi+cetree.org%2Fschemas%2Fthermal%2Fqoriq-thermal.yaml%23&data=0 2%7C
Quoted 1 line
+01%7CAnson.Huang%40nxp.com%7Cbb14200bf9dd47404fd308d8064c5719 %7C686ea
Quoted 1 line
+1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637266272232329711&am p;sdata=gz
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml
Quoted 4 lines
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml new file +3
-0+zLUrr9f56HcPB1iy4xQvj2tw41Mc9Af5QUJbuvnCY%3D&reserved=0 +$schema: +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi+cetree.org%2Fmeta-schemas%2Fcore.yaml%23&data=02%7C01%7CAns on.Hua
Quoted 1 line
+ng%40nxp.com%7Cbb14200bf9dd47404fd308d8064c5719%7C686ea1d3bc2
b4c6fa92Quoted 1 line
+cd99c5c301635%7C0%7C0%7C637266272232329711&sdata=7qkHkpj XPXMYn13c
Quoted 8 lines
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml line 10
Quoted 6 lines
Documentation/devicetree/bindings/thermal/qoriq-thermal.yaml new file +6
-0+I1pndBwFgfI2%2F6gMfCgWPrQSnmc%3D&reserved=0 + +title: Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs + +maintainers: + - Hongtao Jia <[email protected]>This email is bouncing. Should be @nxp.com?
Yes, but looks like hongtao is no longer in NXP, so the [email protected] can NOT be touched in, I sent out V3 patch and also got the notification of failed to send to [email protected], so I will use myself as maintainer, correct me if anything wrong. Will send a V4.
Thanks,
Anson