Skip to contentSkip to conversation

Fix serial number usage in MHI bus

PATCH In review Bhaumik Bhatt 2 participants 5 messages Jul 29, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v2 cover Fix serial number usage in MHI bus

In some cases, device may boot straight to the mission mode. The serial number and OEM PK hash values would remain unpopulated in those cases. Hence, move the reads for those to the power up preparation phase such that controllers always have them populated. Also, in order to maintain consistency with the way OEM PK hash is displayed and improve the current way, depict serial number in hexadecimals.

Tested on: X86_64 architecture with SDX65 on Ubuntu 18.04 distribution.

v2:
-Fixed nitpick for 0x%x
-Minor update to commit message for "Depict serial number" patch -Added reviewed-by tags

Bhaumik Bhatt (2):
bus: mhi: core: Move serial number read to power up phase
bus: mhi: core: Depict serial number in hexadecimals

 drivers/bus/mhi/core/boot.c | 17 +----------------
 drivers/bus/mhi/core/init.c | 19 +++++++++++++++++--
 2 files changed, 18 insertions(+), 18 deletions(-)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
#1 lore raw

PATCH v2 1/2 bus: mhi: core: Move serial number read to power up phase

In some cases device may boot straight to ready and move to AMSS execution environment. Serial number and OEM PK Hash values would remain unpopulated in those scenarios. Move the reads for those power up preparation phase for controllers to always have them populated.

---
 drivers/bus/mhi/core/boot.c | 17 +----------------
 drivers/bus/mhi/core/init.c | 17 ++++++++++++++++-
 2 files changed, 17 insertions(+), 17 deletions(-)
drivers/bus/mhi/core/boot.c +1 -16
index 0a97262..e13d34c 100644
@@ -394,28 +394,13 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
 	void *buf;
 	dma_addr_t dma_addr;
 	size_t size;
-	int i, ret;
+	int ret;
 
 	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
 		dev_err(dev, "Device MHI is not in valid state\n");
 		return;
 	}
 
-	/* save hardware info from BHI */
-	ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_SERIALNU,
-			   &mhi_cntrl->serial_number);
-	if (ret)
-		dev_err(dev, "Could not capture serial number via BHI\n");
-
-	for (i = 0; i < ARRAY_SIZE(mhi_cntrl->oem_pk_hash); i++) {
-		ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_OEMPKHASH(i),
-				   &mhi_cntrl->oem_pk_hash[i]);
-		if (ret) {
-			dev_err(dev, "Could not capture OEM PK HASH via BHI\n");
-			break;
-		}
-	}
-
 	/* wait for ready on pass through or any other execution environment */
 	if (mhi_cntrl->ee != MHI_EE_EDL && mhi_cntrl->ee != MHI_EE_PBL)
 		goto fw_load_ready_state;
drivers/bus/mhi/core/init.c +16 -1
index 5aaca6d..d98a14b 100644
@@ -1065,7 +1065,7 @@ int mhi_prepare_for_power_up(struct mhi_controller *mhi_cntrl)
 {
 	struct device *dev = &mhi_cntrl->mhi_dev->dev;
 	u32 bhi_off, bhie_off;
-	int ret;
+	int i, ret;
 
 	mutex_lock(&mhi_cntrl->pm_mutex);
 
@@ -1124,6 +1124,21 @@ int mhi_prepare_for_power_up(struct mhi_controller *mhi_cntrl)
 
 	mutex_unlock(&mhi_cntrl->pm_mutex);
 
+	/* save hardware info from BHI */
+	ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_SERIALNU,
+			   &mhi_cntrl->serial_number);
+	if (ret)
+		dev_err(dev, "Could not capture serial number via BHI\n");
+
+	for (i = 0; i < ARRAY_SIZE(mhi_cntrl->oem_pk_hash); i++) {
+		ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_OEMPKHASH(i),
+				   &mhi_cntrl->oem_pk_hash[i]);
+		if (ret) {
+			dev_err(dev, "Could not capture OEM PK HASH via BHI\n");
+			break;
+		}
+	}
+
 	return 0;
 
 error_reg_offset:
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Reviewed-by on v2 1/2
#2 lore raw

Re: [PATCH v2 1/2] bus: mhi: core: Move serial number read to power up phase

Quoted 8 lines · Bhaumik Bhatt

In some cases device may boot straight to ready and move to AMSS execution environment. Serial number and OEM PK Hash values would remain unpopulated in those scenarios. Move the reads for those power up preparation phase for controllers to always have them populated.

Signature · 1 line
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
#3 lore raw

PATCH v2 2/2 bus: mhi: core: Depict serial number in hexadecimals

In reply to Bhaumik Bhatt

In order to better reflect usage of serial number, it is prudent to depict it in hexadecimals.

---
 drivers/bus/mhi/core/init.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/bus/mhi/core/init.c +1 -1
index d98a14b..7ea1f01 100644
@@ -94,7 +94,7 @@ static ssize_t serial_number_show(struct device *dev,
 	struct mhi_device *mhi_dev = to_mhi_device(dev);
 	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
 
-	return snprintf(buf, PAGE_SIZE, "Serial Number: %u\n",
+	return snprintf(buf, PAGE_SIZE, "Serial Number: 0x%x\n",
 			mhi_cntrl->serial_number);
 }
 static DEVICE_ATTR_RO(serial_number);
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Reviewed-by on v2 2/2
#4 lore raw

Re: [PATCH v2 2/2] bus: mhi: core: Depict serial number in hexadecimals

Quoted 5 lines · Bhaumik Bhatt

In order to better reflect usage of serial number, it is prudent to depict it in hexadecimals.

Signature · 1 line
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project