Skip to contentSkip to conversation

hw/riscv: Add Microchip PolarFire SoC Icicle Kit board support

PATCH Superseded Bin Meng 2 participants 20 messages Aug 29, 2020 – Aug 30, 2020

Subsystems (4)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Bin Meng

author
#0 lore raw

v2 cover hw/riscv: Add Microchip PolarFire SoC Icicle Kit board support

From: Bin Meng <[email protected]>

This adds support for Microchip PolarFire SoC Icicle Kit board. The Icicle Kit board integrates a PolarFire SoC, with one SiFive's E51 plus four U54 cores and many on-chip peripherals and an FPGA.

For more details about Microchip PolarFire SoC, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga

The Icicle Kit board information can be found here:
https://www.microsemi.com/existing-parts/parts/152514

Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000. The RISC-V CPU and HART codes has been updated to set the core's reset vector based on a configurable property from machine codes.

The following perepherals are created as an unimplemented device:

- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
- GPIO

The following perepherals are emulated:
- SiFive CLINT
- SiFive PLIC
- PolarFire SoC Multi-Mode UART
- SiFive PDMA
- Cadence eMMC/SDHCI controller
- Cadence Gigabit Ethernet MAC

The BIOS image used by this machine is hss.bin, aka Hart Software Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services

To launch this machine:

$ qemu-system-riscv64 -M microchip-icicle-kit -smp 5 \
    -bios path/to/hss.bin -sd path/to/sdcard.img \
    -nic tap,ifname=tap,script=no,model=cadence_gem \
    -display none -serial stdio \
    -chardev socket,id=serial1,path=serial1.sock,server,wait \
    -serial chardev:serial1

The memory is set to 1 GiB by default to match the hardware. A sanity check on ram size is performed in the machine init routine to prompt user to increase the RAM size to > 1 GiB when less than 1 GiB ram is detected.

HSS output is on the first serial port (stdio) and U-Boot/Linux outputs on the 2nd serial port. OpenSBI outputs on a random serial port due to the lottery mechanism used during the multi-core boot.

Please check the QEMU WiKi page for the target specific information:
https://wiki.qemu.org/Documentation/Platforms/RISCV#Microchip_PolarFire_SoC_Icicle_Kit

Changes in v2:
- change to update hw/char/meson.build
- add impl.min_access_size and impl.max_access_size as part of MemoryRegionOps and remove the allignment check
- change to update hw/sd/meson.build
- change the name to "generic-sdhci" when calling object_initialize_child()
- add a container MR to simplify out-of-bounds access checks
- do not initialize TYPE_SYSBUS_SDHCI in the SoC instance_init(), instead move that to the cadence_sdhci model
- do not access generic-sdhci's state directly,
instead move that to the cadence_sdhci model
- change to update hw/dma/meson.build
- rename the file names to sifive_pdma.[c|h]
- update irq number to 8 per the SiFive FU540 manual
- fix the register offset for channel 1/2/3 in the read/write ops
- connect 8 IRQs to the PLIC
- change "phy-addr" default value to BOARD_PHY_ADDRESS

Bin Meng (16):
target/riscv: cpu: Add a new 'resetvec' property
hw/riscv: hart: Add a new 'resetvec' property target/riscv: cpu: Set reset vector based on the configured property
value
hw/riscv: Initial support for Microchip PolarFire SoC Icicle Kit board hw/char: Add Microchip PolarFire SoC MMUART emulation hw/riscv: microchip_pfsoc: Connect 5 MMUARTs
hw/sd: Add Cadence SDHCI emulation
hw/riscv: microchip_pfsoc: Connect a Cadence SDHCI controller and an
SD card
hw/dma: Add SiFive platform DMA controller emulation hw/riscv: microchip_pfsoc: Connect a DMA controller hw/net: cadence_gem: Add a new 'phy-addr' property
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23 hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: clint: Avoid using hard-coded timebase frequency hw/riscv: sifive_u: Connect a DMA controller

 default-configs/riscv64-softmmu.mak |   1 +
 include/hw/char/mchp_pfsoc_mmuart.h |  61 +++++
 include/hw/dma/sifive_pdma.h        |  57 +++++
 include/hw/net/cadence_gem.h        |   2 +
 include/hw/riscv/microchip_pfsoc.h  | 133 +++++++++++
 include/hw/riscv/riscv_hart.h       |   1 +
 include/hw/riscv/sifive_clint.h     |   4 +-
 include/hw/riscv/sifive_u.h         |  11 +
 include/hw/sd/cadence_sdhci.h       |  47 ++++
 target/riscv/cpu.h                  |   7 +-
 hw/arm/xilinx_zynq.c                |   1 +
 hw/arm/xlnx-versal.c                |   1 +
 hw/arm/xlnx-zynqmp.c                |   1 +
 hw/char/mchp_pfsoc_mmuart.c         |  86 +++++++
 hw/dma/sifive_pdma.c                | 313 ++++++++++++++++++++++++++
 hw/net/cadence_gem.c                |   7 +-
 hw/riscv/microchip_pfsoc.c          | 437 ++++++++++++++++++++++++++++++++++++
 hw/riscv/opentitan.c                |   1 +
 hw/riscv/riscv_hart.c               |   3 +
 hw/riscv/sifive_clint.c             |  26 ++-
 hw/riscv/sifive_e.c                 |   4 +-
 hw/riscv/sifive_u.c                 |  35 ++-
 hw/riscv/spike.c                    |   3 +-
 hw/riscv/virt.c                     |   3 +-
 hw/sd/cadence_sdhci.c               | 193 ++++++++++++++++
 target/riscv/cpu.c                  |   8 +-
 target/riscv/cpu_helper.c           |   4 +-
 target/riscv/csr.c                  |   4 +-
 MAINTAINERS                         |   9 +
 hw/char/Kconfig                     |   3 +
 hw/char/meson.build                 |   1 +
 hw/dma/Kconfig                      |   3 +
 hw/dma/meson.build                  |   1 +
 hw/riscv/Kconfig                    |  10 +
 hw/riscv/meson.build                |   1 +
 hw/sd/Kconfig                       |   4 +
 hw/sd/meson.build                   |   1 +
 37 files changed, 1458 insertions(+), 29 deletions(-)
 create mode 100644 include/hw/char/mchp_pfsoc_mmuart.h
 create mode 100644 include/hw/dma/sifive_pdma.h
 create mode 100644 include/hw/riscv/microchip_pfsoc.h
 create mode 100644 include/hw/sd/cadence_sdhci.h
 create mode 100644 hw/char/mchp_pfsoc_mmuart.c
 create mode 100644 hw/dma/sifive_pdma.c
 create mode 100644 hw/riscv/microchip_pfsoc.c
 create mode 100644 hw/sd/cadence_sdhci.c
Signature · 1 line
2.7.4
author
#1 lore raw

PATCH v2 1/16 target/riscv: cpu: Add a new 'resetvec' property

From: Bin Meng <[email protected]>

Currently the reset vector address is hard-coded in a RISC-V CPU's instance_init() routine. In a real world we can have 2 exact same CPUs except for the reset vector address, which is pretty common in the RISC-V core IP licensing business.

Normally reset vector address is a configurable parameter. Let's create a 64-bit property to store the reset vector address which covers both 32-bit and 64-bit CPUs.

---

(no changes since v1)

 target/riscv/cpu.h | 1 +
 target/riscv/cpu.c | 1 +
 2 files changed, 2 insertions(+)
target/riscv/cpu.h +1 -0
index 383808b..dc350f0 100644
@@ -291,6 +291,7 @@ typedef struct RISCVCPU {
         uint16_t elen;
         bool mmu;
         bool pmp;
+        uint64_t resetvec;
     } cfg;
 } RISCVCPU;
 
target/riscv/cpu.c +1 -0
index 228b9bd..8067a26 100644
@@ -518,6 +518,7 @@ static Property riscv_cpu_properties[] = {
     DEFINE_PROP_UINT16("elen", RISCVCPU, cfg.elen, 64),
     DEFINE_PROP_BOOL("mmu", RISCVCPU, cfg.mmu, true),
     DEFINE_PROP_BOOL("pmp", RISCVCPU, cfg.pmp, true),
+    DEFINE_PROP_UINT64("resetvec", RISCVCPU, cfg.resetvec, DEFAULT_RSTVEC),
     DEFINE_PROP_END_OF_LIST(),
 };
 
Signature · 1 line
2.7.4
author
#2 lore raw

PATCH v2 2/16 hw/riscv: hart: Add a new 'resetvec' property

In reply to Bin Meng

From: Bin Meng <[email protected]>

RISC-V machines do not instantiate RISC-V CPUs directly, instead they do that via the hart array. Add a new property for the reset vector address to allow the value to be passed to the CPU, before CPU is realized.

---

(no changes since v1)

 include/hw/riscv/riscv_hart.h | 1 +
 hw/riscv/riscv_hart.c         | 3 +++
 2 files changed, 4 insertions(+)
include/hw/riscv/riscv_hart.h +1 -0
index c75856f..77aa4bc 100644
@@ -37,6 +37,7 @@ typedef struct RISCVHartArrayState {
     uint32_t num_harts;
     uint32_t hartid_base;
     char *cpu_type;
+    uint64_t resetvec;
     RISCVCPU *harts;
 } RISCVHartArrayState;
 
hw/riscv/riscv_hart.c +3 -0
index f59fe52..613ea2a 100644
@@ -31,6 +31,8 @@ static Property riscv_harts_props[] = {
     DEFINE_PROP_UINT32("num-harts", RISCVHartArrayState, num_harts, 1),
     DEFINE_PROP_UINT32("hartid-base", RISCVHartArrayState, hartid_base, 0),
     DEFINE_PROP_STRING("cpu-type", RISCVHartArrayState, cpu_type),
+    DEFINE_PROP_UINT64("resetvec", RISCVHartArrayState, resetvec,
+                       DEFAULT_RSTVEC),
     DEFINE_PROP_END_OF_LIST(),
 };
 
@@ -44,6 +46,7 @@ static bool riscv_hart_realize(RISCVHartArrayState *s, int idx,
                                char *cpu_type, Error **errp)
 {
     object_initialize_child(OBJECT(s), "harts[*]", &s->harts[idx], cpu_type);
+    qdev_prop_set_uint64(DEVICE(&s->harts[idx]), "resetvec", s->resetvec);
     s->harts[idx].env.mhartid = s->hartid_base + idx;
     qemu_register_reset(riscv_harts_cpu_reset, &s->harts[idx]);
     return qdev_realize(DEVICE(&s->harts[idx]), NULL, errp);
Signature · 1 line
2.7.4
author
#3 lore raw

PATCH v2 3/16 target/riscv: cpu: Set reset vector based on the configured property value

In reply to Bin Meng

From: Bin Meng <[email protected]>

Now that we have the newly introduced 'resetvec' property in the RISC-V CPU and HART, instead of hard-coding the reset vector addr in the CPU's instance_init(), move that to riscv_cpu_realize() based on the configured property value from the RISC-V machines.

---

(no changes since v1)

 hw/riscv/opentitan.c | 1 +
 hw/riscv/sifive_e.c  | 1 +
 hw/riscv/sifive_u.c  | 2 ++
 target/riscv/cpu.c   | 7 ++-----
 4 files changed, 6 insertions(+), 5 deletions(-)
hw/riscv/opentitan.c +1 -0
index 23ba3b4..0531bd8 100644
@@ -111,6 +111,7 @@ static void lowrisc_ibex_soc_realize(DeviceState *dev_soc, Error **errp)
                             &error_abort);
     object_property_set_int(OBJECT(&s->cpus), "num-harts", ms->smp.cpus,
                             &error_abort);
+    object_property_set_int(OBJECT(&s->cpus), "resetvec", 0x8090, &error_abort);
     sysbus_realize(SYS_BUS_DEVICE(&s->cpus), &error_abort);
 
     /* Boot ROM */
hw/riscv/sifive_e.c +1 -0
index ca55cc4..cd7560d 100644
@@ -177,6 +177,7 @@ static void sifive_e_soc_init(Object *obj)
     object_initialize_child(obj, "cpus", &s->cpus, TYPE_RISCV_HART_ARRAY);
     object_property_set_int(OBJECT(&s->cpus), "num-harts", ms->smp.cpus,
                             &error_abort);
+    object_property_set_int(OBJECT(&s->cpus), "resetvec", 0x1004, &error_abort);
     object_initialize_child(obj, "riscv.sifive.e.gpio0", &s->gpio,
                             TYPE_SIFIVE_GPIO);
 }
hw/riscv/sifive_u.c +2 -0
index a48046c..404d5e6 100644
@@ -611,6 +611,7 @@ static void sifive_u_soc_instance_init(Object *obj)
     qdev_prop_set_uint32(DEVICE(&s->e_cpus), "num-harts", 1);
     qdev_prop_set_uint32(DEVICE(&s->e_cpus), "hartid-base", 0);
     qdev_prop_set_string(DEVICE(&s->e_cpus), "cpu-type", SIFIVE_E_CPU);
+    qdev_prop_set_uint64(DEVICE(&s->e_cpus), "resetvec", 0x1004);
 
     object_initialize_child(obj, "u-cluster", &s->u_cluster, TYPE_CPU_CLUSTER);
     qdev_prop_set_uint32(DEVICE(&s->u_cluster), "cluster-id", 1);
@@ -620,6 +621,7 @@ static void sifive_u_soc_instance_init(Object *obj)
     qdev_prop_set_uint32(DEVICE(&s->u_cpus), "num-harts", ms->smp.cpus - 1);
     qdev_prop_set_uint32(DEVICE(&s->u_cpus), "hartid-base", 1);
     qdev_prop_set_string(DEVICE(&s->u_cpus), "cpu-type", SIFIVE_U_CPU);
+    qdev_prop_set_uint64(DEVICE(&s->u_cpus), "resetvec", 0x1004);
 
     object_initialize_child(obj, "prci", &s->prci, TYPE_SIFIVE_U_PRCI);
     object_initialize_child(obj, "otp", &s->otp, TYPE_SIFIVE_U_OTP);
target/riscv/cpu.c +2 -5
index 8067a26..bd41286 100644
@@ -128,7 +128,6 @@ static void riscv_any_cpu_init(Object *obj)
     CPURISCVState *env = &RISCV_CPU(obj)->env;
     set_misa(env, RVXLEN | RVI | RVM | RVA | RVF | RVD | RVC | RVU);
     set_priv_version(env, PRIV_VERSION_1_11_0);
-    set_resetvec(env, DEFAULT_RSTVEC);
 }
 
 static void riscv_base_cpu_init(Object *obj)
@@ -136,7 +135,6 @@ static void riscv_base_cpu_init(Object *obj)
     CPURISCVState *env = &RISCV_CPU(obj)->env;
     /* We set this in the realise function */
     set_misa(env, 0);
-    set_resetvec(env, DEFAULT_RSTVEC);
 }
 
 static void rvxx_sifive_u_cpu_init(Object *obj)
@@ -144,7 +142,6 @@ static void rvxx_sifive_u_cpu_init(Object *obj)
     CPURISCVState *env = &RISCV_CPU(obj)->env;
     set_misa(env, RVXLEN | RVI | RVM | RVA | RVF | RVD | RVC | RVS | RVU);
     set_priv_version(env, PRIV_VERSION_1_10_0);
-    set_resetvec(env, 0x1004);
 }
 
 static void rvxx_sifive_e_cpu_init(Object *obj)
@@ -152,7 +149,6 @@ static void rvxx_sifive_e_cpu_init(Object *obj)
     CPURISCVState *env = &RISCV_CPU(obj)->env;
     set_misa(env, RVXLEN | RVI | RVM | RVA | RVC | RVU);
     set_priv_version(env, PRIV_VERSION_1_10_0);
-    set_resetvec(env, 0x1004);
     qdev_prop_set_bit(DEVICE(obj), "mmu", false);
 }
 
@@ -163,7 +159,6 @@ static void rv32_ibex_cpu_init(Object *obj)
     CPURISCVState *env = &RISCV_CPU(obj)->env;
     set_misa(env, RV32 | RVI | RVM | RVC | RVU);
     set_priv_version(env, PRIV_VERSION_1_10_0);
-    set_resetvec(env, 0x8090);
     qdev_prop_set_bit(DEVICE(obj), "mmu", false);
 }
 
@@ -373,6 +368,8 @@ static void riscv_cpu_realize(DeviceState *dev, Error **errp)
         set_feature(env, RISCV_FEATURE_PMP);
     }
 
+    set_resetvec(env, cpu->cfg.resetvec);
+
     /* If misa isn't set (rv32 and rv64 machines) set it here */
     if (!env->misa) {
         /* Do some ISA extension error checking */
Signature · 1 line
2.7.4
author
#4 lore raw

PATCH v2 4/16 hw/riscv: Initial support for Microchip PolarFire SoC Icicle Kit board

In reply to Bin Meng

From: Bin Meng <[email protected]>

This is an initial support for Microchip PolarFire SoC Icicle Kit. The Icicle Kit board integrates a PolarFire SoC, with one SiFive's E51 plus four U54 cores and many on-chip peripherals and an FPGA.

For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga

Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000. The following perepherals are created as an unimplemented device:

- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG

More devices will be added later.

The BIOS image used by this machine is hss.bin, aka Hart Software Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services

To launch this machine:

$ qemu-system-riscv64 -nographic -M microchip-icicle-kit

The memory is set to 1 GiB by default to match the hardware. A sanity check on ram size is performed in the machine init routine to prompt user to increase the RAM size to > 1 GiB when less than 1 GiB ram is detected.

---

(no changes since v1)

 default-configs/riscv64-softmmu.mak |   1 +
 include/hw/riscv/microchip_pfsoc.h  |  88 ++++++++++
 hw/riscv/microchip_pfsoc.c          | 312 ++++++++++++++++++++++++++++++++++++
 MAINTAINERS                         |   7 +
 hw/riscv/Kconfig                    |   6 +
 hw/riscv/meson.build                |   1 +
 6 files changed, 415 insertions(+)
 create mode 100644 include/hw/riscv/microchip_pfsoc.h
 create mode 100644 hw/riscv/microchip_pfsoc.c
default-configs/riscv64-softmmu.mak +1 -0
index aaf6d73..76b6195 100644
@@ -10,3 +10,4 @@ CONFIG_SPIKE=y
 CONFIG_SIFIVE_E=y
 CONFIG_SIFIVE_U=y
 CONFIG_RISCV_VIRT=y
+CONFIG_MICROCHIP_PFSOC=y
include/hw/riscv/microchip_pfsoc.h new file +88 -0

88 lines not on this page · raw message

hw/riscv/microchip_pfsoc.c new file +312 -0

312 lines not on this page · raw message

MAINTAINERS +7 -0
index 5a22c8b..5359b39 100644
@@ -1315,6 +1315,13 @@ F: include/hw/riscv/opentitan.h
 F: include/hw/char/ibex_uart.h
 F: include/hw/intc/ibex_plic.h
 
+Microchip PolarFire SoC Icicle Kit
+M: Bin Meng <[email protected]>
+L: [email protected]
+S: Supported
+F: hw/riscv/microchip_pfsoc.c
+F: include/hw/riscv/microchip_pfsoc.h
+
 RX Machines
 -----------
 rx-gdbsim
hw/riscv/Kconfig +6 -0
index 28947ef..3292fae 100644
@@ -48,3 +48,9 @@ config RISCV_VIRT
     select PCI_EXPRESS_GENERIC_BRIDGE
     select PFLASH_CFI01
     select SIFIVE
+
+config MICROCHIP_PFSOC
+    bool
+    select HART
+    select SIFIVE
+    select UNIMP
hw/riscv/meson.build +1 -0
index 25af9db..cf1aa99 100644
@@ -16,5 +16,6 @@ riscv_ss.add(when: 'CONFIG_SIFIVE_U', if_true: files('sifive_u_otp.c'))
 riscv_ss.add(when: 'CONFIG_SIFIVE_U', if_true: files('sifive_u_prci.c'))
 riscv_ss.add(when: 'CONFIG_SPIKE', if_true: files('riscv_htif.c'))
 riscv_ss.add(when: 'CONFIG_SPIKE', if_true: files('spike.c'))
+riscv_ss.add(when: 'CONFIG_MICROCHIP_PFSOC', if_true: files('microchip_pfsoc.c'))
 
 hw_arch += {'riscv': riscv_ss}
Signature · 1 line
2.7.4
author
#5 lore raw

PATCH v2 5/16 hw/char: Add Microchip PolarFire SoC MMUART emulation

In reply to Bin Meng

From: Bin Meng <[email protected]>

Microchip PolarFire SoC MMUART is ns16550 compatible, with some additional registers. Create a simple MMUART model built on top of the existing ns16550 model.

---

Changes in v2:
- change to update hw/char/meson.build
- add impl.min_access_size and impl.max_access_size as part of MemoryRegionOps and remove the allignment check

 include/hw/char/mchp_pfsoc_mmuart.h | 61 ++++++++++++++++++++++++++
 hw/char/mchp_pfsoc_mmuart.c         | 86 +++++++++++++++++++++++++++++++++++++
 MAINTAINERS                         |  2 +
 hw/char/Kconfig                     |  3 ++
 hw/char/meson.build                 |  1 +
 5 files changed, 153 insertions(+)
 create mode 100644 include/hw/char/mchp_pfsoc_mmuart.h
 create mode 100644 hw/char/mchp_pfsoc_mmuart.c
include/hw/char/mchp_pfsoc_mmuart.h new file +61 -0
new file mode 100644
index 0000000..f619902
@@ -0,0 +1,61 @@
+/*
+ * Microchip PolarFire SoC MMUART emulation
+ *
+ * Copyright (c) 2020 Wind River Systems, Inc.
+ *
+ * Author:
+ *   Bin Meng <[email protected]>
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#ifndef HW_MCHP_PFSOC_MMUART_H
+#define HW_MCHP_PFSOC_MMUART_H
+
+#include "hw/char/serial.h"
+
+#define MCHP_PFSOC_MMUART_REG_SIZE  52
+
+typedef struct MchpPfSoCMMUartState {
+    MemoryRegion iomem;
+    hwaddr base;
+    qemu_irq irq;
+
+    SerialMM *serial;
+
+    uint32_t reg[MCHP_PFSOC_MMUART_REG_SIZE / sizeof(uint32_t)];
+} MchpPfSoCMMUartState;
+
+/**
+ * mchp_pfsoc_mmuart_create - Create a Microchip PolarFire SoC MMUART
+ *
+ * This is a helper routine for board to create a MMUART device that is
+ * compatible with Microchip PolarFire SoC.
+ *
+ * @sysmem: system memory region to map
+ * @base: base address of the MMUART registers
+ * @irq: IRQ number of the MMUART device
+ * @chr: character device to associate to
+ *
+ * @return: a pointer to the device specific control structure
+ */
+MchpPfSoCMMUartState *mchp_pfsoc_mmuart_create(MemoryRegion *sysmem,
+    hwaddr base, qemu_irq irq, Chardev *chr);
+
+#endif /* HW_MCHP_PFSOC_MMUART_H */
hw/char/mchp_pfsoc_mmuart.c new file +86 -0

86 lines not on this page · raw message

MAINTAINERS +2 -0
index 5359b39..4002d51 100644
@@ -1320,7 +1320,9 @@ M: Bin Meng <[email protected]>
 L: [email protected]
 S: Supported
 F: hw/riscv/microchip_pfsoc.c
+F: hw/char/mchp_pfsoc_mmuart.c
 F: include/hw/riscv/microchip_pfsoc.h
+F: include/hw/char/mchp_pfsoc_mmuart.h
 
 RX Machines
 -----------
hw/char/Kconfig +3 -0
index b7e0e4d..1d64555 100644
@@ -52,3 +52,6 @@ config RENESAS_SCI
 
 config AVR_USART
     bool
+
+config MCHP_PFSOC_MMUART
+    bool
hw/char/meson.build +1 -0
index e888215..ae27932 100644
@@ -32,6 +32,7 @@ softmmu_ss.add(when: 'CONFIG_RASPI', if_true: files('bcm2835_aux.c'))
 softmmu_ss.add(when: 'CONFIG_RENESAS_SCI', if_true: files('renesas_sci.c'))
 softmmu_ss.add(when: 'CONFIG_SH4', if_true: files('sh_serial.c'))
 softmmu_ss.add(when: 'CONFIG_STM32F2XX_USART', if_true: files('stm32f2xx_usart.c'))
+softmmu_ss.add(when: 'CONFIG_MCHP_PFSOC_MMUART', if_true: files('mchp_pfsoc_mmuart.c'))
 
 specific_ss.add(when: 'CONFIG_TERMINAL3270', if_true: files('terminal3270.c'))
 specific_ss.add(when: 'CONFIG_VIRTIO', if_true: files('virtio-serial-bus.c'))
Signature · 1 line
2.7.4
author
#6 lore raw

PATCH v2 6/16 hw/riscv: microchip_pfsoc: Connect 5 MMUARTs

In reply to Bin Meng

From: Bin Meng <[email protected]>

Microchip PolarFire SoC has 5 MMUARTs, and the Icicle Kit board wires 4 of them out. Let's connect all 5 MMUARTs.

---

(no changes since v1)

 include/hw/riscv/microchip_pfsoc.h | 20 ++++++++++++++++++++
 hw/riscv/microchip_pfsoc.c         | 30 ++++++++++++++++++++++++++++++
 hw/riscv/Kconfig                   |  1 +
 3 files changed, 51 insertions(+)
include/hw/riscv/microchip_pfsoc.h +20 -0
index 1953ef1..a5efa1d 100644
@@ -22,6 +22,8 @@
 #ifndef HW_MICROCHIP_PFSOC_H
 #define HW_MICROCHIP_PFSOC_H
 
+#include "hw/char/mchp_pfsoc_mmuart.h"
+
 typedef struct MicrochipPFSoCState {
     /*< private >*/
     DeviceState parent_obj;
@@ -32,6 +34,11 @@ typedef struct MicrochipPFSoCState {
     RISCVHartArrayState e_cpus;
     RISCVHartArrayState u_cpus;
     DeviceState *plic;
+    MchpPfSoCMMUartState *serial0;
+    MchpPfSoCMMUartState *serial1;
+    MchpPfSoCMMUartState *serial2;
+    MchpPfSoCMMUartState *serial3;
+    MchpPfSoCMMUartState *serial4;
 } MicrochipPFSoCState;
 
 #define TYPE_MICROCHIP_PFSOC    "microchip.pfsoc"
@@ -64,14 +71,27 @@ enum {
     MICROCHIP_PFSOC_L2CC,
     MICROCHIP_PFSOC_L2LIM,
     MICROCHIP_PFSOC_PLIC,
+    MICROCHIP_PFSOC_MMUART0,
     MICROCHIP_PFSOC_SYSREG,
     MICROCHIP_PFSOC_MPUCFG,
+    MICROCHIP_PFSOC_MMUART1,
+    MICROCHIP_PFSOC_MMUART2,
+    MICROCHIP_PFSOC_MMUART3,
+    MICROCHIP_PFSOC_MMUART4,
     MICROCHIP_PFSOC_ENVM_CFG,
     MICROCHIP_PFSOC_ENVM_DATA,
     MICROCHIP_PFSOC_IOSCB_CFG,
     MICROCHIP_PFSOC_DRAM,
 };
 
+enum {
+    MICROCHIP_PFSOC_MMUART0_IRQ = 90,
+    MICROCHIP_PFSOC_MMUART1_IRQ = 91,
+    MICROCHIP_PFSOC_MMUART2_IRQ = 92,
+    MICROCHIP_PFSOC_MMUART3_IRQ = 93,
+    MICROCHIP_PFSOC_MMUART4_IRQ = 94,
+};
+
 #define MICROCHIP_PFSOC_MANAGEMENT_CPU_COUNT    1
 #define MICROCHIP_PFSOC_COMPUTE_CPU_COUNT       4
 
hw/riscv/microchip_pfsoc.c +30 -0
index d946b2a..cee959a 100644
@@ -11,6 +11,7 @@
  * 0) CLINT (Core Level Interruptor)
  * 1) PLIC (Platform Level Interrupt Controller)
  * 2) eNVM (Embedded Non-Volatile Memory)
+ * 3) MMUARTs (Multi-Mode UART)
  *
  * This board currently generates devicetree dynamically that indicates at least
  * two harts and up to five harts.
@@ -38,6 +39,7 @@
 #include "hw/irq.h"
 #include "hw/loader.h"
 #include "hw/sysbus.h"
+#include "chardev/char.h"
 #include "hw/cpu/cluster.h"
 #include "target/riscv/cpu.h"
 #include "hw/misc/unimp.h"
@@ -46,6 +48,7 @@
 #include "hw/riscv/sifive_clint.h"
 #include "hw/riscv/sifive_plic.h"
 #include "hw/riscv/microchip_pfsoc.h"
+#include "sysemu/sysemu.h"
 
 /*
  * The BIOS image used by this machine is called Hart Software Services (HSS).
@@ -69,8 +72,13 @@ static const struct MemmapEntry {
     [MICROCHIP_PFSOC_L2CC] =            {  0x2010000,     0x1000 },
     [MICROCHIP_PFSOC_L2LIM] =           {  0x8000000,  0x2000000 },
     [MICROCHIP_PFSOC_PLIC] =            {  0xc000000,  0x4000000 },
+    [MICROCHIP_PFSOC_MMUART0] =         { 0x20000000,     0x1000 },
     [MICROCHIP_PFSOC_SYSREG] =          { 0x20002000,     0x2000 },
     [MICROCHIP_PFSOC_MPUCFG] =          { 0x20005000,     0x1000 },
+    [MICROCHIP_PFSOC_MMUART1] =         { 0x20100000,     0x1000 },
+    [MICROCHIP_PFSOC_MMUART2] =         { 0x20102000,     0x1000 },
+    [MICROCHIP_PFSOC_MMUART3] =         { 0x20104000,     0x1000 },
+    [MICROCHIP_PFSOC_MMUART4] =         { 0x20106000,     0x1000 },
     [MICROCHIP_PFSOC_ENVM_CFG] =        { 0x20200000,     0x1000 },
     [MICROCHIP_PFSOC_ENVM_DATA] =       { 0x20220000,    0x20000 },
     [MICROCHIP_PFSOC_IOSCB_CFG] =       { 0x37080000,     0x1000 },
@@ -215,6 +223,28 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
         memmap[MICROCHIP_PFSOC_MPUCFG].base,
         memmap[MICROCHIP_PFSOC_MPUCFG].size);
 
+    /* MMUARTs */
+    s->serial0 = mchp_pfsoc_mmuart_create(system_memory,
+        memmap[MICROCHIP_PFSOC_MMUART0].base,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_MMUART0_IRQ),
+        serial_hd(0));
+    s->serial1 = mchp_pfsoc_mmuart_create(system_memory,
+        memmap[MICROCHIP_PFSOC_MMUART1].base,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_MMUART1_IRQ),
+        serial_hd(1));
+    s->serial2 = mchp_pfsoc_mmuart_create(system_memory,
+        memmap[MICROCHIP_PFSOC_MMUART2].base,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_MMUART2_IRQ),
+        serial_hd(2));
+    s->serial3 = mchp_pfsoc_mmuart_create(system_memory,
+        memmap[MICROCHIP_PFSOC_MMUART3].base,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_MMUART3_IRQ),
+        serial_hd(3));
+    s->serial4 = mchp_pfsoc_mmuart_create(system_memory,
+        memmap[MICROCHIP_PFSOC_MMUART4].base,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_MMUART4_IRQ),
+        serial_hd(4));
+
     /* eNVM */
     memory_region_init_rom(envm_data, OBJECT(dev), "microchip.pfsoc.envm.data",
                            memmap[MICROCHIP_PFSOC_ENVM_DATA].size,
hw/riscv/Kconfig +1 -0
index 3292fae..ceb7c16 100644
@@ -54,3 +54,4 @@ config MICROCHIP_PFSOC
     select HART
     select SIFIVE
     select UNIMP
+    select MCHP_PFSOC_MMUART
Signature · 1 line
2.7.4
author
#7 lore raw

PATCH v2 7/16 hw/sd: Add Cadence SDHCI emulation

In reply to Bin Meng

From: Bin Meng <[email protected]>

Cadence SD/SDIO/eMMC Host Controller (SD4HC) is an SDHCI compatible controller. The SDHCI compatible registers start from offset 0x200, which are called Slot Register Set (SRS) in its datasheet.

This creates a Cadence SDHCI model built on top of the existing generic SDHCI model. Cadence specific Host Register Set (HRS) is implemented to make guest software happy.

---

Changes in v2:
- change to update hw/sd/meson.build
- change the name to "generic-sdhci" when calling object_initialize_child()
- add a container MR to simplify out-of-bounds access checks

 include/hw/sd/cadence_sdhci.h |  47 ++++++++++
 hw/sd/cadence_sdhci.c         | 193 ++++++++++++++++++++++++++++++++++++++++++
 hw/sd/Kconfig                 |   4 +
 hw/sd/meson.build             |   1 +
 4 files changed, 245 insertions(+)
 create mode 100644 include/hw/sd/cadence_sdhci.h
 create mode 100644 hw/sd/cadence_sdhci.c
include/hw/sd/cadence_sdhci.h new file +47 -0
new file mode 100644
index 0000000..cd8288b
@@ -0,0 +1,47 @@
+/*
+ * Cadence SDHCI emulation
+ *
+ * Copyright (c) 2020 Wind River Systems, Inc.
+ *
+ * Author:
+ *   Bin Meng <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 or
+ * (at your option) version 3 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef CADENCE_SDHCI_H
+#define CADENCE_SDHCI_H
+
+#include "hw/sd/sdhci.h"
+
+#define CADENCE_SDHCI_REG_SIZE  0x100
+#define CADENCE_SDHCI_NUM_REGS  (CADENCE_SDHCI_REG_SIZE / sizeof(uint32_t))
+
+typedef struct CadenceSDHCIState {
+    SysBusDevice parent;
+
+    MemoryRegion container;
+    MemoryRegion iomem;
+    BusState *bus;
+
+    uint32_t regs[CADENCE_SDHCI_NUM_REGS];
+
+    SDHCIState sdhci;
+} CadenceSDHCIState;
+
+#define TYPE_CADENCE_SDHCI  "cadence.sdhci"
+#define CADENCE_SDHCI(obj)  OBJECT_CHECK(CadenceSDHCIState, (obj), \
+                                         TYPE_CADENCE_SDHCI)
+
+#endif /* CADENCE_SDHCI_H */
hw/sd/cadence_sdhci.c new file +193 -0

193 lines not on this page · raw message

hw/sd/Kconfig +4 -0
index c5e1e55..633b9af 100644
@@ -19,3 +19,7 @@ config SDHCI_PCI
     default y if PCI_DEVICES
     depends on PCI
     select SDHCI
+
+config CADENCE_SDHCI
+    bool
+    select SDHCI
hw/sd/meson.build +1 -0
index b43e59b..9c29691 100644
@@ -10,3 +10,4 @@ softmmu_ss.add(when: 'CONFIG_PXA2XX', if_true: files('pxa2xx_mmci.c'))
 softmmu_ss.add(when: 'CONFIG_RASPI', if_true: files('bcm2835_sdhost.c'))
 softmmu_ss.add(when: 'CONFIG_ASPEED_SOC', if_true: files('aspeed_sdhci.c'))
 softmmu_ss.add(when: 'CONFIG_ALLWINNER_H3', if_true: files('allwinner-sdhost.c'))
+softmmu_ss.add(when: 'CONFIG_CADENCE_SDHCI', if_true: files('cadence_sdhci.c'))
Signature · 1 line
2.7.4
author
#8 lore raw

PATCH v2 8/16 hw/riscv: microchip_pfsoc: Connect a Cadence SDHCI controller and an SD card

In reply to Bin Meng

From: Bin Meng <[email protected]>

Microchip PolarFire SoC integrates one Cadence SDHCI controller. On the Icicle Kit board, one eMMC chip and an external SD card connect to this controller depending on different configuration.

As QEMU does not support eMMC yet, we just emulate the SD card configuration. To test this, the Hart Software Services (HSS) should choose the SD card configuration:

$ cp boards/icicle-kit-es/def_config.sdcard .config
$ make BOARD=icicle-kit-es

The SD card image can be built from the Yocto BSP at:
https://github.com/polarfire-soc/meta-polarfire-soc-yocto-bsp

Note the generated SD card image should be resized before use:

$ qemu-img resize /path/to/sdcard.img 4G

Launch QEMU with the following command:

$ qemu-system-riscv64 -nographic -M microchip-icicle-kit -sd sdcard.img

---

Changes in v2:
- do not initialize TYPE_SYSBUS_SDHCI in the SoC instance_init(), instead move that to the cadence_sdhci model
- do not access generic-sdhci's state directly,
instead move that to the cadence_sdhci model

 include/hw/riscv/microchip_pfsoc.h |  4 ++++
 hw/riscv/microchip_pfsoc.c         | 23 +++++++++++++++++++++++
 hw/riscv/Kconfig                   |  1 +
 3 files changed, 28 insertions(+)
include/hw/riscv/microchip_pfsoc.h +4 -0
index a5efa1d..d810ee8 100644
@@ -23,6 +23,7 @@
 #define HW_MICROCHIP_PFSOC_H
 
 #include "hw/char/mchp_pfsoc_mmuart.h"
+#include "hw/sd/cadence_sdhci.h"
 
 typedef struct MicrochipPFSoCState {
     /*< private >*/
@@ -39,6 +40,7 @@ typedef struct MicrochipPFSoCState {
     MchpPfSoCMMUartState *serial2;
     MchpPfSoCMMUartState *serial3;
     MchpPfSoCMMUartState *serial4;
+    CadenceSDHCIState sdhci;
 } MicrochipPFSoCState;
 
 #define TYPE_MICROCHIP_PFSOC    "microchip.pfsoc"
@@ -74,6 +76,7 @@ enum {
     MICROCHIP_PFSOC_MMUART0,
     MICROCHIP_PFSOC_SYSREG,
     MICROCHIP_PFSOC_MPUCFG,
+    MICROCHIP_PFSOC_EMMC_SD,
     MICROCHIP_PFSOC_MMUART1,
     MICROCHIP_PFSOC_MMUART2,
     MICROCHIP_PFSOC_MMUART3,
@@ -85,6 +88,7 @@ enum {
 };
 
 enum {
+    MICROCHIP_PFSOC_EMMC_SD_IRQ = 88,
     MICROCHIP_PFSOC_MMUART0_IRQ = 90,
     MICROCHIP_PFSOC_MMUART1_IRQ = 91,
     MICROCHIP_PFSOC_MMUART2_IRQ = 92,
hw/riscv/microchip_pfsoc.c +23 -0
index cee959a..0b2e9ca 100644
@@ -12,6 +12,7 @@
  * 1) PLIC (Platform Level Interrupt Controller)
  * 2) eNVM (Embedded Non-Volatile Memory)
  * 3) MMUARTs (Multi-Mode UART)
+ * 4) Cadence eMMC/SDHC controller and an SD card connected to it
  *
  * This board currently generates devicetree dynamically that indicates at least
  * two harts and up to five harts.
@@ -75,6 +76,7 @@ static const struct MemmapEntry {
     [MICROCHIP_PFSOC_MMUART0] =         { 0x20000000,     0x1000 },
     [MICROCHIP_PFSOC_SYSREG] =          { 0x20002000,     0x2000 },
     [MICROCHIP_PFSOC_MPUCFG] =          { 0x20005000,     0x1000 },
+    [MICROCHIP_PFSOC_EMMC_SD] =         { 0x20008000,     0x1000 },
     [MICROCHIP_PFSOC_MMUART1] =         { 0x20100000,     0x1000 },
     [MICROCHIP_PFSOC_MMUART2] =         { 0x20102000,     0x1000 },
     [MICROCHIP_PFSOC_MMUART3] =         { 0x20104000,     0x1000 },
@@ -111,6 +113,9 @@ static void microchip_pfsoc_soc_instance_init(Object *obj)
     qdev_prop_set_string(DEVICE(&s->u_cpus), "cpu-type",
                          TYPE_RISCV_CPU_SIFIVE_U54);
     qdev_prop_set_uint64(DEVICE(&s->u_cpus), "resetvec", RESET_VECTOR);
+
+    object_initialize_child(obj, "sd-controller", &s->sdhci,
+                            TYPE_CADENCE_SDHCI);
 }
 
 static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
@@ -223,6 +228,13 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
         memmap[MICROCHIP_PFSOC_MPUCFG].base,
         memmap[MICROCHIP_PFSOC_MPUCFG].size);
 
+    /* SDHCI */
+    sysbus_realize(SYS_BUS_DEVICE(&s->sdhci), errp);
+    sysbus_mmio_map(SYS_BUS_DEVICE(&s->sdhci), 0,
+                    memmap[MICROCHIP_PFSOC_EMMC_SD].base);
+    sysbus_connect_irq(SYS_BUS_DEVICE(&s->sdhci), 0,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_EMMC_SD_IRQ));
+
     /* MMUARTs */
     s->serial0 = mchp_pfsoc_mmuart_create(system_memory,
         memmap[MICROCHIP_PFSOC_MMUART0].base,
@@ -290,6 +302,7 @@ static void microchip_icicle_kit_machine_init(MachineState *machine)
     MicrochipIcicleKitState *s = MICROCHIP_ICICLE_KIT_MACHINE(machine);
     MemoryRegion *system_memory = get_system_memory();
     MemoryRegion *main_mem = g_new(MemoryRegion, 1);
+    DriveInfo *dinfo = drive_get_next(IF_SD);
 
     /* Sanity check on RAM size */
     if (machine->ram_size < mc->default_ram_size) {
@@ -312,6 +325,16 @@ static void microchip_icicle_kit_machine_init(MachineState *machine)
 
     /* Load the firmware */
     riscv_find_and_load_firmware(machine, BIOS_FILENAME, RESET_VECTOR, NULL);
+
+    /* Attach an SD card */
+    if (dinfo) {
+        CadenceSDHCIState *sdhci = &(s->soc.sdhci);
+        DeviceState *card = qdev_new(TYPE_SD_CARD);
+
+        qdev_prop_set_drive_err(card, "drive", blk_by_legacy_dinfo(dinfo),
+                                &error_fatal);
+        qdev_realize_and_unref(card, sdhci->bus, &error_fatal);
+    }
 }
 
 static void microchip_icicle_kit_machine_class_init(ObjectClass *oc, void *data)
hw/riscv/Kconfig +1 -0
index ceb7c16..7412db9 100644
@@ -55,3 +55,4 @@ config MICROCHIP_PFSOC
     select SIFIVE
     select UNIMP
     select MCHP_PFSOC_MMUART
+    select CADENCE_SDHCI
Signature · 1 line
2.7.4
author
#9 lore raw

PATCH v2 9/16 hw/dma: Add SiFive platform DMA controller emulation

In reply to Bin Meng

From: Bin Meng <[email protected]>

Microchip PolarFire SoC integrates a DMA engine that supports:
* Independent concurrent DMA transfers using 4 DMA channels
* Generation of interrupts on various conditions during execution which is actually an IP reused from the SiFive FU540 chip.

This creates a model to support both polling and interrupt modes.

---

Changes in v2:
- change to update hw/dma/meson.build
- rename the file names to sifive_pdma.[c|h]
- update irq number to 8 per the SiFive FU540 manual
- fix the register offset for channel 1/2/3 in the read/write ops

 include/hw/dma/sifive_pdma.h |  57 ++++++++
 hw/dma/sifive_pdma.c         | 313 +++++++++++++++++++++++++++++++++++++++++++
 hw/dma/Kconfig               |   3 +
 hw/dma/meson.build           |   1 +
 4 files changed, 374 insertions(+)
 create mode 100644 include/hw/dma/sifive_pdma.h
 create mode 100644 hw/dma/sifive_pdma.c
include/hw/dma/sifive_pdma.h new file +57 -0
new file mode 100644
index 0000000..fb09383
@@ -0,0 +1,57 @@
+/*
+ * SiFive Platform DMA emulation
+ *
+ * Copyright (c) 2020 Wind River Systems, Inc.
+ *
+ * Author:
+ *   Bin Meng <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 or
+ * (at your option) version 3 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef SIFIVE_PDMA_H
+#define SIFIVE_PDMA_H
+
+struct sifive_pdma_chan {
+    uint32_t control;
+    uint32_t next_config;
+    uint64_t next_bytes;
+    uint64_t next_dst;
+    uint64_t next_src;
+    uint32_t exec_config;
+    uint64_t exec_bytes;
+    uint64_t exec_dst;
+    uint64_t exec_src;
+    int state;
+};
+
+#define SIFIVE_PDMA_CHANS           4
+#define SIFIVE_PDMA_IRQS            (SIFIVE_PDMA_CHANS * 2)
+#define SIFIVE_PDMA_REG_SIZE        0x100000
+#define SIFIVE_PDMA_CHAN_NO(reg)    ((reg & (SIFIVE_PDMA_REG_SIZE - 1)) >> 12)
+
+typedef struct SiFivePDMAState {
+    SysBusDevice parent;
+    MemoryRegion iomem;
+    qemu_irq irq[SIFIVE_PDMA_IRQS];
+
+    struct sifive_pdma_chan chan[SIFIVE_PDMA_CHANS];
+} SiFivePDMAState;
+
+#define TYPE_SIFIVE_PDMA    "sifive.pdma"
+
+#define MCHP_PFSOC_DMA(obj) \
+    OBJECT_CHECK(SiFivePDMAState, (obj), TYPE_SIFIVE_PDMA)
+
+#endif /* SIFIVE_PDMA_H */
hw/dma/sifive_pdma.c new file +313 -0

313 lines not on this page · raw message

hw/dma/Kconfig +3 -0
index 5c61b67..d67492d 100644
@@ -20,3 +20,6 @@ config ZYNQ_DEVCFG
 
 config STP2000
     bool
+
+config SIFIVE_PDMA
+    bool
hw/dma/meson.build +1 -0
index ff5bb37..b991d76 100644
@@ -13,3 +13,4 @@ softmmu_ss.add(when: 'CONFIG_XLNX_ZYNQMP_ARM', if_true: files('xlnx-zdma.c'))
 softmmu_ss.add(when: 'CONFIG_OMAP', if_true: files('omap_dma.c', 'soc_dma.c'))
 softmmu_ss.add(when: 'CONFIG_PXA2XX', if_true: files('pxa2xx_dma.c'))
 softmmu_ss.add(when: 'CONFIG_RASPI', if_true: files('bcm2835_dma.c'))
+softmmu_ss.add(when: 'CONFIG_SIFIVE_PDMA', if_true: files('sifive_pdma.c'))
Signature · 1 line
2.7.4
author
#10 lore raw

PATCH v2 10/16 hw/riscv: microchip_pfsoc: Connect a DMA controller

In reply to Bin Meng

From: Bin Meng <[email protected]>

On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA controller to move the 2nd stage bootloader in the system memory. Let's connect a DMA controller to Microchip PolarFire SoC.

---

Changes in v2:
- connect 8 IRQs to the PLIC

 include/hw/riscv/microchip_pfsoc.h | 11 +++++++++++
 hw/riscv/microchip_pfsoc.c         | 15 +++++++++++++++
 hw/riscv/Kconfig                   |  1 +
 3 files changed, 27 insertions(+)
include/hw/riscv/microchip_pfsoc.h +11 -0
index d810ee8..63e7860 100644
@@ -23,6 +23,7 @@
 #define HW_MICROCHIP_PFSOC_H
 
 #include "hw/char/mchp_pfsoc_mmuart.h"
+#include "hw/dma/sifive_pdma.h"
 #include "hw/sd/cadence_sdhci.h"
 
 typedef struct MicrochipPFSoCState {
@@ -40,6 +41,7 @@ typedef struct MicrochipPFSoCState {
     MchpPfSoCMMUartState *serial2;
     MchpPfSoCMMUartState *serial3;
     MchpPfSoCMMUartState *serial4;
+    SiFivePDMAState dma;
     CadenceSDHCIState sdhci;
 } MicrochipPFSoCState;
 
@@ -71,6 +73,7 @@ enum {
     MICROCHIP_PFSOC_BUSERR_UNIT4,
     MICROCHIP_PFSOC_CLINT,
     MICROCHIP_PFSOC_L2CC,
+    MICROCHIP_PFSOC_DMA,
     MICROCHIP_PFSOC_L2LIM,
     MICROCHIP_PFSOC_PLIC,
     MICROCHIP_PFSOC_MMUART0,
@@ -88,6 +91,14 @@ enum {
 };
 
 enum {
+    MICROCHIP_PFSOC_DMA_IRQ0 = 5,
+    MICROCHIP_PFSOC_DMA_IRQ1 = 6,
+    MICROCHIP_PFSOC_DMA_IRQ2 = 7,
+    MICROCHIP_PFSOC_DMA_IRQ3 = 8,
+    MICROCHIP_PFSOC_DMA_IRQ4 = 9,
+    MICROCHIP_PFSOC_DMA_IRQ5 = 10,
+    MICROCHIP_PFSOC_DMA_IRQ6 = 11,
+    MICROCHIP_PFSOC_DMA_IRQ7 = 12,
     MICROCHIP_PFSOC_EMMC_SD_IRQ = 88,
     MICROCHIP_PFSOC_MMUART0_IRQ = 90,
     MICROCHIP_PFSOC_MMUART1_IRQ = 91,
hw/riscv/microchip_pfsoc.c +15 -0
index 0b2e9ca..d8ec973 100644
@@ -13,6 +13,7 @@
  * 2) eNVM (Embedded Non-Volatile Memory)
  * 3) MMUARTs (Multi-Mode UART)
  * 4) Cadence eMMC/SDHC controller and an SD card connected to it
+ * 5) SiFive Platform DMA (Direct Memory Access Controller)
  *
  * This board currently generates devicetree dynamically that indicates at least
  * two harts and up to five harts.
@@ -71,6 +72,7 @@ static const struct MemmapEntry {
     [MICROCHIP_PFSOC_BUSERR_UNIT4] =    {  0x1704000,     0x1000 },
     [MICROCHIP_PFSOC_CLINT] =           {  0x2000000,    0x10000 },
     [MICROCHIP_PFSOC_L2CC] =            {  0x2010000,     0x1000 },
+    [MICROCHIP_PFSOC_DMA] =             {  0x3000000,   0x100000 },
     [MICROCHIP_PFSOC_L2LIM] =           {  0x8000000,  0x2000000 },
     [MICROCHIP_PFSOC_PLIC] =            {  0xc000000,  0x4000000 },
     [MICROCHIP_PFSOC_MMUART0] =         { 0x20000000,     0x1000 },
@@ -114,6 +116,9 @@ static void microchip_pfsoc_soc_instance_init(Object *obj)
                          TYPE_RISCV_CPU_SIFIVE_U54);
     qdev_prop_set_uint64(DEVICE(&s->u_cpus), "resetvec", RESET_VECTOR);
 
+    object_initialize_child(obj, "dma-controller", &s->dma,
+                            TYPE_SIFIVE_PDMA);
+
     object_initialize_child(obj, "sd-controller", &s->sdhci,
                             TYPE_CADENCE_SDHCI);
 }
@@ -218,6 +223,16 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
         memmap[MICROCHIP_PFSOC_PLIC].size);
     g_free(plic_hart_config);
 
+    /* DMA */
+    sysbus_realize(SYS_BUS_DEVICE(&s->dma), errp);
+    sysbus_mmio_map(SYS_BUS_DEVICE(&s->dma), 0,
+                    memmap[MICROCHIP_PFSOC_DMA].base);
+    for (i = 0; i < SIFIVE_PDMA_IRQS; i++) {
+        sysbus_connect_irq(SYS_BUS_DEVICE(&s->dma), i,
+                           qdev_get_gpio_in(DEVICE(s->plic),
+                                            MICROCHIP_PFSOC_DMA_IRQ0 + i));
+    }
+
     /* SYSREG */
     create_unimplemented_device("microchip.pfsoc.sysreg",
         memmap[MICROCHIP_PFSOC_SYSREG].base,
hw/riscv/Kconfig +1 -0
index 7412db9..9032cb0 100644
@@ -55,4 +55,5 @@ config MICROCHIP_PFSOC
     select SIFIVE
     select UNIMP
     select MCHP_PFSOC_MMUART
+    select SIFIVE_PDMA
     select CADENCE_SDHCI
Signature · 1 line
2.7.4
author
#11 lore raw

PATCH v2 11/16 hw/net: cadence_gem: Add a new 'phy-addr' property

In reply to Bin Meng

From: Bin Meng <[email protected]>

At present the PHY address of the PHY connected to GEM is hard-coded to either 23 (BOARD_PHY_ADDRESS) or 0. This might not be the case for all boards. Add a new 'phy-addr' property so that board can specify the PHY address for each GEM instance.

---

Changes in v2:
- change "phy-addr" default value to BOARD_PHY_ADDRESS

 include/hw/net/cadence_gem.h | 2 ++
 hw/net/cadence_gem.c         | 5 +++--
 2 files changed, 5 insertions(+), 2 deletions(-)
include/hw/net/cadence_gem.h +2 -0
index 54e646f..01c6189 100644
@@ -73,6 +73,8 @@ typedef struct CadenceGEMState {
     /* Mask of register bits which are write 1 to clear */
     uint32_t regs_w1c[CADENCE_GEM_MAXREG];
 
+    /* PHY address */
+    uint8_t phy_addr;
     /* PHY registers backing store */
     uint16_t phy_regs[32];
 
hw/net/cadence_gem.c +3 -2
index a93b5c0..d80096b 100644
@@ -1446,7 +1446,7 @@ static uint64_t gem_read(void *opaque, hwaddr offset, unsigned size)
             uint32_t phy_addr, reg_num;
 
             phy_addr = (retval & GEM_PHYMNTNC_ADDR) >> GEM_PHYMNTNC_ADDR_SHFT;
-            if (phy_addr == BOARD_PHY_ADDRESS || phy_addr == 0) {
+            if (phy_addr == s->phy_addr || phy_addr == 0) {
                 reg_num = (retval & GEM_PHYMNTNC_REG) >> GEM_PHYMNTNC_REG_SHIFT;
                 retval &= 0xFFFF0000;
                 retval |= gem_phy_read(s, reg_num);
@@ -1569,7 +1569,7 @@ static void gem_write(void *opaque, hwaddr offset, uint64_t val,
             uint32_t phy_addr, reg_num;
 
             phy_addr = (val & GEM_PHYMNTNC_ADDR) >> GEM_PHYMNTNC_ADDR_SHFT;
-            if (phy_addr == BOARD_PHY_ADDRESS || phy_addr == 0) {
+            if (phy_addr == s->phy_addr || phy_addr == 0) {
                 reg_num = (val & GEM_PHYMNTNC_REG) >> GEM_PHYMNTNC_REG_SHIFT;
                 gem_phy_write(s, reg_num, val);
             }
@@ -1682,6 +1682,7 @@ static Property gem_properties[] = {
     DEFINE_NIC_PROPERTIES(CadenceGEMState, conf),
     DEFINE_PROP_UINT32("revision", CadenceGEMState, revision,
                        GEM_MODID_VALUE),
+    DEFINE_PROP_UINT8("phy-addr", CadenceGEMState, phy_addr, BOARD_PHY_ADDRESS),
     DEFINE_PROP_UINT8("num-priority-queues", CadenceGEMState,
                       num_priority_queues, 1),
     DEFINE_PROP_UINT8("num-type1-screeners", CadenceGEMState,
Signature · 1 line
2.7.4
author
#12 lore raw

PATCH v2 12/16 hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23

In reply to Bin Meng

From: Bin Meng <[email protected]>

When cadence_gem model was created for Xilinx boards, the PHY address was hard-coded to 23 in the GEM model. Now that we have introduced a property we can use that to tell GEM model what our PHY address is. Change all boards' GEM 'phy-addr' property value to 23, and set the PHY address default value to 0 in the GEM model.

---

(no changes since v1)

 hw/arm/xilinx_zynq.c | 1 +
 hw/arm/xlnx-versal.c | 1 +
 hw/arm/xlnx-zynqmp.c | 1 +
 hw/net/cadence_gem.c | 6 +++---
 4 files changed, 6 insertions(+), 3 deletions(-)
hw/arm/xilinx_zynq.c +1 -0
index 969ef07..9ffcc56 100644
@@ -119,6 +119,7 @@ static void gem_init(NICInfo *nd, uint32_t base, qemu_irq irq)
         qemu_check_nic_model(nd, TYPE_CADENCE_GEM);
         qdev_set_nic_properties(dev, nd);
     }
+    object_property_set_int(OBJECT(dev), "phy-addr", 23, &error_abort);
     s = SYS_BUS_DEVICE(dev);
     sysbus_realize_and_unref(s, &error_fatal);
     sysbus_mmio_map(s, 0, base);
hw/arm/xlnx-versal.c +1 -0
index e3aa4bd..12ba6c4 100644
@@ -165,6 +165,7 @@ static void versal_create_gems(Versal *s, qemu_irq *pic)
             qemu_check_nic_model(nd, "cadence_gem");
             qdev_set_nic_properties(dev, nd);
         }
+        object_property_set_int(OBJECT(dev), "phy-addr", 23, &error_abort);
         object_property_set_int(OBJECT(dev), "num-priority-queues", 2,
                                 &error_abort);
         object_property_set_link(OBJECT(dev), "dma", OBJECT(&s->mr_ps),
hw/arm/xlnx-zynqmp.c +1 -0
index c435b9d..a85ef4b 100644
@@ -460,6 +460,7 @@ static void xlnx_zynqmp_realize(DeviceState *dev, Error **errp)
         }
         object_property_set_int(OBJECT(&s->gem[i]), "revision", GEM_REVISION,
                                 &error_abort);
+        object_property_set_int(OBJECT(dev), "phy-addr", 23, &error_abort);
         object_property_set_int(OBJECT(&s->gem[i]), "num-priority-queues", 2,
                                 &error_abort);
         if (!sysbus_realize(SYS_BUS_DEVICE(&s->gem[i]), errp)) {
hw/net/cadence_gem.c +3 -3
index d80096b..7a53469 100644
@@ -250,7 +250,7 @@
 #define GEM_PHYMNTNC_REG_SHIFT 18
 
 /* Marvell PHY definitions */
-#define BOARD_PHY_ADDRESS    23 /* PHY address we will emulate a device at */
+#define BOARD_PHY_ADDRESS    0 /* PHY address we will emulate a device at */
 
 #define PHY_REG_CONTROL      0
 #define PHY_REG_STATUS       1
@@ -1446,7 +1446,7 @@ static uint64_t gem_read(void *opaque, hwaddr offset, unsigned size)
             uint32_t phy_addr, reg_num;
 
             phy_addr = (retval & GEM_PHYMNTNC_ADDR) >> GEM_PHYMNTNC_ADDR_SHFT;
-            if (phy_addr == s->phy_addr || phy_addr == 0) {
+            if (phy_addr == s->phy_addr) {
                 reg_num = (retval & GEM_PHYMNTNC_REG) >> GEM_PHYMNTNC_REG_SHIFT;
                 retval &= 0xFFFF0000;
                 retval |= gem_phy_read(s, reg_num);
@@ -1569,7 +1569,7 @@ static void gem_write(void *opaque, hwaddr offset, uint64_t val,
             uint32_t phy_addr, reg_num;
 
             phy_addr = (val & GEM_PHYMNTNC_ADDR) >> GEM_PHYMNTNC_ADDR_SHFT;
-            if (phy_addr == s->phy_addr || phy_addr == 0) {
+            if (phy_addr == s->phy_addr) {
                 reg_num = (val & GEM_PHYMNTNC_REG) >> GEM_PHYMNTNC_REG_SHIFT;
                 gem_phy_write(s, reg_num, val);
             }
Signature · 1 line
2.7.4
author
#13 lore raw

PATCH v2 13/16 hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs

In reply to Bin Meng

From: Bin Meng <[email protected]>

Microchip PolarFire SoC integrates 2 Candence GEMs to provide IEEE 802.3 standard-compliant 10/100/1000 Mbps ethernet interface.

On the Icicle Kit board, GEM0 connects to a PHY at address 8 while GEM1 connects to a PHY at address 9.

The 2nd stage bootloader (U-Boot) is using GEM1 by default, so we must specify 2 '-nic' options from the command line in order to get a working ethernet.

---

(no changes since v1)

 include/hw/riscv/microchip_pfsoc.h |  7 +++++++
 hw/riscv/microchip_pfsoc.c         | 39 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 46 insertions(+)
include/hw/riscv/microchip_pfsoc.h +7 -0
index 63e7860..6d20853 100644
@@ -24,6 +24,7 @@
 
 #include "hw/char/mchp_pfsoc_mmuart.h"
 #include "hw/dma/sifive_pdma.h"
+#include "hw/net/cadence_gem.h"
 #include "hw/sd/cadence_sdhci.h"
 
 typedef struct MicrochipPFSoCState {
@@ -42,6 +43,8 @@ typedef struct MicrochipPFSoCState {
     MchpPfSoCMMUartState *serial3;
     MchpPfSoCMMUartState *serial4;
     SiFivePDMAState dma;
+    CadenceGEMState gem0;
+    CadenceGEMState gem1;
     CadenceSDHCIState sdhci;
 } MicrochipPFSoCState;
 
@@ -84,6 +87,8 @@ enum {
     MICROCHIP_PFSOC_MMUART2,
     MICROCHIP_PFSOC_MMUART3,
     MICROCHIP_PFSOC_MMUART4,
+    MICROCHIP_PFSOC_GEM0,
+    MICROCHIP_PFSOC_GEM1,
     MICROCHIP_PFSOC_ENVM_CFG,
     MICROCHIP_PFSOC_ENVM_DATA,
     MICROCHIP_PFSOC_IOSCB_CFG,
@@ -99,6 +104,8 @@ enum {
     MICROCHIP_PFSOC_DMA_IRQ5 = 10,
     MICROCHIP_PFSOC_DMA_IRQ6 = 11,
     MICROCHIP_PFSOC_DMA_IRQ7 = 12,
+    MICROCHIP_PFSOC_GEM0_IRQ = 64,
+    MICROCHIP_PFSOC_GEM1_IRQ = 70,
     MICROCHIP_PFSOC_EMMC_SD_IRQ = 88,
     MICROCHIP_PFSOC_MMUART0_IRQ = 90,
     MICROCHIP_PFSOC_MMUART1_IRQ = 91,
hw/riscv/microchip_pfsoc.c +39 -0
index d8ec973..7f25609 100644
@@ -14,6 +14,7 @@
  * 3) MMUARTs (Multi-Mode UART)
  * 4) Cadence eMMC/SDHC controller and an SD card connected to it
  * 5) SiFive Platform DMA (Direct Memory Access Controller)
+ * 6) GEM (Gigabit Ethernet MAC Controller)
  *
  * This board currently generates devicetree dynamically that indicates at least
  * two harts and up to five harts.
@@ -59,6 +60,9 @@
 #define BIOS_FILENAME   "hss.bin"
 #define RESET_VECTOR    0x20220000
 
+/* GEM version */
+#define GEM_REVISION    0x0107010c
+
 static const struct MemmapEntry {
     hwaddr base;
     hwaddr size;
@@ -83,6 +87,8 @@ static const struct MemmapEntry {
     [MICROCHIP_PFSOC_MMUART2] =         { 0x20102000,     0x1000 },
     [MICROCHIP_PFSOC_MMUART3] =         { 0x20104000,     0x1000 },
     [MICROCHIP_PFSOC_MMUART4] =         { 0x20106000,     0x1000 },
+    [MICROCHIP_PFSOC_GEM0] =            { 0x20110000,     0x2000 },
+    [MICROCHIP_PFSOC_GEM1] =            { 0x20112000,     0x2000 },
     [MICROCHIP_PFSOC_ENVM_CFG] =        { 0x20200000,     0x1000 },
     [MICROCHIP_PFSOC_ENVM_DATA] =       { 0x20220000,    0x20000 },
     [MICROCHIP_PFSOC_IOSCB_CFG] =       { 0x37080000,     0x1000 },
@@ -119,6 +125,9 @@ static void microchip_pfsoc_soc_instance_init(Object *obj)
     object_initialize_child(obj, "dma-controller", &s->dma,
                             TYPE_SIFIVE_PDMA);
 
+    object_initialize_child(obj, "gem0", &s->gem0, TYPE_CADENCE_GEM);
+    object_initialize_child(obj, "gem1", &s->gem1, TYPE_CADENCE_GEM);
+
     object_initialize_child(obj, "sd-controller", &s->sdhci,
                             TYPE_CADENCE_SDHCI);
 }
@@ -134,6 +143,7 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
     MemoryRegion *envm_data = g_new(MemoryRegion, 1);
     char *plic_hart_config;
     size_t plic_hart_config_len;
+    NICInfo *nd;
     int i;
 
     sysbus_realize(SYS_BUS_DEVICE(&s->e_cpus), &error_abort);
@@ -272,6 +282,35 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
         qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_MMUART4_IRQ),
         serial_hd(4));
 
+    /* GEMs */
+
+    nd = &nd_table[0];
+    if (nd->used) {
+        qemu_check_nic_model(nd, TYPE_CADENCE_GEM);
+        qdev_set_nic_properties(DEVICE(&s->gem0), nd);
+    }
+    nd = &nd_table[1];
+    if (nd->used) {
+        qemu_check_nic_model(nd, TYPE_CADENCE_GEM);
+        qdev_set_nic_properties(DEVICE(&s->gem1), nd);
+    }
+
+    object_property_set_int(OBJECT(&s->gem0), "revision", GEM_REVISION, errp);
+    object_property_set_int(OBJECT(&s->gem0), "phy-addr", 8, errp);
+    sysbus_realize(SYS_BUS_DEVICE(&s->gem0), errp);
+    sysbus_mmio_map(SYS_BUS_DEVICE(&s->gem0), 0,
+                    memmap[MICROCHIP_PFSOC_GEM0].base);
+    sysbus_connect_irq(SYS_BUS_DEVICE(&s->gem0), 0,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_GEM0_IRQ));
+
+    object_property_set_int(OBJECT(&s->gem1), "revision", GEM_REVISION, errp);
+    object_property_set_int(OBJECT(&s->gem1), "phy-addr", 9, errp);
+    sysbus_realize(SYS_BUS_DEVICE(&s->gem1), errp);
+    sysbus_mmio_map(SYS_BUS_DEVICE(&s->gem1), 0,
+                    memmap[MICROCHIP_PFSOC_GEM1].base);
+    sysbus_connect_irq(SYS_BUS_DEVICE(&s->gem1), 0,
+        qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_GEM1_IRQ));
+
     /* eNVM */
     memory_region_init_rom(envm_data, OBJECT(dev), "microchip.pfsoc.envm.data",
                            memmap[MICROCHIP_PFSOC_ENVM_DATA].size,
Signature · 1 line
2.7.4
author
#14 lore raw

PATCH v2 14/16 hw/riscv: microchip_pfsoc: Hook GPIO controllers

In reply to Bin Meng

From: Bin Meng <[email protected]>

Microchip PolarFire SoC integrates 3 GPIOs controllers. It seems enough to create unimplemented devices to cover their register spaces at this point.

With this commit, QEMU can boot to U-Boot (2nd stage bootloader) all the way to the Linux shell login prompt, with a modified HSS (1st stage bootloader).

For detailed instructions on how to create images for the Icicle Kit board, please check QEMU RISC-V WiKi page at:
https://wiki.qemu.org/Documentation/Platforms/RISCV

---

(no changes since v1)

 include/hw/riscv/microchip_pfsoc.h |  3 +++
 hw/riscv/microchip_pfsoc.c         | 14 ++++++++++++++
 2 files changed, 17 insertions(+)
include/hw/riscv/microchip_pfsoc.h +3 -0
index 6d20853..8bfc7e1 100644
@@ -89,6 +89,9 @@ enum {
     MICROCHIP_PFSOC_MMUART4,
     MICROCHIP_PFSOC_GEM0,
     MICROCHIP_PFSOC_GEM1,
+    MICROCHIP_PFSOC_GPIO0,
+    MICROCHIP_PFSOC_GPIO1,
+    MICROCHIP_PFSOC_GPIO2,
     MICROCHIP_PFSOC_ENVM_CFG,
     MICROCHIP_PFSOC_ENVM_DATA,
     MICROCHIP_PFSOC_IOSCB_CFG,
hw/riscv/microchip_pfsoc.c +14 -0
index 7f25609..11ebdd1 100644
@@ -89,6 +89,9 @@ static const struct MemmapEntry {
     [MICROCHIP_PFSOC_MMUART4] =         { 0x20106000,     0x1000 },
     [MICROCHIP_PFSOC_GEM0] =            { 0x20110000,     0x2000 },
     [MICROCHIP_PFSOC_GEM1] =            { 0x20112000,     0x2000 },
+    [MICROCHIP_PFSOC_GPIO0] =           { 0x20120000,     0x1000 },
+    [MICROCHIP_PFSOC_GPIO1] =           { 0x20121000,     0x1000 },
+    [MICROCHIP_PFSOC_GPIO2] =           { 0x20122000,     0x1000 },
     [MICROCHIP_PFSOC_ENVM_CFG] =        { 0x20200000,     0x1000 },
     [MICROCHIP_PFSOC_ENVM_DATA] =       { 0x20220000,    0x20000 },
     [MICROCHIP_PFSOC_IOSCB_CFG] =       { 0x37080000,     0x1000 },
@@ -311,6 +314,17 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
     sysbus_connect_irq(SYS_BUS_DEVICE(&s->gem1), 0,
         qdev_get_gpio_in(DEVICE(s->plic), MICROCHIP_PFSOC_GEM1_IRQ));
 
+    /* GPIOs */
+    create_unimplemented_device("microchip.pfsoc.gpio0",
+        memmap[MICROCHIP_PFSOC_GPIO0].base,
+        memmap[MICROCHIP_PFSOC_GPIO0].size);
+    create_unimplemented_device("microchip.pfsoc.gpio1",
+        memmap[MICROCHIP_PFSOC_GPIO1].base,
+        memmap[MICROCHIP_PFSOC_GPIO1].size);
+    create_unimplemented_device("microchip.pfsoc.gpio2",
+        memmap[MICROCHIP_PFSOC_GPIO2].base,
+        memmap[MICROCHIP_PFSOC_GPIO2].size);
+
     /* eNVM */
     memory_region_init_rom(envm_data, OBJECT(dev), "microchip.pfsoc.envm.data",
                            memmap[MICROCHIP_PFSOC_ENVM_DATA].size,
Signature · 1 line
2.7.4
author
#15 lore raw

PATCH v2 15/16 hw/riscv: clint: Avoid using hard-coded timebase frequency

In reply to Bin Meng

From: Bin Meng <[email protected]>

At present the CLINT timestamp is using a hard-coded timebase frequency value SIFIVE_CLINT_TIMEBASE_FREQ. This might not be true for all boards.

Add a new 'timebase-freq' property to the CLINT device, and update various functions to accept this as a parameter.

---

(no changes since v1)

 include/hw/riscv/sifive_clint.h |  4 +++-
 target/riscv/cpu.h              |  6 ++++--
 hw/riscv/microchip_pfsoc.c      |  6 +++++-
 hw/riscv/sifive_clint.c         | 26 +++++++++++++++-----------
 hw/riscv/sifive_e.c             |  3 ++-
 hw/riscv/sifive_u.c             |  3 ++-
 hw/riscv/spike.c                |  3 ++-
 hw/riscv/virt.c                 |  3 ++-
 target/riscv/cpu_helper.c       |  4 +++-
 target/riscv/csr.c              |  4 ++--
 10 files changed, 40 insertions(+), 22 deletions(-)
include/hw/riscv/sifive_clint.h +3 -1
index 9f5fb3d..a30be0f 100644
@@ -39,11 +39,13 @@ typedef struct SiFiveCLINTState {
     uint32_t timecmp_base;
     uint32_t time_base;
     uint32_t aperture_size;
+    uint32_t timebase_freq;
 } SiFiveCLINTState;
 
 DeviceState *sifive_clint_create(hwaddr addr, hwaddr size,
     uint32_t hartid_base, uint32_t num_harts, uint32_t sip_base,
-    uint32_t timecmp_base, uint32_t time_base, bool provide_rdtime);
+    uint32_t timecmp_base, uint32_t time_base, uint32_t timebase_freq,
+    bool provide_rdtime);
 
 enum {
     SIFIVE_SIP_BASE     = 0x0,
target/riscv/cpu.h +4 -2
index dc350f0..a003d83 100644
@@ -219,7 +219,8 @@ struct CPURISCVState {
     pmp_table_t pmp_state;
 
     /* machine specific rdtime callback */
-    uint64_t (*rdtime_fn)(void);
+    uint64_t (*rdtime_fn)(uint32_t);
+    uint32_t rdtime_fn_arg;
 
     /* True if in debugger mode.  */
     bool debugger;
@@ -349,7 +350,8 @@ void riscv_cpu_swap_hypervisor_regs(CPURISCVState *env);
 int riscv_cpu_claim_interrupts(RISCVCPU *cpu, uint32_t interrupts);
 uint32_t riscv_cpu_update_mip(RISCVCPU *cpu, uint32_t mask, uint32_t value);
 #define BOOL_TO_MASK(x) (-!!(x)) /* helper for riscv_cpu_update_mip value */
-void riscv_cpu_set_rdtime_fn(CPURISCVState *env, uint64_t (*fn)(void));
+void riscv_cpu_set_rdtime_fn(CPURISCVState *env, uint64_t (*fn)(uint32_t),
+                             uint32_t arg);
 #endif
 void riscv_cpu_set_mode(CPURISCVState *env, target_ulong newpriv);
 
hw/riscv/microchip_pfsoc.c +5 -1
index 11ebdd1..da6bd29 100644
@@ -60,6 +60,9 @@
 #define BIOS_FILENAME   "hss.bin"
 #define RESET_VECTOR    0x20220000
 
+/* CLINT timebase frequency */
+#define CLINT_TIMEBASE_FREQ 1000000
+
 /* GEM version */
 #define GEM_REVISION    0x0107010c
 
@@ -187,7 +190,8 @@ static void microchip_pfsoc_soc_realize(DeviceState *dev, Error **errp)
     /* CLINT */
     sifive_clint_create(memmap[MICROCHIP_PFSOC_CLINT].base,
         memmap[MICROCHIP_PFSOC_CLINT].size, 0, ms->smp.cpus,
-        SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE, false);
+        SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE,
+        CLINT_TIMEBASE_FREQ, false);
 
     /* L2 cache controller */
     create_unimplemented_device("microchip.pfsoc.l2cc",
hw/riscv/sifive_clint.c +15 -11
index 15e13d5..fa1ddf2 100644
@@ -29,22 +29,23 @@
 #include "hw/riscv/sifive_clint.h"
 #include "qemu/timer.h"
 
-static uint64_t cpu_riscv_read_rtc(void)
+static uint64_t cpu_riscv_read_rtc(uint32_t timebase_freq)
 {
     return muldiv64(qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL),
-        SIFIVE_CLINT_TIMEBASE_FREQ, NANOSECONDS_PER_SECOND);
+        timebase_freq, NANOSECONDS_PER_SECOND);
 }
 
 /*
  * Called when timecmp is written to update the QEMU timer or immediately
  * trigger timer interrupt if mtimecmp <= current timer value.
  */
-static void sifive_clint_write_timecmp(RISCVCPU *cpu, uint64_t value)
+static void sifive_clint_write_timecmp(RISCVCPU *cpu, uint64_t value,
+                                       uint32_t timebase_freq)
 {
     uint64_t next;
     uint64_t diff;
 
-    uint64_t rtc_r = cpu_riscv_read_rtc();
+    uint64_t rtc_r = cpu_riscv_read_rtc(timebase_freq);
 
     cpu->env.timecmp = value;
     if (cpu->env.timecmp <= rtc_r) {
@@ -59,7 +60,7 @@ static void sifive_clint_write_timecmp(RISCVCPU *cpu, uint64_t value)
     diff = cpu->env.timecmp - rtc_r;
     /* back to ns (note args switched in muldiv64) */
     next = qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
-        muldiv64(diff, NANOSECONDS_PER_SECOND, SIFIVE_CLINT_TIMEBASE_FREQ);
+        muldiv64(diff, NANOSECONDS_PER_SECOND, timebase_freq);
     timer_mod(cpu->env.timer, next);
 }
 
@@ -112,10 +113,10 @@ static uint64_t sifive_clint_read(void *opaque, hwaddr addr, unsigned size)
         }
     } else if (addr == clint->time_base) {
         /* time_lo */
-        return cpu_riscv_read_rtc() & 0xFFFFFFFF;
+        return cpu_riscv_read_rtc(clint->timebase_freq) & 0xFFFFFFFF;
     } else if (addr == clint->time_base + 4) {
         /* time_hi */
-        return (cpu_riscv_read_rtc() >> 32) & 0xFFFFFFFF;
+        return (cpu_riscv_read_rtc(clint->timebase_freq) >> 32) & 0xFFFFFFFF;
     }
 
     error_report("clint: invalid read: %08x", (uint32_t)addr);
@@ -153,13 +154,13 @@ static void sifive_clint_write(void *opaque, hwaddr addr, uint64_t value,
             /* timecmp_lo */
             uint64_t timecmp_hi = env->timecmp >> 32;
             sifive_clint_write_timecmp(RISCV_CPU(cpu),
-                timecmp_hi << 32 | (value & 0xFFFFFFFF));
+                timecmp_hi << 32 | (value & 0xFFFFFFFF), clint->timebase_freq);
             return;
         } else if ((addr & 0x7) == 4) {
             /* timecmp_hi */
             uint64_t timecmp_lo = env->timecmp;
             sifive_clint_write_timecmp(RISCV_CPU(cpu),
-                value << 32 | (timecmp_lo & 0xFFFFFFFF));
+                value << 32 | (timecmp_lo & 0xFFFFFFFF), clint->timebase_freq);
         } else {
             error_report("clint: invalid timecmp write: %08x", (uint32_t)addr);
         }
@@ -194,6 +195,7 @@ static Property sifive_clint_properties[] = {
     DEFINE_PROP_UINT32("timecmp-base", SiFiveCLINTState, timecmp_base, 0),
     DEFINE_PROP_UINT32("time-base", SiFiveCLINTState, time_base, 0),
     DEFINE_PROP_UINT32("aperture-size", SiFiveCLINTState, aperture_size, 0),
+    DEFINE_PROP_UINT32("timebase-freq", SiFiveCLINTState, timebase_freq, 0),
     DEFINE_PROP_END_OF_LIST(),
 };
 
@@ -232,7 +234,8 @@ type_init(sifive_clint_register_types)
  */
 DeviceState *sifive_clint_create(hwaddr addr, hwaddr size,
     uint32_t hartid_base, uint32_t num_harts, uint32_t sip_base,
-    uint32_t timecmp_base, uint32_t time_base, bool provide_rdtime)
+    uint32_t timecmp_base, uint32_t time_base, uint32_t timebase_freq,
+    bool provide_rdtime)
 {
     int i;
     for (i = 0; i < num_harts; i++) {
@@ -242,7 +245,7 @@ DeviceState *sifive_clint_create(hwaddr addr, hwaddr size,
             continue;
         }
         if (provide_rdtime) {
-            riscv_cpu_set_rdtime_fn(env, cpu_riscv_read_rtc);
+            riscv_cpu_set_rdtime_fn(env, cpu_riscv_read_rtc, timebase_freq);
         }
         env->timer = timer_new_ns(QEMU_CLOCK_VIRTUAL,
                                   &sifive_clint_timer_cb, cpu);
@@ -256,6 +259,7 @@ DeviceState *sifive_clint_create(hwaddr addr, hwaddr size,
     qdev_prop_set_uint32(dev, "timecmp-base", timecmp_base);
     qdev_prop_set_uint32(dev, "time-base", time_base);
     qdev_prop_set_uint32(dev, "aperture-size", size);
+    qdev_prop_set_uint32(dev, "timebase-freq", timebase_freq);
     sysbus_realize_and_unref(SYS_BUS_DEVICE(dev), &error_fatal);
     sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, addr);
     return dev;
hw/riscv/sifive_e.c +2 -1
index cd7560d..36ccfb2 100644
@@ -213,7 +213,8 @@ static void sifive_e_soc_realize(DeviceState *dev, Error **errp)
         memmap[SIFIVE_E_PLIC].size);
     sifive_clint_create(memmap[SIFIVE_E_CLINT].base,
         memmap[SIFIVE_E_CLINT].size, 0, ms->smp.cpus,
-        SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE, false);
+        SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE,
+        SIFIVE_CLINT_TIMEBASE_FREQ, false);
     create_unimplemented_device("riscv.sifive.e.aon",
         memmap[SIFIVE_E_AON].base, memmap[SIFIVE_E_AON].size);
     sifive_e_prci_create(memmap[SIFIVE_E_PRCI].base);
hw/riscv/sifive_u.c +2 -1
index 404d5e6..2bc3992 100644
@@ -706,7 +706,8 @@ static void sifive_u_soc_realize(DeviceState *dev, Error **errp)
         serial_hd(1), qdev_get_gpio_in(DEVICE(s->plic), SIFIVE_U_UART1_IRQ));
     sifive_clint_create(memmap[SIFIVE_U_CLINT].base,
         memmap[SIFIVE_U_CLINT].size, 0, ms->smp.cpus,
-        SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE, false);
+        SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE,
+        SIFIVE_CLINT_TIMEBASE_FREQ, false);
 
     if (!sysbus_realize(SYS_BUS_DEVICE(&s->prci), errp)) {
         return;
hw/riscv/spike.c +2 -1
index 56f5fe7..b54a396 100644
@@ -242,7 +242,8 @@ static void spike_board_init(MachineState *machine)
         sifive_clint_create(
             memmap[SPIKE_CLINT].base + i * memmap[SPIKE_CLINT].size,
             memmap[SPIKE_CLINT].size, base_hartid, hart_count,
-            SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE, false);
+            SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE,
+            SIFIVE_CLINT_TIMEBASE_FREQ, false);
     }
 
     /* register system main memory (actual RAM) */
hw/riscv/virt.c +2 -1
index 6fca513..c67a910 100644
@@ -541,7 +541,8 @@ static void virt_machine_init(MachineState *machine)
         sifive_clint_create(
             memmap[VIRT_CLINT].base + i * memmap[VIRT_CLINT].size,
             memmap[VIRT_CLINT].size, base_hartid, hart_count,
-            SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE, true);
+            SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE,
+            SIFIVE_CLINT_TIMEBASE_FREQ, true);
 
         /* Per-socket PLIC hart topology configuration string */
         plic_hart_config_len =
target/riscv/cpu_helper.c +3 -1
index dc7ae3e..b0b91d4 100644
@@ -276,9 +276,11 @@ uint32_t riscv_cpu_update_mip(RISCVCPU *cpu, uint32_t mask, uint32_t value)
     return old;
 }
 
-void riscv_cpu_set_rdtime_fn(CPURISCVState *env, uint64_t (*fn)(void))
+void riscv_cpu_set_rdtime_fn(CPURISCVState *env, uint64_t (*fn)(uint32_t),
+                             uint32_t arg)
 {
     env->rdtime_fn = fn;
+    env->rdtime_fn_arg = arg;
 }
 
 void riscv_cpu_set_mode(CPURISCVState *env, target_ulong newpriv)
target/riscv/csr.c +2 -2
index 200001d..26ae347 100644
@@ -351,7 +351,7 @@ static int read_time(CPURISCVState *env, int csrno, target_ulong *val)
         return -RISCV_EXCP_ILLEGAL_INST;
     }
 
-    *val = env->rdtime_fn() + delta;
+    *val = env->rdtime_fn(env->rdtime_fn_arg) + delta;
     return 0;
 }
 
@@ -364,7 +364,7 @@ static int read_timeh(CPURISCVState *env, int csrno, target_ulong *val)
         return -RISCV_EXCP_ILLEGAL_INST;
     }
 
-    *val = (env->rdtime_fn() + delta) >> 32;
+    *val = (env->rdtime_fn(env->rdtime_fn_arg) + delta) >> 32;
     return 0;
 }
 #endif
Signature · 1 line
2.7.4
author
#16 lore raw

PATCH v2 16/16 hw/riscv: sifive_u: Connect a DMA controller

In reply to Bin Meng

From: Bin Meng <[email protected]>

SiFive FU540 SoC integrates a platform DMA controller with 4 DMA channels. This connects the exsiting SiFive PDMA model to the SoC, and adds its device tree data as well.

---

(no changes since v1)

 include/hw/riscv/sifive_u.h | 11 +++++++++++
 hw/riscv/sifive_u.c         | 30 ++++++++++++++++++++++++++++++
 hw/riscv/Kconfig            |  1 +
 3 files changed, 42 insertions(+)
include/hw/riscv/sifive_u.h +11 -0
index d3c0c00..793000a 100644
@@ -19,6 +19,7 @@
 #ifndef HW_SIFIVE_U_H
 #define HW_SIFIVE_U_H
 
+#include "hw/dma/sifive_pdma.h"
 #include "hw/net/cadence_gem.h"
 #include "hw/riscv/riscv_hart.h"
 #include "hw/riscv/sifive_cpu.h"
@@ -43,6 +44,7 @@ typedef struct SiFiveUSoCState {
     SiFiveUPRCIState prci;
     SIFIVEGPIOState gpio;
     SiFiveUOTPState otp;
+    SiFivePDMAState dma;
     CadenceGEMState gem;
 
     uint32_t serial;
@@ -72,6 +74,7 @@ enum {
     SIFIVE_U_MROM,
     SIFIVE_U_CLINT,
     SIFIVE_U_L2CC,
+    SIFIVE_U_PDMA,
     SIFIVE_U_L2LIM,
     SIFIVE_U_PLIC,
     SIFIVE_U_PRCI,
@@ -108,6 +111,14 @@ enum {
     SIFIVE_U_GPIO_IRQ13 = 20,
     SIFIVE_U_GPIO_IRQ14 = 21,
     SIFIVE_U_GPIO_IRQ15 = 22,
+    SIFIVE_U_PDMA_IRQ0 = 23,
+    SIFIVE_U_PDMA_IRQ1 = 24,
+    SIFIVE_U_PDMA_IRQ2 = 25,
+    SIFIVE_U_PDMA_IRQ3 = 26,
+    SIFIVE_U_PDMA_IRQ4 = 27,
+    SIFIVE_U_PDMA_IRQ5 = 28,
+    SIFIVE_U_PDMA_IRQ6 = 29,
+    SIFIVE_U_PDMA_IRQ7 = 30,
     SIFIVE_U_GEM_IRQ = 0x35
 };
 
hw/riscv/sifive_u.c +30 -0
index 2bc3992..7997537 100644
@@ -14,6 +14,7 @@
  * 4) GPIO (General Purpose Input/Output Controller)
  * 5) OTP (One-Time Programmable) memory with stored serial number
  * 6) GEM (Gigabit Ethernet Controller) and management block
+ * 7) DMA (Direct Memory Access Controller)
  *
  * This board currently generates devicetree dynamically that indicates at least
  * two harts and up to five harts.
@@ -73,6 +74,7 @@ static const struct MemmapEntry {
     [SIFIVE_U_MROM] =     {     0x1000,     0xf000 },
     [SIFIVE_U_CLINT] =    {  0x2000000,    0x10000 },
     [SIFIVE_U_L2CC] =     {  0x2010000,     0x1000 },
+    [SIFIVE_U_PDMA] =     {  0x3000000,   0x100000 },
     [SIFIVE_U_L2LIM] =    {  0x8000000,  0x2000000 },
     [SIFIVE_U_PLIC] =     {  0xc000000,  0x4000000 },
     [SIFIVE_U_PRCI] =     { 0x10000000,     0x1000 },
@@ -303,6 +305,22 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_string(fdt, nodename, "compatible", "gpio-restart");
     g_free(nodename);
 
+    nodename = g_strdup_printf("/soc/dma@%lx",
+        (long)memmap[SIFIVE_U_PDMA].base);
+    qemu_fdt_add_subnode(fdt, nodename);
+    qemu_fdt_setprop_cell(fdt, nodename, "#dma-cells", 1);
+    qemu_fdt_setprop_cells(fdt, nodename, "interrupts",
+        SIFIVE_U_PDMA_IRQ0, SIFIVE_U_PDMA_IRQ1, SIFIVE_U_PDMA_IRQ2,
+        SIFIVE_U_PDMA_IRQ3, SIFIVE_U_PDMA_IRQ4, SIFIVE_U_PDMA_IRQ5,
+        SIFIVE_U_PDMA_IRQ6, SIFIVE_U_PDMA_IRQ7);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cells(fdt, nodename, "reg",
+        0x0, memmap[SIFIVE_U_PDMA].base,
+        0x0, memmap[SIFIVE_U_PDMA].size);
+    qemu_fdt_setprop_string(fdt, nodename, "compatible",
+                            "sifive,fu540-c000-pdma");
+    g_free(nodename);
+
     nodename = g_strdup_printf("/soc/cache-controller@%lx",
         (long)memmap[SIFIVE_U_L2CC].base);
     qemu_fdt_add_subnode(fdt, nodename);
@@ -627,6 +645,7 @@ static void sifive_u_soc_instance_init(Object *obj)
     object_initialize_child(obj, "otp", &s->otp, TYPE_SIFIVE_U_OTP);
     object_initialize_child(obj, "gem", &s->gem, TYPE_CADENCE_GEM);
     object_initialize_child(obj, "gpio", &s->gpio, TYPE_SIFIVE_GPIO);
+    object_initialize_child(obj, "pdma", &s->dma, TYPE_SIFIVE_PDMA);
 }
 
 static void sifive_u_soc_realize(DeviceState *dev, Error **errp)
@@ -730,6 +749,17 @@ static void sifive_u_soc_realize(DeviceState *dev, Error **errp)
                                             SIFIVE_U_GPIO_IRQ0 + i));
     }
 
+    /* PDMA */
+    sysbus_realize(SYS_BUS_DEVICE(&s->dma), errp);
+    sysbus_mmio_map(SYS_BUS_DEVICE(&s->dma), 0, memmap[SIFIVE_U_PDMA].base);
+
+    /* Connect PDMA interrupts to the PLIC */
+    for (i = 0; i < SIFIVE_PDMA_IRQS; i++) {
+        sysbus_connect_irq(SYS_BUS_DEVICE(&s->dma), i,
+                           qdev_get_gpio_in(DEVICE(s->plic),
+                                            SIFIVE_U_PDMA_IRQ0 + i));
+    }
+
     qdev_prop_set_uint32(DEVICE(&s->otp), "serial", s->serial);
     if (!sysbus_realize(SYS_BUS_DEVICE(&s->otp), errp)) {
         return;
hw/riscv/Kconfig +1 -0
index 9032cb0..e53ab1e 100644
@@ -22,6 +22,7 @@ config SIFIVE_U
     select CADENCE
     select HART
     select SIFIVE
+    select SIFIVE_PDMA
     select UNIMP
 
 config SPIKE
Signature · 1 line
2.7.4
#17 lore raw
In reply to Bin Meng

Hi Bin,

Quoted 33 lines · Bin Meng

From: Bin Meng <[email protected]>

This adds support for Microchip PolarFire SoC Icicle Kit board. The Icicle Kit board integrates a PolarFire SoC, with one SiFive's E51 plus four U54 cores and many on-chip peripherals and an FPGA.

For more details about Microchip PolarFire SoC, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga

The Icicle Kit board information can be found here:
https://www.microsemi.com/existing-parts/parts/152514

Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000. The RISC-V CPU and HART codes has been updated to set the core's reset vector based on a configurable property from machine codes.

The following perepherals are created as an unimplemented device:

- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
- GPIO

The following perepherals are emulated:
- SiFive CLINT
- SiFive PLIC
- PolarFire SoC Multi-Mode UART
- SiFive PDMA
- Cadence eMMC/SDHCI controller
- Cadence Gigabit Ethernet MAC

Quoted 3 lines

The BIOS image used by this machine is hss.bin, aka Hart Software Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services

Are there any version requirements, or additional qemu patches, that need to be taken into account. Should I expect to see output on stdio?

I tried to build hss 3faaaaf8ce0d, using
https://github.com/riscv/riscv-gnu-toolchain (7f1f4ab5b0e0), which ends up being a gcc 10.1. That caused me to raise
https://github.com/polarfire-soc/hart-software-services/issues/2.

Suppressing that warning gets me a hss.bin, but neither that, nor one I build with Debian's 8.3 riscv64-linux-gnu- produces any output when I apply this set on top of 39335fab59. (Even when I change the wait to nowait.)

/
Leif

Quoted 109 lines

To launch this machine:

$ qemu-system-riscv64 -M microchip-icicle-kit -smp 5 \
    -bios path/to/hss.bin -sd path/to/sdcard.img \
    -nic tap,ifname=tap,script=no,model=cadence_gem \
    -display none -serial stdio \
    -chardev socket,id=serial1,path=serial1.sock,server,wait \
    -serial chardev:serial1

The memory is set to 1 GiB by default to match the hardware. A sanity check on ram size is performed in the machine init routine to prompt user to increase the RAM size to > 1 GiB when less than 1 GiB ram is detected.

HSS output is on the first serial port (stdio) and U-Boot/Linux outputs on the 2nd serial port. OpenSBI outputs on a random serial port due to the lottery mechanism used during the multi-core boot.

Please check the QEMU WiKi page for the target specific information:
https://wiki.qemu.org/Documentation/Platforms/RISCV#Microchip_PolarFire_SoC_Icicle_Kit

Changes in v2:
- change to update hw/char/meson.build
- add impl.min_access_size and impl.max_access_size as part of MemoryRegionOps and remove the allignment check
- change to update hw/sd/meson.build
- change the name to "generic-sdhci" when calling object_initialize_child()
- add a container MR to simplify out-of-bounds access checks
- do not initialize TYPE_SYSBUS_SDHCI in the SoC instance_init(), instead move that to the cadence_sdhci model
- do not access generic-sdhci's state directly,
instead move that to the cadence_sdhci model
- change to update hw/dma/meson.build
- rename the file names to sifive_pdma.[c|h]
- update irq number to 8 per the SiFive FU540 manual
- fix the register offset for channel 1/2/3 in the read/write ops
- connect 8 IRQs to the PLIC
- change "phy-addr" default value to BOARD_PHY_ADDRESS

Bin Meng (16):
target/riscv: cpu: Add a new 'resetvec' property
hw/riscv: hart: Add a new 'resetvec' property target/riscv: cpu: Set reset vector based on the configured property
value
hw/riscv: Initial support for Microchip PolarFire SoC Icicle Kit board hw/char: Add Microchip PolarFire SoC MMUART emulation hw/riscv: microchip_pfsoc: Connect 5 MMUARTs
hw/sd: Add Cadence SDHCI emulation
hw/riscv: microchip_pfsoc: Connect a Cadence SDHCI controller and an
SD card
hw/dma: Add SiFive platform DMA controller emulation hw/riscv: microchip_pfsoc: Connect a DMA controller hw/net: cadence_gem: Add a new 'phy-addr' property
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23 hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: clint: Avoid using hard-coded timebase frequency hw/riscv: sifive_u: Connect a DMA controller

 default-configs/riscv64-softmmu.mak |   1 +
 include/hw/char/mchp_pfsoc_mmuart.h |  61 +++++
 include/hw/dma/sifive_pdma.h        |  57 +++++
 include/hw/net/cadence_gem.h        |   2 +
 include/hw/riscv/microchip_pfsoc.h  | 133 +++++++++++
 include/hw/riscv/riscv_hart.h       |   1 +
 include/hw/riscv/sifive_clint.h     |   4 +-
 include/hw/riscv/sifive_u.h         |  11 +
 include/hw/sd/cadence_sdhci.h       |  47 ++++
 target/riscv/cpu.h                  |   7 +-
 hw/arm/xilinx_zynq.c                |   1 +
 hw/arm/xlnx-versal.c                |   1 +
 hw/arm/xlnx-zynqmp.c                |   1 +
 hw/char/mchp_pfsoc_mmuart.c         |  86 +++++++
 hw/dma/sifive_pdma.c                | 313 ++++++++++++++++++++++++++
 hw/net/cadence_gem.c                |   7 +-
 hw/riscv/microchip_pfsoc.c          | 437 ++++++++++++++++++++++++++++++++++++
 hw/riscv/opentitan.c                |   1 +
 hw/riscv/riscv_hart.c               |   3 +
 hw/riscv/sifive_clint.c             |  26 ++-
 hw/riscv/sifive_e.c                 |   4 +-
 hw/riscv/sifive_u.c                 |  35 ++-
 hw/riscv/spike.c                    |   3 +-
 hw/riscv/virt.c                     |   3 +-
 hw/sd/cadence_sdhci.c               | 193 ++++++++++++++++
 target/riscv/cpu.c                  |   8 +-
 target/riscv/cpu_helper.c           |   4 +-
 target/riscv/csr.c                  |   4 +-
 MAINTAINERS                         |   9 +
 hw/char/Kconfig                     |   3 +
 hw/char/meson.build                 |   1 +
 hw/dma/Kconfig                      |   3 +
 hw/dma/meson.build                  |   1 +
 hw/riscv/Kconfig                    |  10 +
 hw/riscv/meson.build                |   1 +
 hw/sd/Kconfig                       |   4 +
 hw/sd/meson.build                   |   1 +
 37 files changed, 1458 insertions(+), 29 deletions(-)
 create mode 100644 include/hw/char/mchp_pfsoc_mmuart.h
 create mode 100644 include/hw/dma/sifive_pdma.h
 create mode 100644 include/hw/riscv/microchip_pfsoc.h
 create mode 100644 include/hw/sd/cadence_sdhci.h
 create mode 100644 hw/char/mchp_pfsoc_mmuart.c
 create mode 100644 hw/dma/sifive_pdma.c
 create mode 100644 hw/riscv/microchip_pfsoc.c
 create mode 100644 hw/sd/cadence_sdhci.c
Signature · 1 line
2.7.4
author
#18 lore raw

Hi Leif,

Quoted 37 lines · Leif Lindholm

Hi Bin,

Quoted 33 lines · Bin Meng

From: Bin Meng <[email protected]>

This adds support for Microchip PolarFire SoC Icicle Kit board. The Icicle Kit board integrates a PolarFire SoC, with one SiFive's E51 plus four U54 cores and many on-chip peripherals and an FPGA.

For more details about Microchip PolarFire SoC, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga

The Icicle Kit board information can be found here:
https://www.microsemi.com/existing-parts/parts/152514

Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000. The RISC-V CPU and HART codes has been updated to set the core's reset vector based on a configurable property from machine codes.

The following perepherals are created as an unimplemented device:

- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
- GPIO

The following perepherals are emulated:
- SiFive CLINT
- SiFive PLIC
- PolarFire SoC Multi-Mode UART
- SiFive PDMA
- Cadence eMMC/SDHCI controller
- Cadence Gigabit Ethernet MAC

Quoted 6 lines
Quoted 3 lines

The BIOS image used by this machine is hss.bin, aka Hart Software Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services

Are there any version requirements, or additional qemu patches, that need to be taken into account. Should I expect to see output on stdio?

Thanks for trying!

Did you apply the patch to skip the DDR memory initialization mentioned in this page?
https://wiki.qemu.org/Documentation/Platforms/RISCV#Microchip_PolarFire_SoC_Icicle_Kit

Quoted 5 lines

I tried to build hss 3faaaaf8ce0d, using
https://github.com/riscv/riscv-gnu-toolchain (7f1f4ab5b0e0), which ends up being a gcc 10.1. That caused me to raise
https://github.com/polarfire-soc/hart-software-services/issues/2.

Yes, GCC 10 does not build is a known issue. Currently I am using GCC 9 to build HSS.

Quoted 6 lines

Suppressing that warning gets me a hss.bin, but neither that, nor one I build with Debian's 8.3 riscv64-linux-gnu- produces any output when I apply this set on top of 39335fab59. (Even when I change the wait to nowait.)

Regards,
Bin

#19 lore raw
Quoted 14 lines · Bin Meng

Hi Leif,

Quoted 12 lines
Quoted 11 lines

The following perepherals are emulated:
- SiFive CLINT
- SiFive PLIC
- PolarFire SoC Multi-Mode UART
- SiFive PDMA
- Cadence eMMC/SDHCI controller
- Cadence Gigabit Ethernet MAC

The BIOS image used by this machine is hss.bin, aka Hart Software Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services

Quoted 8 lines
Quoted 2 lines

Are there any version requirements, or additional qemu patches, that need to be taken into account. Should I expect to see output on stdio?

Thanks for trying!

Did you apply the patch to skip the DDR memory initialization mentioned in this page?
https://wiki.qemu.org/Documentation/Platforms/RISCV#Microchip_PolarFire_SoC_Icicle_Kit

I did, but in honesty only after I sent the previous email :) (Since it made no difference, I didn't bother following up.)

Quoted 7 lines
Quoted 4 lines

I tried to build hss 3faaaaf8ce0d, using
https://github.com/riscv/riscv-gnu-toolchain (7f1f4ab5b0e0), which ends up being a gcc 10.1. That caused me to raise
https://github.com/polarfire-soc/hart-software-services/issues/2.

Yes, GCC 10 does not build is a known issue. Currently I am using GCC 9 to build HSS.

Right, I can confirm that with commit 93f82dc18e1d riscv-gnu-toolchain (the last before changing to gcc 10.1), I generate a 9.2.0 gcc that builds a hss.bin that boots successfully with the minimal command line

qemu-system-riscv64 -M microchip-icicle-kit -smp 5 -bios hss.bin \
-display none -serial stdio

Thanks!

(I haven't looked any further than the hss.bin yet, but I'm now unblocked to do so.)

Best Regards,

Leif