Cadence MACB/GEM support for ZynqMP SGMII
Subsystems (5)
v4 cover Cadence MACB/GEM support for ZynqMP SGMII
Changes to allow SGMII mode to work properly in the GEM driver on the Xilinx ZynqMP platform.
Changes since v3:
-more code formatting and error handling fixes
Changes since v2:
-fixed missing includes in DT binding example
-fixed phy_init and phy_power_on error handling/cleanup, moved phy_power_on to open rather than probe
Changes since v1:
-changed order of controller reset and PHY init as per suggestion -switched device reset to be optional
-updated bindings doc patch for switch to YAML
Robert Hancock (3):
dt-bindings: net: cdns,macb: added generic PHY and reset mappings for
ZynqMP
net: macb: Added ZynqMP-specific initialization
arm64: dts: zynqmp: Added GEM reset definitions
.../devicetree/bindings/net/cdns,macb.yaml | 56 +++++++++++++++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 8 +++ drivers/net/ethernet/cadence/macb.h | 4 ++ drivers/net/ethernet/cadence/macb_main.c | 63 ++++++++++++++++++- 4 files changed, 128 insertions(+), 3 deletions(-)
Signature · 1 line
2.31.1
PATCH v4 1/3 dt-bindings: net: cdns,macb: added generic PHY and reset mappings for ZynqMP
Updated macb DT binding documentation to reflect the phy-names, phys, resets, reset-names properties which are now used with ZynqMP GEM devices, and added a ZynqMP-specific DT example.
--- .../devicetree/bindings/net/cdns,macb.yaml | 56 +++++++++++++++++++ 1 file changed, 56 insertions(+)
Documentation/devicetree/bindings/net/cdns,macb.yaml +56 -0
@@ -81,6 +81,25 @@ properties: phy-handle: true + phys: + maxItems: 1 + + phy-names: + const: sgmii-phy + description: + Required with ZynqMP SoC when in SGMII mode. + Should reference PS-GTR generic PHY device for this controller + instance. See ZynqMP example. + + resets: + maxItems: 1 + description: + Recommended with ZynqMP, specify reset control for this + controller instance with zynqmp-reset driver. + + reset-names: + maxItems: 1 + fixed-link: true iommus:
@@ -157,3 +176,40 @@ examples: reset-gpios = <&pioE 6 1>; }; }; + + - | + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/power/xlnx-zynqmp-power.h> + #include <dt-bindings/reset/xlnx-zynqmp-resets.h> + #include <dt-bindings/phy/phy.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + gem1: ethernet@ff0c0000 { + compatible = "cdns,zynqmp-gem", "cdns,gem"; + interrupt-parent = <&gic>; + interrupts = <0 59 4>, <0 59 4>; + reg = <0x0 0xff0c0000 0x0 0x1000>; + clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>, + <&zynqmp_clk GEM1_TX>, <&zynqmp_clk GEM1_RX>, + <&zynqmp_clk GEM_TSU>; + clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; + #address-cells = <1>; + #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x875>; + power-domains = <&zynqmp_firmware PD_ETH_1>; + resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>; + reset-names = "gem1_rst"; + status = "okay"; + phy-mode = "sgmii"; + phy-names = "sgmii-phy"; + phys = <&psgtr 1 PHY_TYPE_SGMII 1 1>; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + };
Signature · 1 line
2.31.1
PATCH v4 2/3 net: macb: Added ZynqMP-specific initialization
In reply to Robert HancockThe GEM controllers on ZynqMP were missing some initialization steps which are required in some cases when using SGMII mode, which uses the PS-GTR transceivers managed by the phy-zynqmp driver.
The GEM core appears to need a hardware-level reset in order to work properly in SGMII mode in cases where the GT reference clock was not present at initial power-on. This can be done using a reset mapped to the zynqmp-reset driver in the device tree.
Also, when in SGMII mode, the GEM driver needs to ensure the PHY is initialized and powered on.
--- drivers/net/ethernet/cadence/macb.h | 4 ++ drivers/net/ethernet/cadence/macb_main.c | 63 ++++++++++++++++++++++-- 2 files changed, 64 insertions(+), 3 deletions(-)
drivers/net/ethernet/cadence/macb.h +4 -0
@@ -12,6 +12,7 @@#include <linux/ptp_clock_kernel.h> #include <linux/net_tstamp.h> #include <linux/interrupt.h> +#include <linux/phy/phy.h> #if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT ) || defined(CONFIG_MACB_USE_HWSTAMP )#define MACB_EXT_DESC
@@ -1291,6 +1292,9 @@ struct macb {u32 wol;struct macb_ptp_info *ptp_info;/* macb-ptp interface */ + +struct phy *sgmii_phy;/* for ZynqMP SGMII mode */ +#ifdef MACB_EXT_DESC uint8_t hw_dma_cap;#endif
drivers/net/ethernet/cadence/macb_main.c +60 -3
121 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH net-next v4 2/3] net: macb: Added ZynqMP-specific initialization
Quoted 11 lines · Robert Hancock
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
The GEM controllers on ZynqMP were missing some initialization steps which are required in some cases when using SGMII mode, which uses the PS-GTR transceivers managed by the phy-zynqmp driver.
The GEM core appears to need a hardware-level reset in order to work properly in SGMII mode in cases where the GT reference clock was not present at initial power-on. This can be done using a reset mapped to the zynqmp-reset driver in the device tree.
Quoted 4 lines
Also, when in SGMII mode, the GEM driver needs to ensure the PHY is initialized and powered on.
Signed-off-by Robert Hancock <[email protected]>
Quoted 163 lines
--- drivers/net/ethernet/cadence/macb.h | 4 ++ drivers/net/ethernet/cadence/macb_main.c | 63 ++++++++++++++++++++++-- 2 files changed, 64 insertions(+), 3 deletions(-)drivers/net/ethernet/cadence/macb.h +4
-0@@ -12,6 +12,7 @@#include <linux/ptp_clock_kernel.h> #include <linux/net_tstamp.h> #include <linux/interrupt.h> +#include <linux/phy/phy.h> #if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT ) || defined(CONFIG_MACB_USE_HWSTAMP )#define MACB_EXT_DESC @@ -1291,6 +1292,9 @@ struct macb {u32 wol;struct macb_ptp_info *ptp_info;/* macb-ptp interface */ + +struct phy *sgmii_phy;/* for ZynqMP SGMII mode */ +#ifdef MACB_EXT_DESC uint8_t hw_dma_cap;#endif drivers/net/ethernet/cadence/macb_main.c +60
-4@@ -34,7 +34,9 @@#include <linux/udp.h> #include <linux/tcp.h> #include <linux/iopoll.h> +#include <linux/phy/phy.h> #include <linux/pm_runtime.h> +#include <linux/reset.h> #include "macb.h" /* This structure is only used for MACB on SiFive FU540 devices */ @@ -2739,10 +2741,14 @@ static int macb_open(struct net_device *dev)macb_init_hw (bp); - err =macb_phylink_connect (bp); + err =phy_power_on (bp->sgmii_phy);if (err) goto reset_hw; + err =macb_phylink_connect (bp); +if (err) + goto phy_off; +netif_tx_start_all_queues (dev);if (bp->ptp_info)@@ -2750,6 +2756,9 @@ static int macb_open(struct net_device *dev)return 0 ; +phy_off: +phy_power_off (bp->sgmii_phy); + reset_hw:macb_reset_hw (bp);for (q =0 , queue = bp->queues; q < bp->num_queues; ++q, ++queue)@@ -2775,6 +2784,8 @@ static int macb_close(struct net_device *dev)phylink_stop (bp->phylink);phylink_disconnect_phy (bp->phylink); +phy_power_off (bp->sgmii_phy); +spin_lock_irqsave (&bp->lock, flags);macb_reset_hw (bp);netif_carrier_off (dev);@@ -4544,13 +4555,55 @@ static const struct macb_config np4_config = { .usrio = &macb_default_usrio, }; +static int zynqmp_init (struct platform_device *pdev) +{ +struct net_device *dev =platform_get_drvdata (pdev); +struct macb *bp =netdev_priv (dev); +int ret; + +if (bp->phy_interface ==PHY_INTERFACE_MODE_SGMII ) { +/* Ensure PS-GTR PHY device used in SGMII mode is ready */ + bp->sgmii_phy =devm_phy_get (&pdev->dev,"sgmii-phy" ); + +if (IS_ERR (bp->sgmii_phy)) { + ret =PTR_ERR (bp->sgmii_phy); +dev_err_probe (&pdev->dev, ret, +"failed to get PS-GTR PHY\n" ); +return ret; + } + + ret =phy_init (bp->sgmii_phy); +if (ret) { +dev_err (&pdev->dev,"failed to init PS-GTR PHY: %d\n" , + ret); +return ret; + } + } + +/* Fully reset GEM controller at hardware level using zynqmp-reset driver, +* if mapped in device tree. +*/ + ret =device_reset_optional (&pdev->dev); +if (ret) { +dev_err_probe (&pdev->dev, ret,"failed to reset controller" ); +phy_exit (bp->sgmii_phy); +return ret; + } + + ret =macb_init (pdev); +if (ret) +phy_exit (bp->sgmii_phy); + +return ret; +} +static const struct macb_config zynqmp_config = { .caps =MACB_CAPS_GIGABIT_MODE_AVAILABLE |MACB_CAPS_JUMBO |MACB_CAPS_GEM_HAS_PTP |MACB_CAPS_BD_RD_PREFETCH , .dma_burst_length =16 , .clk_init = macb_clk_init, - .init = macb_init, + .init = zynqmp_init, .jumbo_max_len =10240 , .usrio = &macb_default_usrio, };@@ -4767,7 +4820,7 @@ static int macb_probe(struct platform_device *pdev) err =macb_mii_init (bp);if (err) - goto err_out_free_netdev; + goto err_out_phy_exit;netif_carrier_off (dev);@@ -4792,6 +4845,9 @@ static int macb_probe(struct platform_device *pdev)mdiobus_unregister (bp->mii_bus);mdiobus_free (bp->mii_bus); +err_out_phy_exit: +phy_exit (bp->sgmii_phy); + err_out_free_netdev:free_netdev (dev);@@ -4813,6 +4869,7 @@ static int macb_remove(struct platform_device *pdev)if (dev) { bp =netdev_priv (dev); +phy_exit (bp->sgmii_phy);mdiobus_unregister (bp->mii_bus);mdiobus_free (bp->mii_bus); --2.31.1
PATCH v4 3/3 arm64: dts: zynqmp: Added GEM reset definitions
In reply to Robert HancockThe Cadence GEM/MACB driver now utilizes the platform-level reset on the ZynqMP platform. Add reset definitions to the ZynqMP platform device tree to allow this to be used.
--- arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/xilinx/zynqmp.dtsi +8 -0
@@ -512,6 +512,8 @@ gem0: ethernet@ff0b0000 { #stream-id-cells = <1>; iommus = <&smmu 0x874>; power-domains = <&zynqmp_firmware PD_ETH_0>; + resets = <&zynqmp_reset ZYNQMP_RESET_GEM0>; + reset-names = "gem0_rst"; }; gem1: ethernet@ff0c0000 {
@@ -526,6 +528,8 @@ gem1: ethernet@ff0c0000 { #stream-id-cells = <1>; iommus = <&smmu 0x875>; power-domains = <&zynqmp_firmware PD_ETH_1>; + resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>; + reset-names = "gem1_rst"; }; gem2: ethernet@ff0d0000 {
@@ -540,6 +544,8 @@ gem2: ethernet@ff0d0000 { #stream-id-cells = <1>; iommus = <&smmu 0x876>; power-domains = <&zynqmp_firmware PD_ETH_2>; + resets = <&zynqmp_reset ZYNQMP_RESET_GEM2>; + reset-names = "gem2_rst"; }; gem3: ethernet@ff0e0000 {
@@ -554,6 +560,8 @@ gem3: ethernet@ff0e0000 { #stream-id-cells = <1>; iommus = <&smmu 0x877>; power-domains = <&zynqmp_firmware PD_ETH_3>; + resets = <&zynqmp_reset ZYNQMP_RESET_GEM3>; + reset-names = "gem3_rst"; }; gpio: gpio@ff0a0000 {
Signature · 1 line
2.31.1
This series was applied to netdev/net-next.git (master) by David S. Miller <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (master) by David S. Miller <[email protected]>:
Quoted 11 lines · On Thu, 27 Jan 2022 10:37:33 -0600 you wrote:
Changes to allow SGMII mode to work properly in the GEM driver on the Xilinx ZynqMP platform.
Changes since v3:
-more code formatting and error handling fixesChanges since v2:
(quoted diff) +0
-2-fixed missing includes in DT binding example -fixed phy_init and phy_power_on error handling/cleanup, moved
phy_power_onto open rather than probe
Quoted 1 line
[...]
Here is the summary with links:
- [net-next,v4,1/3] dt-bindings: net: cdns,macb: added generic PHY and reset mappings for ZynqMP
https://git.kernel.org/netdev/net-next/c/f4ea385a16c5 - [net-next,v4,2/3] net: macb: Added ZynqMP-specific initialization https://git.kernel.org/netdev/net-next/c/8b73fa3ae02b - [net-next,v4,3/3] arm64: dts: zynqmp: Added GEM reset definitions https://git.kernel.org/netdev/net-next/c/e461bd6f43f4
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html