Add Vol+ support for sc7280-idp
Subsystems (8)
v4 cover Add Vol+ support for sc7280-idp
David Collins (1):
pinctrl: qcom: spmi-gpio: correct parent irqspec translation
satya priya (1):
arm64: dts: sc7280: Add volume up support for sc7280-idp
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 31 ++++++++++++++++++++++++++ drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 37 +++++++++++++++++++++++++++++--- 2 files changed, 65 insertions(+), 3 deletions(-)
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
PATCH v4 1/2 pinctrl: qcom: spmi-gpio: correct parent irqspec translation
From: David Collins <[email protected]>
pmic_gpio_child_to_parent_hwirq() and gpiochip_populate_parent_fwspec_fourcell() translate a pinctrl- spmi-gpio irqspec to an SPMI controller irqspec. When they do this, they use a fixed SPMI slave ID of 0 and a fixed GPIO peripheral offset of 0xC0 (corresponding to SPMI address 0xC000). This translation results in an incorrect irqspec for secondary PMICs that don't have a slave ID of 0 as well as for PMIC chips which have GPIO peripherals located at a base address other than 0xC000.
Correct this issue by passing the slave ID of the pinctrl-spmi- gpio device's parent in the SPMI controller irqspec and by calculating the peripheral ID base from the device tree 'reg' property of the pinctrl-spmi-gpio device.
---
Changes in V2:
- Added a fixes tag.
Changes in V3:
- Removed "fwspec->param[2] = 0" from pmic_gpio_populate_parent_fwspec, as it is already set to zero, and must be left that way.
Changes in V4:
- No changes.
drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 37 +++++++++++++++++++++++++++++--- 1 file changed, 34 insertions(+), 3 deletions(-)
drivers/pinctrl/qcom/pinctrl-spmi-gpio.c +34 -3
@@ -1,6 +1,6 @@// SPDX-License-Identifier: GPL-2.0-only /* -* Copyright (c) 2012-2014, The Linux Foundation. All rights reserved. +* Copyright (c) 2012-2014, 2016-2021 The Linux Foundation. All rights reserved. */ #include <linux/gpio/driver.h>
@@ -14,6 +14,7 @@#include <linux/platform_device.h> #include <linux/regmap.h> #include <linux/slab.h> +#include <linux/spmi.h> #include <linux/types.h> #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
@@ -171,6 +172,8 @@ struct pmic_gpio_state {struct pinctrl_dev *ctrl;struct gpio_chip chip;struct irq_chip irq; +u8 usid; +u8 pid_base; };static const struct pinconf_generic_params pmic_gpio_bindings[] = {
@@ -949,12 +952,36 @@ static int pmic_gpio_child_to_parent_hwirq(struct gpio_chip *chip,unsigned int *parent_hwirq, unsigned int *parent_type) { - *parent_hwirq = child_hwirq +0xc0 ; + struct pmic_gpio_state *state = gpiochip_get_data(chip); + + *parent_hwirq = child_hwirq + state->pid_base; *parent_type = child_type;return 0 ; } +static void *pmic_gpio_populate_parent_fwspec (struct gpio_chip *chip, +unsigned int parent_hwirq, +unsigned int parent_type) +{ +struct pmic_gpio_state *state =gpiochip_get_data (chip); +struct irq_fwspec *fwspec; + + fwspec =kzalloc (sizeof (*fwspec),GFP_KERNEL ); +if (!fwspec) +return NULL ; + + fwspec->fwnode = chip->irq.parent_domain->fwnode; + + fwspec->param_count =4 ; + fwspec->param[0 ] = state->usid; + fwspec->param[1 ] = parent_hwirq; +/* param[2] must be left as 0 */ + fwspec->param[3 ] = parent_type; + +return fwspec; +} +static int pmic_gpio_probe (struct platform_device *pdev) {struct irq_domain *parent_domain;
@@ -965,6 +992,7 @@ static int pmic_gpio_probe(struct platform_device *pdev)struct pmic_gpio_pad *pad, *pads;struct pmic_gpio_state *state;struct gpio_irq_chip *girq; +const struct spmi_device *parent_spmi_dev;int ret, npins, i;u32 reg;
@@ -984,6 +1012,9 @@ static int pmic_gpio_probe(struct platform_device *pdev) state->dev = &pdev->dev; state->map =dev_get_regmap (dev->parent,NULL ); + parent_spmi_dev =to_spmi_device (dev->parent); + state->usid = parent_spmi_dev->usid; + state->pid_base = reg >>8 ; pindesc =devm_kcalloc (dev, npins,sizeof (*pindesc),GFP_KERNEL );if (!pindesc)
@@ -1059,7 +1090,7 @@ static int pmic_gpio_probe(struct platform_device *pdev) girq->fwnode =of_node_to_fwnode (state->dev->of_node); girq->parent_domain = parent_domain; girq->child_to_parent_hwirq = pmic_gpio_child_to_parent_hwirq; - girq->populate_parent_alloc_arg = gpiochip_populate_parent_fwspec_fourcell; + girq->populate_parent_alloc_arg = pmic_gpio_populate_parent_fwspec; girq->child_offset_to_irq = pmic_gpio_child_offset_to_irq; girq->child_irq_domain_ops.translate = pmic_gpio_domain_translate;
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
PATCH v4 2/2 arm64: dts: sc7280: Add volume up support for sc7280-idp
In reply to Satya PriyaFrom: satya priya <[email protected]>
Add pm7325 PMIC gpio support for vol+ on sc7280-idp.
---
Changes in V2:
- No changes.
Changes in V3:
- Sorted the nodes alphabetically.
Changes in V4:
- Updated the node names to replace underscores with hipens
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi +31 -0
@@ -239,6 +239,26 @@ cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; }; +&soc { + gpio-keys { + compatible = "gpio-keys"; + label = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&key_vol_up_default>; + + volume-up { + label = "volume_up"; + gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEUP>; + gpio-key,wakeup; + debounce-interval = <15>; + linux,can-disable; + }; + }; +}; + &uart5 { status = "okay"; };
@@ -284,6 +304,17 @@ /* PINCTRL - additions to nodes defined in sc7280.dtsi */ +&pm7325_gpios { + key_vol_up_default: key-vol-up-default { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + power-source = <0>; + qcom,drive-strength = <3>; + }; +}; + &qup_uart5_default { tx { pins = "gpio46";
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH V4 2/2] arm64: dts: sc7280: Add volume up support for sc7280-idp
Quoting Satya Priya (2021-09-14 05:55:08)
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi line 243
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi +2
-0@@ -239,6 +239,26 @@ cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; }; +&soc { + gpio-keys {
This should be in the root node, not soc node as it doesn't have any reg property. Please move it to / and put it at the top of the file.
Quoted 21 lines
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi +18
-0+ compatible = "gpio-keys"; + label = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&key_vol_up_default>; + + volume-up { + label = "volume_up"; + gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEUP>; + gpio-key,wakeup; + debounce-interval = <15>; + linux,can-disable; + }; + }; +}; + &uart5 { status = "okay"; };