Skip to contentSkip to conversation

MT8192 IOMMU support

PATCH Superseded Yong Wu 2 participants 30 messages Sep 5, 2020 – Sep 18, 2020

Subsystems (7)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore

Yong Wu

author maintainer
#0 lore raw

v2 cover MT8192 IOMMU support

This patch mainly adds support for mt8192 IOMMU and SMI.

mt8192 also is MTK IOMMU gen2 which uses ARM Short-Descriptor translation table format. The M4U-SMI HW diagram is as below:

                          EMI
                           |
                          M4U
                           |
                      ------------
                       SMI Common
                      ------------
                           |
  +-------+------+------+----------------------+-------+
  |       |      |      |       ......         |       |
  |       |      |      |                      |       |
larb0   larb1  larb2  larb4     ......      larb19   larb20
disp0   disp1   mdp    vdec                   IPE      IPE

All the connections are HW fixed, SW can NOT adjust it.

Comparing with the preview SoC, this patchset mainly adds two new functions:
a) add iova 34 bits support.
b) add multi domains support since several HW has the special iova region requirement.

this patchset depend on v5.9-rc1.

change note:
v2:
a) Convert IOMMU/SMI dt-binding to DT schema.
b) Fix some comment from Pi-Hsun and Nicolas. like use generic_iommu_put_resv_regions.
c) Reword some comment, like add how to use domain-id.

v1: https://lore.kernel.org/linux-iommu/[email protected]/

Yong Wu (23):
dt-bindings: iommu: mediatek: Convert IOMMU to DT schema
dt-bindings: memory: mediatek: Convert SMI to DT schema
dt-bindings: memory: mediatek: Add a common larb-port header file
dt-bindings: memory: mediatek: Extend LARB_NR_MAX to 32
dt-bindings: memory: mediatek: Add domain definition
dt-bindings: mediatek: Add binding for mt8192 IOMMU and SMI iommu/mediatek: Use the common mtk-smi-larb-port.h iommu/io-pgtable-arm-v7s: Use ias to check the valid iova in unmap iommu/io-pgtable-arm-v7s: Extend PA34 for MediaTek iommu/io-pgtable-arm-v7s: Add cfg as a param in some macros iommu/io-pgtable-arm-v7s: Quad lvl1 pgtable for MediaTek iommu/mediatek: Move hw_init into attach_device iommu/mediatek: Add device link for smi-common and m4u iommu/mediatek: Add power-domain operation iommu/mediatek: Add iova reserved function iommu/mediatek: Add single domain
iommu/mediatek: Support master use iova over 32bit iommu/mediatek: Support up to 34bit iova in tlb flush iommu/mediatek: Support report iova 34bit translation fault in ISR iommu/mediatek: Add support for multi domain iommu/mediatek: Adjust the structure
iommu/mediatek: Add mt8192 support
memory: mtk-smi: Add mt8192 support

 .../bindings/iommu/mediatek,iommu.txt         | 103 --------
 .../bindings/iommu/mediatek,iommu.yaml        | 155 +++++++++++
 .../mediatek,smi-common.txt                   |  49 ----
 .../mediatek,smi-common.yaml                  |  97 +++++++
 .../memory-controllers/mediatek,smi-larb.txt  |  49 ----
 .../memory-controllers/mediatek,smi-larb.yaml |  86 ++++++
 drivers/iommu/io-pgtable-arm-v7s.c            |  57 ++--
 drivers/iommu/mtk_iommu.c                     | 247 ++++++++++++++----
 drivers/iommu/mtk_iommu.h                     |  11 +-
 drivers/memory/mtk-smi.c                      |  27 ++
 include/dt-bindings/memory/mt2712-larb-port.h |   2 +-
 include/dt-bindings/memory/mt6779-larb-port.h |   2 +-
 include/dt-bindings/memory/mt8173-larb-port.h |   2 +-
 include/dt-bindings/memory/mt8183-larb-port.h |   2 +-
 include/dt-bindings/memory/mt8192-larb-port.h | 239 +++++++++++++++++
 .../dt-bindings/memory/mtk-smi-larb-port.h    |  22 ++
 include/linux/io-pgtable.h                    |   4 +-
 include/soc/mediatek/smi.h                    |   3 +-
 18 files changed, 880 insertions(+), 277 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
 create mode 100644 Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
 create mode 100644 include/dt-bindings/memory/mt8192-larb-port.h
 create mode 100644 include/dt-bindings/memory/mtk-smi-larb-port.h
Signature · 1 line
2.18.0
author maintainer
#1 lore raw

PATCH v2 1/23 dt-bindings: iommu: mediatek: Convert IOMMU to DT schema

Convert MediaTek IOMMU to DT schema.

---
 .../bindings/iommu/mediatek,iommu.txt         | 103 ------------
 .../bindings/iommu/mediatek,iommu.yaml        | 150 ++++++++++++++++++
 2 files changed, 150 insertions(+), 103 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
 create mode 100644 Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml
Documentation/devicetree/bindings/iommu/mediatek,iommu.txt deleted +0 -103
deleted file mode 100644
index c1ccd8582eb2..000000000000
@@ -1,103 +0,0 @@
-* Mediatek IOMMU Architecture Implementation
-
-  Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and
-this M4U have two generations of HW architecture. Generation one uses flat
-pagetable, and only supports 4K size page mapping. Generation two uses the
-ARM Short-Descriptor translation table format for address translation.
-
-  About the M4U Hardware Block Diagram, please check below:
-
-              EMI (External Memory Interface)
-               |
-              m4u (Multimedia Memory Management Unit)
-               |
-          +--------+
-          |        |
-      gals0-rx   gals1-rx    (Global Async Local Sync rx)
-          |        |
-          |        |
-      gals0-tx   gals1-tx    (Global Async Local Sync tx)
-          |        |          Some SoCs may have GALS.
-          +--------+
-               |
-           SMI Common(Smart Multimedia Interface Common)
-               |
-       +----------------+-------
-       |                |
-       |             gals-rx        There may be GALS in some larbs.
-       |                |
-       |                |
-       |             gals-tx
-       |                |
-   SMI larb0        SMI larb1   ... SoCs have several SMI local arbiter(larb).
-   (display)         (vdec)
-       |                |
-       |                |
- +-----+-----+     +----+----+
- |     |     |     |    |    |
- |     |     |...  |    |    |  ... There are different ports in each larb.
- |     |     |     |    |    |
-OVL0 RDMA0 WDMA0  MC   PP   VLD
-
-  As above, The Multimedia HW will go through SMI and M4U while it
-access EMI. SMI is a bridge between m4u and the Multimedia HW. It contain
-smi local arbiter and smi common. It will control whether the Multimedia
-HW should go though the m4u for translation or bypass it and talk
-directly with EMI. And also SMI help control the power domain and clocks for
-each local arbiter.
-  Normally we specify a local arbiter(larb) for each multimedia HW
-like display, video decode, and camera. And there are different ports
-in each larb. Take a example, There are many ports like MC, PP, VLD in the
-video decode local arbiter, all these ports are according to the video HW.
-  In some SoCs, there may be a GALS(Global Async Local Sync) module between
-smi-common and m4u, and additional GALS module between smi-larb and
-smi-common. GALS can been seen as a "asynchronous fifo" which could help
-synchronize for the modules in different clock frequency.
-
-Required properties:
-- compatible : must be one of the following string:
-	"mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
-	"mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW.
-	"mediatek,mt6779-m4u" for mt6779 which uses generation two m4u HW.
-	"mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses
-						     generation one m4u HW.
-	"mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
-	"mediatek,mt8183-m4u" for mt8183 which uses generation two m4u HW.
-- reg : m4u register base and size.
-- interrupts : the interrupt of m4u.
-- clocks : must contain one entry for each clock-names.
-- clock-names : Only 1 optional clock:
-  - "bclk": the block clock of m4u.
-  Here is the list which require this "bclk":
-  - mt2701, mt2712, mt7623 and mt8173.
-  Note that m4u use the EMI clock which always has been enabled before kernel
-  if there is no this "bclk".
-- mediatek,larbs : List of phandle to the local arbiters in the current Socs.
-	Refer to bindings/memory-controllers/mediatek,smi-larb.txt. It must sort
-	according to the local arbiter index, like larb0, larb1, larb2...
-- iommu-cells : must be 1. This is the mtk_m4u_id according to the HW.
-	Specifies the mtk_m4u_id as defined in
-	dt-binding/memory/mt2701-larb-port.h for mt2701, mt7623
-	dt-binding/memory/mt2712-larb-port.h for mt2712,
-	dt-binding/memory/mt6779-larb-port.h for mt6779,
-	dt-binding/memory/mt8173-larb-port.h for mt8173, and
-	dt-binding/memory/mt8183-larb-port.h for mt8183.
-
-Example:
-	iommu: iommu@10205000 {
-		compatible = "mediatek,mt8173-m4u";
-		reg = <0 0x10205000 0 0x1000>;
-		interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&infracfg CLK_INFRA_M4U>;
-		clock-names = "bclk";
-		mediatek,larbs = <&larb0 &larb1 &larb2 &larb3 &larb4 &larb5>;
-		#iommu-cells = <1>;
-	};
-
-Example for a client device:
-	display {
-		compatible = "mediatek,mt8173-disp";
-		iommus = <&iommu M4U_PORT_DISP_OVL0>,
-			 <&iommu M4U_PORT_DISP_RDMA0>;
-		...
-	};
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +150 -0

150 lines not on this page · raw message

Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
maintainer
#2 lore raw

Re: [PATCH v2 01/23] dt-bindings: iommu: mediatek: Convert IOMMU to DT schema

Quoted 191 lines · Yong Wu

Convert MediaTek IOMMU to DT schema.

---
 .../bindings/iommu/mediatek,iommu.txt         | 103 ------------
 .../bindings/iommu/mediatek,iommu.yaml        | 150 ++++++++++++++++++
 2 files changed, 150 insertions(+), 103 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
 create mode 100644 Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml
Documentation/devicetree/bindings/iommu/mediatek,iommu.txt deleted +0 -103
deleted file mode 100644
index c1ccd8582eb2..000000000000
@@ -1,103 +0,0 @@
-* Mediatek IOMMU Architecture Implementation
-
-  Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and
-this M4U have two generations of HW architecture. Generation one uses flat
-pagetable, and only supports 4K size page mapping. Generation two uses the
-ARM Short-Descriptor translation table format for address translation.
-
-  About the M4U Hardware Block Diagram, please check below:
-
-              EMI (External Memory Interface)
-               |
-              m4u (Multimedia Memory Management Unit)
-               |
-          +--------+
-          |        |
-      gals0-rx   gals1-rx    (Global Async Local Sync rx)
-          |        |
-          |        |
-      gals0-tx   gals1-tx    (Global Async Local Sync tx)
-          |        |          Some SoCs may have GALS.
-          +--------+
-               |
-           SMI Common(Smart Multimedia Interface Common)
-               |
-       +----------------+-------
-       |                |
-       |             gals-rx        There may be GALS in some larbs.
-       |                |
-       |                |
-       |             gals-tx
-       |                |
-   SMI larb0        SMI larb1   ... SoCs have several SMI local arbiter(larb).
-   (display)         (vdec)
-       |                |
-       |                |
- +-----+-----+     +----+----+
- |     |     |     |    |    |
- |     |     |...  |    |    |  ... There are different ports in each larb.
- |     |     |     |    |    |
-OVL0 RDMA0 WDMA0  MC   PP   VLD
-
-  As above, The Multimedia HW will go through SMI and M4U while it
-access EMI. SMI is a bridge between m4u and the Multimedia HW. It contain
-smi local arbiter and smi common. It will control whether the Multimedia
-HW should go though the m4u for translation or bypass it and talk
-directly with EMI. And also SMI help control the power domain and clocks for
-each local arbiter.
-  Normally we specify a local arbiter(larb) for each multimedia HW
-like display, video decode, and camera. And there are different ports
-in each larb. Take a example, There are many ports like MC, PP, VLD in the
-video decode local arbiter, all these ports are according to the video HW.
-  In some SoCs, there may be a GALS(Global Async Local Sync) module between
-smi-common and m4u, and additional GALS module between smi-larb and
-smi-common. GALS can been seen as a "asynchronous fifo" which could help
-synchronize for the modules in different clock frequency.
-
-Required properties:
-- compatible : must be one of the following string:
-	"mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
-	"mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW.
-	"mediatek,mt6779-m4u" for mt6779 which uses generation two m4u HW.
-	"mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses
-						     generation one m4u HW.
-	"mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
-	"mediatek,mt8183-m4u" for mt8183 which uses generation two m4u HW.
-- reg : m4u register base and size.
-- interrupts : the interrupt of m4u.
-- clocks : must contain one entry for each clock-names.
-- clock-names : Only 1 optional clock:
-  - "bclk": the block clock of m4u.
-  Here is the list which require this "bclk":
-  - mt2701, mt2712, mt7623 and mt8173.
-  Note that m4u use the EMI clock which always has been enabled before kernel
-  if there is no this "bclk".
-- mediatek,larbs : List of phandle to the local arbiters in the current Socs.
-	Refer to bindings/memory-controllers/mediatek,smi-larb.txt. It must sort
-	according to the local arbiter index, like larb0, larb1, larb2...
-- iommu-cells : must be 1. This is the mtk_m4u_id according to the HW.
-	Specifies the mtk_m4u_id as defined in
-	dt-binding/memory/mt2701-larb-port.h for mt2701, mt7623
-	dt-binding/memory/mt2712-larb-port.h for mt2712,
-	dt-binding/memory/mt6779-larb-port.h for mt6779,
-	dt-binding/memory/mt8173-larb-port.h for mt8173, and
-	dt-binding/memory/mt8183-larb-port.h for mt8183.
-
-Example:
-	iommu: iommu@10205000 {
-		compatible = "mediatek,mt8173-m4u";
-		reg = <0 0x10205000 0 0x1000>;
-		interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&infracfg CLK_INFRA_M4U>;
-		clock-names = "bclk";
-		mediatek,larbs = <&larb0 &larb1 &larb2 &larb3 &larb4 &larb5>;
-		#iommu-cells = <1>;
-	};
-
-Example for a client device:
-	display {
-		compatible = "mediatek,mt8173-disp";
-		iommus = <&iommu M4U_PORT_DISP_OVL0>,
-			 <&iommu M4U_PORT_DISP_RDMA0>;
-		...
-	};
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +66 -0
new file mode 100644
index 000000000000..d7b31bda3e35
@@ -0,0 +1,150 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iommu/mediatek,iommu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek IOMMU Architecture Implementation
+
+maintainers:
+  - Yong Wu <[email protected]>
+  - Chao Hao <[email protected]>
+
+description: |+
+  Some MediaTek SOCs contain a Multimedia Memory Management Unit (M4U), and
+  this M4U have two generations of HW architecture. Generation one uses flat
+  pagetable, and only supports 4K size page mapping. Generation two uses the
+  ARM Short-Descriptor translation table format for address translation.
+
+  About the M4U Hardware Block Diagram, please check below:
+
+                EMI (External Memory Interface)
+                 |
+                m4u (Multimedia Memory Management Unit)
+                 |
+            +--------+
+            |        |
+        gals0-rx   gals1-rx    (Global Async Local Sync rx)
+            |        |
+            |        |
+        gals0-tx   gals1-tx    (Global Async Local Sync tx)
+            |        |          Some SoCs may have GALS.
+            +--------+
+                 |
+             SMI Common(Smart Multimedia Interface Common)
+                 |
+         +----------------+-------
+         |                |
+         |             gals-rx        There may be GALS in some larbs.
+         |                |
+         |                |
+         |             gals-tx
+         |                |
+     SMI larb0        SMI larb1   ... SoCs have several SMI local arbiter(larb).
+     (display)         (vdec)
+         |                |
+         |                |
+   +-----+-----+     +----+----+
+   |     |     |     |    |    |
+   |     |     |...  |    |    |  ... There are different ports in each larb.
+   |     |     |     |    |    |
+  OVL0 RDMA0 WDMA0  MC   PP   VLD
+
+  As above, The Multimedia HW will go through SMI and M4U while it
+  access EMI. SMI is a bridge between m4u and the Multimedia HW. It contain
+  smi local arbiter and smi common. It will control whether the Multimedia
+  HW should go though the m4u for translation or bypass it and talk
+  directly with EMI. And also SMI help control the power domain and clocks for
+  each local arbiter.
+
+  Normally we specify a local arbiter(larb) for each multimedia HW
+  like display, video decode, and camera. And there are different ports
+  in each larb. Take a example, There are many ports like MC, PP, VLD in the
+  video decode local arbiter, all these ports are according to the video HW.
+
+  In some SoCs, there may be a GALS(Global Async Local Sync) module between
+  smi-common and m4u, and additional GALS module between smi-larb and

Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml line 76

Quoted 10 lines
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +10 -0
+  smi-common. GALS can been seen as a "asynchronous fifo" which could help
+  synchronize for the modules in different clock frequency.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-m4u #mt2701 generation one HW
+      - mediatek,mt2712-m4u #mt2712 generation two HW
+      - mediatek,mt6779-m4u #mt6779 generation two HW
+      - mediatek,mt7623-m4u, mediatek,mt2701-m4u #mt7623 generation one HW

This is not right.

items:
- const: mediatek,mt7623-m4u
- const: mediatek,mt2701-m4u

And that has to be under a 'oneOf' with the rest of this.

Quoted 76 lines
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +74 -0
+      - mediatek,mt8173-m4u #mt8173 generation two HW
+      - mediatek,mt8183-m4u #mt8183 generation two HW
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: |
+      bclk is optional. here is the list which require this bclk:
+      mt2701, mt2712, mt7623 and mt8173.
+      M4U will use the EMI clock which always has been enabled before
+      kernel if there is no this bclk.
+    items:
+      - description: bclk is the block clock.
+
+  clock-names:
+    items:
+      - const: bclk
+
+  mediatek,larbs:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: |
+      List of phandle to the local arbiters in the current Socs.
+      Refer to bindings/memory-controllers/mediatek,smi-larb.yaml. It must sort
+      according to the local arbiter index, like larb0, larb1, larb2...
+
+  '#iommu-cells':
+    const: 1
+    description: |
+      This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as
+      defined in
+      dt-binding/memory/mt2701-larb-port.h for mt2701 and mt7623,
+      dt-binding/memory/mt2712-larb-port.h for mt2712,
+      dt-binding/memory/mt6779-larb-port.h for mt6779,
+      dt-binding/memory/mt8173-larb-port.h for mt8173,
+      dt-binding/memory/mt8183-larb-port.h for mt8183.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - mediatek,larbs
+  - '#iommu-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    iommu: iommu@10205000 {
+            compatible = "mediatek,mt8173-m4u";
+            reg = <0x10205000 0x1000>;
+            interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&infracfg CLK_INFRA_M4U>;
+            clock-names = "bclk";
+            mediatek,larbs = <&larb0 &larb1 &larb2
+                              &larb3 &larb4 &larb5>;
+            #iommu-cells = <1>;
+    };
+
+  - |
+    #include <dt-bindings/memory/mt8173-larb-port.h>
+
+    /* Example for a client device */
+    display {
+           compatible = "mediatek,mt8173-disp";
+           iommus = <&iommu M4U_PORT_DISP_OVL0>,
+                    <&iommu M4U_PORT_DISP_RDMA0>;
+     };
Signature · 1 line
2.18.0
author maintainer
#3 lore raw

Re: [PATCH v2 01/23] dt-bindings: iommu: mediatek: Convert IOMMU to DT schema

Quoted 5 lines · Rob Herring
Quoted 4 lines · Yong Wu

Convert MediaTek IOMMU to DT schema.

---

[...]

Quoted 8 lines

Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml line 76

Quoted 7 lines
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +7 -0
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-m4u #mt2701 generation one HW
+      - mediatek,mt2712-m4u #mt2712 generation two HW
+      - mediatek,mt6779-m4u #mt6779 generation two HW
+      - mediatek,mt7623-m4u, mediatek,mt2701-m4u #mt7623 generation one HW
Quoted 7 lines

This is not right.

items:
- const: mediatek,mt7623-m4u
- const: mediatek,mt2701-m4u

And that has to be under a 'oneOf' with the rest of this.

Thanks for the review. Is this OK?

compatible:
oneOf:
- const: mediatek,mt2701-m4u # mt2701 generation one HW
- const: mediatek,mt2712-m4u # mt2712 generation two HW
- const: mediatek,mt6779-m4u # mt6779 generation two HW
- const: mediatek,mt8173-m4u # mt8173 generation two HW
- const: mediatek,mt8183-m4u # mt8183 generation two HW
- const: mediatek,mt8192-m4u # mt8192 generation two HW

- description: mt7623 generation one HW
items:
- const: mediatek,mt7623-m4u
- const: mediatek,mt2701-m4u

Quoted 6 lines
Quoted 6 lines
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +5 -0
+      - mediatek,mt8173-m4u #mt8173 generation two HW
+      - mediatek,mt8183-m4u #mt8183 generation two HW
+
+  reg:
+    maxItems: 1

[snip]

maintainer
#4 lore raw

Re: [PATCH v2 01/23] dt-bindings: iommu: mediatek: Convert IOMMU to DT schema

Quoted 28 lines · Yong Wu
Quoted 5 lines · Rob Herring
Quoted 4 lines · Yong Wu

Convert MediaTek IOMMU to DT schema.

---

[...]

Quoted 8 lines

Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml line 76

Quoted 7 lines
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +7 -0
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-m4u #mt2701 generation one HW
+      - mediatek,mt2712-m4u #mt2712 generation two HW
+      - mediatek,mt6779-m4u #mt6779 generation two HW
+      - mediatek,mt7623-m4u, mediatek,mt2701-m4u #mt7623 generation one HW
Quoted 7 lines

This is not right.

items:
- const: mediatek,mt7623-m4u
- const: mediatek,mt2701-m4u

And that has to be under a 'oneOf' with the rest of this.

Thanks for the review. Is this OK?

Quoted 8 lines

compatible:
oneOf:
- const: mediatek,mt2701-m4u # mt2701 generation one HW
- const: mediatek,mt2712-m4u # mt2712 generation two HW
- const: mediatek,mt6779-m4u # mt6779 generation two HW
- const: mediatek,mt8173-m4u # mt8173 generation two HW
- const: mediatek,mt8183-m4u # mt8183 generation two HW
- const: mediatek,mt8192-m4u # mt8192 generation two HW

It is correct, but I prefer all these to be a single enum. So 'oneOf' would have 2 entries.

Quoted 13 lines

- description: mt7623 generation one HW
items:
- const: mediatek,mt7623-m4u
- const: mediatek,mt2701-m4u

Quoted 6 lines
Quoted 6 lines
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml new file +5 -0
+      - mediatek,mt8173-m4u #mt8173 generation two HW
+      - mediatek,mt8183-m4u #mt8183 generation two HW
+
+  reg:
+    maxItems: 1

[snip]

author maintainer
#5 lore raw

PATCH v2 2/23 dt-bindings: memory: mediatek: Convert SMI to DT schema

In reply to Yong Wu

Convert MediaTek SMI to DT schema.

---
 .../mediatek,smi-common.txt                   | 49 ----------
 .../mediatek,smi-common.yaml                  | 96 +++++++++++++++++++
 .../memory-controllers/mediatek,smi-larb.txt  | 49 ----------
 .../memory-controllers/mediatek,smi-larb.yaml | 85 ++++++++++++++++
 4 files changed, 181 insertions(+), 98 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt deleted +0 -49
deleted file mode 100644
index b64573680b42..000000000000
@@ -1,49 +0,0 @@
-SMI (Smart Multimedia Interface) Common
-
-The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
-
-Mediatek SMI have two generations of HW architecture, here is the list
-which generation the SoCs use:
-generation 1: mt2701 and mt7623.
-generation 2: mt2712, mt6779, mt8173 and mt8183.
-
-There's slight differences between the two SMI, for generation 2, the
-register which control the iommu port is at each larb's register base. But
-for generation 1, the register is at smi ao base(smi always on register
-base). Besides that, the smi async clock should be prepared and enabled for
-SMI generation 1 to transform the smi clock into emi clock domain, but that is
-not needed for SMI generation 2.
-
-Required properties:
-- compatible : must be one of :
-	"mediatek,mt2701-smi-common"
-	"mediatek,mt2712-smi-common"
-	"mediatek,mt6779-smi-common"
-	"mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common"
-	"mediatek,mt8173-smi-common"
-	"mediatek,mt8183-smi-common"
-- reg : the register and size of the SMI block.
-- power-domains : a phandle to the power domain of this local arbiter.
-- clocks : Must contain an entry for each entry in clock-names.
-- clock-names : must contain 3 entries for generation 1 smi HW and 2 entries
-  for generation 2 smi HW as follows:
-  - "apb" : Advanced Peripheral Bus clock, It's the clock for setting
-	    the register.
-  - "smi" : It's the clock for transfer data and command.
-	    They may be the same if both source clocks are the same.
-  - "async" : asynchronous clock, it help transform the smi clock into the emi
-	      clock domain, this clock is only needed by generation 1 smi HW.
-  and these 2 option clocks for generation 2 smi HW:
-  - "gals0": the path0 clock of GALS(Global Async Local Sync).
-  - "gals1": the path1 clock of GALS(Global Async Local Sync).
-  Here is the list which has this GALS: mt6779 and mt8183.
-
-Example:
-	smi_common: smi@14022000 {
-		compatible = "mediatek,mt8173-smi-common";
-		reg = <0 0x14022000 0 0x1000>;
-		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
-		clocks = <&mmsys CLK_MM_SMI_COMMON>,
-			 <&mmsys CLK_MM_SMI_COMMON>;
-		clock-names = "apb", "smi";
-	};
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml new file +96 -0

96 lines not on this page · raw message

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt deleted +0 -49

49 lines not on this page · raw message

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +85 -0

85 lines not on this page · raw message

Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
maintainer
#6 lore raw

Re: [PATCH v2 02/23] dt-bindings: memory: mediatek: Convert SMI to DT schema

Quoted 98 lines · Yong Wu

Convert MediaTek SMI to DT schema.

---
 .../mediatek,smi-common.txt                   | 49 ----------
 .../mediatek,smi-common.yaml                  | 96 +++++++++++++++++++
 .../memory-controllers/mediatek,smi-larb.txt  | 49 ----------
 .../memory-controllers/mediatek,smi-larb.yaml | 85 ++++++++++++++++
 4 files changed, 181 insertions(+), 98 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt deleted +0 -49
deleted file mode 100644
index b64573680b42..000000000000
@@ -1,49 +0,0 @@
-SMI (Smart Multimedia Interface) Common
-
-The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
-
-Mediatek SMI have two generations of HW architecture, here is the list
-which generation the SoCs use:
-generation 1: mt2701 and mt7623.
-generation 2: mt2712, mt6779, mt8173 and mt8183.
-
-There's slight differences between the two SMI, for generation 2, the
-register which control the iommu port is at each larb's register base. But
-for generation 1, the register is at smi ao base(smi always on register
-base). Besides that, the smi async clock should be prepared and enabled for
-SMI generation 1 to transform the smi clock into emi clock domain, but that is
-not needed for SMI generation 2.
-
-Required properties:
-- compatible : must be one of :
-	"mediatek,mt2701-smi-common"
-	"mediatek,mt2712-smi-common"
-	"mediatek,mt6779-smi-common"
-	"mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common"
-	"mediatek,mt8173-smi-common"
-	"mediatek,mt8183-smi-common"
-- reg : the register and size of the SMI block.
-- power-domains : a phandle to the power domain of this local arbiter.
-- clocks : Must contain an entry for each entry in clock-names.
-- clock-names : must contain 3 entries for generation 1 smi HW and 2 entries
-  for generation 2 smi HW as follows:
-  - "apb" : Advanced Peripheral Bus clock, It's the clock for setting
-	    the register.
-  - "smi" : It's the clock for transfer data and command.
-	    They may be the same if both source clocks are the same.
-  - "async" : asynchronous clock, it help transform the smi clock into the emi
-	      clock domain, this clock is only needed by generation 1 smi HW.
-  and these 2 option clocks for generation 2 smi HW:
-  - "gals0": the path0 clock of GALS(Global Async Local Sync).
-  - "gals1": the path1 clock of GALS(Global Async Local Sync).
-  Here is the list which has this GALS: mt6779 and mt8183.
-
-Example:
-	smi_common: smi@14022000 {
-		compatible = "mediatek,mt8173-smi-common";
-		reg = <0 0x14022000 0 0x1000>;
-		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
-		clocks = <&mmsys CLK_MM_SMI_COMMON>,
-			 <&mmsys CLK_MM_SMI_COMMON>;
-		clock-names = "apb", "smi";
-	};
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml new file +23 -0
new file mode 100644
index 000000000000..781d7b7617d9
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/mediatek,smi-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SMI (Smart Multimedia Interface) Common
+
+maintainers:
+  - Yong Wu <[email protected]>
+
+description: |+
+  The hardware block diagram please check bindings/iommu/mediatek,iommu.yaml
+
+  MediaTek SMI have two generations of HW architecture, here is the list
+  which generation the SoCs use:
+  generation 1: mt2701 and mt7623.
+  generation 2: mt2712, mt6779, mt8173 and mt8183.
+
+  There's slight differences between the two SMI, for generation 2, the
+  register which control the iommu port is at each larb's register base. But
+  for generation 1, the register is at smi ao base(smi always on register
+  base). Besides that, the smi async clock should be prepared and enabled for

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml line 33

Quoted 10 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml new file +10 -0
+  SMI generation 1 to transform the smi clock into emi clock domain, but that is
+  not needed for SMI generation 2.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-smi-common
+      - mediatek,mt2712-smi-common
+      - mediatek,mt6779-smi-common
+      - mediatek,mt7623-smi-common, mediatek,mt2701-smi-common

Same problem here.

Quoted 135 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml new file +63 -0
+      - mediatek,mt8173-smi-common
+      - mediatek,mt8183-smi-common
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: |
+      apb and smi are mandatory. the async is only for generation 1 smi HW.
+      gals(global async local sync) also is optional, here is the list which
+      require gals: mt6779 and mt8183.
+    minItems: 2
+    maxItems: 4
+    items:
+      - description: apb is Advanced Peripheral Bus clock, It's the clock for
+          setting the register.
+      - description: smi is the clock for transfer data and command.
+      - description: async is asynchronous clock, it help transform the smi clock
+          into the emi clock domain.
+      - description: gals0 is the path0 clock of gals.
+      - description: gals1 is the path1 clock of gals.
+
+  clock-names:
+    oneOf:
+      - items:
+          - const: apb
+          - const: smi
+      - items:
+          - const: apb
+          - const: smi
+          - const: async
+      - items:
+          - const: apb
+          - const: smi
+          - const: gals0
+          - const: gals1
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/power/mt8173-power.h>
+
+    smi_common: smi@14022000 {
+            compatible = "mediatek,mt8173-smi-common";
+            reg = <0x14022000 0x1000>;
+            power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+            clocks = <&mmsys CLK_MM_SMI_COMMON>,
+                     <&mmsys CLK_MM_SMI_COMMON>;
+            clock-names = "apb", "smi";
+    };
+
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt deleted +0 -49
deleted file mode 100644
index 8f19dfe7d80e..000000000000
@@ -1,49 +0,0 @@
-SMI (Smart Multimedia Interface) Local Arbiter
-
-The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
-
-Required properties:
-- compatible : must be one of :
-		"mediatek,mt2701-smi-larb"
-		"mediatek,mt2712-smi-larb"
-		"mediatek,mt6779-smi-larb"
-		"mediatek,mt7623-smi-larb", "mediatek,mt2701-smi-larb"
-		"mediatek,mt8173-smi-larb"
-		"mediatek,mt8183-smi-larb"
-- reg : the register and size of this local arbiter.
-- mediatek,smi : a phandle to the smi_common node.
-- power-domains : a phandle to the power domain of this local arbiter.
-- clocks : Must contain an entry for each entry in clock-names.
-- clock-names: must contain 2 entries, as follows:
-  - "apb" : Advanced Peripheral Bus clock, It's the clock for setting
-	    the register.
-  - "smi" : It's the clock for transfer data and command.
-  and this optional clock name:
-  - "gals": the clock for GALS(Global Async Local Sync).
-  Here is the list which has this GALS: mt8183.
-
-Required property for mt2701, mt2712, mt6779 and mt7623:
-- mediatek,larb-id :the hardware id of this larb.
-
-Example:
-	larb1: larb@16010000 {
-		compatible = "mediatek,mt8173-smi-larb";
-		reg = <0 0x16010000 0 0x1000>;
-		mediatek,smi = <&smi_common>;
-		power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>;
-		clocks = <&vdecsys CLK_VDEC_CKEN>,
-			 <&vdecsys CLK_VDEC_LARB_CKEN>;
-		clock-names = "apb", "smi";
-	};
-
-Example for mt2701:
-	larb0: larb@14010000 {
-		compatible = "mediatek,mt2701-smi-larb";
-		reg = <0 0x14010000 0 0x1000>;
-		mediatek,smi = <&smi_common>;
-		mediatek,larb-id = <0>;
-		clocks = <&mmsys CLK_MM_SMI_LARB0>,
-			 <&mmsys CLK_MM_SMI_LARB0>;
-		clock-names = "apb", "smi";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
-	};
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +11 -0
new file mode 100644
index 000000000000..e8919f280c84
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/mediatek,smi-larb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SMI (Smart Multimedia Interface) Local Arbiter
+
+maintainers:
+  - Yong Wu <[email protected]>
+

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml line 21

Quoted 10 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +10 -0
+description: |+
+  The hardware block diagram please check bindings/iommu/mediatek,iommu.yaml
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-smi-larb
+      - mediatek,mt2712-smi-larb
+      - mediatek,mt6779-smi-larb
+      - mediatek,mt7623-smi-larb, mediatek,mt2701-smi-larb

And here.

Quoted 29 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +29 -0
+      - mediatek,mt8173-smi-larb
+      - mediatek,mt8183-smi-larb
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: |
+      apb and smi are mandatory. gals(global async local sync) is optional,
+      here is the list which require gals: mt8183.
+    minItems: 2
+    maxItems: 3
+    items:
+       - description: apb is Advanced Peripheral Bus clock, It's the clock for
+           setting the register.
+       - description: smi is the clock for transfer data and command.
+       - description: the clock for gals.
+
+  clock-names:
+    oneOf:
+      - items:
+         - const: apb
+         - const: smi
+      - items:
+         - const: apb
+         - const: smi
+         - const: gals
+
+  power-domains:

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml line 60

Quoted 10 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +10 -0
+    maxItems: 1
+
+  mediatek,smi:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: a phandle to the smi_common node.
+
+  mediatek,larb-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: the hardware id of this larb.
+      Required property for mt2701, mt2712, mt6779 and mt7623.

Is there a set of valid values?

Quoted 27 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +25 -0
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/power/mt8173-power.h>
+
+    larb1: larb@16010000 {
+      compatible = "mediatek,mt8173-smi-larb";
+      reg = <0x16010000 0x1000>;
+      mediatek,smi = <&smi_common>;
+      power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>;
+      clocks = <&vdecsys CLK_VDEC_CKEN>,
+               <&vdecsys CLK_VDEC_LARB_CKEN>;
+      clock-names = "apb", "smi";
+    };
+
Signature · 1 line
2.18.0
author maintainer
#7 lore raw

Re: [PATCH v2 02/23] dt-bindings: memory: mediatek: Convert SMI to DT schema

Quoted 9 lines · Rob Herring
Quoted 8 lines · Yong Wu

Convert MediaTek SMI to DT schema.

---
 .../mediatek,smi-common.txt                   | 49 ----------
 .../mediatek,smi-common.yaml                  | 96 +++++++++++++++++++
 .../memory-controllers/mediatek,smi-larb.txt  | 49 ----------
 .../memory-controllers/mediatek,smi-larb.yaml | 85 ++++++++++++++++

[...]

Quoted 10 lines

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml line 60

Quoted 8 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +8 -0
+  mediatek,smi:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: a phandle to the smi_common node.
+
+  mediatek,larb-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: the hardware id of this larb.
+      Required property for mt2701, mt2712, mt6779 and mt7623.

Is there a set of valid values?

In the patch[4/23], I change the larb_nr to 32. normally this id is from 0 to 31. I will add this in next version:

    minimum: 0
    maximum: 31
Quoted 20 lines
Quoted 20 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +19 -0
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/power/mt8173-power.h>
+
+    larb1: larb@16010000 {
+      compatible = "mediatek,mt8173-smi-larb";
+      reg = <0x16010000 0x1000>;
+      mediatek,smi = <&smi_common>;
Quoted 8 lines
Quoted 8 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file +6 -0
+      power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>;
+      clocks = <&vdecsys CLK_VDEC_CKEN>,
+               <&vdecsys CLK_VDEC_LARB_CKEN>;
+      clock-names = "apb", "smi";
+    };
+
Signature · 1 line
2.18.0

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

author maintainer
#8 lore raw

PATCH v2 3/23 dt-bindings: memory: mediatek: Add a common larb-port header file

In reply to Yong Wu

Put all the macros about smi larb/port togethers, this is a preparing patch for extending LARB_NR and adding new dom-id support.

---
 include/dt-bindings/memory/mt2712-larb-port.h  |  2 +-
 include/dt-bindings/memory/mt6779-larb-port.h  |  2 +-
 include/dt-bindings/memory/mt8173-larb-port.h  |  2 +-
 include/dt-bindings/memory/mt8183-larb-port.h  |  2 +-
 include/dt-bindings/memory/mtk-smi-larb-port.h | 15 +++++++++++++++
 5 files changed, 19 insertions(+), 4 deletions(-)
 create mode 100644 include/dt-bindings/memory/mtk-smi-larb-port.h
include/dt-bindings/memory/mt2712-larb-port.h +1 -1
index 6f9aa7349cef..b6b2c6bf4459 100644
@@ -6,7 +6,7 @@
 #ifndef __DTS_IOMMU_PORT_MT2712_H
 #define __DTS_IOMMU_PORT_MT2712_H
 
-#define MTK_M4U_ID(larb, port)		(((larb) << 5) | (port))
+#include <dt-bindings/memory/mtk-smi-larb-port.h>
 
 #define M4U_LARB0_ID			0
 #define M4U_LARB1_ID			1
include/dt-bindings/memory/mt6779-larb-port.h +1 -1
index 2ad0899fbf2f..60f57f54393e 100644
@@ -7,7 +7,7 @@
 #ifndef _DTS_IOMMU_PORT_MT6779_H_
 #define _DTS_IOMMU_PORT_MT6779_H_
 
-#define MTK_M4U_ID(larb, port)		 (((larb) << 5) | (port))
+#include <dt-bindings/memory/mtk-smi-larb-port.h>
 
 #define M4U_LARB0_ID			 0
 #define M4U_LARB1_ID			 1
include/dt-bindings/memory/mt8173-larb-port.h +1 -1
index 9f31ccfeca21..d8c99c946053 100644
@@ -6,7 +6,7 @@
 #ifndef __DTS_IOMMU_PORT_MT8173_H
 #define __DTS_IOMMU_PORT_MT8173_H
 
-#define MTK_M4U_ID(larb, port)		(((larb) << 5) | (port))
+#include <dt-bindings/memory/mtk-smi-larb-port.h>
 
 #define M4U_LARB0_ID			0
 #define M4U_LARB1_ID			1
include/dt-bindings/memory/mt8183-larb-port.h +1 -1
index 2c579f305162..275c095a6fd6 100644
@@ -6,7 +6,7 @@
 #ifndef __DTS_IOMMU_PORT_MT8183_H
 #define __DTS_IOMMU_PORT_MT8183_H
 
-#define MTK_M4U_ID(larb, port)		(((larb) << 5) | (port))
+#include <dt-bindings/memory/mtk-smi-larb-port.h>
 
 #define M4U_LARB0_ID			0
 #define M4U_LARB1_ID			1
include/dt-bindings/memory/mtk-smi-larb-port.h new file +15 -0
new file mode 100644
index 000000000000..2ec7fe5ce4e9
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020 MediaTek Inc.
+ * Author: Yong Wu <[email protected]>
+ */
+#ifndef __DTS_MTK_IOMMU_PORT_H_
+#define __DTS_MTK_IOMMU_PORT_H_
+
+#define MTK_LARB_NR_MAX			16
+
+#define MTK_M4U_ID(larb, port)		(((larb) << 5) | (port))
+#define MTK_M4U_TO_LARB(id)		(((id) >> 5) & 0xf)
+#define MTK_M4U_TO_PORT(id)		((id) & 0x1f)
+
+#endif
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#9 lore raw

PATCH v2 4/23 dt-bindings: memory: mediatek: Extend LARB_NR_MAX to 32

In reply to Yong Wu

Extend the max larb number definition as mt8192 has larb_nr over 16.

---
 include/dt-bindings/memory/mtk-smi-larb-port.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
include/dt-bindings/memory/mtk-smi-larb-port.h +2 -2
index 2ec7fe5ce4e9..f4d8e3aed0bc 100644
@@ -6,10 +6,10 @@
 #ifndef __DTS_MTK_IOMMU_PORT_H_
 #define __DTS_MTK_IOMMU_PORT_H_
 
-#define MTK_LARB_NR_MAX			16
+#define MTK_LARB_NR_MAX			32
 
 #define MTK_M4U_ID(larb, port)		(((larb) << 5) | (port))
-#define MTK_M4U_TO_LARB(id)		(((id) >> 5) & 0xf)
+#define MTK_M4U_TO_LARB(id)		(((id) >> 5) & 0x1f)
 #define MTK_M4U_TO_PORT(id)		((id) & 0x1f)
 
 #endif
Signature · 1 line
2.18.0
author maintainer
#10 lore raw

PATCH v2 5/23 dt-bindings: memory: mediatek: Add domain definition

In reply to Yong Wu

In the latest SoC, there are several HW IP require a sepecial iova range, mainly CCU and VPU has this requirement. Take CCU as a example, CCU require its iova locate in the range(0x4000_0000 ~ 0x43ff_ffff).

In this patch we add a domain definition for the special port. In the example of CCU, If we preassign CCU port in domain1, then iommu driver will prepare a independent iommu domain of the special iova range for it, then the iova got from dma_alloc_attrs(ccu-dev) will locate in its special range.

This is a preparing patch for multi-domain support.

---
 include/dt-bindings/memory/mtk-smi-larb-port.h | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
include/dt-bindings/memory/mtk-smi-larb-port.h +8 -1
index f4d8e3aed0bc..d00f5de8438b 100644
@@ -7,9 +7,16 @@
 #define __DTS_MTK_IOMMU_PORT_H_
 
 #define MTK_LARB_NR_MAX			32
+#define MTK_M4U_DOM_NR_MAX		8
+
+#define MTK_M4U_DOM_ID(domid, larb, port)	\
+	(((domid) & 0x7) << 16 | (((larb) & 0x1f) << 5) | ((port) & 0x1f))
+
+/* The default dom id is 0. */
+#define MTK_M4U_ID(larb, port)		MTK_M4U_DOM_ID(0, larb, port)
 
-#define MTK_M4U_ID(larb, port)		(((larb) << 5) | (port))
 #define MTK_M4U_TO_LARB(id)		(((id) >> 5) & 0x1f)
 #define MTK_M4U_TO_PORT(id)		((id) & 0x1f)
+#define MTK_M4U_TO_DOM(id)		(((id) >> 16) & 0x7)
 
 #endif
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#11 lore raw

PATCH v2 6/23 dt-bindings: mediatek: Add binding for mt8192 IOMMU and SMI

In reply to Yong Wu

This patch adds decriptions for mt8192 IOMMU and SMI.

mt8192 also is MTK IOMMU gen2 which uses ARM Short-Descriptor translation table format. The M4U-SMI HW diagram is as below:

                          EMI
                           |
                          M4U
                           |
                      ------------
                       SMI Common
                      ------------
                           |
  +-------+------+------+----------------------+-------+
  |       |      |      |       ......         |       |
  |       |      |      |                      |       |
larb0   larb1  larb2  larb4     ......      larb19   larb20
disp0   disp1   mdp    vdec                   IPE      IPE

All the connections are HW fixed, SW can NOT adjust it.

mt8192 M4U support 0~16GB iova range. we preassign different engines into different iova ranges:

domain-id  module     iova-range                  larbs
   0       disp        0 ~ 4G                      larb0/1
   1       vcodec      4G ~ 8G                     larb4/5/7
   2       cam/mdp     8G ~ 12G             larb2/9/11/13/14/16/17/18/19/20
   3       CCU0    0x4000_0000 ~ 0x43ff_ffff     larb13: port 9/10
   4       CCU1    0x4400_0000 ~ 0x47ff_ffff     larb14: port 4/5

The iova range for CCU0/1(camera control unit) is HW requirement.

---
 .../bindings/iommu/mediatek,iommu.yaml        |   9 +-
 .../mediatek,smi-common.yaml                  |   5 +-
 .../memory-controllers/mediatek,smi-larb.yaml |   3 +-
 include/dt-bindings/memory/mt8192-larb-port.h | 239 ++++++++++++++++++
 4 files changed, 251 insertions(+), 5 deletions(-)
 create mode 100644 include/dt-bindings/memory/mt8192-larb-port.h
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml +7 -2
index d7b31bda3e35..f55fcdee90d1 100644
@@ -76,6 +76,7 @@ properties:
       - mediatek,mt7623-m4u, mediatek,mt2701-m4u #mt7623 generation one HW
       - mediatek,mt8173-m4u #mt8173 generation two HW
       - mediatek,mt8183-m4u #mt8183 generation two HW
+      - mediatek,mt8192-m4u #mt8192 generation two HW
 
   reg:
     maxItems: 1
@@ -86,7 +87,7 @@ properties:
   clocks:
     description: |
       bclk is optional. here is the list which require this bclk:
-      mt2701, mt2712, mt7623 and mt8173.
+      mt2701, mt2712, mt7623, mt8173 and mt8192.
       M4U will use the EMI clock which always has been enabled before
       kernel if there is no this bclk.
     items:
@@ -112,7 +113,11 @@ properties:
       dt-binding/memory/mt2712-larb-port.h for mt2712,
       dt-binding/memory/mt6779-larb-port.h for mt6779,
       dt-binding/memory/mt8173-larb-port.h for mt8173,
-      dt-binding/memory/mt8183-larb-port.h for mt8183.
+      dt-binding/memory/mt8183-larb-port.h for mt8183,
+      dt-binding/memory/mt8192-larb-port.h for mt8192.
+
+  power-domains:
+    maxItems: 1
 
 required:
   - compatible
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml +3 -2
index 781d7b7617d9..bbf6062433fa 100644
@@ -15,7 +15,7 @@ description: |+
   MediaTek SMI have two generations of HW architecture, here is the list
   which generation the SoCs use:
   generation 1: mt2701 and mt7623.
-  generation 2: mt2712, mt6779, mt8173 and mt8183.
+  generation 2: mt2712, mt6779, mt8173, mt8183 and mt8192.
 
   There's slight differences between the two SMI, for generation 2, the
   register which control the iommu port is at each larb's register base. But
@@ -33,6 +33,7 @@ properties:
       - mediatek,mt7623-smi-common, mediatek,mt2701-smi-common
       - mediatek,mt8173-smi-common
       - mediatek,mt8183-smi-common
+      - mediatek,mt8192-smi-common
 
   reg:
     maxItems: 1
@@ -41,7 +42,7 @@ properties:
     description: |
       apb and smi are mandatory. the async is only for generation 1 smi HW.
       gals(global async local sync) also is optional, here is the list which
-      require gals: mt6779 and mt8183.
+      require gals: mt6779, mt8183 and mt8192.
     minItems: 2
     maxItems: 4
     items:
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml +2 -1
index e8919f280c84..fa0137d794ba 100644
@@ -21,6 +21,7 @@ properties:
       - mediatek,mt7623-smi-larb, mediatek,mt2701-smi-larb
       - mediatek,mt8173-smi-larb
       - mediatek,mt8183-smi-larb
+      - mediatek,mt8192-smi-larb
 
   reg:
     maxItems: 1
@@ -57,7 +58,7 @@ properties:
   mediatek,larb-id:
     $ref: /schemas/types.yaml#/definitions/uint32
     description: the hardware id of this larb.
-      Required property for mt2701, mt2712, mt6779 and mt7623.
+      Required property for mt2701, mt2712, mt6779, mt7623 and mt8192.
 
 required:
   - compatible
include/dt-bindings/memory/mt8192-larb-port.h new file +239 -0

239 lines not on this page · raw message

Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
maintainer Reviewed-by on v2 6/23
#12 lore raw

Re: [PATCH v2 06/23] dt-bindings: mediatek: Add binding for mt8192 IOMMU and SMI

Quoted 33 lines · Yong Wu

This patch adds decriptions for mt8192 IOMMU and SMI.

mt8192 also is MTK IOMMU gen2 which uses ARM Short-Descriptor translation table format. The M4U-SMI HW diagram is as below:

                          EMI
                           |
                          M4U
                           |
                      ------------
                       SMI Common
                      ------------
                           |
  +-------+------+------+----------------------+-------+
  |       |      |      |       ......         |       |
  |       |      |      |                      |       |
larb0   larb1  larb2  larb4     ......      larb19   larb20
disp0   disp1   mdp    vdec                   IPE      IPE

All the connections are HW fixed, SW can NOT adjust it.

mt8192 M4U support 0~16GB iova range. we preassign different engines into different iova ranges:

domain-id  module     iova-range                  larbs
   0       disp        0 ~ 4G                      larb0/1
   1       vcodec      4G ~ 8G                     larb4/5/7
   2       cam/mdp     8G ~ 12G             larb2/9/11/13/14/16/17/18/19/20
   3       CCU0    0x4000_0000 ~ 0x43ff_ffff     larb13: port 9/10
   4       CCU1    0x4400_0000 ~ 0x47ff_ffff     larb14: port 4/5

The iova range for CCU0/1(camera control unit) is HW requirement.

Quoted 9 lines
---
 .../bindings/iommu/mediatek,iommu.yaml        |   9 +-
 .../mediatek,smi-common.yaml                  |   5 +-
 .../memory-controllers/mediatek,smi-larb.yaml |   3 +-
 include/dt-bindings/memory/mt8192-larb-port.h | 239 ++++++++++++++++++
 4 files changed, 251 insertions(+), 5 deletions(-)
 create mode 100644 include/dt-bindings/memory/mt8192-larb-port.h

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

author maintainer
#13 lore raw

PATCH v2 7/23 iommu/mediatek: Use the common mtk-smi-larb-port.h

In reply to Yong Wu

Use the common larb-port header in the source code.

---
 drivers/iommu/mtk_iommu.c  | 7 -------
 drivers/iommu/mtk_iommu.h  | 1 +
 drivers/memory/mtk-smi.c   | 1 +
 include/soc/mediatek/smi.h | 2 --
 4 files changed, 2 insertions(+), 9 deletions(-)
drivers/iommu/mtk_iommu.c +0 -7
index 785b228d39a6..fd8322ee4980 100644
@@ -101,13 +101,6 @@
 
 #define MTK_PROTECT_PA_ALIGN			256
 
-/*
- * Get the local arbiter ID and the portid within the larb arbiter
- * from mtk_m4u_id which is defined by MTK_M4U_ID.
- */
-#define MTK_M4U_TO_LARB(id)		(((id) >> 5) & 0xf)
-#define MTK_M4U_TO_PORT(id)		((id) & 0x1f)
-
 #define HAS_4GB_MODE			BIT(0)
 /* HW will use the EMI clock if there isn't the "bclk". */
 #define HAS_BCLK			BIT(1)
drivers/iommu/mtk_iommu.h +1 -0
index 122925dbe547..a2e2c844b96e 100644
@@ -17,6 +17,7 @@
 #include <linux/spinlock.h>
 #include <linux/dma-mapping.h>
 #include <soc/mediatek/smi.h>
+#include <dt-bindings/memory/mtk-smi-larb-port.h>
 
 #define MTK_LARB_COM_MAX	8
 #define MTK_LARB_SUBCOM_MAX	4
drivers/memory/mtk-smi.c +1 -0
index c21262502581..ec83f1ac48b1 100644
@@ -14,6 +14,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <soc/mediatek/smi.h>
+#include <dt-bindings/memory/mtk-smi-larb-port.h>
 #include <dt-bindings/memory/mt2701-larb-port.h>
 
 /* mt8173 */
include/soc/mediatek/smi.h +0 -2
index 5a34b87d89e3..9371bf572ab8 100644
@@ -11,8 +11,6 @@
 
 #ifdef CONFIG_MTK_SMI
 
-#define MTK_LARB_NR_MAX		16
-
 #define MTK_SMI_MMU_EN(port)	BIT(port)
 
 struct mtk_smi_larb_iommu {
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#14 lore raw

PATCH v2 8/23 iommu/io-pgtable-arm-v7s: Use ias to check the valid iova in unmap

In reply to Yong Wu

As title.
BTW, change the ias/oas checking format in v7s_map.

---
 drivers/iommu/io-pgtable-arm-v7s.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/iommu/io-pgtable-arm-v7s.c +2 -3
index a688f22cbe3b..4c9d8dccfc5a 100644
@@ -526,8 +526,7 @@ static int arm_v7s_map(struct io_pgtable_ops *ops, unsigned long iova,
 	if (!(prot & (IOMMU_READ | IOMMU_WRITE)))
 		return 0;
 
-	if (WARN_ON(iova >= (1ULL << data->iop.cfg.ias) ||
-		    paddr >= (1ULL << data->iop.cfg.oas)))
+	if (WARN_ON(iova >> data->iop.cfg.ias || paddr >> data->iop.cfg.oas))
 		return -ERANGE;
 
 	ret = __arm_v7s_map(data, iova, paddr, size, prot, 1, data->pgd, gfp);
@@ -717,7 +716,7 @@ static size_t arm_v7s_unmap(struct io_pgtable_ops *ops, unsigned long iova,
 {
 	struct arm_v7s_io_pgtable *data = io_pgtable_ops_to_data(ops);
 
-	if (WARN_ON(upper_32_bits(iova)))
+	if (WARN_ON(iova >> data->iop.cfg.ias))
 		return 0;
 
 	return __arm_v7s_unmap(data, gather, iova, size, 1, data->pgd);
Signature · 1 line
2.18.0
author maintainer
#15 lore raw

PATCH v2 9/23 iommu/io-pgtable-arm-v7s: Extend PA34 for MediaTek

In reply to Yong Wu

MediaTek extend the bit5 in lvl1 and lvl2 descriptor as PA34.

---
 drivers/iommu/io-pgtable-arm-v7s.c | 9 +++++++--
 drivers/iommu/mtk_iommu.c          | 2 +-
 include/linux/io-pgtable.h         | 4 ++--
 3 files changed, 10 insertions(+), 5 deletions(-)
drivers/iommu/io-pgtable-arm-v7s.c +7 -2
index 4c9d8dccfc5a..a3b3e9147b8d 100644
@@ -112,9 +112,10 @@
 #define ARM_V7S_TEX_MASK		0x7
 #define ARM_V7S_ATTR_TEX(val)		(((val) & ARM_V7S_TEX_MASK) << ARM_V7S_TEX_SHIFT)
 
-/* MediaTek extend the two bits for PA 32bit/33bit */
+/* MediaTek extend the bits below for PA 32bit/33bit/34bit */
 #define ARM_V7S_ATTR_MTK_PA_BIT32	BIT(9)
 #define ARM_V7S_ATTR_MTK_PA_BIT33	BIT(4)
+#define ARM_V7S_ATTR_MTK_PA_BIT34	BIT(5)
 
 /* *well, except for TEX on level 2 large pages, of course :( */
 #define ARM_V7S_CONT_PAGE_TEX_SHIFT	6
@@ -194,6 +195,8 @@ static arm_v7s_iopte paddr_to_iopte(phys_addr_t paddr, int lvl,
 		pte |= ARM_V7S_ATTR_MTK_PA_BIT32;
 	if (paddr & BIT_ULL(33))
 		pte |= ARM_V7S_ATTR_MTK_PA_BIT33;
+	if (paddr & BIT_ULL(34))
+		pte |= ARM_V7S_ATTR_MTK_PA_BIT34;
 	return pte;
 }
 
@@ -218,6 +221,8 @@ static phys_addr_t iopte_to_paddr(arm_v7s_iopte pte, int lvl,
 		paddr |= BIT_ULL(32);
 	if (pte & ARM_V7S_ATTR_MTK_PA_BIT33)
 		paddr |= BIT_ULL(33);
+	if (pte & ARM_V7S_ATTR_MTK_PA_BIT34)
+		paddr |= BIT_ULL(34);
 	return paddr;
 }
 
@@ -753,7 +758,7 @@ static struct io_pgtable *arm_v7s_alloc_pgtable(struct io_pgtable_cfg *cfg,
 	if (cfg->ias > ARM_V7S_ADDR_BITS)
 		return NULL;
 
-	if (cfg->oas > (arm_v7s_is_mtk_enabled(cfg) ? 34 : ARM_V7S_ADDR_BITS))
+	if (cfg->oas > (arm_v7s_is_mtk_enabled(cfg) ? 35 : ARM_V7S_ADDR_BITS))
 		return NULL;
 
 	if (cfg->quirks & ~(IO_PGTABLE_QUIRK_ARM_NS |
drivers/iommu/mtk_iommu.c +1 -1
index fd8322ee4980..f6a2e3eb59d2 100644
@@ -317,7 +317,7 @@ static int mtk_iommu_domain_finalise(struct mtk_iommu_domain *dom)
 			IO_PGTABLE_QUIRK_ARM_MTK_EXT,
 		.pgsize_bitmap = mtk_iommu_ops.pgsize_bitmap,
 		.ias = 32,
-		.oas = 34,
+		.oas = 35,
 		.tlb = &mtk_iommu_flush_ops,
 		.iommu_dev = data->dev,
 	};
include/linux/io-pgtable.h +2 -2
index 23285ba645db..8c9a889d8df9 100644
@@ -77,8 +77,8 @@ struct io_pgtable_cfg {
 	 *	TLB maintenance when mapping as well as when unmapping.
 	 *
 	 * IO_PGTABLE_QUIRK_ARM_MTK_EXT: (ARM v7s format) MediaTek IOMMUs extend
-	 *	to support up to 34 bits PA where the bit32 and bit33 are
-	 *	encoded in the bit9 and bit4 of the PTE respectively.
+	 *	to support up to 35 bits PA where the bit32, bit33 and bit34 are
+	 *	encoded in the bit9, bit4 and bit5 of the PTE respectively.
 	 *
 	 * IO_PGTABLE_QUIRK_NON_STRICT: Skip issuing synchronous leaf TLBIs
 	 *	on unmap, for DMA domains using the flush queue mechanism for
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#16 lore raw

PATCH v2 10/23 iommu/io-pgtable-arm-v7s: Add cfg as a param in some macros

In reply to Yong Wu

Add "cfg" as a parameter for some macros. This is a preparing patch for mediatek extend the lvl1 pgtable. No functional change.

---
 drivers/iommu/io-pgtable-arm-v7s.c | 34 +++++++++++++++---------------
 1 file changed, 17 insertions(+), 17 deletions(-)
drivers/iommu/io-pgtable-arm-v7s.c +17 -17
index a3b3e9147b8d..8362fdf76657 100644
@@ -53,17 +53,17 @@
 #define ARM_V7S_LVL_SHIFT(lvl)		(ARM_V7S_ADDR_BITS - (4 + 8 * (lvl)))
 #define ARM_V7S_TABLE_SHIFT		10
 
-#define ARM_V7S_PTES_PER_LVL(lvl)	(1 << _ARM_V7S_LVL_BITS(lvl))
-#define ARM_V7S_TABLE_SIZE(lvl)						\
-	(ARM_V7S_PTES_PER_LVL(lvl) * sizeof(arm_v7s_iopte))
+#define ARM_V7S_PTES_PER_LVL(lvl, cfg)	(1 << _ARM_V7S_LVL_BITS(lvl))
+#define ARM_V7S_TABLE_SIZE(lvl, cfg)					\
+	(ARM_V7S_PTES_PER_LVL(lvl, cfg) * sizeof(arm_v7s_iopte))
 
 #define ARM_V7S_BLOCK_SIZE(lvl)		(1UL << ARM_V7S_LVL_SHIFT(lvl))
 #define ARM_V7S_LVL_MASK(lvl)		((u32)(~0U << ARM_V7S_LVL_SHIFT(lvl)))
 #define ARM_V7S_TABLE_MASK		((u32)(~0U << ARM_V7S_TABLE_SHIFT))
-#define _ARM_V7S_IDX_MASK(lvl)		(ARM_V7S_PTES_PER_LVL(lvl) - 1)
-#define ARM_V7S_LVL_IDX(addr, lvl)	({				\
+#define _ARM_V7S_IDX_MASK(lvl, cfg)	(ARM_V7S_PTES_PER_LVL(lvl, cfg) - 1)
+#define ARM_V7S_LVL_IDX(addr, lvl, cfg)	({			\
 	int _l = lvl;							\
-	((u32)(addr) >> ARM_V7S_LVL_SHIFT(_l)) & _ARM_V7S_IDX_MASK(_l); \
+	((u32)(addr) >> ARM_V7S_LVL_SHIFT(_l)) & _ARM_V7S_IDX_MASK(_l, cfg); \
 })
 
 /*
@@ -239,7 +239,7 @@ static void *__arm_v7s_alloc_table(int lvl, gfp_t gfp,
 	struct device *dev = cfg->iommu_dev;
 	phys_addr_t phys;
 	dma_addr_t dma;
-	size_t size = ARM_V7S_TABLE_SIZE(lvl);
+	size_t size = ARM_V7S_TABLE_SIZE(lvl, cfg);
 	void *table = NULL;
 
 	if (lvl == 1)
@@ -285,7 +285,7 @@ static void __arm_v7s_free_table(void *table, int lvl,
 {
 	struct io_pgtable_cfg *cfg = &data->iop.cfg;
 	struct device *dev = cfg->iommu_dev;
-	size_t size = ARM_V7S_TABLE_SIZE(lvl);
+	size_t size = ARM_V7S_TABLE_SIZE(lvl, cfg);
 
 	if (!cfg->coherent_walk)
 		dma_unmap_single(dev, __arm_v7s_dma_addr(table), size,
@@ -429,7 +429,7 @@ static int arm_v7s_init_pte(struct arm_v7s_io_pgtable *data,
 			arm_v7s_iopte *tblp;
 			size_t sz = ARM_V7S_BLOCK_SIZE(lvl);
 
-			tblp = ptep - ARM_V7S_LVL_IDX(iova, lvl);
+			tblp = ptep - ARM_V7S_LVL_IDX(iova, lvl, cfg);
 			if (WARN_ON(__arm_v7s_unmap(data, NULL, iova + i * sz,
 						    sz, lvl, tblp) != sz))
 				return -EINVAL;
@@ -482,7 +482,7 @@ static int __arm_v7s_map(struct arm_v7s_io_pgtable *data, unsigned long iova,
 	int num_entries = size >> ARM_V7S_LVL_SHIFT(lvl);
 
 	/* Find our entry at the current level */
-	ptep += ARM_V7S_LVL_IDX(iova, lvl);
+	ptep += ARM_V7S_LVL_IDX(iova, lvl, cfg);
 
 	/* If we can install a leaf entry at this level, then do so */
 	if (num_entries)
@@ -554,7 +554,7 @@ static void arm_v7s_free_pgtable(struct io_pgtable *iop)
 	struct arm_v7s_io_pgtable *data = io_pgtable_to_data(iop);
 	int i;
 
-	for (i = 0; i < ARM_V7S_PTES_PER_LVL(1); i++) {
+	for (i = 0; i < ARM_V7S_PTES_PER_LVL(1, &data->iop.cfg); i++) {
 		arm_v7s_iopte pte = data->pgd[i];
 
 		if (ARM_V7S_PTE_IS_TABLE(pte, 1))
@@ -606,9 +606,9 @@ static size_t arm_v7s_split_blk_unmap(struct arm_v7s_io_pgtable *data,
 	if (!tablep)
 		return 0; /* Bytes unmapped */
 
-	num_ptes = ARM_V7S_PTES_PER_LVL(2);
+	num_ptes = ARM_V7S_PTES_PER_LVL(2, cfg);
 	num_entries = size >> ARM_V7S_LVL_SHIFT(2);
-	unmap_idx = ARM_V7S_LVL_IDX(iova, 2);
+	unmap_idx = ARM_V7S_LVL_IDX(iova, 2, cfg);
 
 	pte = arm_v7s_prot_to_pte(arm_v7s_pte_to_prot(blk_pte, 1), 2, cfg);
 	if (num_entries > 1)
@@ -650,7 +650,7 @@ static size_t __arm_v7s_unmap(struct arm_v7s_io_pgtable *data,
 	if (WARN_ON(lvl > 2))
 		return 0;
 
-	idx = ARM_V7S_LVL_IDX(iova, lvl);
+	idx = ARM_V7S_LVL_IDX(iova, lvl, &iop->cfg);
 	ptep += idx;
 	do {
 		pte[i] = READ_ONCE(ptep[i]);
@@ -736,7 +736,7 @@ static phys_addr_t arm_v7s_iova_to_phys(struct io_pgtable_ops *ops,
 	u32 mask;
 
 	do {
-		ptep += ARM_V7S_LVL_IDX(iova, ++lvl);
+		ptep += ARM_V7S_LVL_IDX(iova, ++lvl, &data->iop.cfg);
 		pte = READ_ONCE(*ptep);
 		ptep = iopte_deref(pte, lvl, data);
 	} while (ARM_V7S_PTE_IS_TABLE(pte, lvl));
@@ -779,8 +779,8 @@ static struct io_pgtable *arm_v7s_alloc_pgtable(struct io_pgtable_cfg *cfg,
 
 	spin_lock_init(&data->split_lock);
 	data->l2_tables = kmem_cache_create("io-pgtable_armv7s_l2",
-					    ARM_V7S_TABLE_SIZE(2),
-					    ARM_V7S_TABLE_SIZE(2),
+					    ARM_V7S_TABLE_SIZE(2, cfg),
+					    ARM_V7S_TABLE_SIZE(2, cfg),
 					    ARM_V7S_TABLE_SLAB_FLAGS, NULL);
 	if (!data->l2_tables)
 		goto out_free_data;
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#17 lore raw

PATCH v2 11/23 iommu/io-pgtable-arm-v7s: Quad lvl1 pgtable for MediaTek

In reply to Yong Wu

The standard input iova bits is 32. MediaTek quad the lvl1 pagetable (4 * lvl1). No change for lvl2 pagetable. Then the iova bits can reach 34bit.

---
 drivers/iommu/io-pgtable-arm-v7s.c | 13 ++++++++++---
 drivers/iommu/mtk_iommu.c          |  2 +-
 2 files changed, 11 insertions(+), 4 deletions(-)
drivers/iommu/io-pgtable-arm-v7s.c +10 -3
index 8362fdf76657..0e97ca978c04 100644
@@ -50,10 +50,17 @@
  */
 #define ARM_V7S_ADDR_BITS		32
 #define _ARM_V7S_LVL_BITS(lvl)		(16 - (lvl) * 4)
+/* MediaTek: totally 34bits, 14bits at lvl1 and 8bits at lvl2. */
+#define _ARM_V7S_LVL_BITS_MTK(lvl)	(20 - (lvl) * 6)
 #define ARM_V7S_LVL_SHIFT(lvl)		(ARM_V7S_ADDR_BITS - (4 + 8 * (lvl)))
 #define ARM_V7S_TABLE_SHIFT		10
 
-#define ARM_V7S_PTES_PER_LVL(lvl, cfg)	(1 << _ARM_V7S_LVL_BITS(lvl))
+#define ARM_V7S_PTES_PER_LVL(lvl, cfg)	({				\
+	int _l = lvl;							\
+	!arm_v7s_is_mtk_enabled(cfg) ?					\
+	 (1 << _ARM_V7S_LVL_BITS(_l)) : (1 << _ARM_V7S_LVL_BITS_MTK(_l));\
+})
+
 #define ARM_V7S_TABLE_SIZE(lvl, cfg)					\
 	(ARM_V7S_PTES_PER_LVL(lvl, cfg) * sizeof(arm_v7s_iopte))
 
@@ -63,7 +70,7 @@
 #define _ARM_V7S_IDX_MASK(lvl, cfg)	(ARM_V7S_PTES_PER_LVL(lvl, cfg) - 1)
 #define ARM_V7S_LVL_IDX(addr, lvl, cfg)	({			\
 	int _l = lvl;							\
-	((u32)(addr) >> ARM_V7S_LVL_SHIFT(_l)) & _ARM_V7S_IDX_MASK(_l, cfg); \
+	((addr) >> ARM_V7S_LVL_SHIFT(_l)) & _ARM_V7S_IDX_MASK(_l, cfg); \
 })
 
 /*
@@ -755,7 +762,7 @@ static struct io_pgtable *arm_v7s_alloc_pgtable(struct io_pgtable_cfg *cfg,
 {
 	struct arm_v7s_io_pgtable *data;
 
-	if (cfg->ias > ARM_V7S_ADDR_BITS)
+	if (cfg->ias > (arm_v7s_is_mtk_enabled(cfg) ? 34 : ARM_V7S_ADDR_BITS))
 		return NULL;
 
 	if (cfg->oas > (arm_v7s_is_mtk_enabled(cfg) ? 35 : ARM_V7S_ADDR_BITS))
drivers/iommu/mtk_iommu.c +1 -1
index f6a2e3eb59d2..6e85c9976a33 100644
@@ -316,7 +316,7 @@ static int mtk_iommu_domain_finalise(struct mtk_iommu_domain *dom)
 			IO_PGTABLE_QUIRK_TLBI_ON_MAP |
 			IO_PGTABLE_QUIRK_ARM_MTK_EXT,
 		.pgsize_bitmap = mtk_iommu_ops.pgsize_bitmap,
-		.ias = 32,
+		.ias = 34,
 		.oas = 35,
 		.tlb = &mtk_iommu_flush_ops,
 		.iommu_dev = data->dev,
Signature · 1 line
2.18.0
author maintainer
#18 lore raw

PATCH v2 12/23 iommu/mediatek: Move hw_init into attach_device

In reply to Yong Wu

In attach device, it will update the pagetable base address register. Move the hw_init function also here. Then it only need call pm_runtime_get/put one time here if m4u has power domain.

---
 drivers/iommu/mtk_iommu.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/iommu/mtk_iommu.c +6 -4
index 6e85c9976a33..940b7a9191b2 100644
@@ -122,6 +122,8 @@ struct mtk_iommu_domain {
 
 static const struct iommu_ops mtk_iommu_ops;
 
+static int mtk_iommu_hw_init(const struct mtk_iommu_data *data);
+
 /*
  * In M4U 4GB mode, the physical address is remapped as below:
  *
@@ -377,12 +379,16 @@ static int mtk_iommu_attach_device(struct iommu_domain *domain,
 {
 	struct mtk_iommu_data *data = dev_iommu_priv_get(dev);
 	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
+	int ret;
 
 	if (!data)
 		return -ENODEV;
 
 	/* Update the pgtable base address register of the M4U HW */
 	if (!data->m4u_dom) {
+		ret = mtk_iommu_hw_init(data);
+		if (ret)
+			return ret;
 		data->m4u_dom = dom;
 		writel(dom->cfg.arm_v7s_cfg.ttbr & MMU_PT_ADDR_MASK,
 		       data->base + REG_MMU_PT_BASE_ADDR);
@@ -705,10 +711,6 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, data);
 
-	ret = mtk_iommu_hw_init(data);
-	if (ret)
-		return ret;
-
 	ret = iommu_device_sysfs_add(&data->iommu, dev, NULL,
 				     "mtk-iommu.%pa", &ioaddr);
 	if (ret)
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#19 lore raw

PATCH v2 13/23 iommu/mediatek: Add device link for smi-common and m4u

In reply to Yong Wu

In the lastest SoC, M4U has its special power domain. thus, If the engine begin to work, it should help enable the power for M4U firstly. Currently if the engine work, it always enable the power/clocks for smi-larbs/smi-common. This patch adds device_link for smi-common and M4U. then, if smi-common power is enabled, the M4U power also is powered on automatically.

Normally M4U connect with several smi-larbs and their smi-common always are the same, In this patch it get smi-common dev from the first smi-larb device(i==0), then add the device_link only while m4u has power-domain.

---
 drivers/iommu/mtk_iommu.c | 33 ++++++++++++++++++++++++++++++---
 drivers/iommu/mtk_iommu.h |  1 +
 2 files changed, 31 insertions(+), 3 deletions(-)
drivers/iommu/mtk_iommu.c +30 -3
index 940b7a9191b2..68de59e0d521 100644
@@ -20,6 +20,7 @@
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <asm/barrier.h>
@@ -681,7 +682,7 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 		return larb_nr;
 
 	for (i = 0; i < larb_nr; i++) {
-		struct device_node *larbnode;
+		struct device_node *larbnode, *smicomm_node;
 		struct platform_device *plarbdev;
 		u32 id;
 
@@ -707,6 +708,26 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 
 		component_match_add_release(dev, &match, release_of,
 					    compare_of, larbnode);
+		if (!i) {
+			smicomm_node = of_parse_phandle(larbnode, "mediatek,smi", 0);
+			if (!smicomm_node)
+				return -EINVAL;
+
+			plarbdev = of_find_device_by_node(smicomm_node);
+			of_node_put(smicomm_node);
+			data->smicomm_dev = &plarbdev->dev;
+		}
+	}
+
+	if (dev->pm_domain) {
+		struct device_link *link;
+
+		link = device_link_add(data->smicomm_dev, dev,
+				       DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME);
+		if (!link) {
+			dev_err(dev, "Unable link %s.\n", dev_name(data->smicomm_dev));
+			return -EINVAL;
+		}
 	}
 
 	platform_set_drvdata(pdev, data);
@@ -714,14 +735,14 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 	ret = iommu_device_sysfs_add(&data->iommu, dev, NULL,
 				     "mtk-iommu.%pa", &ioaddr);
 	if (ret)
-		return ret;
+		goto out;
 
 	iommu_device_set_ops(&data->iommu, &mtk_iommu_ops);
 	iommu_device_set_fwnode(&data->iommu, &pdev->dev.of_node->fwnode);
 
 	ret = iommu_device_register(&data->iommu);
 	if (ret)
-		return ret;
+		goto out;
 
 	spin_lock_init(&data->tlb_lock);
 	list_add_tail(&data->list, &m4ulist);
@@ -730,6 +751,10 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 		bus_set_iommu(&platform_bus_type, &mtk_iommu_ops);
 
 	return component_master_add_with_match(dev, &mtk_iommu_com_ops, match);
+out:
+	if (dev->pm_domain)
+		device_link_remove(data->smicomm_dev, dev);
+	return ret;
 }
 
 static int mtk_iommu_remove(struct platform_device *pdev)
@@ -743,6 +768,8 @@ static int mtk_iommu_remove(struct platform_device *pdev)
 		bus_set_iommu(&platform_bus_type, NULL);
 
 	clk_disable_unprepare(data->bclk);
+	if (pdev->dev.pm_domain)
+		device_link_remove(data->smicomm_dev, &pdev->dev);
 	devm_free_irq(&pdev->dev, data->irq, data);
 	component_master_del(&pdev->dev, &mtk_iommu_com_ops);
 	return 0;
drivers/iommu/mtk_iommu.h +1 -0
index a2e2c844b96e..ae7909815cdb 100644
@@ -67,6 +67,7 @@ struct mtk_iommu_data {
 
 	struct iommu_device		iommu;
 	const struct mtk_iommu_plat_data *plat_data;
+	struct device			*smicomm_dev;
 
 	struct dma_iommu_mapping	*mapping; /* For mtk_iommu_v1.c */
 
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#20 lore raw

PATCH v2 14/23 iommu/mediatek: Add power-domain operation

In reply to Yong Wu

In the previous SoC, the M4U HW is in the EMI power domain which is always on. the latest M4U is in the display power domain which may be turned on/off, thus we have to add pm_runtime interface for it.

When the engine work, the engine always enable the power and clocks for smi-larb/smi-common, then the M4U's power will always be powered on automatically via the device link with smi-common.

Note: we don't enable the M4U power in iommu_map/unmap for tlb flush. If its power already is on, of course it is ok. if the power is off, the main tlb will be reset while M4U power on, thus the tlb flush while m4u power off is unnecessary, just skip it.

---
 drivers/iommu/mtk_iommu.c | 33 +++++++++++++++++++++++++++------
 1 file changed, 27 insertions(+), 6 deletions(-)
drivers/iommu/mtk_iommu.c +27 -6
index 68de59e0d521..d22772ec64c8 100644
@@ -196,6 +196,10 @@ static void mtk_iommu_tlb_flush_range_sync(unsigned long iova, size_t size,
 	u32 tmp;
 
 	for_each_m4u(data) {
+		/* skip tlb flush when pm is not active. */
+		if (!pm_runtime_active(data->dev))
+			continue;
+
 		spin_lock_irqsave(&data->tlb_lock, flags);
 		writel_relaxed(F_INVLD_EN1 | F_INVLD_EN0,
 			       data->base + data->plat_data->inv_sel_reg);
@@ -380,6 +384,7 @@ static int mtk_iommu_attach_device(struct iommu_domain *domain,
 {
 	struct mtk_iommu_data *data = dev_iommu_priv_get(dev);
 	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
+	struct device *m4udev = data->dev;
 	int ret;
 
 	if (!data)
@@ -387,12 +392,18 @@ static int mtk_iommu_attach_device(struct iommu_domain *domain,
 
 	/* Update the pgtable base address register of the M4U HW */
 	if (!data->m4u_dom) {
+		ret = pm_runtime_get_sync(m4udev);
+		if (ret < 0)
+			return ret;
 		ret = mtk_iommu_hw_init(data);
-		if (ret)
+		if (ret) {
+			pm_runtime_put(m4udev);
 			return ret;
+		}
 		data->m4u_dom = dom;
 		writel(dom->cfg.arm_v7s_cfg.ttbr & MMU_PT_ADDR_MASK,
 		       data->base + REG_MMU_PT_BASE_ADDR);
+		pm_runtime_put(m4udev);
 	}
 
 	mtk_iommu_config(data, dev, true);
@@ -722,10 +733,13 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 	if (dev->pm_domain) {
 		struct device_link *link;
 
+		pm_runtime_enable(dev);
+
 		link = device_link_add(data->smicomm_dev, dev,
 				       DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME);
 		if (!link) {
 			dev_err(dev, "Unable link %s.\n", dev_name(data->smicomm_dev));
+			pm_runtime_disable(dev);
 			return -EINVAL;
 		}
 	}
@@ -752,8 +766,10 @@ static int mtk_iommu_probe(struct platform_device *pdev)
 
 	return component_master_add_with_match(dev, &mtk_iommu_com_ops, match);
 out:
-	if (dev->pm_domain)
+	if (dev->pm_domain) {
 		device_link_remove(data->smicomm_dev, dev);
+		pm_runtime_disable(dev);
+	}
 	return ret;
 }
 
@@ -768,8 +784,10 @@ static int mtk_iommu_remove(struct platform_device *pdev)
 		bus_set_iommu(&platform_bus_type, NULL);
 
 	clk_disable_unprepare(data->bclk);
-	if (pdev->dev.pm_domain)
+	if (pdev->dev.pm_domain) {
 		device_link_remove(data->smicomm_dev, &pdev->dev);
+		pm_runtime_disable(&pdev->dev);
+	}
 	devm_free_irq(&pdev->dev, data->irq, data);
 	component_master_del(&pdev->dev, &mtk_iommu_com_ops);
 	return 0;
@@ -801,6 +819,9 @@ static int __maybe_unused mtk_iommu_resume(struct device *dev)
 	void __iomem *base = data->base;
 	int ret;
 
+	/* Avoid first resume to affect the default value of registers below. */
+	if (!m4u_dom)
+		return 0;
 	ret = clk_prepare_enable(data->bclk);
 	if (ret) {
 		dev_err(data->dev, "Failed to enable clk(%d) in resume\n", ret);
@@ -814,13 +835,13 @@ static int __maybe_unused mtk_iommu_resume(struct device *dev)
 	writel_relaxed(reg->int_main_control, base + REG_MMU_INT_MAIN_CONTROL);
 	writel_relaxed(reg->ivrp_paddr, base + REG_MMU_IVRP_PADDR);
 	writel_relaxed(reg->vld_pa_rng, base + REG_MMU_VLD_PA_RNG);
-	if (m4u_dom)
-		writel(m4u_dom->cfg.arm_v7s_cfg.ttbr & MMU_PT_ADDR_MASK,
-		       base + REG_MMU_PT_BASE_ADDR);
+	writel(m4u_dom->cfg.arm_v7s_cfg.ttbr & MMU_PT_ADDR_MASK,
+	       base + REG_MMU_PT_BASE_ADDR);
 	return 0;
 }
 
 static const struct dev_pm_ops mtk_iommu_pm_ops = {
+	SET_RUNTIME_PM_OPS(mtk_iommu_suspend, mtk_iommu_resume, NULL)
 	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mtk_iommu_suspend, mtk_iommu_resume)
 };
 
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#21 lore raw

PATCH v2 15/23 iommu/mediatek: Add iova reserved function

In reply to Yong Wu

For multiple iommu_domains, we need to reserve some iova regions. Take a example, If the default iova region is 0 ~ 4G, but the 0x4000_0000 ~ 0x43ff_ffff is only for the special CCU0 domain. Thus we should exclude this region for the default iova region.

This patch adds iova reserved flow. It's a preparing patch for supporting multi-domain.

---
 drivers/iommu/mtk_iommu.c | 28 ++++++++++++++++++++++++++++
 drivers/iommu/mtk_iommu.h |  5 +++++
 2 files changed, 33 insertions(+)
drivers/iommu/mtk_iommu.c +28 -0
index d22772ec64c8..5b63732044de 100644
@@ -153,6 +153,11 @@ static LIST_HEAD(m4ulist);	/* List all the M4U HWs */
 
 #define for_each_m4u(data)	list_for_each_entry(data, &m4ulist, list)
 
+struct mtk_iommu_iova_region {
+	dma_addr_t		iova_base;
+	unsigned long long	size;
+};
+
 /*
  * There may be 1 or 2 M4U HWs, But we always expect they are in the same domain
  * for the performance.
@@ -539,6 +544,27 @@ static int mtk_iommu_of_xlate(struct device *dev, struct of_phandle_args *args)
 	return iommu_fwspec_add_ids(dev, args->args, 1);
 }
 
+static void mtk_iommu_get_resv_regions(struct device *dev,
+				       struct list_head *head)
+{
+	struct mtk_iommu_data *data = dev_iommu_priv_get(dev);
+	const struct mtk_iommu_iova_region *resv;
+	struct iommu_resv_region *region;
+	int prot = IOMMU_WRITE | IOMMU_READ;
+	unsigned int i;
+
+	for (i = 0; i < data->plat_data->iova_region_nr; i++) {
+		resv = data->plat_data->iova_region + i;
+
+		region = iommu_alloc_resv_region(resv->iova_base, resv->size,
+						 prot, IOMMU_RESV_RESERVED);
+		if (!region)
+			return;
+
+		list_add_tail(&region->list, head);
+	}
+}
+
 static const struct iommu_ops mtk_iommu_ops = {
 	.domain_alloc	= mtk_iommu_domain_alloc,
 	.domain_free	= mtk_iommu_domain_free,
@@ -553,6 +579,8 @@ static const struct iommu_ops mtk_iommu_ops = {
 	.release_device	= mtk_iommu_release_device,
 	.device_group	= mtk_iommu_device_group,
 	.of_xlate	= mtk_iommu_of_xlate,
+	.get_resv_regions = mtk_iommu_get_resv_regions,
+	.put_resv_regions = generic_iommu_put_resv_regions,
 	.pgsize_bitmap	= SZ_4K | SZ_64K | SZ_1M | SZ_16M,
 };
 
drivers/iommu/mtk_iommu.h +5 -0
index ae7909815cdb..d45c13c9d324 100644
@@ -44,10 +44,15 @@ enum mtk_iommu_plat {
 	M4U_MT8183,
 };
 
+struct mtk_iommu_iova_region;
+
 struct mtk_iommu_plat_data {
 	enum mtk_iommu_plat m4u_plat;
 	u32                 flags;
 	u32                 inv_sel_reg;
+
+	unsigned int        iova_region_nr;
+	const struct mtk_iommu_iova_region   *iova_region;
 	unsigned char       larbid_remap[MTK_LARB_COM_MAX][MTK_LARB_SUBCOM_MAX];
 };
 
Signature · 1 line
2.18.0
author maintainer
#22 lore raw

PATCH v2 16/23 iommu/mediatek: Add single domain

In reply to Yong Wu

Defaultly the iova range is 0-4G. here we add a single-domain(0-4G) for the previous SoC. this also is a preparing patch for supporting multi-domains.

---
 drivers/iommu/mtk_iommu.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/iommu/mtk_iommu.c +12 -0
index 5b63732044de..10b9a86ea826 100644
@@ -158,6 +158,10 @@ struct mtk_iommu_iova_region {
 	unsigned long long	size;
 };
 
+static const struct mtk_iommu_iova_region single_domain[] = {
+	{.iova_base = 0,		.size = SZ_4G},
+};
+
 /*
  * There may be 1 or 2 M4U HWs, But we always expect they are in the same domain
  * for the performance.
@@ -877,6 +881,8 @@ static const struct mtk_iommu_plat_data mt2712_data = {
 	.m4u_plat     = M4U_MT2712,
 	.flags        = HAS_4GB_MODE | HAS_BCLK | HAS_VLD_PA_RNG,
 	.inv_sel_reg  = REG_MMU_INV_SEL_GEN1,
+	.iova_region  = single_domain,
+	.iova_region_nr = ARRAY_SIZE(single_domain),
 	.larbid_remap = {{0}, {1}, {2}, {3}, {4}, {5}, {6}, {7}},
 };
 
@@ -884,6 +890,8 @@ static const struct mtk_iommu_plat_data mt6779_data = {
 	.m4u_plat      = M4U_MT6779,
 	.flags         = HAS_SUB_COMM | OUT_ORDER_WR_EN | WR_THROT_EN,
 	.inv_sel_reg   = REG_MMU_INV_SEL_GEN2,
+	.iova_region   = single_domain,
+	.iova_region_nr = ARRAY_SIZE(single_domain),
 	.larbid_remap  = {{0}, {1}, {2}, {3}, {5}, {7, 8}, {10}, {9}},
 };
 
@@ -891,6 +899,8 @@ static const struct mtk_iommu_plat_data mt8173_data = {
 	.m4u_plat     = M4U_MT8173,
 	.flags	      = HAS_4GB_MODE | HAS_BCLK | RESET_AXI,
 	.inv_sel_reg  = REG_MMU_INV_SEL_GEN1,
+	.iova_region  = single_domain,
+	.iova_region_nr = ARRAY_SIZE(single_domain),
 	.larbid_remap = {{0}, {1}, {2}, {3}, {4}, {5}}, /* Linear mapping. */
 };
 
@@ -898,6 +908,8 @@ static const struct mtk_iommu_plat_data mt8183_data = {
 	.m4u_plat     = M4U_MT8183,
 	.flags        = RESET_AXI,
 	.inv_sel_reg  = REG_MMU_INV_SEL_GEN1,
+	.iova_region  = single_domain,
+	.iova_region_nr = ARRAY_SIZE(single_domain),
 	.larbid_remap = {{0}, {4}, {5}, {6}, {7}, {2}, {3}, {1}},
 };
 
Signature · 1 line
2.18.0
author maintainer
#23 lore raw

PATCH v2 17/23 iommu/mediatek: Support master use iova over 32bit

In reply to Yong Wu

After extending v7s, our pagetable already support iova reach 16GB(34bit). the master got the iova via dma_alloc_attrs may reach 34bits, but its HW register still is 32bit. then how to set the bit32/bit33 iova? this depend on a SMI larb setting(bank_sel).

we separate whole 16GB iova to four banks:
bank: 0: 0~4G; 1: 4~8G; 2: 8-12G; 3: 12-16G;
The bank number is (iova >> 32).

We will preassign which bank the larbs belong to. currently we don't have a interface for master to adjust its bank number.

Each a bank is a iova_region which is a independent iommu-domain. the iova range for each iommu-domain can't cross 4G.

---
 drivers/iommu/mtk_iommu.c  | 12 +++++++++---
 drivers/memory/mtk-smi.c   |  7 +++++++
 include/soc/mediatek/smi.h |  1 +
 3 files changed, 17 insertions(+), 3 deletions(-)
drivers/iommu/mtk_iommu.c +9 -3
index 10b9a86ea826..54cad923ae16 100644
@@ -303,17 +303,23 @@ static void mtk_iommu_config(struct mtk_iommu_data *data,
 			     struct device *dev, bool enable)
 {
 	struct mtk_smi_larb_iommu    *larb_mmu;
-	unsigned int                 larbid, portid;
+	unsigned int                 larbid, portid, domid;
 	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
+	const struct mtk_iommu_iova_region *region;
 	int i;
 
 	for (i = 0; i < fwspec->num_ids; ++i) {
 		larbid = MTK_M4U_TO_LARB(fwspec->ids[i]);
 		portid = MTK_M4U_TO_PORT(fwspec->ids[i]);
+		domid = MTK_M4U_TO_DOM(fwspec->ids[i]);
+
 		larb_mmu = &data->larb_imu[larbid];
+		region = data->plat_data->iova_region + domid;
+		larb_mmu->bank[portid] = upper_32_bits(region->iova_base);
 
-		dev_dbg(dev, "%s iommu port: %d\n",
-			enable ? "enable" : "disable", portid);
+		dev_dbg(dev, "%s iommu for larb(%s) port %d dom %d bank %d.\n",
+			enable ? "enable" : "disable", dev_name(larb_mmu->dev),
+			portid, domid, larb_mmu->bank[portid]);
 
 		if (enable)
 			larb_mmu->mmu |= MTK_SMI_MMU_EN(portid);
drivers/memory/mtk-smi.c +7 -0
index ec83f1ac48b1..e94c99ca2883 100644
@@ -41,6 +41,10 @@
 /* mt2712 */
 #define SMI_LARB_NONSEC_CON(id)	(0x380 + ((id) * 4))
 #define F_MMU_EN		BIT(0)
+#define BANK_SEL(id)		({			\
+	u32 _id = (id) & 0x3;				\
+	(_id << 8 | _id << 10 | _id << 12 | _id << 14);	\
+})
 
 /* SMI COMMON */
 #define SMI_BUS_SEL			0x220
@@ -85,6 +89,7 @@ struct mtk_smi_larb { /* larb: local arbiter */
 	const struct mtk_smi_larb_gen	*larb_gen;
 	int				larbid;
 	u32				*mmu;
+	unsigned char			*bank;
 };
 
 static int mtk_smi_clk_enable(const struct mtk_smi *smi)
@@ -151,6 +156,7 @@ mtk_smi_larb_bind(struct device *dev, struct device *master, void *data)
 		if (dev == larb_mmu[i].dev) {
 			larb->larbid = i;
 			larb->mmu = &larb_mmu[i].mmu;
+			larb->bank = larb_mmu[i].bank;
 			return 0;
 		}
 	}
@@ -169,6 +175,7 @@ static void mtk_smi_larb_config_port_gen2_general(struct device *dev)
 	for_each_set_bit(i, (unsigned long *)larb->mmu, 32) {
 		reg = readl_relaxed(larb->base + SMI_LARB_NONSEC_CON(i));
 		reg |= F_MMU_EN;
+		reg |= BANK_SEL(larb->bank[i]);
 		writel(reg, larb->base + SMI_LARB_NONSEC_CON(i));
 	}
 }
include/soc/mediatek/smi.h +1 -0
index 9371bf572ab8..4cf445dbbdaa 100644
@@ -16,6 +16,7 @@
 struct mtk_smi_larb_iommu {
 	struct device *dev;
 	unsigned int   mmu;
+	unsigned char  bank[32];
 };
 
 /*
Signature · 1 line
2.18.0
author maintainer
#24 lore raw

PATCH v2 18/23 iommu/mediatek: Support up to 34bit iova in tlb flush

In reply to Yong Wu

If the iova is 34bit, the iova[32][33] is the bit0/1 in the tlb flush register. Add a new macro for this.

there is a minor change unrelated with this patch. it also use the new macro.

---
 drivers/iommu/mtk_iommu.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/iommu/mtk_iommu.c +7 -4
index 54cad923ae16..9fe9a706742c 100644
@@ -125,6 +125,9 @@ static const struct iommu_ops mtk_iommu_ops;
 
 static int mtk_iommu_hw_init(const struct mtk_iommu_data *data);
 
+#define MTK_IOMMU_ADDR(addr) ({unsigned long _addr = addr; \
+			      (lower_32_bits(_addr) | upper_32_bits(_addr)); })
+
 /*
  * In M4U 4GB mode, the physical address is remapped as below:
  *
@@ -213,8 +216,9 @@ static void mtk_iommu_tlb_flush_range_sync(unsigned long iova, size_t size,
 		writel_relaxed(F_INVLD_EN1 | F_INVLD_EN0,
 			       data->base + data->plat_data->inv_sel_reg);
 
-		writel_relaxed(iova, data->base + REG_MMU_INVLD_START_A);
-		writel_relaxed(iova + size - 1,
+		writel_relaxed(MTK_IOMMU_ADDR(iova),
+			       data->base + REG_MMU_INVLD_START_A);
+		writel_relaxed(MTK_IOMMU_ADDR(iova + size - 1),
 			       data->base + REG_MMU_INVLD_END_A);
 		writel_relaxed(F_MMU_INV_RANGE,
 			       data->base + REG_MMU_INVALIDATE);
@@ -634,8 +638,7 @@ static int mtk_iommu_hw_init(const struct mtk_iommu_data *data)
 	if (data->plat_data->m4u_plat == M4U_MT8173)
 		regval = (data->protect_base >> 1) | (data->enable_4GB << 31);
 	else
-		regval = lower_32_bits(data->protect_base) |
-			 upper_32_bits(data->protect_base);
+		regval = MTK_IOMMU_ADDR(data->protect_base);
 	writel_relaxed(regval, data->base + REG_MMU_IVRP_PADDR);
 
 	if (data->enable_4GB &&
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#25 lore raw

PATCH v2 19/23 iommu/mediatek: Support report iova 34bit translation fault in ISR

In reply to Yong Wu

If the iova is over 32bit, the fault status register bit is a little different. Add a flag for the special register bits.

---
 drivers/iommu/mtk_iommu.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)
drivers/iommu/mtk_iommu.c +16 -2
index 9fe9a706742c..4da92e5739f3 100644
@@ -4,6 +4,7 @@
  * Author: Yong Wu <[email protected]>
  */
 #include <linux/memblock.h>
+#include <linux/bitfield.h>
 #include <linux/bug.h>
 #include <linux/clk.h>
 #include <linux/component.h>
@@ -87,6 +88,9 @@
 #define F_REG_MMU1_FAULT_MASK			GENMASK(13, 7)
 
 #define REG_MMU0_FAULT_VA			0x13c
+#define F_MMU_INVAL_VA_31_12_MASK		GENMASK(31, 12)
+#define F_MMU_INVAL_VA_34_32_MASK		GENMASK(11, 9)
+#define F_MMU_INVAL_PA_34_32_MASK		GENMASK(8, 6)
 #define F_MMU_FAULT_VA_WRITE_BIT		BIT(1)
 #define F_MMU_FAULT_VA_LAYER_BIT		BIT(0)
 
@@ -110,6 +114,7 @@
 #define OUT_ORDER_WR_EN			BIT(4)
 #define HAS_SUB_COMM			BIT(5)
 #define WR_THROT_EN			BIT(6)
+#define IOVA_34_EN			BIT(7)
 
 #define MTK_IOMMU_HAS_FLAG(pdata, _x) \
 		((((pdata)->flags) & (_x)) == (_x))
@@ -258,8 +263,9 @@ static irqreturn_t mtk_iommu_isr(int irq, void *dev_id)
 {
 	struct mtk_iommu_data *data = dev_id;
 	struct mtk_iommu_domain *dom = data->m4u_dom;
-	u32 int_state, regval, fault_iova, fault_pa;
 	unsigned int fault_larb, fault_port, sub_comm = 0;
+	u32 int_state, regval, va34_32, pa34_32;
+	u64 fault_iova, fault_pa;
 	bool layer, write;
 
 	/* Read error info from registers */
@@ -275,6 +281,14 @@ static irqreturn_t mtk_iommu_isr(int irq, void *dev_id)
 	}
 	layer = fault_iova & F_MMU_FAULT_VA_LAYER_BIT;
 	write = fault_iova & F_MMU_FAULT_VA_WRITE_BIT;
+	if (MTK_IOMMU_HAS_FLAG(data->plat_data, IOVA_34_EN)) {
+		va34_32 = FIELD_GET(F_MMU_INVAL_VA_34_32_MASK, fault_iova);
+		pa34_32 = FIELD_GET(F_MMU_INVAL_PA_34_32_MASK, fault_iova);
+		fault_iova = fault_iova & F_MMU_INVAL_VA_31_12_MASK;
+		fault_iova |=  (u64)va34_32 << 32;
+		fault_pa |= (u64)pa34_32 << 32;
+	}
+
 	fault_port = F_MMU_INT_ID_PORT_ID(regval);
 	if (MTK_IOMMU_HAS_FLAG(data->plat_data, HAS_SUB_COMM)) {
 		fault_larb = F_MMU_INT_ID_COMM_ID(regval);
@@ -288,7 +302,7 @@ static irqreturn_t mtk_iommu_isr(int irq, void *dev_id)
 			       write ? IOMMU_FAULT_WRITE : IOMMU_FAULT_READ)) {
 		dev_err_ratelimited(
 			data->dev,
-			"fault type=0x%x iova=0x%x pa=0x%x larb=%d port=%d layer=%d %s\n",
+			"fault type=0x%x iova=0x%llx pa=0x%llx larb=%d port=%d layer=%d %s\n",
 			int_state, fault_iova, fault_pa, fault_larb, fault_port,
 			layer, write ? "write" : "read");
 	}
Signature · 1 line
2.18.0
author maintainer
#26 lore raw

PATCH v2 20/23 iommu/mediatek: Add support for multi domain

In reply to Yong Wu

Some HW IP(ex: CCU) require the special iova range. That means the iova got from dma_alloc_attrs for that devices must locate in his special range. In this patch, we allocate a special iova_range for each a special requirement and create each a iommu domain for each a iova_range.

meanwhile we still use one pagetable which support 16GB iova.

After this patch, If the iova range of a master is over 4G, the master should:
a) Declare its special dma_ranges in its dtsi node. For example, If we preassign the iova 4G-8G for vcodec, then the vcodec dtsi node should add this:
/*
* iova start at 0x1_0000_0000, pa still start at 0x4000_0000
* size is 0x1_0000_0000.
*/
dma-ranges = <0x1 0x0 0x0 0x40000000 0x1 0x0>; /* 4G ~ 8G */
Note: we don't have a actual bus concept here. the master doesn't have its special parent node, thus this dma-ranges can only be put in the master's node.

b) Update the dma_mask:
dma_set_mask_and_coherent(dev, DMA_BIT_MASK(33));

---
 drivers/iommu/mtk_iommu.c | 47 +++++++++++++++++++++++++++++++--------
 drivers/iommu/mtk_iommu.h |  3 ++-
 2 files changed, 40 insertions(+), 10 deletions(-)
drivers/iommu/mtk_iommu.c +38 -9
index 4da92e5739f3..93ce4fa806cf 100644
@@ -350,6 +350,14 @@ static int mtk_iommu_domain_finalise(struct mtk_iommu_domain *dom)
 {
 	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
 
+	/* Use the exist domain as there is only one m4u pgtable here. */
+	if (data->m4u_dom) {
+		dom->iop = data->m4u_dom->iop;
+		dom->cfg = data->m4u_dom->cfg;
+		dom->domain.pgsize_bitmap = data->m4u_dom->cfg.pgsize_bitmap;
+		return 0;
+	}
+
 	dom->cfg = (struct io_pgtable_cfg) {
 		.quirks = IO_PGTABLE_QUIRK_ARM_NS |
 			IO_PGTABLE_QUIRK_NO_PERMS |
@@ -375,6 +383,8 @@ static int mtk_iommu_domain_finalise(struct mtk_iommu_domain *dom)
 
 static struct iommu_domain *mtk_iommu_domain_alloc(unsigned type)
 {
+	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
+	const struct mtk_iommu_iova_region *region;
 	struct mtk_iommu_domain *dom;
 
 	if (type != IOMMU_DOMAIN_DMA)
@@ -390,8 +400,9 @@ static struct iommu_domain *mtk_iommu_domain_alloc(unsigned type)
 	if (mtk_iommu_domain_finalise(dom))
 		goto  put_dma_cookie;
 
-	dom->domain.geometry.aperture_start = 0;
-	dom->domain.geometry.aperture_end = DMA_BIT_MASK(32);
+	region = data->plat_data->iova_region + data->cur_domid;
+	dom->domain.geometry.aperture_start = region->iova_base;
+	dom->domain.geometry.aperture_end = region->iova_base + region->size - 1;
 	dom->domain.geometry.force_aperture = true;
 
 	return &dom->domain;
@@ -535,19 +546,31 @@ static void mtk_iommu_release_device(struct device *dev)
 static struct iommu_group *mtk_iommu_device_group(struct device *dev)
 {
 	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
+	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
+	struct iommu_group *group;
+	int domid;
 
 	if (!data)
 		return ERR_PTR(-ENODEV);
 
-	/* All the client devices are in the same m4u iommu-group */
-	if (!data->m4u_group) {
-		data->m4u_group = iommu_group_alloc();
-		if (IS_ERR(data->m4u_group))
+	domid = MTK_M4U_TO_DOM(fwspec->ids[0]);
+	if (domid >= data->plat_data->iova_region_nr) {
+		dev_err(dev, "iommu domain id(%d/%d) is error.\n", domid,
+			data->plat_data->iova_region_nr);
+		return ERR_PTR(-EINVAL);
+	}
+
+	group = data->m4u_group[domid];
+	if (!group) {
+		group = iommu_group_alloc();
+		if (IS_ERR(group))
 			dev_err(dev, "Failed to allocate M4U IOMMU group\n");
+		data->m4u_group[domid] = group;
 	} else {
-		iommu_group_ref_get(data->m4u_group);
+		iommu_group_ref_get(group);
 	}
-	return data->m4u_group;
+	data->cur_domid = domid;
+	return group;
 }
 
 static int mtk_iommu_of_xlate(struct device *dev, struct of_phandle_args *args)
@@ -576,14 +599,20 @@ static void mtk_iommu_get_resv_regions(struct device *dev,
 				       struct list_head *head)
 {
 	struct mtk_iommu_data *data = dev_iommu_priv_get(dev);
-	const struct mtk_iommu_iova_region *resv;
+	const struct mtk_iommu_iova_region *resv, *curdom;
 	struct iommu_resv_region *region;
 	int prot = IOMMU_WRITE | IOMMU_READ;
 	unsigned int i;
 
+	curdom = data->plat_data->iova_region + data->cur_domid;
 	for (i = 0; i < data->plat_data->iova_region_nr; i++) {
 		resv = data->plat_data->iova_region + i;
 
+		/* Only reserve when the region is in the current domain */
+		if (resv->iova_base <= curdom->iova_base ||
+		    resv->iova_base + resv->size >= curdom->iova_base + curdom->size)
+			continue;
+
 		region = iommu_alloc_resv_region(resv->iova_base, resv->size,
 						 prot, IOMMU_RESV_RESERVED);
 		if (!region)
drivers/iommu/mtk_iommu.h +2 -1
index d45c13c9d324..5e346464cdf8 100644
@@ -66,7 +66,7 @@ struct mtk_iommu_data {
 	phys_addr_t			protect_base; /* protect memory base */
 	struct mtk_iommu_suspend_reg	reg;
 	struct mtk_iommu_domain		*m4u_dom;
-	struct iommu_group		*m4u_group;
+	struct iommu_group		*m4u_group[MTK_M4U_DOM_NR_MAX];
 	bool                            enable_4GB;
 	spinlock_t			tlb_lock; /* lock for tlb range flush */
 
@@ -76,6 +76,7 @@ struct mtk_iommu_data {
 
 	struct dma_iommu_mapping	*mapping; /* For mtk_iommu_v1.c */
 
+	unsigned int			cur_domid;
 	struct list_head		list;
 	struct mtk_smi_larb_iommu	larb_imu[MTK_LARB_NR_MAX];
 };
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#27 lore raw

PATCH v2 21/23 iommu/mediatek: Adjust the structure

In reply to Yong Wu

Add "struct mtk_iommu_data *" in the "struct mtk_iommu_domain", reduce the call mtk_iommu_get_m4u_data().
No functional change.

---
 drivers/iommu/mtk_iommu.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)
drivers/iommu/mtk_iommu.c +10 -8
index 93ce4fa806cf..d0593d317240 100644
@@ -123,6 +123,7 @@ struct mtk_iommu_domain {
 	struct io_pgtable_cfg		cfg;
 	struct io_pgtable_ops		*iop;
 
+	struct mtk_iommu_data		*data;
 	struct iommu_domain		domain;
 };
 
@@ -348,7 +349,7 @@ static void mtk_iommu_config(struct mtk_iommu_data *data,
 
 static int mtk_iommu_domain_finalise(struct mtk_iommu_domain *dom)
 {
-	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
+	struct mtk_iommu_data *data = dom->data;
 
 	/* Use the exist domain as there is only one m4u pgtable here. */
 	if (data->m4u_dom) {
@@ -397,6 +398,7 @@ static struct iommu_domain *mtk_iommu_domain_alloc(unsigned type)
 	if (iommu_get_dma_cookie(&dom->domain))
 		goto  free_dom;
 
+	dom->data = data;
 	if (mtk_iommu_domain_finalise(dom))
 		goto  put_dma_cookie;
 
@@ -469,10 +471,9 @@ static int mtk_iommu_map(struct iommu_domain *domain, unsigned long iova,
 			 phys_addr_t paddr, size_t size, int prot, gfp_t gfp)
 {
 	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
-	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
 
 	/* The "4GB mode" M4U physically can not use the lower remap of Dram. */
-	if (data->enable_4GB)
+	if (dom->data->enable_4GB)
 		paddr |= BIT_ULL(32);
 
 	/* Synchronize with the tlb_lock */
@@ -490,31 +491,32 @@ static size_t mtk_iommu_unmap(struct iommu_domain *domain,
 
 static void mtk_iommu_flush_iotlb_all(struct iommu_domain *domain)
 {
-	mtk_iommu_tlb_flush_all(mtk_iommu_get_m4u_data());
+	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
+
+	mtk_iommu_tlb_flush_all(dom->data);
 }
 
 static void mtk_iommu_iotlb_sync(struct iommu_domain *domain,
 				 struct iommu_iotlb_gather *gather)
 {
-	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
+	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
 	size_t length = gather->end - gather->start;
 
 	if (gather->start == ULONG_MAX)
 		return;
 
 	mtk_iommu_tlb_flush_range_sync(gather->start, length, gather->pgsize,
-				       data);
+				       dom->data);
 }
 
 static phys_addr_t mtk_iommu_iova_to_phys(struct iommu_domain *domain,
 					  dma_addr_t iova)
 {
 	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
-	struct mtk_iommu_data *data = mtk_iommu_get_m4u_data();
 	phys_addr_t pa;
 
 	pa = dom->iop->iova_to_phys(dom->iop, iova);
-	if (data->enable_4GB && pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
+	if (dom->data->enable_4GB && pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
 		pa &= ~BIT_ULL(32);
 
 	return pa;
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#28 lore raw

PATCH v2 22/23 iommu/mediatek: Add mt8192 support

In reply to Yong Wu

Add mt8192 iommu support.

For multi domain, Add 1M gap for the vdec domain size. That is because vdec HW has a end address register which require (start_addr + len) rather than (start_addr + len - 1). Take a example, if the start_addr is 0xfff00000, size is 0x100000, then the end_address is 0xfff00000 + 0x100000 = 0x1 0000 0000. but the register only is 32bit. thus HW will get the end address is 0. To avoid this issue, I add 1M gap for this.

---
 drivers/iommu/mtk_iommu.c | 22 ++++++++++++++++++++++
 drivers/iommu/mtk_iommu.h |  1 +
 2 files changed, 23 insertions(+)
drivers/iommu/mtk_iommu.c +22 -0
index d0593d317240..ebc3767b62ab 100644
@@ -171,6 +171,16 @@ static const struct mtk_iommu_iova_region single_domain[] = {
 	{.iova_base = 0,		.size = SZ_4G},
 };
 
+static const struct mtk_iommu_iova_region mt8192_multi_dom[] = {
+	{ .iova_base = 0x0,		.size = SZ_4G},		/* disp: 0 ~ 4G */
+	#if IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT)
+	{ .iova_base = SZ_4G,		.size = SZ_4G - SZ_1M},	/* vdec: 4G ~ 8G gap: 1M */
+	{ .iova_base = SZ_4G * 2,	.size = SZ_4G - SZ_1M},	/* CAM/MDP: 8G ~ 12G */
+	{ .iova_base = 0x240000000ULL,	.size = 0x4000000},	/* CCU0 */
+	{ .iova_base = 0x244000000ULL,	.size = 0x4000000},	/* CCU1 */
+	#endif
+};
+
 /*
  * There may be 1 or 2 M4U HWs, But we always expect they are in the same domain
  * for the performance.
@@ -967,11 +977,23 @@ static const struct mtk_iommu_plat_data mt8183_data = {
 	.larbid_remap = {{0}, {4}, {5}, {6}, {7}, {2}, {3}, {1}},
 };
 
+static const struct mtk_iommu_plat_data mt8192_data = {
+	.m4u_plat       = M4U_MT8192,
+	.flags          = HAS_BCLK | HAS_SUB_COMM | OUT_ORDER_WR_EN |
+			  WR_THROT_EN | IOVA_34_EN,
+	.inv_sel_reg    = REG_MMU_INV_SEL_GEN2,
+	.iova_region    = mt8192_multi_dom,
+	.iova_region_nr = ARRAY_SIZE(mt8192_multi_dom),
+	.larbid_remap   = {{0}, {1}, {4, 5}, {7}, {2}, {9, 11, 19, 20},
+			   {0, 14, 16}, {0, 13, 18, 17}},
+};
+
 static const struct of_device_id mtk_iommu_of_ids[] = {
 	{ .compatible = "mediatek,mt2712-m4u", .data = &mt2712_data},
 	{ .compatible = "mediatek,mt6779-m4u", .data = &mt6779_data},
 	{ .compatible = "mediatek,mt8173-m4u", .data = &mt8173_data},
 	{ .compatible = "mediatek,mt8183-m4u", .data = &mt8183_data},
+	{ .compatible = "mediatek,mt8192-m4u", .data = &mt8192_data},
 	{}
 };
 
drivers/iommu/mtk_iommu.h +1 -0
index 5e346464cdf8..d2702eda25d4 100644
@@ -42,6 +42,7 @@ enum mtk_iommu_plat {
 	M4U_MT6779,
 	M4U_MT8173,
 	M4U_MT8183,
+	M4U_MT8192,
 };
 
 struct mtk_iommu_iova_region;
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#29 lore raw

PATCH v2 23/23 memory: mtk-smi: Add mt8192 support

In reply to Yong Wu

Add mt8192 smi support.

---
 drivers/memory/mtk-smi.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
drivers/memory/mtk-smi.c +19 -0
index e94c99ca2883..0ec3eff4d92d 100644
@@ -261,6 +261,10 @@ static const struct mtk_smi_larb_gen mtk_smi_larb_mt8183 = {
 				      /* IPU0 | IPU1 | CCU */
 };
 
+static const struct mtk_smi_larb_gen mtk_smi_larb_mt8192 = {
+	.config_port                = mtk_smi_larb_config_port_gen2_general,
+};
+
 static const struct of_device_id mtk_smi_larb_of_ids[] = {
 	{
 		.compatible = "mediatek,mt8173-smi-larb",
@@ -282,6 +286,10 @@ static const struct of_device_id mtk_smi_larb_of_ids[] = {
 		.compatible = "mediatek,mt8183-smi-larb",
 		.data = &mtk_smi_larb_mt8183
 	},
+	{
+		.compatible = "mediatek,mt8192-smi-larb",
+		.data = &mtk_smi_larb_mt8192
+	},
 	{}
 };
 
@@ -421,6 +429,13 @@ static const struct mtk_smi_common_plat mtk_smi_common_mt8183 = {
 		    F_MMU1_LARB(7),
 };
 
+static const struct mtk_smi_common_plat mtk_smi_common_mt8192 = {
+	.gen      = MTK_SMI_GEN2,
+	.has_gals = true,
+	.bus_sel  = F_MMU1_LARB(1) | F_MMU1_LARB(2) | F_MMU1_LARB(5) |
+		    F_MMU1_LARB(6),
+};
+
 static const struct of_device_id mtk_smi_common_of_ids[] = {
 	{
 		.compatible = "mediatek,mt8173-smi-common",
@@ -442,6 +457,10 @@ static const struct of_device_id mtk_smi_common_of_ids[] = {
 		.compatible = "mediatek,mt8183-smi-common",
 		.data = &mtk_smi_common_mt8183,
 	},
+	{
+		.compatible = "mediatek,mt8192-smi-common",
+		.data = &mtk_smi_common_mt8192,
+	},
 	{}
 };
 
Signature · 5 lines
2.18.0
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu