Skip to contentSkip to conversation

dt-bindings: arm: fsl: Add binding for Gateworks boards with IMX8MM

PATCH Applied Tim Harvey 3 participants 4 messages Jan 4, 2021 – Jan 11, 2021

Subsystems (2)
lore
Share & tools
lore

Tim Harvey

author
#0 lore raw

PATCH v5 1/2 dt-bindings: arm: fsl: Add binding for Gateworks boards with IMX8MM

Add bindings for the Gateworks Venice Development kit boards with IMX8MM System on Module.

---
v5: no changes
v4: no changes
v3: no changes
v2: no changes

---
 Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +3 -0
index 1ca9dfa..705c6e8 100644
@@ -405,6 +405,9 @@ properties:
               - beacon,imx8mm-beacon-kit  # i.MX8MM Beacon Development Kit
               - fsl,imx8mm-ddr4-evk       # i.MX8MM DDR4 EVK Board
               - fsl,imx8mm-evk            # i.MX8MM EVK Board
+              - gw,imx8mm-gw71xx-0x       # i.MX8MM Gateworks Development Kit
+              - gw,imx8mm-gw72xx-0x       # i.MX8MM Gateworks Development Kit
+              - gw,imx8mm-gw73xx-0x       # i.MX8MM Gateworks Development Kit
               - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
Signature · 1 line
2.7.4
author
#1 lore raw

PATCH v5 2/2 arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits

The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development kits consisting of a GW700x SoM and a Baseboard. Future SoM's such as the GW701x will create additional combinations.

The GW700x SoM contains:
- i.MX 8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor)
- GbE PHY connected to the i.MX 8M Mini FEC
- Power Management IC

The GW71xx Baseboard contains:
- 1x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 1x RJ45 GbE (i.MX 8M Mini FEC)
- I/O connector with 1x-SPI/1x-I2C/1x-UART/4x-GPIO signals
- PCIe Clock generator
- GPS and accelerometer
- 1x USB 2.0 Front Panel connector
- wide range power supply

The GW72xx Baseboard contains:
- 2x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x)
- 1x MicroSD connector
- 1x USB 2.0 Front Panel connector
- 1x SPI connector
- 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of:
RS232 w/ flow-control, RS485, RS422
- PCIe Clock generator
- GPS and accelerometer
- Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
- I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C
- wide range power supply

The GW73xx Baseboard contains:
- 3x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x)
- 1x MicroSD connector
- 1x USB 2.0 Front Panel connector
- 1x SPI connector
- 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of:
RS232 w/ flow-control, RS485, RS422
- WiFi/BT
- PCIe Clock generator
- GPS and accelerometer
- Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
- I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C
- wide range power supply

---
v5:
- fixed typo/grammar in commit log (s/controll/control s/comprised/consisting/)
- removed underscore from remaining node names
- removed blank line in hoggrp
- removed unused assigned-clocks and assigned-clock-rates node from usdhc nodes

v4:
- replace underscore with hyphen for gpio-keys node
- add 'off-board header' comments to i2c/spi/uart nodes that go off-board
- move node comments to own line above node
- add spaces after comma
- move uart2_gpio rs485 config pinmux to hoggroup as they don't necessarily relate to uart2
- fix fifo-depth dt property for phy

v3:
- fix gpio controller node name
- add rtc node to SoM
- add pmic pinctrl to SoM
- fixed compatible string for SoM eeprom's

v2:
- fix i.MX 8M Mini name in commit log
- consistent use of underscore vs hyphen in labels
- fix gsc interrupt type
- fix iomux group node names
- fix led-controller bindings:
(use correct node names, color, function and remove label)
- use accelerometer node name vs accel
- remove sai3 from gw71xx baseboard
- added serial connector description to commit message
- added I/O connector description to commit message
- removed unnecessary #address-cells/#size-cells from gpio-keys node

---
 arch/arm64/boot/dts/freescale/Makefile             |   3 +
 .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi   | 495 +++++++++++++++++++++
 .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts |  19 +
 .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi   | 186 ++++++++
 .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts |  20 +
 .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi   | 311 +++++++++++++
 .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts |  19 +
 .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi   | 362 +++++++++++++++
 8 files changed, 1415 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
arch/arm64/boot/dts/freescale/Makefile +3 -0
index f8d5943..ecdd233 100644
@@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi new file +495 -0

495 lines not on this page · raw message

arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts new file +19 -0
new file mode 100644
index 00000000..3f88c4a
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2020 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+#include "imx8mm-venice-gw700x.dtsi"
+#include "imx8mm-venice-gw71xx.dtsi"
+
+/ {
+	model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit";
+	compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi new file +186 -0

186 lines not on this page · raw message

arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts new file +20 -0
new file mode 100644
index 00000000..b1e7540
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2020 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+#include "imx8mm-venice-gw700x.dtsi"
+#include "imx8mm-venice-gw72xx.dtsi"
+
+/ {
+	model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit";
+	compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi new file +311 -0

311 lines not on this page · raw message

arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts new file +19 -0
new file mode 100644
index 00000000..6905437
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2020 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+#include "imx8mm-venice-gw700x.dtsi"
+#include "imx8mm-venice-gw73xx.dtsi"
+
+/ {
+	model = "Gateworks Venice GW73xx-0x i.MX8MM Development Kit";
+	compatible = "gw,imx8mm-gw73xx-0x", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi new file +362 -0

362 lines not on this page · raw message

Signature · 1 line
2.7.4
Reviewed-by on v5 2/2
#2 lore raw

Re: [PATCH v5 2/2] arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits

Quoted 50 lines · Tim Harvey

The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development kits consisting of a GW700x SoM and a Baseboard. Future SoM's such as the GW701x will create additional combinations.

The GW700x SoM contains:
- i.MX 8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor)
- GbE PHY connected to the i.MX 8M Mini FEC
- Power Management IC

The GW71xx Baseboard contains:
- 1x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 1x RJ45 GbE (i.MX 8M Mini FEC)
- I/O connector with 1x-SPI/1x-I2C/1x-UART/4x-GPIO signals
- PCIe Clock generator
- GPS and accelerometer
- 1x USB 2.0 Front Panel connector
- wide range power supply

The GW72xx Baseboard contains:
- 2x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x)
- 1x MicroSD connector
- 1x USB 2.0 Front Panel connector
- 1x SPI connector
- 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of:

   RS232 w/ flow-control, RS485, RS422

- PCIe Clock generator
- GPS and accelerometer
- Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
- I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C
- wide range power supply

The GW73xx Baseboard contains:
- 3x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x)
- 1x MicroSD connector
- 1x USB 2.0 Front Panel connector
- 1x SPI connector
- 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of:

   RS232 w/ flow-control, RS485, RS422

- WiFi/BT
- PCIe Clock generator
- GPS and accelerometer
- Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
- I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C
- wide range power supply

Quoted 8 lines

---
v5:
- fixed typo/grammar in commit log (s/controll/control s/comprised/consisting/)
- removed underscore from remaining node names
- removed blank line in hoggrp
- removed unused assigned-clocks and assigned-clock-rates node from usdhc nodes

Best regards,
Krzysztof