soc: mediatek: SVS: introduce MTK SVS engine

1,446 lines not on this page · raw message

index fc7e2ee44a92..042c6e8e9069 100644
@@ -25,6 +25,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/thermal.h>
 
 /* svs bank 1-line sw id */
 #define SVSB_CPU_LITTLE			BIT(0)

@@ -36,6 +37,7 @@
 #define SVSB_MODE_ALL_DISABLE		0
 #define SVSB_MODE_INIT01		BIT(1)
 #define SVSB_MODE_INIT02		BIT(2)
+#define SVSB_MODE_MON			BIT(3)
 
 /* svs bank volt flags */
 #define SVSB_INIT01_PD_REQ		BIT(0)

@@ -53,11 +55,16 @@
 #define SVSB_EN_INIT01			0x1
 #define SVSB_EN_INIT02			0x5
 #define SVSB_EN_MASK			0x7
+#define SVSB_EN_MON			0x2
 #define SVSB_EN_OFF			0x0
 #define SVSB_INTEN_INIT0x		0x00005f01
+#define SVSB_INTEN_MONVOPEN		0x00ff0000
 #define SVSB_INTSTS_CLEAN		0x00ffffff
 #define SVSB_INTSTS_COMPLETE		0x1
+#define SVSB_INTSTS_MONVOP		0x00ff0000
 #define SVSB_RUNCONFIG_DEFAULT		0x80000000
+#define SVSB_TEMP_LOWER_BOUND		0xb2
+#define SVSB_TEMP_UPPER_BOUND		0x64
 
 static DEFINE_SPINLOCK(svs_lock);
 

@@ -66,6 +73,7 @@ static DEFINE_SPINLOCK(svs_lock);
  * @SVSB_PHASE_ERROR: svs bank encounters unexpected condition
  * @SVSB_PHASE_INIT01: svs bank basic init for data calibration
  * @SVSB_PHASE_INIT02: svs bank can provide voltages to opp table
+ * @SVSB_PHASE_MON: svs bank can provide voltages with thermal effect
  * @SVSB_PHASE_MAX: total number of svs bank phase (debug purpose)
  *
  * Each svs bank has its own independent phase and we enable each svs bank by

@@ -73,12 +81,13 @@ static DEFINE_SPINLOCK(svs_lock);
  * condition, it will fire an irq (PHASE_ERROR) to inform svs software.
  *
  * svs bank general phase-enabled order:
- * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02
+ * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02 -> SVSB_PHASE_MON
  */
 enum svsb_phase {
 	SVSB_PHASE_ERROR = 0,
 	SVSB_PHASE_INIT01,
 	SVSB_PHASE_INIT02,
+	SVSB_PHASE_MON,
 	SVSB_PHASE_MAX,
 };
 

@@ -209,9 +218,11 @@ static const u32 svs_regs_v2[] = {
  * @probe: svs platform probe function pointer
  * @irqflags: svs platform irq settings flags
  * @efuse_max: total number of svs efuse
+ * @tefuse_max: total number of thermal efuse
  * @regs: svs platform registers map
  * @bank_max: total number of svs banks
  * @efuse: svs efuse data received from NVMEM framework
+ * @tefuse: thermal efuse data received from NVMEM framework
  */
 struct svs_platform {
 	char *name;

@@ -224,9 +235,11 @@ struct svs_platform {
 	int (*probe)(struct svs_platform *svsp);
 	unsigned long irqflags;
 	size_t efuse_max;
+	size_t tefuse_max;
 	const u32 *regs;
 	u32 bank_max;
 	u32 *efuse;
+	u32 *tefuse;
 };
 
 /**

@@ -241,6 +254,7 @@ struct svs_platform {
  * @get_volts: function pointer to get bank voltages
  * @name: bank name
  * @buck_name: regulator name
+ * @tzone_name: thermal zone name
  * @suspended: suspend flag of this bank
  * @phase: bank current phase
  * @volt_od: bank voltage overdrive

@@ -270,6 +284,13 @@ struct svs_platform {
  * @sw_id: bank software identification
  * @cpu_id: cpu core id for SVS CPU bank use only
  * @ctl0: TS-x selection
+ * @temp: bank temperature
+ * @tzone_htemp: thermal zone high temperature threshold
+ * @tzone_htemp_voffset: thermal zone high temperature voltage offset
+ * @tzone_ltemp: thermal zone low temperature threshold
+ * @tzone_ltemp_voffset: thermal zone low temperature voltage offset
+ * @bts: svs efuse data
+ * @mts: svs efuse data
  * @bdes: svs efuse data
  * @mdes: svs efuse data
  * @mtdes: svs efuse data

@@ -292,6 +313,7 @@ struct svs_bank {
 	void (*get_volts)(struct svs_platform *svsp);
 	char *name;
 	char *buck_name;
+	char *tzone_name;
 	bool suspended;
 	enum svsb_phase phase;
 	s32 volt_od;

@@ -321,6 +343,13 @@ struct svs_bank {
 	u32 sw_id;
 	u32 cpu_id;
 	u32 ctl0;
+	u32 temp;
+	u32 tzone_htemp;
+	u32 tzone_htemp_voffset;
+	u32 tzone_ltemp;
+	u32 tzone_ltemp_voffset;
+	u32 bts;
+	u32 mts;
 	u32 bdes;
 	u32 mdes;
 	u32 mtdes;

@@ -361,10 +390,21 @@ static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
 	return (svsb_volt * svsb_volt_step) + svsb_volt_base;
 }
 
+static int svs_get_zone_temperature(const char *tzone_name, int *tzone_temp)
+{
+	struct thermal_zone_device *tzd;
+
+	tzd = thermal_zone_get_zone_by_name(tzone_name);
+	if (IS_ERR(tzd))
+		return PTR_ERR(tzd);
+
+	return thermal_zone_get_temp(tzd, tzone_temp);
+}
+
 static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 {
-	int ret = -EPERM;
-	u32 i, svsb_volt, opp_volt;
+	int ret = -EPERM, tzone_temp = 0;
+	u32 i, svsb_volt, opp_volt, temp_voffset = 0;
 
 	mutex_lock(&svsb->lock);
 

@@ -378,6 +418,22 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 		goto unlock_mutex;
 	}
 
+	/* Get thermal effect */
+	if (svsb->phase == SVSB_PHASE_MON) {
+		ret = svs_get_zone_temperature(svsb->tzone_name, &tzone_temp);
+		if (ret || (svsb->temp > SVSB_TEMP_UPPER_BOUND &&
+			    svsb->temp < SVSB_TEMP_LOWER_BOUND)) {
+			dev_err(svsb->dev, "%s: %d (0x%x), run default volts\n",
+				svsb->tzone_name, ret, svsb->temp);
+			svsb->phase = SVSB_PHASE_ERROR;
+		}
+
+		if (tzone_temp >= svsb->tzone_htemp)
+			temp_voffset += svsb->tzone_htemp_voffset;
+		else if (tzone_temp <= svsb->tzone_ltemp)
+			temp_voffset += svsb->tzone_ltemp_voffset;
+	}
+
 	/* vmin <= svsb_volt (opp_volt) <= default opp voltage */
 	for (i = 0; i < svsb->opp_count; i++) {
 		switch (svsb->phase) {

@@ -393,6 +449,13 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 							     svsb->volt_step,
 							     svsb->volt_base);
 			break;
+		case SVSB_PHASE_MON:
+			svsb_volt = max(svsb->volt[i] + temp_voffset,
+					svsb->vmin);
+			opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
+							     svsb->volt_step,
+							     svsb->volt_base);
+			break;
 		default:
 			dev_err(svsb->dev, "unknown phase: %u\n", svsb->phase);
 			ret = -EINVAL;

@@ -488,7 +551,7 @@ static void svs_set_bank_phase(struct svs_platform *svsp,
 {
 	struct svs_bank *svsb = svsp->pbank;
 	u32 des_char, temp_char, det_char, limit_vals;
-	u32 init2vals;
+	u32 init2vals, ts_calcs;
 
 	svs_switch_bank(svsp);
 

@@ -529,6 +592,12 @@ static void svs_set_bank_phase(struct svs_platform *svsp,
 		svs_writel_relaxed(svsp, init2vals, INIT2VALS);
 		svs_writel_relaxed(svsp, SVSB_EN_INIT02, SVSEN);
 		break;
+	case SVSB_PHASE_MON:
+		ts_calcs = (svsb->bts << 12) | svsb->mts;
+		svs_writel_relaxed(svsp, ts_calcs, TSCALCS);
+		svs_writel_relaxed(svsp, SVSB_INTEN_MONVOPEN, INTEN);
+		svs_writel_relaxed(svsp, SVSB_EN_MON, SVSEN);
+		break;
 	default:
 		dev_err(svsb->dev, "requested unknown target phase: %u\n",
 			target_phase);

@@ -548,6 +617,7 @@ static inline void svs_error_isr_handler(struct svs_platform *svsp)
 	dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n",
 		svs_readl_relaxed(svsp, SMSTATE0),
 		svs_readl_relaxed(svsp, SMSTATE1));
+	dev_err(svsb->dev, "TEMP = 0x%08x\n", svs_readl_relaxed(svsp, TEMP));
 
 	svsb->mode_support = SVSB_MODE_ALL_DISABLE;
 	svsb->phase = SVSB_PHASE_ERROR;

@@ -599,6 +669,17 @@ static inline void svs_init02_isr_handler(struct svs_platform *svsp)
 	svs_writel_relaxed(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
 }
 
+static inline void svs_mon_mode_isr_handler(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+
+	svsb->phase = SVSB_PHASE_MON;
+	svsb->temp = svs_readl_relaxed(svsp, TEMP) & GENMASK(7, 0);
+	svsb->get_volts(svsp);
+
+	svs_writel_relaxed(svsp, SVSB_INTSTS_MONVOP, INTSTS);
+}
+
 static irqreturn_t svs_isr(int irq, void *data)
 {
 	struct svs_platform *svsp = data;

@@ -629,6 +710,8 @@ static irqreturn_t svs_isr(int irq, void *data)
 		else if (int_sts == SVSB_INTSTS_COMPLETE &&
 			 svs_en == SVSB_EN_INIT02)
 			svs_init02_isr_handler(svsp);
+		else if (int_sts & SVSB_INTSTS_MONVOP)
+			svs_mon_mode_isr_handler(svsp);
 		else
 			svs_error_isr_handler(svsp);
 

@@ -858,6 +941,25 @@ static int svs_init02(struct svs_platform *svsp)
 	return 0;
 }
 
+static void svs_mon_mode(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	unsigned long flags;
+	u32 idx;
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_MON))
+			continue;
+
+		spin_lock_irqsave(&svs_lock, flags);
+		svsp->pbank = svsb;
+		svs_set_bank_phase(svsp, SVSB_PHASE_MON);
+		spin_unlock_irqrestore(&svs_lock, flags);
+	}
+}
+
 static int svs_start(struct svs_platform *svsp)
 {
 	int ret;

@@ -870,6 +972,8 @@ static int svs_start(struct svs_platform *svsp)
 	if (ret)
 		return ret;
 
+	svs_mon_mode(svsp);
+
 	return 0;
 }
 

@@ -923,6 +1027,8 @@ static int svs_resume(struct device *dev)
 	if (ret)
 		return ret;
 
+	svs_mon_mode(svsp);
+
 	return 0;
 }
 

@@ -1007,7 +1113,11 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
 static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb;
-	u32 idx, i, ft_pgm;
+	struct nvmem_cell *cell;
+	int format[6], x_roomt[6], o_vtsmcu[5], o_vtsabb, tb_roomt = 0;
+	int adc_ge_t, adc_oe_t, ge, oe, gain, degc_cali, adc_cali_en_t;
+	int o_slope, o_slope_sign, ts_id;
+	u32 idx, i, ft_pgm, mts, temp0, temp1, temp2;
 
 	for (i = 0; i < svsp->efuse_max; i++)
 		if (svsp->efuse[i])

@@ -1083,6 +1193,126 @@ static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
 		}
 	}
 
+	/* Get thermal efuse by nvmem */
+	cell = nvmem_cell_get(svsp->dev, "t-calibration-data");
+	if (IS_ERR(cell)) {
+		dev_err(svsp->dev, "no \"t-calibration-data\"? %ld\n",
+			PTR_ERR(cell));
+		goto remove_mt8183_svsb_mon_mode;
+	}
+
+	svsp->tefuse = nvmem_cell_read(cell, &svsp->tefuse_max);
+	if (IS_ERR(svsp->tefuse)) {
+		dev_err(svsp->dev, "cannot read thermal efuse: %ld\n",
+			PTR_ERR(svsp->tefuse));
+		goto remove_mt8183_svsb_mon_mode;
+	}
+
+	svsp->tefuse_max /= sizeof(u32);
+	nvmem_cell_put(cell);
+
+	/* Thermal efuse parsing */
+	adc_ge_t = (svsp->tefuse[1] >> 22) & GENMASK(9, 0);
+	adc_oe_t = (svsp->tefuse[1] >> 12) & GENMASK(9, 0);
+
+	o_vtsmcu[0] = (svsp->tefuse[0] >> 17) & GENMASK(8, 0);
+	o_vtsmcu[1] = (svsp->tefuse[0] >> 8) & GENMASK(8, 0);
+	o_vtsmcu[2] = svsp->tefuse[1] & GENMASK(8, 0);
+	o_vtsmcu[3] = (svsp->tefuse[2] >> 23) & GENMASK(8, 0);
+	o_vtsmcu[4] = (svsp->tefuse[2] >> 5) & GENMASK(8, 0);
+	o_vtsabb = (svsp->tefuse[2] >> 14) & GENMASK(8, 0);
+
+	degc_cali = (svsp->tefuse[0] >> 1) & GENMASK(5, 0);
+	adc_cali_en_t = svsp->tefuse[0] & BIT(0);
+	o_slope_sign = (svsp->tefuse[0] >> 7) & BIT(0);
+
+	ts_id = (svsp->tefuse[1] >> 9) & BIT(0);
+	o_slope = (svsp->tefuse[0] >> 26) & GENMASK(5, 0);
+
+	if (adc_cali_en_t == 1) {
+		if (!ts_id)
+			o_slope = 0;
+
+		if (adc_ge_t < 265 || adc_ge_t > 758 ||
+		    adc_oe_t < 265 || adc_oe_t > 758 ||
+		    o_vtsmcu[0] < -8 || o_vtsmcu[0] > 484 ||
+		    o_vtsmcu[1] < -8 || o_vtsmcu[1] > 484 ||
+		    o_vtsmcu[2] < -8 || o_vtsmcu[2] > 484 ||
+		    o_vtsmcu[3] < -8 || o_vtsmcu[3] > 484 ||
+		    o_vtsmcu[4] < -8 || o_vtsmcu[4] > 484 ||
+		    o_vtsabb < -8 || o_vtsabb > 484 ||
+		    degc_cali < 1 || degc_cali > 63) {
+			dev_err(svsp->dev, "bad thermal efuse, no mon mode\n");
+			goto remove_mt8183_svsb_mon_mode;
+		}
+	} else {
+		dev_err(svsp->dev, "no thermal efuse, no mon mode\n");
+		goto remove_mt8183_svsb_mon_mode;
+	}
+
+	ge = ((adc_ge_t - 512) * 10000) / 4096;
+	oe = (adc_oe_t - 512);
+	gain = (10000 + ge);
+
+	format[0] = (o_vtsmcu[0] + 3350 - oe);
+	format[1] = (o_vtsmcu[1] + 3350 - oe);
+	format[2] = (o_vtsmcu[2] + 3350 - oe);
+	format[3] = (o_vtsmcu[3] + 3350 - oe);
+	format[4] = (o_vtsmcu[4] + 3350 - oe);
+	format[5] = (o_vtsabb + 3350 - oe);
+
+	for (i = 0; i < 6; i++)
+		x_roomt[i] = (((format[i] * 10000) / 4096) * 10000) / gain;
+
+	temp0 = (10000 * 100000 / gain) * 15 / 18;
+
+	if (!o_slope_sign)
+		mts = (temp0 * 10) / (1534 + o_slope * 10);
+	else
+		mts = (temp0 * 10) / (1534 - o_slope * 10);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+		svsb->mts = mts;
+
+		switch (svsb->sw_id) {
+		case SVSB_CPU_LITTLE:
+			tb_roomt = x_roomt[3];
+			break;
+		case SVSB_CPU_BIG:
+			tb_roomt = x_roomt[4];
+			break;
+		case SVSB_CCI:
+			tb_roomt = x_roomt[3];
+			break;
+		case SVSB_GPU:
+			tb_roomt = x_roomt[1];
+			break;
+		default:
+			dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+			goto remove_mt8183_svsb_mon_mode;
+		}
+
+		temp0 = (degc_cali * 10 / 2);
+		temp1 = ((10000 * 100000 / 4096 / gain) *
+			 oe + tb_roomt * 10) * 15 / 18;
+
+		if (!o_slope_sign)
+			temp2 = temp1 * 100 / (1534 + o_slope * 10);
+		else
+			temp2 = temp1 * 100 / (1534 - o_slope * 10);
+
+		svsb->bts = (temp0 + temp2 - 250) * 4 / 10;
+	}
+
+	return true;
+
+remove_mt8183_svsb_mon_mode:
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+		svsb->mode_support &= ~SVSB_MODE_MON;
+	}
+
 	return true;
 }
 

@@ -1165,9 +1395,14 @@ static struct device *svs_add_device_link(struct svs_platform *svsp,
 
 static int svs_mt8183_platform_probe(struct svs_platform *svsp)
 {
+	struct device *dev;
 	struct svs_bank *svsb;
 	u32 idx;
 
+	dev = svs_add_device_link(svsp, "thermal");
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
+
 	for (idx = 0; idx < svsp->bank_max; idx++) {
 		svsb = &svsp->banks[idx];
 

@@ -1275,9 +1510,11 @@ static struct svs_bank svs_mt8183_banks[] = {
 		.set_freq_pct		= svs_set_bank_freq_pct_v2,
 		.get_volts		= svs_get_bank_volts_v2,
 		.buck_name		= "mali",
+		.tzone_name		= "tzts2",
 		.volt_flags		= SVSB_INIT01_PD_REQ |
 					  SVSB_INIT01_VOLT_INC_ONLY,
-		.mode_support		= SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+		.mode_support		= SVSB_MODE_INIT01 | SVSB_MODE_INIT02 |
+					  SVSB_MODE_MON,
 		.opp_count		= MAX_OPP_ENTRIES,
 		.freq_base		= 900000000,
 		.vboot			= 0x30,

@@ -1293,6 +1530,10 @@ static struct svs_bank svs_mt8183_banks[] = {
 		.core_sel		= 0x8fff0003,
 		.int_st			= BIT(3),
 		.ctl0			= 0x00050001,
+		.tzone_htemp		= 85000,
+		.tzone_htemp_voffset	= 0,
+		.tzone_ltemp		= 25000,
+		.tzone_ltemp_voffset	= 3,
 	},
 };
 

index 042c6e8e9069..93cdaecadd6d 100644
@@ -6,6 +6,7 @@
 #include <linux/bits.h>
 #include <linux/clk.h>
 #include <linux/completion.h>
+#include <linux/debugfs.h>
 #include <linux/device.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>

@@ -23,6 +24,7 @@
 #include <linux/pm_qos.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
+#include <linux/seq_file.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/thermal.h>

@@ -68,6 +70,39 @@
 
 static DEFINE_SPINLOCK(svs_lock);
 
+#define debug_fops_ro(name)						\
+	static int svs_##name##_debug_open(struct inode *inode,		\
+					   struct file *filp)		\
+	{								\
+		return single_open(filp, svs_##name##_debug_show,	\
+				   inode->i_private);			\
+	}								\
+	static const struct file_operations svs_##name##_debug_fops = {	\
+		.owner = THIS_MODULE,					\
+		.open = svs_##name##_debug_open,			\
+		.read = seq_read,					\
+		.llseek = seq_lseek,					\
+		.release = single_release,				\
+	}
+
+#define debug_fops_rw(name)						\
+	static int svs_##name##_debug_open(struct inode *inode,		\
+					   struct file *filp)		\
+	{								\
+		return single_open(filp, svs_##name##_debug_show,	\
+				   inode->i_private);			\
+	}								\
+	static const struct file_operations svs_##name##_debug_fops = {	\
+		.owner = THIS_MODULE,					\
+		.open = svs_##name##_debug_open,			\
+		.read = seq_read,					\
+		.write = svs_##name##_debug_write,			\
+		.llseek = seq_lseek,					\
+		.release = single_release,				\
+	}
+
+#define svs_dentry_data(name)	{__stringify(name), &svs_##name##_debug_fops}
+
 /**
  * enum svsb_phase - svs bank phase enumeration
  * @SVSB_PHASE_ERROR: svs bank encounters unexpected condition

@@ -258,6 +293,8 @@ struct svs_platform {
  * @suspended: suspend flag of this bank
  * @phase: bank current phase
  * @volt_od: bank voltage overdrive
+ * @voffset: bank voltage offset for debug purpose
+ * @reg_data: bank register data in different phase for debug purpose
  * @pm_runtime_enabled_count: bank pm runtime enabled count
  * @mode_support: bank mode support.
  * @freq_base: reference frequency for bank init

@@ -317,6 +354,8 @@ struct svs_bank {
 	bool suspended;
 	enum svsb_phase phase;
 	s32 volt_od;
+	s32 voffset;
+	u32 reg_data[SVSB_PHASE_MAX][SVS_REG_MAX];
 	u32 pm_runtime_enabled_count;
 	u32 mode_support;
 	u32 freq_base;

@@ -444,14 +483,15 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 			/* do nothing */
 			goto unlock_mutex;
 		case SVSB_PHASE_INIT02:
-			svsb_volt = max(svsb->volt[i], svsb->vmin);
+			svsb_volt = max(svsb->volt[i] + svsb->voffset,
+					svsb->vmin);
 			opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
 							     svsb->volt_step,
 							     svsb->volt_base);
 			break;
 		case SVSB_PHASE_MON:
-			svsb_volt = max(svsb->volt[i] + temp_voffset,
-					svsb->vmin);
+			svsb_volt = max(svsb->volt[i] + temp_voffset +
+					svsb->voffset, svsb->vmin);
 			opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
 							     svsb->volt_step,
 							     svsb->volt_base);

@@ -480,6 +520,257 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 	return ret;
 }
 
+static int svs_dump_debug_show(struct seq_file *m, void *p)
+{
+	struct svs_platform *svsp = (struct svs_platform *)m->private;
+	struct svs_bank *svsb;
+	unsigned long svs_reg_addr;
+	u32 idx, i, j, bank_id;
+
+	for (i = 0; i < svsp->efuse_max; i++)
+		if (svsp->efuse && svsp->efuse[i])
+			seq_printf(m, "M_HW_RES%d = 0x%08x\n",
+				   i, svsp->efuse[i]);
+
+	for (i = 0; i < svsp->tefuse_max; i++)
+		if (svsp->tefuse)
+			seq_printf(m, "THERMAL_EFUSE%d = 0x%08x\n",
+				   i, svsp->tefuse[i]);
+
+	for (bank_id = 0, idx = 0; idx < svsp->bank_max; idx++, bank_id++) {
+		svsb = &svsp->banks[idx];
+
+		for (i = SVSB_PHASE_INIT01; i <= SVSB_PHASE_MON; i++) {
+			seq_printf(m, "Bank_number = %u\n", bank_id);
+
+			if (i == SVSB_PHASE_INIT01 || i == SVSB_PHASE_INIT02)
+				seq_printf(m, "mode = init%d\n", i);
+			else if (i == SVSB_PHASE_MON)
+				seq_puts(m, "mode = mon\n");
+			else
+				seq_puts(m, "mode = error\n");
+
+			for (j = DESCHAR; j < SVS_REG_MAX; j++) {
+				svs_reg_addr = (unsigned long)(svsp->base +
+							       svsp->regs[j]);
+				seq_printf(m, "0x%08lx = 0x%08x\n",
+					   svs_reg_addr, svsb->reg_data[i][j]);
+			}
+		}
+	}
+
+	return 0;
+}
+
+debug_fops_ro(dump);
+
+static int svs_enable_debug_show(struct seq_file *m, void *v)
+{
+	struct svs_bank *svsb = (struct svs_bank *)m->private;
+
+	switch (svsb->phase) {
+	case SVSB_PHASE_ERROR:
+		seq_puts(m, "disabled\n");
+		break;
+	case SVSB_PHASE_INIT01:
+		seq_puts(m, "init1\n");
+		break;
+	case SVSB_PHASE_INIT02:
+		seq_puts(m, "init2\n");
+		break;
+	case SVSB_PHASE_MON:
+		seq_puts(m, "mon mode\n");
+		break;
+	default:
+		seq_puts(m, "unknown\n");
+		break;
+	}
+
+	return 0;
+}
+
+static ssize_t svs_enable_debug_write(struct file *filp,
+				      const char __user *buffer,
+				      size_t count, loff_t *pos)
+{
+	struct svs_bank *svsb = file_inode(filp)->i_private;
+	struct svs_platform *svsp = dev_get_drvdata(svsb->dev);
+	unsigned long flags;
+	int enabled, ret;
+	char *buf = NULL;
+
+	if (count >= PAGE_SIZE)
+		return -EINVAL;
+
+	buf = (char *)memdup_user_nul(buffer, count);
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	ret = kstrtoint(buf, 10, &enabled);
+	if (ret)
+		return ret;
+
+	if (!enabled) {
+		spin_lock_irqsave(&svs_lock, flags);
+		svsp->pbank = svsb;
+		svsb->mode_support = SVSB_MODE_ALL_DISABLE;
+		svs_switch_bank(svsp);
+		svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+		svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+		spin_unlock_irqrestore(&svs_lock, flags);
+
+		svsb->phase = SVSB_PHASE_ERROR;
+		svs_adjust_pm_opp_volts(svsb, true);
+	}
+
+	kfree(buf);
+
+	return count;
+}
+
+debug_fops_rw(enable);
+
+static int svs_status_debug_show(struct seq_file *m, void *v)
+{
+	struct svs_bank *svsb = (struct svs_bank *)m->private;
+	struct dev_pm_opp *opp;
+	int tzone_temp = 0, ret;
+	u32 i;
+
+	ret = svs_get_zone_temperature(svsb->tzone_name, &tzone_temp);
+	if (ret)
+		seq_printf(m, "%s: temperature ignore\n", svsb->name);
+	else
+		seq_printf(m, "%s: temperature = %d\n", svsb->name, tzone_temp);
+
+	for (i = 0; i < svsb->opp_count; i++) {
+		opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
+						 svsb->opp_dfreq[i], true);
+		if (IS_ERR(opp)) {
+			seq_printf(m, "%s: cannot find freq = %u (%ld)\n",
+				   svsb->name, svsb->opp_dfreq[i],
+				   PTR_ERR(opp));
+			return PTR_ERR(opp);
+		}
+
+		seq_printf(m, "opp_freq[%02u]: %u, opp_volt[%02u]: %lu, ",
+			   i, svsb->opp_dfreq[i], i,
+			   dev_pm_opp_get_voltage(opp));
+		seq_printf(m, "svsb_volt[%02u]: 0x%x, freq_pct[%02u]: %u\n",
+			   i, svsb->volt[i], i, svsb->freq_pct[i]);
+		dev_pm_opp_put(opp);
+	}
+
+	return 0;
+}
+
+debug_fops_ro(status);
+
+static int svs_voffset_debug_show(struct seq_file *m, void *v)
+{
+	struct svs_bank *svsb = (struct svs_bank *)m->private;
+
+	seq_printf(m, "%d\n", svsb->voffset);
+
+	return 0;
+}
+
+static ssize_t svs_voffset_debug_write(struct file *filp,
+				       const char __user *buffer,
+				       size_t count, loff_t *pos)
+{
+	struct svs_bank *svsb = file_inode(filp)->i_private;
+	char *buf = NULL;
+	s32 voffset;
+
+	if (count >= PAGE_SIZE)
+		return -EINVAL;
+
+	buf = (char *)memdup_user_nul(buffer, count);
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	if (!kstrtoint(buf, 10, &voffset)) {
+		svsb->voffset = voffset;
+		svs_adjust_pm_opp_volts(svsb, true);
+	}
+
+	kfree(buf);
+
+	return count;
+}
+
+debug_fops_rw(voffset);
+
+static int svs_create_debug_cmds(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	struct dentry *svs_dir, *svsb_dir, *file_entry;
+	const char *d = "/sys/kernel/debug/svs";
+	u32 i, idx;
+
+	struct svs_dentry {
+		const char *name;
+		const struct file_operations *fops;
+	};
+
+	struct svs_dentry svs_entries[] = {
+		svs_dentry_data(dump),
+	};
+
+	struct svs_dentry svsb_entries[] = {
+		svs_dentry_data(enable),
+		svs_dentry_data(status),
+		svs_dentry_data(voffset),
+	};
+
+	svs_dir = debugfs_create_dir("svs", NULL);
+	if (IS_ERR(svs_dir)) {
+		dev_err(svsp->dev, "cannot create %s: %ld\n",
+			d, PTR_ERR(svs_dir));
+		return PTR_ERR(svs_dir);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(svs_entries); i++) {
+		file_entry = debugfs_create_file(svs_entries[i].name, 0664,
+						 svs_dir, svsp,
+						 svs_entries[i].fops);
+		if (IS_ERR(file_entry)) {
+			dev_err(svsp->dev, "cannot create %s/%s: %ld\n",
+				d, svs_entries[i].name, PTR_ERR(file_entry));
+			return PTR_ERR(file_entry);
+		}
+	}
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (svsb->mode_support == SVSB_MODE_ALL_DISABLE)
+			continue;
+
+		svsb_dir = debugfs_create_dir(svsb->name, svs_dir);
+		if (IS_ERR(svsb_dir)) {
+			dev_err(svsp->dev, "cannot create %s/%s: %ld\n",
+				d, svsb->name, PTR_ERR(svsb_dir));
+			return PTR_ERR(svsb_dir);
+		}
+
+		for (i = 0; i < ARRAY_SIZE(svsb_entries); i++) {
+			file_entry = debugfs_create_file(svsb_entries[i].name,
+							 0664, svsb_dir, svsb,
+							 svsb_entries[i].fops);
+			if (IS_ERR(file_entry)) {
+				dev_err(svsp->dev, "no %s/%s/%s?: %ld\n",
+					d, svsb->name, svsb_entries[i].name,
+					PTR_ERR(file_entry));
+				return PTR_ERR(file_entry);
+			}
+		}
+	}
+
+	return 0;
+}
+
 static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
 {
 	u32 vx;

@@ -605,6 +896,16 @@ static void svs_set_bank_phase(struct svs_platform *svsp,
 	}
 }
 
+static inline void svs_save_bank_register_data(struct svs_platform *svsp,
+					       enum svsb_phase phase)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	enum svs_reg_index rg_i;
+
+	for (rg_i = DESCHAR; rg_i < SVS_REG_MAX; rg_i++)
+		svsb->reg_data[phase][rg_i] = svs_readl_relaxed(svsp, rg_i);
+}
+
 static inline void svs_error_isr_handler(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb = svsp->pbank;

@@ -619,6 +920,8 @@ static inline void svs_error_isr_handler(struct svs_platform *svsp)
 		svs_readl_relaxed(svsp, SMSTATE1));
 	dev_err(svsb->dev, "TEMP = 0x%08x\n", svs_readl_relaxed(svsp, TEMP));
 
+	svs_save_bank_register_data(svsp, SVSB_PHASE_ERROR);
+
 	svsb->mode_support = SVSB_MODE_ALL_DISABLE;
 	svsb->phase = SVSB_PHASE_ERROR;
 

@@ -635,6 +938,8 @@ static inline void svs_init01_isr_handler(struct svs_platform *svsp)
 		 svs_readl_relaxed(svsp, VDESIGN30),
 		 svs_readl_relaxed(svsp, DCVALUES));
 
+	svs_save_bank_register_data(svsp, SVSB_PHASE_INIT01);
+
 	svsb->phase = SVSB_PHASE_INIT01;
 	svsb->dc_voffset_in = ~(svs_readl_relaxed(svsp, DCVALUES) &
 				GENMASK(15, 0)) + 1;

@@ -662,6 +967,8 @@ static inline void svs_init02_isr_handler(struct svs_platform *svsp)
 		 svs_readl_relaxed(svsp, VOP30),
 		 svs_readl_relaxed(svsp, DCVALUES));
 
+	svs_save_bank_register_data(svsp, SVSB_PHASE_INIT02);
+
 	svsb->phase = SVSB_PHASE_INIT02;
 	svsb->get_volts(svsp);
 

@@ -673,6 +980,8 @@ static inline void svs_mon_mode_isr_handler(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb = svsp->pbank;
 
+	svs_save_bank_register_data(svsp, SVSB_PHASE_MON);
+
 	svsb->phase = SVSB_PHASE_MON;
 	svsb->temp = svs_readl_relaxed(svsp, TEMP) & GENMASK(7, 0);
 	svsb->get_volts(svsp);

@@ -1658,6 +1967,12 @@ static int svs_probe(struct platform_device *pdev)
 		goto svs_probe_iounmap;
 	}
 
+	ret = svs_create_debug_cmds(svsp);
+	if (ret) {
+		dev_err(svsp->dev, "svs create debug cmds fail: %d\n", ret);
+		goto svs_probe_iounmap;
+	}
+
 	return 0;
 
 svs_probe_iounmap:

index 93cdaecadd6d..bec6524ab33a 100644
@@ -24,6 +24,7 @@
 #include <linux/pm_qos.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
+#include <linux/reset.h>
 #include <linux/seq_file.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>

@@ -35,6 +36,10 @@
 #define SVSB_CCI			BIT(2)
 #define SVSB_GPU			BIT(3)
 
+/* svs bank 2-line type */
+#define SVSB_LOW			BIT(8)
+#define SVSB_HIGH			BIT(9)
+
 /* svs bank mode support */
 #define SVSB_MODE_ALL_DISABLE		0
 #define SVSB_MODE_INIT01		BIT(1)

@@ -45,6 +50,8 @@
 #define SVSB_INIT01_PD_REQ		BIT(0)
 #define SVSB_INIT01_VOLT_IGNORE		BIT(1)
 #define SVSB_INIT01_VOLT_INC_ONLY	BIT(2)
+#define SVSB_MON_VOLT_IGNORE		BIT(16)
+#define SVSB_REMOVE_DVTFIXED_VOLT	BIT(24)
 
 /* svs bank common setting */
 #define MAX_OPP_ENTRIES			16

@@ -249,6 +256,7 @@ static const u32 svs_regs_v2[] = {
  * @main_clk: main clock for svs bank
  * @pbank: svs bank pointer protected by spin_lock section
  * @banks: svs banks that svs platform supports
+ * @rst: svs platform reset control
  * @efuse_parsing: svs platform efuse parsing function pointer
  * @probe: svs platform probe function pointer
  * @irqflags: svs platform irq settings flags

@@ -266,6 +274,7 @@ struct svs_platform {
 	struct clk *main_clk;
 	struct svs_bank *pbank;
 	struct svs_bank *banks;
+	struct reset_control *rst;
 	bool (*efuse_parsing)(struct svs_platform *svsp);
 	int (*probe)(struct svs_platform *svsp);
 	unsigned long irqflags;

@@ -298,6 +307,7 @@ struct svs_platform {
  * @pm_runtime_enabled_count: bank pm runtime enabled count
  * @mode_support: bank mode support.
  * @freq_base: reference frequency for bank init
+ * @turn_freq_base: refenrece frequency for turn point
  * @vboot: voltage request for bank init01 only
  * @opp_dfreq: default opp frequency table
  * @opp_dvolt: default opp voltage table

@@ -333,6 +343,8 @@ struct svs_platform {
  * @mtdes: svs efuse data
  * @dcbdet: svs efuse data
  * @dcmdet: svs efuse data
+ * @turn_pt: turn point informs which opp_volt calculated by high/low bank.
+ * @type: bank type to represent it is 2-line (high/low) bank or 1-line bank.
  *
  * Svs bank will generate suitalbe voltages by below general math equation
  * and provide these voltages to opp voltage table.

@@ -359,6 +371,7 @@ struct svs_bank {
 	u32 pm_runtime_enabled_count;
 	u32 mode_support;
 	u32 freq_base;
+	u32 turn_freq_base;
 	u32 vboot;
 	u32 opp_dfreq[MAX_OPP_ENTRIES];
 	u32 opp_dvolt[MAX_OPP_ENTRIES];

@@ -394,6 +407,8 @@ struct svs_bank {
 	u32 mtdes;
 	u32 dcbdet;
 	u32 dcmdet;
+	u32 turn_pt;
+	u32 type;
 };
 
 static u32 percent(u32 numerator, u32 denominator)

@@ -429,6 +444,37 @@ static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
 	return (svsb_volt * svsb_volt_step) + svsb_volt_base;
 }
 
+static u32 svs_opp_volt_to_bank_volt(u32 opp_u_volt, u32 svsb_volt_step,
+				     u32 svsb_volt_base)
+{
+	return (opp_u_volt - svsb_volt_base) / svsb_volt_step;
+}
+
+static int svs_sync_bank_volts_from_opp(struct svs_bank *svsb)
+{
+	struct dev_pm_opp *opp;
+	u32 i, opp_u_volt;
+
+	for (i = 0; i < svsb->opp_count; i++) {
+		opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
+						 svsb->opp_dfreq[i],
+						 true);
+		if (IS_ERR(opp)) {
+			dev_err(svsb->dev, "cannot find freq = %u (%ld)\n",
+				svsb->opp_dfreq[i], PTR_ERR(opp));
+			return PTR_ERR(opp);
+		}
+
+		opp_u_volt = dev_pm_opp_get_voltage(opp);
+		svsb->volt[i] = svs_opp_volt_to_bank_volt(opp_u_volt,
+							  svsb->volt_step,
+							  svsb->volt_base);
+		dev_pm_opp_put(opp);
+	}
+
+	return 0;
+}
+
 static int svs_get_zone_temperature(const char *tzone_name, int *tzone_temp)
 {
 	struct thermal_zone_device *tzd;

@@ -443,7 +489,7 @@ static int svs_get_zone_temperature(const char *tzone_name, int *tzone_temp)
 static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 {
 	int ret = -EPERM, tzone_temp = 0;
-	u32 i, svsb_volt, opp_volt, temp_voffset = 0;
+	u32 i, svsb_volt, opp_volt, temp_voffset = 0, opp_start, opp_stop;
 
 	mutex_lock(&svsb->lock);
 

@@ -457,6 +503,21 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 		goto unlock_mutex;
 	}
 
+	/*
+	 * 2-line bank updates its corresponding opp volts.
+	 * 1-line bank updates all opp volts.
+	 */
+	if (svsb->type == SVSB_HIGH) {
+		opp_start = 0;
+		opp_stop = svsb->turn_pt;
+	} else if (svsb->type == SVSB_LOW) {
+		opp_start = svsb->turn_pt;
+		opp_stop = svsb->opp_count;
+	} else {
+		opp_start = 0;
+		opp_stop = svsb->opp_count;
+	}
+
 	/* Get thermal effect */
 	if (svsb->phase == SVSB_PHASE_MON) {
 		ret = svs_get_zone_temperature(svsb->tzone_name, &tzone_temp);

@@ -471,10 +532,16 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 			temp_voffset += svsb->tzone_htemp_voffset;
 		else if (tzone_temp <= svsb->tzone_ltemp)
 			temp_voffset += svsb->tzone_ltemp_voffset;
+
+		/* 2-line bank update all opp volts when running mode */
+		if (svsb->type == SVSB_HIGH || svsb->type == SVSB_LOW) {
+			opp_start = 0;
+			opp_stop = svsb->opp_count;
+		}
 	}
 
 	/* vmin <= svsb_volt (opp_volt) <= default opp voltage */
-	for (i = 0; i < svsb->opp_count; i++) {
+	for (i = opp_start; i < opp_stop; i++) {
 		switch (svsb->phase) {
 		case SVSB_PHASE_ERROR:
 			opp_volt = svsb->opp_dvolt[i];

@@ -639,9 +706,11 @@ static int svs_status_debug_show(struct seq_file *m, void *v)
 
 	ret = svs_get_zone_temperature(svsb->tzone_name, &tzone_temp);
 	if (ret)
-		seq_printf(m, "%s: temperature ignore\n", svsb->name);
+		seq_printf(m, "%s: temperature ignore, turn_pt = %u\n",
+			   svsb->name, svsb->turn_pt);
 	else
-		seq_printf(m, "%s: temperature = %d\n", svsb->name, tzone_temp);
+		seq_printf(m, "%s: temperature = %d, turn_pt = %u\n",
+			   svsb->name, tzone_temp, svsb->turn_pt);
 
 	for (i = 0; i < svsb->opp_count; i++) {
 		opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,

@@ -784,6 +853,181 @@ static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
 	return DIV_ROUND_UP(vx, 100);
 }
 
+static void svs_get_bank_volts_v3(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	u32 i, j, *vop, vop74, vop30, mask7_0 = GENMASK(7, 0);
+	u32 b_sft, bits8 = 8, shift_byte = 0, reg_bytes = 4;
+	u32 middle_index = (svsb->opp_count / 2);
+	u32 opp_start = 0, opp_stop = 0, turn_pt = svsb->turn_pt;
+
+	if (svsb->phase == SVSB_PHASE_MON &&
+	    svsb->volt_flags & SVSB_MON_VOLT_IGNORE)
+		return;
+
+	vop74 = svs_readl_relaxed(svsp, VOP74);
+	vop30 = svs_readl_relaxed(svsp, VOP30);
+
+	/* Target is to set svsb->volt[] by algorithm */
+	if (turn_pt < middle_index) {
+		if (svsb->type == SVSB_HIGH) {
+			/* volt[0] ~ volt[turn_pt - 1] */
+			for (i = 0; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+		} else if (svsb->type == SVSB_LOW) {
+			/* volt[turn_pt] + volt[j] ~ volt[opp_count - 1] */
+			j = svsb->opp_count - 7;
+			svsb->volt[turn_pt] = vop30 & mask7_0;
+			shift_byte++;
+			for (i = j; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+
+			/* volt[turn_pt + 1] ~ volt[j - 1] by interpolate */
+			for (i = turn_pt + 1; i < j; i++)
+				svsb->volt[i] =
+					interpolate(svsb->freq_pct[turn_pt],
+						    svsb->freq_pct[j],
+						    svsb->volt[turn_pt],
+						    svsb->volt[j],
+						    svsb->freq_pct[i]);
+		}
+	} else {
+		if (svsb->type == SVSB_HIGH) {
+			/* volt[0] + volt[j] ~ volt[turn_pt - 1] */
+			j = turn_pt - 7;
+			svsb->volt[0] = vop30 & mask7_0;
+			shift_byte++;
+			for (i = j; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+
+			/* volt[1] ~ volt[j - 1] by interpolate */
+			for (i = 1; i < j; i++)
+				svsb->volt[i] =
+					interpolate(svsb->freq_pct[0],
+						    svsb->freq_pct[j],
+						    svsb->volt[0],
+						    svsb->volt[j],
+						    svsb->freq_pct[i]);
+		} else if (svsb->type == SVSB_LOW) {
+			/* volt[turn_pt] ~ volt[opp_count - 1] */
+			for (i = turn_pt; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+		}
+	}
+
+	if (svsb->type == SVSB_HIGH) {
+		opp_start = 0;
+		opp_stop = svsb->turn_pt;
+	} else if (svsb->type == SVSB_LOW) {
+		opp_start = svsb->turn_pt;
+		opp_stop = svsb->opp_count;
+	}
+
+	for (i = opp_start; i < opp_stop; i++)
+		if (svsb->volt_flags & SVSB_REMOVE_DVTFIXED_VOLT)
+			svsb->volt[i] -= svsb->dvt_fixed;
+}
+
+static void svs_set_bank_freq_pct_v3(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	u32 i, j, *freq_pct, freq_pct74 = 0, freq_pct30 = 0;
+	u32 b_sft, bits8 = 8, shift_byte = 0, reg_bytes = 4;
+	u32 middle_index = (svsb->opp_count / 2);
+	u32 turn_pt = middle_index;
+
+	for (i = 0; i < svsb->opp_count; i++) {
+		if (svsb->opp_dfreq[i] <= svsb->turn_freq_base) {
+			svsb->turn_pt = i;
+			break;
+		}
+	}
+
+	turn_pt = svsb->turn_pt;
+
+	/* Target is to fill out freq_pct74 / freq_pct30 by algorithm */
+	if (turn_pt < middle_index) {
+		if (svsb->type == SVSB_HIGH) {
+			/* Edge case for preventing freq_pct30 from being 0 */
+			if (turn_pt == 0)
+				freq_pct30 = svsb->freq_pct[0];
+
+			/* freq_pct[0] ~ freq_pct[turn_pt - 1] */
+			for (i = 0; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		} else if (svsb->type == SVSB_LOW) {
+			/*
+			 * freq_pct[turn_pt] +
+			 * freq_pct[opp_count - 7] ~ freq_pct[opp_count -1]
+			 */
+			freq_pct30 = svsb->freq_pct[turn_pt];
+			shift_byte++;
+			j = svsb->opp_count - 7;
+			for (i = j; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		}
+	} else {
+		if (svsb->type == SVSB_HIGH) {
+			/*
+			 * freq_pct[0] +
+			 * freq_pct[turn_pt - 7] ~ freq_pct[turn_pt - 1]
+			 */
+			freq_pct30 = svsb->freq_pct[0];
+			shift_byte++;
+			j = turn_pt - 7;
+			for (i = j; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		} else if (svsb->type == SVSB_LOW) {
+			/* freq_pct[turn_pt] ~ freq_pct[opp_count - 1] */
+			for (i = turn_pt; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		}
+	}
+
+	svs_writel_relaxed(svsp, freq_pct74, FREQPCT74);
+	svs_writel_relaxed(svsp, freq_pct30, FREQPCT30);
+}
+
 static void svs_get_bank_volts_v2(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb = svsp->pbank;

@@ -1247,6 +1491,25 @@ static int svs_init02(struct svs_platform *svsp)
 		}
 	}
 
+	/*
+	 * 2-line high/low bank update its corresponding opp voltages only.
+	 * Therefore, we sync voltages from opp for high/low bank voltages
+	 * consistency.
+	 */
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT02))
+			continue;
+
+		if (svsb->type == SVSB_HIGH || svsb->type == SVSB_LOW) {
+			if (svs_sync_bank_volts_from_opp(svsb)) {
+				dev_err(svsb->dev, "sync volt fail\n");
+				return -EPERM;
+			}
+		}
+	}
+
 	return 0;
 }
 

@@ -1291,6 +1554,7 @@ static int svs_suspend(struct device *dev)
 	struct svs_platform *svsp = dev_get_drvdata(dev);
 	struct svs_bank *svsb;
 	unsigned long flags;
+	int ret;
 	u32 idx;
 
 	for (idx = 0; idx < svsp->bank_max; idx++) {

@@ -1309,6 +1573,12 @@ static int svs_suspend(struct device *dev)
 		svs_adjust_pm_opp_volts(svsb, true);
 	}
 
+	ret = reset_control_assert(svsp->rst);
+	if (ret) {
+		dev_err(svsp->dev, "cannot assert reset %d\n", ret);
+		return ret;
+	}
+
 	clk_disable_unprepare(svsp->main_clk);
 
 	return 0;

@@ -1327,6 +1597,12 @@ static int svs_resume(struct device *dev)
 		return ret;
 	}
 
+	ret = reset_control_deassert(svsp->rst);
+	if (ret) {
+		dev_err(svsp->dev, "cannot deassert reset %d\n", ret);
+		return ret;
+	}
+
 	for (idx = 0; idx < svsp->bank_max; idx++) {
 		svsb = &svsp->banks[idx];
 		svsb->suspended = false;

@@ -1365,7 +1641,12 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
 			svsb->name = "SVSB_CCI";
 			break;
 		case SVSB_GPU:
-			svsb->name = "SVSB_GPU";
+			if (svsb->type == SVSB_HIGH)
+				svsb->name = "SVSB_GPU_HIGH";
+			else if (svsb->type == SVSB_LOW)
+				svsb->name = "SVSB_GPU_LOW";
+			else
+				svsb->name = "SVSB_GPU";
 			break;
 		default:
 			dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);

@@ -1419,6 +1700,84 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
 	return 0;
 }
 
+static bool svs_mt8192_efuse_parsing(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	struct nvmem_cell *cell;
+	u32 idx, i, vmin, golden_temp;
+
+	for (i = 0; i < svsp->efuse_max; i++)
+		if (svsp->efuse[i])
+			dev_info(svsp->dev, "M_HW_RES%d: 0x%08x\n",
+				 i, svsp->efuse[i]);
+
+	if (!svsp->efuse[9]) {
+		dev_notice(svsp->dev, "svs_efuse[9] = 0x0?\n");
+		return false;
+	}
+
+	/* Svs efuse parsing */
+	vmin = (svsp->efuse[19] >> 4) & GENMASK(1, 0);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (vmin == 0x1)
+			svsb->vmin = 0x1e;
+
+		if (svsb->type == SVSB_LOW) {
+			svsb->mtdes = svsp->efuse[10] & GENMASK(7, 0);
+			svsb->bdes = (svsp->efuse[10] >> 16) & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[10] >> 24) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[17]) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[17] >> 8) & GENMASK(7, 0);
+		} else if (svsb->type == SVSB_HIGH) {
+			svsb->mtdes = svsp->efuse[9] & GENMASK(7, 0);
+			svsb->bdes = (svsp->efuse[9] >> 16) & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[9] >> 24) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[17] >> 16) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[17] >> 24) & GENMASK(7, 0);
+		}
+
+		svsb->vmax += svsb->dvt_fixed;
+	}
+
+	/* Thermal efuse parsing */
+	cell = nvmem_cell_get(svsp->dev, "t-calibration-data");
+	if (IS_ERR_OR_NULL(cell)) {
+		dev_err(svsp->dev, "no \"t-calibration-data\"? %ld\n",
+			PTR_ERR(cell));
+		return false;
+	}
+
+	svsp->tefuse = nvmem_cell_read(cell, &svsp->tefuse_max);
+	if (IS_ERR(svsp->tefuse)) {
+		dev_err(svsp->dev, "cannot read thermal efuse: %ld\n",
+			PTR_ERR(svsp->tefuse));
+		return false;
+	}
+
+	svsp->tefuse_max /= sizeof(u32);
+	nvmem_cell_put(cell);
+
+	for (i = 0; i < svsp->tefuse_max; i++)
+		if (svsp->tefuse[i] != 0)
+			break;
+
+	if (i == svsp->tefuse_max)
+		golden_temp = 50; /* All thermal efuse data are 0 */
+	else
+		golden_temp = (svsp->tefuse[0] >> 24) & GENMASK(7, 0);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+		svsb->mts = 500;
+		svsb->bts = (((500 * golden_temp + 250460) / 1000) - 25) * 4;
+	}
+
+	return true;
+}
+
 static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb;

@@ -1702,6 +2061,38 @@ static struct device *svs_add_device_link(struct svs_platform *svsp,
 	return dev;
 }
 
+static int svs_mt8192_platform_probe(struct svs_platform *svsp)
+{
+	struct device *dev;
+	struct svs_bank *svsb;
+	u32 idx;
+
+	svsp->rst = devm_reset_control_get_optional(svsp->dev, "svs_rst");
+	if (IS_ERR(svsp->rst)) {
+		dev_err_probe(svsp->dev, PTR_ERR(svsp->rst),
+			      "cannot get svs reset control\n");
+		return PTR_ERR(svsp->rst);
+	}
+
+	dev = svs_add_device_link(svsp, "lvts");
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (svsb->type == SVSB_HIGH)
+			svsb->opp_dev = svs_add_device_link(svsp, "mali");
+		else if (svsb->type == SVSB_LOW)
+			svsb->opp_dev = svs_get_subsys_device(svsp, "mali");
+
+		if (IS_ERR(svsb->opp_dev))
+			return PTR_ERR(svsb->opp_dev);
+	}
+
+	return 0;
+}
+
 static int svs_mt8183_platform_probe(struct svs_platform *svsp)
 {
 	struct device *dev;

@@ -1742,6 +2133,61 @@ static int svs_mt8183_platform_probe(struct svs_platform *svsp)
 	return 0;
 }
 
+static struct svs_bank svs_mt8192_banks[] = {
+	{
+		.sw_id			= SVSB_GPU,
+		.type			= SVSB_LOW,
+		.set_freq_pct		= svs_set_bank_freq_pct_v3,
+		.get_volts		= svs_get_bank_volts_v3,
+		.volt_flags		= SVSB_REMOVE_DVTFIXED_VOLT,
+		.mode_support		= SVSB_MODE_INIT02,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 688000000,
+		.turn_freq_base		= 688000000,
+		.volt_step		= 6250,
+		.volt_base		= 400000,
+		.vmax			= 0x60,
+		.vmin			= 0x1a,
+		.age_config		= 0x555555,
+		.dc_config		= 0x1,
+		.dvt_fixed		= 0x1,
+		.vco			= 0x18,
+		.chk_shift		= 0x87,
+		.core_sel		= 0x0fff0100,
+		.int_st			= BIT(0),
+		.ctl0			= 0x00540003,
+	},
+	{
+		.sw_id			= SVSB_GPU,
+		.type			= SVSB_HIGH,
+		.set_freq_pct		= svs_set_bank_freq_pct_v3,
+		.get_volts		= svs_get_bank_volts_v3,
+		.tzone_name		= "gpu1",
+		.volt_flags		= SVSB_REMOVE_DVTFIXED_VOLT |
+					  SVSB_MON_VOLT_IGNORE,
+		.mode_support		= SVSB_MODE_INIT02 | SVSB_MODE_MON,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 902000000,
+		.turn_freq_base		= 688000000,
+		.volt_step		= 6250,
+		.volt_base		= 400000,
+		.vmax			= 0x60,
+		.vmin			= 0x1a,
+		.age_config		= 0x555555,
+		.dc_config		= 0x1,
+		.dvt_fixed		= 0x6,
+		.vco			= 0x18,
+		.chk_shift		= 0x87,
+		.core_sel		= 0x0fff0101,
+		.int_st			= BIT(1),
+		.ctl0			= 0x00540003,
+		.tzone_htemp		= 85000,
+		.tzone_htemp_voffset	= 0,
+		.tzone_ltemp		= 25000,
+		.tzone_ltemp_voffset	= 7,
+	},
+};
+
 static struct svs_bank svs_mt8183_banks[] = {
 	{
 		.sw_id			= SVSB_CPU_LITTLE,

@@ -1856,6 +2302,16 @@ struct svs_platform_data {
 	int (*probe)(struct svs_platform *svsp);
 };
 
+static const struct svs_platform_data svs_mt8192_platform_data = {
+	.name = "mt8192-svs",
+	.banks = svs_mt8192_banks,
+	.efuse_parsing = svs_mt8192_efuse_parsing,
+	.irqflags = IRQF_TRIGGER_HIGH,
+	.regs = svs_regs_v2,
+	.bank_max = ARRAY_SIZE(svs_mt8192_banks),
+	.probe = svs_mt8192_platform_probe,
+};
+
 static const struct svs_platform_data svs_mt8183_platform_data = {
 	.name = "mt8183-svs",
 	.banks = svs_mt8183_banks,

@@ -1868,6 +2324,9 @@ static const struct svs_platform_data svs_mt8183_platform_data = {
 
 static const struct of_device_id svs_of_match[] = {
 	{
+		.compatible = "mediatek,mt8192-svs",
+		.data = &svs_mt8192_platform_data,
+	}, {
 		.compatible = "mediatek,mt8183-svs",
 		.data = &svs_mt8183_platform_data,
 	}, {