Fix serial number usage in MHI bus
Subsystems (2)
v2 cover Fix serial number usage in MHI bus
In some cases, device may boot straight to the mission mode. The serial number and OEM PK hash values would remain unpopulated in those cases. Hence, move the reads for those to the power up preparation phase such that controllers always have them populated. Also, in order to maintain consistency with the way OEM PK hash is displayed and improve the current way, depict serial number in hexadecimals.
Tested on: X86_64 architecture with SDX65 on Ubuntu 18.04 distribution.
v2:
-Fixed nitpick for 0x%x
-Minor update to commit message for "Depict serial number" patch -Added reviewed-by tags
Bhaumik Bhatt (2):
bus: mhi: core: Move serial number read to power up phase
bus: mhi: core: Depict serial number in hexadecimals
drivers/bus/mhi/core/boot.c | 17 +---------------- drivers/bus/mhi/core/init.c | 19 +++++++++++++++++-- 2 files changed, 18 insertions(+), 18 deletions(-)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v2 1/2 bus: mhi: core: Move serial number read to power up phase
In some cases device may boot straight to ready and move to AMSS execution environment. Serial number and OEM PK Hash values would remain unpopulated in those scenarios. Move the reads for those power up preparation phase for controllers to always have them populated.
--- drivers/bus/mhi/core/boot.c | 17 +---------------- drivers/bus/mhi/core/init.c | 17 ++++++++++++++++- 2 files changed, 17 insertions(+), 17 deletions(-)
drivers/bus/mhi/core/boot.c +1 -16
@@ -394,28 +394,13 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)void *buf;dma_addr_t dma_addr;size_t size; -int i, ret; +int ret;if (MHI_PM_IN_ERROR_STATE (mhi_cntrl->pm_state)) {dev_err (dev,"Device MHI is not in valid state\n" );return ; } -/* save hardware info from BHI */ - ret =mhi_read_reg (mhi_cntrl, mhi_cntrl->bhi,BHI_SERIALNU , - &mhi_cntrl->serial_number); -if (ret) -dev_err (dev,"Could not capture serial number via BHI\n" ); - -for (i =0 ; i <ARRAY_SIZE (mhi_cntrl->oem_pk_hash); i++) { - ret =mhi_read_reg (mhi_cntrl, mhi_cntrl->bhi,BHI_OEMPKHASH (i), - &mhi_cntrl->oem_pk_hash[i]); -if (ret) { -dev_err (dev,"Could not capture OEM PK HASH via BHI\n" ); -break ; - } - } -/* wait for ready on pass through or any other execution environment */ if (mhi_cntrl->ee !=MHI_EE_EDL && mhi_cntrl->ee !=MHI_EE_PBL ) goto fw_load_ready_state;
drivers/bus/mhi/core/init.c +16 -1
@@ -1065,7 +1065,7 @@ int mhi_prepare_for_power_up(struct mhi_controller *mhi_cntrl) {struct device *dev = &mhi_cntrl->mhi_dev->dev;u32 bhi_off, bhie_off; -int ret; +int i, ret;mutex_lock (&mhi_cntrl->pm_mutex);
@@ -1124,6 +1124,21 @@ int mhi_prepare_for_power_up(struct mhi_controller *mhi_cntrl)mutex_unlock (&mhi_cntrl->pm_mutex); +/* save hardware info from BHI */ + ret =mhi_read_reg (mhi_cntrl, mhi_cntrl->bhi,BHI_SERIALNU , + &mhi_cntrl->serial_number); +if (ret) +dev_err (dev,"Could not capture serial number via BHI\n" ); + +for (i =0 ; i <ARRAY_SIZE (mhi_cntrl->oem_pk_hash); i++) { + ret =mhi_read_reg (mhi_cntrl, mhi_cntrl->bhi,BHI_OEMPKHASH (i), + &mhi_cntrl->oem_pk_hash[i]); +if (ret) { +dev_err (dev,"Could not capture OEM PK HASH via BHI\n" ); +break ; + } + } +return 0 ; error_reg_offset:
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH v2 1/2] bus: mhi: core: Move serial number read to power up phase
Quoted 8 lines · Bhaumik Bhatt
In some cases device may boot straight to ready and move to AMSS execution environment. Serial number and OEM PK Hash values would remain unpopulated in those scenarios. Move the reads for those power up preparation phase for controllers to always have them populated.
Signed-off-by Bhaumik Bhatt <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>
Signature · 1 line
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v2 2/2 bus: mhi: core: Depict serial number in hexadecimals
In reply to Bhaumik BhattIn order to better reflect usage of serial number, it is prudent to depict it in hexadecimals.
--- drivers/bus/mhi/core/init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/bus/mhi/core/init.c +1 -1
@@ -94,7 +94,7 @@ static ssize_t serial_number_show(struct device *dev,struct mhi_device *mhi_dev =to_mhi_device (dev);struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl; -return snprintf (buf,PAGE_SIZE ,"Serial Number: %u\n" , +return snprintf (buf,PAGE_SIZE ,"Serial Number: 0x%x\n" , mhi_cntrl->serial_number); }static DEVICE_ATTR_RO (serial_number);
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH v2 2/2] bus: mhi: core: Depict serial number in hexadecimals
Quoted 5 lines · Bhaumik Bhatt
In order to better reflect usage of serial number, it is prudent to depict it in hexadecimals.
Signed-off-by Bhaumik Bhatt <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>
Signature · 1 line
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project