Skip to contentSkip to conversation

6.0.16-rc1 review

PATCH In review Greg Kroah-Hartman 14 participants 1,086 messages Dec 28, 2022 – Dec 30, 2022 Page 3 of 8

Subsystems (13)
lore
Share & tools
lore
author maintainer
#245 lore raw

PATCH 245/1073 can: kvaser_usb_leaf: Fix improved state not being reported

In reply to Greg Kroah-Hartman

From: Anssi Hannula <[email protected]>

[ Upstream commit 8d21f5927ae604881f98587fabf6753f88730968 ]

The tested 0bfd:0017 Kvaser Memorator Professional HS/HS FW 2.0.50 and 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 do not seem to send any unsolicited events when error counters decrease or when the device transitions from ERROR_PASSIVE to ERROR_ACTIVE (or WARNING).

This causes the interface to e.g. indefinitely stay in the ERROR_PASSIVE state.

Fix that by asking for chip state (inc. counters) event every 0.5 secs when error counters are non-zero.

Since there are non-error-counter devices, also always poll in ERROR_PASSIVE even if the counters show zero.

---
 drivers/net/can/usb/kvaser_usb/kvaser_usb.h   |  7 +++
 .../net/can/usb/kvaser_usb/kvaser_usb_core.c  | 19 +++++-
 .../net/can/usb/kvaser_usb/kvaser_usb_leaf.c  | 58 +++++++++++++++++++
 3 files changed, 81 insertions(+), 3 deletions(-)
drivers/net/can/usb/kvaser_usb/kvaser_usb.h +7 -0
index f6c0938027ec..d9c5dd5da908 100644
@@ -104,6 +104,9 @@ struct kvaser_usb_net_priv {
 	struct can_priv can;
 	struct can_berr_counter bec;
 
+	/* subdriver-specific data */
+	void *sub_priv;
+
 	struct kvaser_usb *dev;
 	struct net_device *netdev;
 	int channel;
@@ -125,6 +128,8 @@ struct kvaser_usb_net_priv {
  *
  * @dev_setup_endpoints:	setup USB in and out endpoints
  * @dev_init_card:		initialize card
+ * @dev_init_channel:		initialize channel
+ * @dev_remove_channel:		uninitialize channel
  * @dev_get_software_info:	get software info
  * @dev_get_software_details:	get software details
  * @dev_get_card_info:		get card info
@@ -146,6 +151,8 @@ struct kvaser_usb_dev_ops {
 				    struct can_berr_counter *bec);
 	int (*dev_setup_endpoints)(struct kvaser_usb *dev);
 	int (*dev_init_card)(struct kvaser_usb *dev);
+	int (*dev_init_channel)(struct kvaser_usb_net_priv *priv);
+	void (*dev_remove_channel)(struct kvaser_usb_net_priv *priv);
 	int (*dev_get_software_info)(struct kvaser_usb *dev);
 	int (*dev_get_software_details)(struct kvaser_usb *dev);
 	int (*dev_get_card_info)(struct kvaser_usb *dev);
drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c +16 -3
index 802e27c0eced..0ebdfb77c50f 100644
@@ -684,6 +684,7 @@ static const struct ethtool_ops kvaser_usb_ethtool_ops_hwts = {
 
 static void kvaser_usb_remove_interfaces(struct kvaser_usb *dev)
 {
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
 	int i;
 
 	for (i = 0; i < dev->nchannels; i++) {
@@ -699,6 +700,9 @@ static void kvaser_usb_remove_interfaces(struct kvaser_usb *dev)
 		if (!dev->nets[i])
 			continue;
 
+		if (ops->dev_remove_channel)
+			ops->dev_remove_channel(dev->nets[i]);
+
 		free_candev(dev->nets[i]->netdev);
 	}
 }
@@ -772,17 +776,26 @@ static int kvaser_usb_init_one(struct kvaser_usb *dev, int channel)
 
 	dev->nets[channel] = priv;
 
+	if (ops->dev_init_channel) {
+		err = ops->dev_init_channel(priv);
+		if (err)
+			goto err;
+	}
+
 	err = register_candev(netdev);
 	if (err) {
 		dev_err(&dev->intf->dev, "Failed to register CAN device\n");
-		free_candev(netdev);
-		dev->nets[channel] = NULL;
-		return err;
+		goto err;
 	}
 
 	netdev_dbg(netdev, "device registered\n");
 
 	return 0;
+
+err:
+	free_candev(netdev);
+	dev->nets[channel] = NULL;
+	return err;
 }
 
 static int kvaser_usb_probe(struct usb_interface *intf,
drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c +58 -0

122 lines not on this page · raw message

Signature · 1 line
2.35.1
author maintainer
#246 lore raw

PATCH 246/1073 can: kvaser_usb_leaf: Fix wrong CAN state after stopping

In reply to Greg Kroah-Hartman

From: Anssi Hannula <[email protected]>

[ Upstream commit a11249acf802341294557895d8e5f6aef080253f ]

0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 sends a CMD_CHIP_STATE_EVENT indicating bus-off after stopping the device, causing a stopped device to appear as CAN_STATE_BUS_OFF instead of CAN_STATE_STOPPED.

Fix that by not handling error events on stopped devices.

---
 drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c +4 -0
index 993fcc19637d..4f9c76f4d0da 100644
@@ -1045,6 +1045,10 @@ static void kvaser_usb_leaf_rx_error(const struct kvaser_usb *dev,
 	leaf = priv->sub_priv;
 	stats = &priv->netdev->stats;
 
+	/* Ignore e.g. state change to bus-off reported just after stopping */
+	if (!netif_running(priv->netdev))
+		return;
+
 	/* Update all of the CAN interface's state and error counters before
 	 * trying any memory allocation that can actually fail with -ENOMEM.
 	 *
Signature · 1 line
2.35.1
author maintainer
#247 lore raw

PATCH 247/1073 can: kvaser_usb_leaf: Fix bogus restart events

In reply to Greg Kroah-Hartman

From: Anssi Hannula <[email protected]>

[ Upstream commit 90904d326269a38fe5dd895fb2db7c03199654c4 ]

When auto-restart is enabled, the kvaser_usb_leaf driver considers transition from any state >= CAN_STATE_BUS_OFF as a bus-off recovery event (restart).

However, these events may occur at interface startup time before kvaser_usb_open() has set the state to CAN_STATE_ERROR_ACTIVE, causing restarts counter to increase and CAN_ERR_RESTARTED to be sent despite no actual restart having occurred.

Fix that by making the auto-restart condition checks more strict so that they only trigger when the interface was actually in the BUS_OFF state.

---
 drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c +3 -3
index 4f9c76f4d0da..fa940be4e1b0 100644
@@ -898,7 +898,7 @@ static void kvaser_usb_leaf_tx_acknowledge(const struct kvaser_usb *dev,
 	context = &priv->tx_contexts[tid % dev->max_tx_urbs];
 
 	/* Sometimes the state change doesn't come after a bus-off event */
-	if (priv->can.restart_ms && priv->can.state >= CAN_STATE_BUS_OFF) {
+	if (priv->can.restart_ms && priv->can.state == CAN_STATE_BUS_OFF) {
 		struct sk_buff *skb;
 		struct can_frame *cf;
 
@@ -998,7 +998,7 @@ kvaser_usb_leaf_rx_error_update_can_state(struct kvaser_usb_net_priv *priv,
 	}
 
 	if (priv->can.restart_ms &&
-	    cur_state >= CAN_STATE_BUS_OFF &&
+	    cur_state == CAN_STATE_BUS_OFF &&
 	    new_state < CAN_STATE_BUS_OFF)
 		priv->can.can_stats.restarts++;
 
@@ -1088,7 +1088,7 @@ static void kvaser_usb_leaf_rx_error(const struct kvaser_usb *dev,
 		}
 
 		if (priv->can.restart_ms &&
-		    old_state >= CAN_STATE_BUS_OFF &&
+		    old_state == CAN_STATE_BUS_OFF &&
 		    new_state < CAN_STATE_BUS_OFF) {
 			cf->can_id |= CAN_ERR_RESTARTED;
 			netif_carrier_on(priv->netdev);
Signature · 1 line
2.35.1
author maintainer
#248 lore raw

PATCH 248/1073 can: kvaser_usb: Add struct kvaser_usb_busparams

In reply to Greg Kroah-Hartman

From: Jimmy Assarsson <[email protected]>

[ Upstream commit 00e5786177649c1e3110f9454fdd34e336597265 ]

Add struct kvaser_usb_busparams containing the busparameters used in CMD_{SET,GET}_BUSPARAMS* commands.

Stable-dep-of: 39d3df6b0ea8 ("can: kvaser_usb: Compare requested bittiming parameters with actual parameters in do_set_{,data}_bittiming")

---
 drivers/net/can/usb/kvaser_usb/kvaser_usb.h   |  8 +++++
 .../net/can/usb/kvaser_usb/kvaser_usb_hydra.c | 32 +++++++------------
 .../net/can/usb/kvaser_usb/kvaser_usb_leaf.c  | 18 ++++-------
 3 files changed, 27 insertions(+), 31 deletions(-)
drivers/net/can/usb/kvaser_usb/kvaser_usb.h +8 -0
index d9c5dd5da908..778b61c90c2b 100644
@@ -76,6 +76,14 @@ struct kvaser_usb_tx_urb_context {
 	u32 echo_index;
 };
 
+struct kvaser_usb_busparams {
+	__le32 bitrate;
+	u8 tseg1;
+	u8 tseg2;
+	u8 sjw;
+	u8 nsamples;
+} __packed;
+
 struct kvaser_usb {
 	struct usb_device *udev;
 	struct usb_interface *intf;
drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c +12 -20
index 3abfaa77e893..b8ae29872217 100644
@@ -196,17 +196,9 @@ struct kvaser_cmd_chip_state_event {
 #define KVASER_USB_HYDRA_BUS_MODE_CANFD_ISO	0x01
 #define KVASER_USB_HYDRA_BUS_MODE_NONISO	0x02
 struct kvaser_cmd_set_busparams {
-	__le32 bitrate;
-	u8 tseg1;
-	u8 tseg2;
-	u8 sjw;
-	u8 nsamples;
+	struct kvaser_usb_busparams busparams_arb;
 	u8 reserved0[4];
-	__le32 bitrate_d;
-	u8 tseg1_d;
-	u8 tseg2_d;
-	u8 sjw_d;
-	u8 nsamples_d;
+	struct kvaser_usb_busparams busparams_data;
 	u8 canfd_mode;
 	u8 reserved1[7];
 } __packed;
@@ -1538,11 +1530,11 @@ static int kvaser_usb_hydra_set_bittiming(struct net_device *netdev)
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_SET_BUSPARAMS_REQ;
-	cmd->set_busparams_req.bitrate = cpu_to_le32(bt->bitrate);
-	cmd->set_busparams_req.sjw = (u8)sjw;
-	cmd->set_busparams_req.tseg1 = (u8)tseg1;
-	cmd->set_busparams_req.tseg2 = (u8)tseg2;
-	cmd->set_busparams_req.nsamples = 1;
+	cmd->set_busparams_req.busparams_arb.bitrate = cpu_to_le32(bt->bitrate);
+	cmd->set_busparams_req.busparams_arb.sjw = (u8)sjw;
+	cmd->set_busparams_req.busparams_arb.tseg1 = (u8)tseg1;
+	cmd->set_busparams_req.busparams_arb.tseg2 = (u8)tseg2;
+	cmd->set_busparams_req.busparams_arb.nsamples = 1;
 
 	kvaser_usb_hydra_set_cmd_dest_he
 		(cmd, dev->card_data.hydra.channel_to_he[priv->channel]);
@@ -1572,11 +1564,11 @@ static int kvaser_usb_hydra_set_data_bittiming(struct net_device *netdev)
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_SET_BUSPARAMS_FD_REQ;
-	cmd->set_busparams_req.bitrate_d = cpu_to_le32(dbt->bitrate);
-	cmd->set_busparams_req.sjw_d = (u8)sjw;
-	cmd->set_busparams_req.tseg1_d = (u8)tseg1;
-	cmd->set_busparams_req.tseg2_d = (u8)tseg2;
-	cmd->set_busparams_req.nsamples_d = 1;
+	cmd->set_busparams_req.busparams_data.bitrate = cpu_to_le32(dbt->bitrate);
+	cmd->set_busparams_req.busparams_data.sjw = (u8)sjw;
+	cmd->set_busparams_req.busparams_data.tseg1 = (u8)tseg1;
+	cmd->set_busparams_req.busparams_data.tseg2 = (u8)tseg2;
+	cmd->set_busparams_req.busparams_data.nsamples = 1;
 
 	if (priv->can.ctrlmode & CAN_CTRLMODE_FD) {
 		if (priv->can.ctrlmode & CAN_CTRLMODE_FD_NON_ISO)
drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c +7 -11
index fa940be4e1b0..996d58b97af1 100644
@@ -164,11 +164,7 @@ struct usbcan_cmd_softinfo {
 struct kvaser_cmd_busparams {
 	u8 tid;
 	u8 channel;
-	__le32 bitrate;
-	u8 tseg1;
-	u8 tseg2;
-	u8 sjw;
-	u8 no_samp;
+	struct kvaser_usb_busparams busparams;
 } __packed;
 
 struct kvaser_cmd_tx_can {
@@ -1699,15 +1695,15 @@ static int kvaser_usb_leaf_set_bittiming(struct net_device *netdev)
 	cmd->len = CMD_HEADER_LEN + sizeof(struct kvaser_cmd_busparams);
 	cmd->u.busparams.channel = priv->channel;
 	cmd->u.busparams.tid = 0xff;
-	cmd->u.busparams.bitrate = cpu_to_le32(bt->bitrate);
-	cmd->u.busparams.sjw = bt->sjw;
-	cmd->u.busparams.tseg1 = bt->prop_seg + bt->phase_seg1;
-	cmd->u.busparams.tseg2 = bt->phase_seg2;
+	cmd->u.busparams.busparams.bitrate = cpu_to_le32(bt->bitrate);
+	cmd->u.busparams.busparams.sjw = bt->sjw;
+	cmd->u.busparams.busparams.tseg1 = bt->prop_seg + bt->phase_seg1;
+	cmd->u.busparams.busparams.tseg2 = bt->phase_seg2;
 
 	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
-		cmd->u.busparams.no_samp = 3;
+		cmd->u.busparams.busparams.nsamples = 3;
 	else
-		cmd->u.busparams.no_samp = 1;
+		cmd->u.busparams.busparams.nsamples = 1;
 
 	rc = kvaser_usb_send_cmd(dev, cmd, cmd->len);
 
Signature · 1 line
2.35.1
author maintainer
#249 lore raw

PATCH 249/1073 can: kvaser_usb: Compare requested bittiming parameters with actual parameters in do_set_{,data}_bittiming

In reply to Greg Kroah-Hartman

From: Jimmy Assarsson <[email protected]>

[ Upstream commit 39d3df6b0ea80f9b515c632ca07b39b1c156edee ]

The device will respond with a CMD_ERROR_EVENT command, with error_code KVASER_USB_{LEAF,HYDRA}_ERROR_EVENT_PARAM, if the CMD_SET_BUSPARAMS_REQ contains invalid bittiming parameters.
However, this command does not contain any channel reference.

To check if the CMD_SET_BUSPARAMS_REQ was successful, redback and compare the requested bittiming parameters with the device reported parameters.

Fixes 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
---
 drivers/net/can/usb/kvaser_usb/kvaser_usb.h   |  15 +-
 .../net/can/usb/kvaser_usb/kvaser_usb_core.c  |  96 ++++++++++-
 .../net/can/usb/kvaser_usb/kvaser_usb_hydra.c | 150 +++++++++++++++---
 .../net/can/usb/kvaser_usb/kvaser_usb_leaf.c  |  64 ++++++--
 4 files changed, 284 insertions(+), 41 deletions(-)
drivers/net/can/usb/kvaser_usb/kvaser_usb.h +12 -3
index 778b61c90c2b..ff10b3790d84 100644
@@ -119,9 +119,12 @@ struct kvaser_usb_net_priv {
 	struct net_device *netdev;
 	int channel;
 
-	struct completion start_comp, stop_comp, flush_comp;
+	struct completion start_comp, stop_comp, flush_comp,
+			  get_busparams_comp;
 	struct usb_anchor tx_submitted;
 
+	struct kvaser_usb_busparams busparams_nominal, busparams_data;
+
 	spinlock_t tx_contexts_lock; /* lock for active_tx_contexts */
 	int active_tx_contexts;
 	struct kvaser_usb_tx_urb_context tx_contexts[];
@@ -131,7 +134,9 @@ struct kvaser_usb_net_priv {
  * struct kvaser_usb_dev_ops - Device specific functions
  * @dev_set_mode:		used for can.do_set_mode
  * @dev_set_bittiming:		used for can.do_set_bittiming
+ * @dev_get_busparams:		readback arbitration busparams
  * @dev_set_data_bittiming:	used for can.do_set_data_bittiming
+ * @dev_get_data_busparams:	readback data busparams
  * @dev_get_berr_counter:	used for can.do_get_berr_counter
  *
  * @dev_setup_endpoints:	setup USB in and out endpoints
@@ -153,8 +158,12 @@ struct kvaser_usb_net_priv {
  */
 struct kvaser_usb_dev_ops {
 	int (*dev_set_mode)(struct net_device *netdev, enum can_mode mode);
-	int (*dev_set_bittiming)(struct net_device *netdev);
-	int (*dev_set_data_bittiming)(struct net_device *netdev);
+	int (*dev_set_bittiming)(const struct net_device *netdev,
+				 const struct kvaser_usb_busparams *busparams);
+	int (*dev_get_busparams)(struct kvaser_usb_net_priv *priv);
+	int (*dev_set_data_bittiming)(const struct net_device *netdev,
+				      const struct kvaser_usb_busparams *busparams);
+	int (*dev_get_data_busparams)(struct kvaser_usb_net_priv *priv);
 	int (*dev_get_berr_counter)(const struct net_device *netdev,
 				    struct can_berr_counter *bec);
 	int (*dev_setup_endpoints)(struct kvaser_usb *dev);
drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c +90 -6

126 lines not on this page · raw message

drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c +129 -21

240 lines not on this page · raw message

drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c +53 -11

115 lines not on this page · raw message

Signature · 1 line
2.35.1
author maintainer
#250 lore raw

PATCH 250/1073 clk: renesas: r8a779a0: Fix SD0H clock name

In reply to Greg Kroah-Hartman

From: Wolfram Sang <[email protected]>

[ Upstream commit db7076d5a7f0ca7dcf08f5095c74f86d4d0085ff ]

Correct the misspelled textual name of the SD0H clock.

Fixes 470e3f0d0b15 ("clk: renesas: rcar-gen4: Introduce R-Car Gen4 CPG driver")
---
 drivers/clk/renesas/r8a779a0-cpg-mssr.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/renesas/r8a779a0-cpg-mssr.c +1 -1
index d74d46833012..e02542ca24a0 100644
@@ -116,7 +116,7 @@ static const struct cpg_core_clk r8a779a0_core_clks[] __initconst = {
 	DEF_FIXED("cp",		R8A779A0_CLK_CP,	CLK_EXTAL,	2, 1),
 	DEF_FIXED("cl16mck",	R8A779A0_CLK_CL16MCK,	CLK_PLL1_DIV2,	64, 1),
 
-	DEF_GEN4_SDH("sdh0",	R8A779A0_CLK_SD0H,	CLK_SDSRC,	   0x870),
+	DEF_GEN4_SDH("sd0h",	R8A779A0_CLK_SD0H,	CLK_SDSRC,	   0x870),
 	DEF_GEN4_SD("sd0",	R8A779A0_CLK_SD0,	R8A779A0_CLK_SD0H, 0x870),
 
 	DEF_BASE("rpc",		R8A779A0_CLK_RPC, CLK_TYPE_GEN4_RPC, CLK_RPCSRC),
Signature · 1 line
2.35.1
author maintainer
#251 lore raw

PATCH 252/1073 drm/i915/guc: Add a helper for log buffer size

In reply to Greg Kroah-Hartman

From: Alan Previn <[email protected]>

[ Upstream commit 5ce27d6210018e972197ff7e5da6309f919fd61b ]

Add a helper to get GuC log buffer size.

Stable-dep-of: befb231d5de2 ("drm/i915/guc: Fix GuC error capture sizing estimation and reporting")

---
 drivers/gpu/drm/i915/gt/uc/intel_guc_log.c | 49 ++++++++++++----------
 1 file changed, 27 insertions(+), 22 deletions(-)
drivers/gpu/drm/i915/gt/uc/intel_guc_log.c +27 -22
index 25b2d7ce6640..492bbf419d4d 100644
@@ -15,6 +15,32 @@
 
 static void guc_log_copy_debuglogs_for_relay(struct intel_guc_log *log);
 
+static u32 intel_guc_log_size(struct intel_guc_log *log)
+{
+	/*
+	 *  GuC Log buffer Layout:
+	 *
+	 *  NB: Ordering must follow "enum guc_log_buffer_type".
+	 *
+	 *  +===============================+ 00B
+	 *  |      Debug state header       |
+	 *  +-------------------------------+ 32B
+	 *  |    Crash dump state header    |
+	 *  +-------------------------------+ 64B
+	 *  |     Capture state header      |
+	 *  +-------------------------------+ 96B
+	 *  |                               |
+	 *  +===============================+ PAGE_SIZE (4KB)
+	 *  |          Debug logs           |
+	 *  +===============================+ + DEBUG_SIZE
+	 *  |        Crash Dump logs        |
+	 *  +===============================+ + CRASH_SIZE
+	 *  |         Capture logs          |
+	 *  +===============================+ + CAPTURE_SIZE
+	 */
+	return PAGE_SIZE + CRASH_BUFFER_SIZE + DEBUG_BUFFER_SIZE + CAPTURE_BUFFER_SIZE;
+}
+
 /**
  * DOC: GuC firmware log
  *
@@ -461,32 +487,11 @@ int intel_guc_log_create(struct intel_guc_log *log)
 
 	GEM_BUG_ON(log->vma);
 
-	/*
-	 *  GuC Log buffer Layout
-	 * (this ordering must follow "enum guc_log_buffer_type" definition)
-	 *
-	 *  +===============================+ 00B
-	 *  |      Debug state header       |
-	 *  +-------------------------------+ 32B
-	 *  |    Crash dump state header    |
-	 *  +-------------------------------+ 64B
-	 *  |     Capture state header      |
-	 *  +-------------------------------+ 96B
-	 *  |                               |
-	 *  +===============================+ PAGE_SIZE (4KB)
-	 *  |          Debug logs           |
-	 *  +===============================+ + DEBUG_SIZE
-	 *  |        Crash Dump logs        |
-	 *  +===============================+ + CRASH_SIZE
-	 *  |         Capture logs          |
-	 *  +===============================+ + CAPTURE_SIZE
-	 */
 	if (intel_guc_capture_output_min_size_est(guc) > CAPTURE_BUFFER_SIZE)
 		DRM_WARN("GuC log buffer for state_capture maybe too small. %d < %d\n",
 			 CAPTURE_BUFFER_SIZE, intel_guc_capture_output_min_size_est(guc));
 
-	guc_log_size = PAGE_SIZE + CRASH_BUFFER_SIZE + DEBUG_BUFFER_SIZE +
-		       CAPTURE_BUFFER_SIZE;
+	guc_log_size = intel_guc_log_size(log);
 
 	vma = intel_guc_allocate_vma(guc, guc_log_size);
 	if (IS_ERR(vma)) {
Signature · 1 line
2.35.1
author maintainer
#252 lore raw

PATCH 253/1073 drm/i915/guc: Fix capture size warning and bump the size

In reply to Greg Kroah-Hartman

From: John Harrison <[email protected]>

[ Upstream commit 56c7f0e2026328e56106b54cb0e2fe3a7e70ce4f ]

There was a size check to warn if the GuC error state capture buffer allocation would be too small to fit a reasonable amount of capture data for the current platform. Unfortunately, the test was done too early in the boot sequence and was actually testing 'if(-ENODEV > size)'.

Move the check to be later. The check is only used to print a warning message, so it doesn't really matter how early or late it is done. Note that it is not possible to dynamically size the buffer because the allocation needs to be done before the engine information is available (at least, it would be in the intended two-phase GuC init process).

Now that the check works, it is reporting size too small for newer platforms. The check includes a 3x oversample multiplier to allow for multiple error captures to be bufferd by GuC before i915 has a chance to read them out. This is less important than simply being big enough to fit the first capture.

So a) bump the default size to be large enough for one capture minimum and b) make the warning only if one capture won't fit, instead use a notice for the 3x size.

Note that the size estimate is a worst case scenario. Actual captures will likely be smaller.

Lastly, use drm_warn istead of DRM_WARN as the former provides more infmration and the latter is deprecated.

Stable-dep-of: befb231d5de2 ("drm/i915/guc: Fix GuC error capture sizing estimation and reporting")

---
 .../gpu/drm/i915/gt/uc/intel_guc_capture.c    | 40 ++++++++++++++-----
 .../gpu/drm/i915/gt/uc/intel_guc_capture.h    |  1 -
 drivers/gpu/drm/i915/gt/uc/intel_guc_log.c    |  4 --
 drivers/gpu/drm/i915/gt/uc/intel_guc_log.h    |  4 +-
 4 files changed, 31 insertions(+), 18 deletions(-)
drivers/gpu/drm/i915/gt/uc/intel_guc_capture.c +29 -11
index 75257bd20ff0..b54b7883320b 100644
@@ -600,10 +600,8 @@ intel_guc_capture_getnullheader(struct intel_guc *guc,
 	return 0;
 }
 
-#define GUC_CAPTURE_OVERBUFFER_MULTIPLIER 3
-
-int
-intel_guc_capture_output_min_size_est(struct intel_guc *guc)
+static int
+guc_capture_output_min_size_est(struct intel_guc *guc)
 {
 	struct intel_gt *gt = guc_to_gt(guc);
 	struct intel_engine_cs *engine;
@@ -623,13 +621,8 @@ intel_guc_capture_output_min_size_est(struct intel_guc *guc)
 	 * For each engine instance, there would be 1 x guc_state_capture_group_t output
 	 * followed by 3 x guc_state_capture_t lists. The latter is how the register
 	 * dumps are split across different register types (where the '3' are global vs class
-	 * vs instance). Finally, let's multiply the whole thing by 3x (just so we are
-	 * not limited to just 1 round of data in a worst case full register dump log)
-	 *
-	 * NOTE: intel_guc_log that allocates the log buffer would round this size up to
-	 * a power of two.
+	 * vs instance).
 	 */
-
 	for_each_engine(engine, gt, id) {
 		worst_min_size += sizeof(struct guc_state_capture_group_header_t) +
 					 (3 * sizeof(struct guc_state_capture_header_t));
@@ -649,7 +642,30 @@ intel_guc_capture_output_min_size_est(struct intel_guc *guc)
 
 	worst_min_size += (num_regs * sizeof(struct guc_mmio_reg));
 
-	return (worst_min_size * GUC_CAPTURE_OVERBUFFER_MULTIPLIER);
+	return worst_min_size;
+}
+
+/*
+ * Add on a 3x multiplier to allow for multiple back-to-back captures occurring
+ * before the i915 can read the data out and process it
+ */
+#define GUC_CAPTURE_OVERBUFFER_MULTIPLIER 3
+
+static void check_guc_capture_size(struct intel_guc *guc)
+{
+	struct drm_i915_private *i915 = guc_to_gt(guc)->i915;
+	int min_size = guc_capture_output_min_size_est(guc);
+	int spare_size = min_size * GUC_CAPTURE_OVERBUFFER_MULTIPLIER;
+
+	if (min_size < 0)
+		drm_warn(&i915->drm, "Failed to calculate GuC error state capture buffer minimum size: %d!\n",
+			 min_size);
+	else if (min_size > CAPTURE_BUFFER_SIZE)
+		drm_warn(&i915->drm, "GuC error state capture buffer is too small: %d < %d\n",
+			 CAPTURE_BUFFER_SIZE, min_size);
+	else if (spare_size > CAPTURE_BUFFER_SIZE)
+		drm_notice(&i915->drm, "GuC error state capture buffer maybe too small: %d < %d (min = %d)\n",
+			   CAPTURE_BUFFER_SIZE, spare_size, min_size);
 }
 
 /*
@@ -1580,5 +1596,7 @@ int intel_guc_capture_init(struct intel_guc *guc)
 	INIT_LIST_HEAD(&guc->capture->outlist);
 	INIT_LIST_HEAD(&guc->capture->cachelist);
 
+	check_guc_capture_size(guc);
+
 	return 0;
 }
drivers/gpu/drm/i915/gt/uc/intel_guc_capture.h +0 -1
index d3d7bd0b6db6..fbd3713c7832 100644
@@ -21,7 +21,6 @@ int intel_guc_capture_print_engine_node(struct drm_i915_error_state_buf *m,
 void intel_guc_capture_get_matching_node(struct intel_gt *gt, struct intel_engine_coredump *ee,
 					 struct intel_context *ce);
 void intel_guc_capture_process(struct intel_guc *guc);
-int intel_guc_capture_output_min_size_est(struct intel_guc *guc);
 int intel_guc_capture_getlist(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
 			      void **outptr);
 int intel_guc_capture_getlistsize(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
drivers/gpu/drm/i915/gt/uc/intel_guc_log.c +0 -4
index 492bbf419d4d..991d4a02248d 100644
@@ -487,10 +487,6 @@ int intel_guc_log_create(struct intel_guc_log *log)
 
 	GEM_BUG_ON(log->vma);
 
-	if (intel_guc_capture_output_min_size_est(guc) > CAPTURE_BUFFER_SIZE)
-		DRM_WARN("GuC log buffer for state_capture maybe too small. %d < %d\n",
-			 CAPTURE_BUFFER_SIZE, intel_guc_capture_output_min_size_est(guc));
-
 	guc_log_size = intel_guc_log_size(log);
 
 	vma = intel_guc_allocate_vma(guc, guc_log_size);
drivers/gpu/drm/i915/gt/uc/intel_guc_log.h +2 -2
index 18007e639be9..dc9715411d62 100644
@@ -22,11 +22,11 @@ struct intel_guc;
 #elif defined(CONFIG_DRM_I915_DEBUG_GEM)
 #define CRASH_BUFFER_SIZE	SZ_1M
 #define DEBUG_BUFFER_SIZE	SZ_2M
-#define CAPTURE_BUFFER_SIZE	SZ_1M
+#define CAPTURE_BUFFER_SIZE	SZ_4M
 #else
 #define CRASH_BUFFER_SIZE	SZ_8K
 #define DEBUG_BUFFER_SIZE	SZ_64K
-#define CAPTURE_BUFFER_SIZE	SZ_16K
+#define CAPTURE_BUFFER_SIZE	SZ_2M
 #endif
 
 /*
Signature · 1 line
2.35.1
author maintainer
#253 lore raw

PATCH 254/1073 drm/i915/guc: Make GuC log sizes runtime configurable

In reply to Greg Kroah-Hartman

From: John Harrison <[email protected]>

[ Upstream commit 8ad0152afb1bb3878bba282308f037d73a87ace5 ]

The GuC log buffer sizes had to be configured statically at compile time. This can be quite troublesome when needing to get larger logs out of a released driver. So re-organise the code to allow a boot time module parameter override.

Stable-dep-of: befb231d5de2 ("drm/i915/guc: Fix GuC error capture sizing estimation and reporting")

---
 drivers/gpu/drm/i915/gt/uc/intel_guc.c        |  53 ++----
 .../gpu/drm/i915/gt/uc/intel_guc_capture.c    |  14 +-
 drivers/gpu/drm/i915/gt/uc/intel_guc_log.c    | 176 +++++++++++++++++-
 drivers/gpu/drm/i915/gt/uc/intel_guc_log.h    |  42 +++--
 drivers/gpu/drm/i915/i915_params.c            |  12 ++
 drivers/gpu/drm/i915/i915_params.h            |   3 +
 6 files changed, 226 insertions(+), 74 deletions(-)
drivers/gpu/drm/i915/gt/uc/intel_guc.c +11 -42
index 2706a8c65090..7fbcfeda9195 100644
@@ -224,53 +224,22 @@ static u32 guc_ctl_feature_flags(struct intel_guc *guc)
 
 static u32 guc_ctl_log_params_flags(struct intel_guc *guc)
 {
-	u32 offset = intel_guc_ggtt_offset(guc, guc->log.vma) >> PAGE_SHIFT;
-	u32 flags;
-
-	#if (((CRASH_BUFFER_SIZE) % SZ_1M) == 0)
-	#define LOG_UNIT SZ_1M
-	#define LOG_FLAG GUC_LOG_LOG_ALLOC_UNITS
-	#else
-	#define LOG_UNIT SZ_4K
-	#define LOG_FLAG 0
-	#endif
-
-	#if (((CAPTURE_BUFFER_SIZE) % SZ_1M) == 0)
-	#define CAPTURE_UNIT SZ_1M
-	#define CAPTURE_FLAG GUC_LOG_CAPTURE_ALLOC_UNITS
-	#else
-	#define CAPTURE_UNIT SZ_4K
-	#define CAPTURE_FLAG 0
-	#endif
-
-	BUILD_BUG_ON(!CRASH_BUFFER_SIZE);
-	BUILD_BUG_ON(!IS_ALIGNED(CRASH_BUFFER_SIZE, LOG_UNIT));
-	BUILD_BUG_ON(!DEBUG_BUFFER_SIZE);
-	BUILD_BUG_ON(!IS_ALIGNED(DEBUG_BUFFER_SIZE, LOG_UNIT));
-	BUILD_BUG_ON(!CAPTURE_BUFFER_SIZE);
-	BUILD_BUG_ON(!IS_ALIGNED(CAPTURE_BUFFER_SIZE, CAPTURE_UNIT));
-
-	BUILD_BUG_ON((CRASH_BUFFER_SIZE / LOG_UNIT - 1) >
-			(GUC_LOG_CRASH_MASK >> GUC_LOG_CRASH_SHIFT));
-	BUILD_BUG_ON((DEBUG_BUFFER_SIZE / LOG_UNIT - 1) >
-			(GUC_LOG_DEBUG_MASK >> GUC_LOG_DEBUG_SHIFT));
-	BUILD_BUG_ON((CAPTURE_BUFFER_SIZE / CAPTURE_UNIT - 1) >
-			(GUC_LOG_CAPTURE_MASK >> GUC_LOG_CAPTURE_SHIFT));
+	struct intel_guc_log *log = &guc->log;
+	u32 offset, flags;
+
+	GEM_BUG_ON(!log->sizes_initialised);
+
+	offset = intel_guc_ggtt_offset(guc, log->vma) >> PAGE_SHIFT;
 
 	flags = GUC_LOG_VALID |
 		GUC_LOG_NOTIFY_ON_HALF_FULL |
-		CAPTURE_FLAG |
-		LOG_FLAG |
-		((CRASH_BUFFER_SIZE / LOG_UNIT - 1) << GUC_LOG_CRASH_SHIFT) |
-		((DEBUG_BUFFER_SIZE / LOG_UNIT - 1) << GUC_LOG_DEBUG_SHIFT) |
-		((CAPTURE_BUFFER_SIZE / CAPTURE_UNIT - 1) << GUC_LOG_CAPTURE_SHIFT) |
+		log->sizes[GUC_LOG_SECTIONS_DEBUG].flag |
+		log->sizes[GUC_LOG_SECTIONS_CAPTURE].flag |
+		(log->sizes[GUC_LOG_SECTIONS_CRASH].count << GUC_LOG_CRASH_SHIFT) |
+		(log->sizes[GUC_LOG_SECTIONS_DEBUG].count << GUC_LOG_DEBUG_SHIFT) |
+		(log->sizes[GUC_LOG_SECTIONS_CAPTURE].count << GUC_LOG_CAPTURE_SHIFT) |
 		(offset << GUC_LOG_BUF_ADDR_SHIFT);
 
-	#undef LOG_UNIT
-	#undef LOG_FLAG
-	#undef CAPTURE_UNIT
-	#undef CAPTURE_FLAG
-
 	return flags;
 }
 
drivers/gpu/drm/i915/gt/uc/intel_guc_capture.c +8 -6
index b54b7883320b..d2ac53d4f3b6 100644
@@ -656,16 +656,17 @@ static void check_guc_capture_size(struct intel_guc *guc)
 	struct drm_i915_private *i915 = guc_to_gt(guc)->i915;
 	int min_size = guc_capture_output_min_size_est(guc);
 	int spare_size = min_size * GUC_CAPTURE_OVERBUFFER_MULTIPLIER;
+	u32 buffer_size = intel_guc_log_section_size_capture(&guc->log);
 
 	if (min_size < 0)
 		drm_warn(&i915->drm, "Failed to calculate GuC error state capture buffer minimum size: %d!\n",
 			 min_size);
-	else if (min_size > CAPTURE_BUFFER_SIZE)
+	else if (min_size > buffer_size)
 		drm_warn(&i915->drm, "GuC error state capture buffer is too small: %d < %d\n",
-			 CAPTURE_BUFFER_SIZE, min_size);
-	else if (spare_size > CAPTURE_BUFFER_SIZE)
+			 buffer_size, min_size);
+	else if (spare_size > buffer_size)
 		drm_notice(&i915->drm, "GuC error state capture buffer maybe too small: %d < %d (min = %d)\n",
-			   CAPTURE_BUFFER_SIZE, spare_size, min_size);
+			   buffer_size, spare_size, min_size);
 }
 
 /*
@@ -1294,7 +1295,8 @@ static void __guc_capture_process_output(struct intel_guc *guc)
 
 	log_buf_state = guc->log.buf_addr +
 			(sizeof(struct guc_log_buffer_state) * GUC_CAPTURE_LOG_BUFFER);
-	src_data = guc->log.buf_addr + intel_guc_get_log_buffer_offset(GUC_CAPTURE_LOG_BUFFER);
+	src_data = guc->log.buf_addr +
+		   intel_guc_get_log_buffer_offset(&guc->log, GUC_CAPTURE_LOG_BUFFER);
 
 	/*
 	 * Make a copy of the state structure, inside GuC log buffer
@@ -1302,7 +1304,7 @@ static void __guc_capture_process_output(struct intel_guc *guc)
 	 * from it multiple times.
 	 */
 	memcpy(&log_buf_state_local, log_buf_state, sizeof(struct guc_log_buffer_state));
-	buffer_size = intel_guc_get_log_buffer_size(GUC_CAPTURE_LOG_BUFFER);
+	buffer_size = intel_guc_get_log_buffer_size(&guc->log, GUC_CAPTURE_LOG_BUFFER);
 	read_offset = log_buf_state_local.read_ptr;
 	write_offset = log_buf_state_local.sampled_write_ptr;
 	full_count = log_buf_state_local.buffer_full_cnt;
drivers/gpu/drm/i915/gt/uc/intel_guc_log.c +166 -10

231 lines not on this page · raw message

drivers/gpu/drm/i915/gt/uc/intel_guc_log.h +26 -16

74 lines not on this page · raw message

drivers/gpu/drm/i915/i915_params.c +12 -0
index 6fc475a5db61..06ca5b822111 100644
@@ -171,6 +171,18 @@ i915_param_named(guc_log_level, int, 0400,
 	"GuC firmware logging level. Requires GuC to be loaded. "
 	"(-1=auto [default], 0=disable, 1..4=enable with verbosity min..max)");
 
+i915_param_named(guc_log_size_crash, int, 0400,
+	"GuC firmware logging buffer size for crash dumps (in MB)"
+	"(-1=auto [default], NB: max = 4, other restrictions apply)");
+
+i915_param_named(guc_log_size_debug, int, 0400,
+	"GuC firmware logging buffer size for debug logs (in MB)"
+	"(-1=auto [default], NB: max = 16, other restrictions apply)");
+
+i915_param_named(guc_log_size_capture, int, 0400,
+	"GuC error capture register dump buffer size (in MB)"
+	"(-1=auto [default], NB: max = 4, other restrictions apply)");
+
 i915_param_named_unsafe(guc_firmware_path, charp, 0400,
 	"GuC firmware path to use instead of the default one");
 
drivers/gpu/drm/i915/i915_params.h +3 -0
index 2733cb6cfe09..f684d1ab8707 100644
@@ -61,6 +61,9 @@ struct drm_printer;
 	param(int, invert_brightness, 0, 0600) \
 	param(int, enable_guc, -1, 0400) \
 	param(int, guc_log_level, -1, 0400) \
+	param(int, guc_log_size_crash, -1, 0400) \
+	param(int, guc_log_size_debug, -1, 0400) \
+	param(int, guc_log_size_capture, -1, 0400) \
 	param(char *, guc_firmware_path, NULL, 0400) \
 	param(char *, huc_firmware_path, NULL, 0400) \
 	param(char *, dmc_firmware_path, NULL, 0400) \
Signature · 1 line
2.35.1
author maintainer
#254 lore raw

PATCH 255/1073 drm/i915/guc: Add error-capture init warnings when needed

In reply to Greg Kroah-Hartman

From: Alan Previn <[email protected]>

[ Upstream commit a894077890ad118de88c97c03f67a611ca60882a ]

If GuC is being used and we initialized GuC-error-capture, we need to be warning if we don't provide an error-capture register list in the firmware ADS, for valid GT engines. A warning makes sense as this would impact debugability without realizing why a reglist wasn't retrieved and reported by GuC.

However, depending on the platform, we might have certain engines that have a register list for engine instance error state but not for engine class. Thus, add a check only to warn if the register list was non existent vs an empty list (use the empty lists to skip the warning).

NOTE: if a future platform were to introduce new registers in place of what was an empty list on existing / legacy hardware engines no warning is provided as the empty list is meant to be used intentionally. As an example, if a future hardware were to add blitter engine-class-registers (new) on top of the legacy blitter engine-instance-register (HEAD, TAIL, etc.), no warning is generated.

Stable-dep-of: befb231d5de2 ("drm/i915/guc: Fix GuC error capture sizing estimation and reporting")

---
 .../gpu/drm/i915/gt/uc/intel_guc_capture.c    | 78 ++++++++++++++++---
 1 file changed, 69 insertions(+), 9 deletions(-)
drivers/gpu/drm/i915/gt/uc/intel_guc_capture.c +69 -9
index d2ac53d4f3b6..c398bdd5403a 100644
@@ -419,6 +419,44 @@ guc_capture_get_device_reglist(struct intel_guc *guc)
 	return default_lists;
 }
 
+static const char *
+__stringify_type(u32 type)
+{
+	switch (type) {
+	case GUC_CAPTURE_LIST_TYPE_GLOBAL:
+		return "Global";
+	case GUC_CAPTURE_LIST_TYPE_ENGINE_CLASS:
+		return "Class";
+	case GUC_CAPTURE_LIST_TYPE_ENGINE_INSTANCE:
+		return "Instance";
+	default:
+		break;
+	}
+
+	return "unknown";
+}
+
+static const char *
+__stringify_engclass(u32 class)
+{
+	switch (class) {
+	case GUC_RENDER_CLASS:
+		return "Render";
+	case GUC_VIDEO_CLASS:
+		return "Video";
+	case GUC_VIDEOENHANCE_CLASS:
+		return "VideoEnhance";
+	case GUC_BLITTER_CLASS:
+		return "Blitter";
+	case GUC_COMPUTE_CLASS:
+		return "Compute";
+	default:
+		break;
+	}
+
+	return "unknown";
+}
+
 static int
 guc_capture_list_init(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
 		      struct guc_mmio_reg *ptr, u16 num_entries)
@@ -482,23 +520,38 @@ guc_cap_list_num_regs(struct intel_guc_state_capture *gc, u32 owner, u32 type, u
 	return num_regs;
 }
 
-int
-intel_guc_capture_getlistsize(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
-			      size_t *size)
+static int
+guc_capture_getlistsize(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
+			size_t *size, bool is_purpose_est)
 {
 	struct intel_guc_state_capture *gc = guc->capture;
+	struct drm_i915_private *i915 = guc_to_gt(guc)->i915;
 	struct __guc_capture_ads_cache *cache = &gc->ads_cache[owner][type][classid];
 	int num_regs;
 
-	if (!gc->reglists)
+	if (!gc->reglists) {
+		drm_warn(&i915->drm, "GuC-capture: No reglist on this device\n");
 		return -ENODEV;
+	}
 
 	if (cache->is_valid) {
 		*size = cache->size;
 		return cache->status;
 	}
 
+	if (!is_purpose_est && owner == GUC_CAPTURE_LIST_INDEX_PF &&
+	    !guc_capture_get_one_list(gc->reglists, owner, type, classid)) {
+		if (type == GUC_CAPTURE_LIST_TYPE_GLOBAL)
+			drm_warn(&i915->drm, "Missing GuC-Err-Cap reglist Global!\n");
+		else
+			drm_warn(&i915->drm, "Missing GuC-Err-Cap reglist %s(%u):%s(%u)!\n",
+				 __stringify_type(type), type,
+				 __stringify_engclass(classid), classid);
+		return -ENODATA;
+	}
+
 	num_regs = guc_cap_list_num_regs(gc, owner, type, classid);
+	/* intentional empty lists can exist depending on hw config */
 	if (!num_regs)
 		return -ENODATA;
 
@@ -508,6 +561,13 @@ intel_guc_capture_getlistsize(struct intel_guc *guc, u32 owner, u32 type, u32 cl
 	return 0;
 }
 
+int
+intel_guc_capture_getlistsize(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
+			      size_t *size)
+{
+	return guc_capture_getlistsize(guc, owner, type, classid, size, false);
+}
+
 static void guc_capture_create_prealloc_nodes(struct intel_guc *guc);
 
 int
@@ -627,15 +687,15 @@ guc_capture_output_min_size_est(struct intel_guc *guc)
 		worst_min_size += sizeof(struct guc_state_capture_group_header_t) +
 					 (3 * sizeof(struct guc_state_capture_header_t));
 
-		if (!intel_guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_GLOBAL, 0, &tmp))
+		if (!guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_GLOBAL, 0, &tmp, true))
 			num_regs += tmp;
 
-		if (!intel_guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_ENGINE_CLASS,
-						   engine->class, &tmp)) {
+		if (!guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_ENGINE_CLASS,
+					     engine->class, &tmp, true)) {
 			num_regs += tmp;
 		}
-		if (!intel_guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_ENGINE_INSTANCE,
-						   engine->class, &tmp)) {
+		if (!guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_ENGINE_INSTANCE,
+					     engine->class, &tmp, true)) {
 			num_regs += tmp;
 		}
 	}
Signature · 1 line
2.35.1
author maintainer
#255 lore raw

PATCH 256/1073 drm/i915/guc: Fix GuC error capture sizing estimation and reporting

In reply to Greg Kroah-Hartman

From: Alan Previn <[email protected]>

[ Upstream commit befb231d5de2773f6c6f6cf918234e2e709110a5 ]

During GuC error capture initialization, we estimate the amount of size we need for the error-capture-region of the shared GuC-log-buffer. This calculation was incorrect so fix that. With the fixed calculation we can reduce the allocation of error-capture region from 4MB to 1MB (see note2 below for reasoning). Additionally, switch from drm_notice to drm_debug for the 3X spare size check since that would be impossible to hit without redesigning gpu_coredump framework to hold multiple captures.

NOTE1: Even for 1x the min size estimation case, actually running out of space is a corner case because it can only occur if all engine instances get reset all at once and i915 isn't able extract the capture data fast enough within G2H handler worker.

NOTE2: With the corrected calculation, a DG2 part required ~77K and a PVC required ~115K (1X min-est-size that is calculated as one-shot all-engine- reset scenario).

Fixes d7c15d76a554 ("drm/i915/guc: Check sizing of guc_capture output")
Cc Alan Previn <[email protected]>
Cc Matthew Brost <[email protected]>
Cc Lucas De Marchi <[email protected]>
Cc John Harrison <[email protected]>
Cc Umesh Nerlige Ramappa <[email protected]>
Cc Balasubramani Vivekanandan <[email protected]>
Cc Matt Roper <[email protected]>
Cc Jani Nikula <[email protected]>
Cc Joonas Lahtinen <[email protected]>
Cc Chris Wilson <[email protected]>
---
 .../gpu/drm/i915/gt/uc/intel_guc_capture.c    | 29 ++++++++++++-------
 drivers/gpu/drm/i915/gt/uc/intel_guc_log.c    |  6 ++--
 2 files changed, 21 insertions(+), 14 deletions(-)
drivers/gpu/drm/i915/gt/uc/intel_guc_capture.c +18 -11
index c398bdd5403a..34e72675b7e4 100644
@@ -555,8 +555,9 @@ guc_capture_getlistsize(struct intel_guc *guc, u32 owner, u32 type, u32 classid,
 	if (!num_regs)
 		return -ENODATA;
 
-	*size = PAGE_ALIGN((sizeof(struct guc_debug_capture_list)) +
-			   (num_regs * sizeof(struct guc_mmio_reg)));
+	if (size)
+		*size = PAGE_ALIGN((sizeof(struct guc_debug_capture_list)) +
+				   (num_regs * sizeof(struct guc_mmio_reg)));
 
 	return 0;
 }
@@ -666,7 +667,7 @@ guc_capture_output_min_size_est(struct intel_guc *guc)
 	struct intel_gt *gt = guc_to_gt(guc);
 	struct intel_engine_cs *engine;
 	enum intel_engine_id id;
-	int worst_min_size = 0, num_regs = 0;
+	int worst_min_size = 0;
 	size_t tmp = 0;
 
 	if (!guc->capture)
@@ -688,20 +689,18 @@ guc_capture_output_min_size_est(struct intel_guc *guc)
 					 (3 * sizeof(struct guc_state_capture_header_t));
 
 		if (!guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_GLOBAL, 0, &tmp, true))
-			num_regs += tmp;
+			worst_min_size += tmp;
 
 		if (!guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_ENGINE_CLASS,
 					     engine->class, &tmp, true)) {
-			num_regs += tmp;
+			worst_min_size += tmp;
 		}
 		if (!guc_capture_getlistsize(guc, 0, GUC_CAPTURE_LIST_TYPE_ENGINE_INSTANCE,
 					     engine->class, &tmp, true)) {
-			num_regs += tmp;
+			worst_min_size += tmp;
 		}
 	}
 
-	worst_min_size += (num_regs * sizeof(struct guc_mmio_reg));
-
 	return worst_min_size;
 }
 
@@ -718,15 +717,23 @@ static void check_guc_capture_size(struct intel_guc *guc)
 	int spare_size = min_size * GUC_CAPTURE_OVERBUFFER_MULTIPLIER;
 	u32 buffer_size = intel_guc_log_section_size_capture(&guc->log);
 
+	/*
+	 * NOTE: min_size is much smaller than the capture region allocation (DG2: <80K vs 1MB)
+	 * Additionally, its based on space needed to fit all engines getting reset at once
+	 * within the same G2H handler task slot. This is very unlikely. However, if GuC really
+	 * does run out of space for whatever reason, we will see an separate warning message
+	 * when processing the G2H event capture-notification, search for:
+	 * INTEL_GUC_STATE_CAPTURE_EVENT_STATUS_NOSPACE.
+	 */
 	if (min_size < 0)
 		drm_warn(&i915->drm, "Failed to calculate GuC error state capture buffer minimum size: %d!\n",
 			 min_size);
 	else if (min_size > buffer_size)
-		drm_warn(&i915->drm, "GuC error state capture buffer is too small: %d < %d\n",
+		drm_warn(&i915->drm, "GuC error state capture buffer maybe small: %d < %d\n",
 			 buffer_size, min_size);
 	else if (spare_size > buffer_size)
-		drm_notice(&i915->drm, "GuC error state capture buffer maybe too small: %d < %d (min = %d)\n",
-			   buffer_size, spare_size, min_size);
+		drm_dbg(&i915->drm, "GuC error state capture buffer lacks spare size: %d < %d (min = %d)\n",
+			buffer_size, spare_size, min_size);
 }
 
 /*
drivers/gpu/drm/i915/gt/uc/intel_guc_log.c +3 -3
index 2b878030d3e1..8d755d285247 100644
@@ -16,15 +16,15 @@
 #if defined(CONFIG_DRM_I915_DEBUG_GUC)
 #define GUC_LOG_DEFAULT_CRASH_BUFFER_SIZE	SZ_2M
 #define GUC_LOG_DEFAULT_DEBUG_BUFFER_SIZE	SZ_16M
-#define GUC_LOG_DEFAULT_CAPTURE_BUFFER_SIZE	SZ_4M
+#define GUC_LOG_DEFAULT_CAPTURE_BUFFER_SIZE	SZ_1M
 #elif defined(CONFIG_DRM_I915_DEBUG_GEM)
 #define GUC_LOG_DEFAULT_CRASH_BUFFER_SIZE	SZ_1M
 #define GUC_LOG_DEFAULT_DEBUG_BUFFER_SIZE	SZ_2M
-#define GUC_LOG_DEFAULT_CAPTURE_BUFFER_SIZE	SZ_4M
+#define GUC_LOG_DEFAULT_CAPTURE_BUFFER_SIZE	SZ_1M
 #else
 #define GUC_LOG_DEFAULT_CRASH_BUFFER_SIZE	SZ_8K
 #define GUC_LOG_DEFAULT_DEBUG_BUFFER_SIZE	SZ_64K
-#define GUC_LOG_DEFAULT_CAPTURE_BUFFER_SIZE	SZ_2M
+#define GUC_LOG_DEFAULT_CAPTURE_BUFFER_SIZE	SZ_1M
 #endif
 
 static void guc_log_copy_debuglogs_for_relay(struct intel_guc_log *log);
Signature · 1 line
2.35.1
author maintainer
#256 lore raw

PATCH 257/1073 dw9768: Enable low-power probe on ACPI

In reply to Greg Kroah-Hartman

From: Sakari Ailus <[email protected]>

[ Upstream commit 5f9a089b6de34655318afe8e544d9a9cc0fc1d29 ]

Add support for low-power probe to the driver. Also fix runtime PM API usage in the driver.

Much of the hassle comes from different factors affecting device power states during probe for ACPI and DT.

Fixes 859891228e56 ("media: i2c: dw9768: Add DW9768 VCM driver")
---
 drivers/media/i2c/dw9768.c | 33 +++++++++++++++++++++++++--------
 1 file changed, 25 insertions(+), 8 deletions(-)
drivers/media/i2c/dw9768.c +25 -8
index c086580efac7..60ae0adf5174 100644
@@ -414,6 +414,7 @@ static int dw9768_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
 	struct dw9768 *dw9768;
+	bool full_power;
 	unsigned int i;
 	int ret;
 
@@ -469,13 +470,23 @@ static int dw9768_probe(struct i2c_client *client)
 
 	dw9768->sd.entity.function = MEDIA_ENT_F_LENS;
 
+	/*
+	 * Figure out whether we're going to power up the device here. Generally
+	 * this is done if CONFIG_PM is disabled in a DT system or the device is
+	 * to be powered on in an ACPI system. Similarly for power off in
+	 * remove.
+	 */
 	pm_runtime_enable(dev);
-	if (!pm_runtime_enabled(dev)) {
+	full_power = (is_acpi_node(dev_fwnode(dev)) &&
+		      acpi_dev_state_d0(dev)) ||
+		     (is_of_node(dev_fwnode(dev)) && !pm_runtime_enabled(dev));
+	if (full_power) {
 		ret = dw9768_runtime_resume(dev);
 		if (ret < 0) {
 			dev_err(dev, "failed to power on: %d\n", ret);
 			goto err_clean_entity;
 		}
+		pm_runtime_set_active(dev);
 	}
 
 	ret = v4l2_async_register_subdev(&dw9768->sd);
@@ -484,14 +495,17 @@ static int dw9768_probe(struct i2c_client *client)
 		goto err_power_off;
 	}
 
+	pm_runtime_idle(dev);
+
 	return 0;
 
 err_power_off:
-	if (pm_runtime_enabled(dev))
-		pm_runtime_disable(dev);
-	else
+	if (full_power) {
 		dw9768_runtime_suspend(dev);
+		pm_runtime_set_suspended(dev);
+	}
 err_clean_entity:
+	pm_runtime_disable(dev);
 	media_entity_cleanup(&dw9768->sd.entity);
 err_free_handler:
 	v4l2_ctrl_handler_free(&dw9768->ctrls);
@@ -503,14 +517,17 @@ static int dw9768_remove(struct i2c_client *client)
 {
 	struct v4l2_subdev *sd = i2c_get_clientdata(client);
 	struct dw9768 *dw9768 = sd_to_dw9768(sd);
+	struct device *dev = &client->dev;
 
 	v4l2_async_unregister_subdev(&dw9768->sd);
 	v4l2_ctrl_handler_free(&dw9768->ctrls);
 	media_entity_cleanup(&dw9768->sd.entity);
-	pm_runtime_disable(&client->dev);
-	if (!pm_runtime_status_suspended(&client->dev))
-		dw9768_runtime_suspend(&client->dev);
-	pm_runtime_set_suspended(&client->dev);
+	if ((is_acpi_node(dev_fwnode(dev)) && acpi_dev_state_d0(dev)) ||
+	    (is_of_node(dev_fwnode(dev)) && !pm_runtime_enabled(dev))) {
+		dw9768_runtime_suspend(dev);
+		pm_runtime_set_suspended(dev);
+	}
+	pm_runtime_disable(dev);
 
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#257 lore raw

PATCH 258/1073 drm/amd/display: wait for vblank during pipe programming

In reply to Greg Kroah-Hartman

From: Haiyi Zhou <[email protected]>

[ Upstream commit 203ccaf586446b578909de1b763278033fb74b51 ]

[WHY]
Skipping vblank during global sync update request can result in underflow on certain displays.

[HOW]
Roll back to the previous behavior where DC waits for vblank during pipe programming.

Fixes 5d3e14421410 ("drm/amd/display: do not wait for vblank during pipe programming")
---
 drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c +2 -4
index 0f30df523fdf..146189323dbe 100644
@@ -1632,10 +1632,8 @@ static void dcn20_program_pipe(
 				pipe_ctx->pipe_dlg_param.vupdate_width);
 
 		if (pipe_ctx->stream->mall_stream_config.type != SUBVP_PHANTOM) {
-			pipe_ctx->stream_res.tg->funcs->wait_for_state(
-				pipe_ctx->stream_res.tg, CRTC_STATE_VBLANK);
-			pipe_ctx->stream_res.tg->funcs->wait_for_state(
-				pipe_ctx->stream_res.tg, CRTC_STATE_VACTIVE);
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VBLANK);
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VACTIVE);
 		}
 
 		pipe_ctx->stream_res.tg->funcs->set_vtg_params(
Signature · 1 line
2.35.1
author maintainer
#258 lore raw

PATCH 259/1073 drm/rockchip: lvds: fix PM usage counter unbalance in poweron

In reply to Greg Kroah-Hartman

From: Zhang Qilong <[email protected]>

[ Upstream commit 4dba27f1a14592ac4cf71c3bc1cc1fd05dea8015 ]

pm_runtime_get_sync will increment pm usage counter even it failed. Forgetting to putting operation will result in reference leak here. We fix it by replacing it with the newest pm_runtime_resume_and_get to keep usage counter balanced.

Fixes 34cc0aa25456 ("drm/rockchip: Add support for Rockchip Soc LVDS")
Fixes cca1705c3d89 ("drm/rockchip: lvds: Add PX30 support")
---
 drivers/gpu/drm/rockchip/rockchip_lvds.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/gpu/drm/rockchip/rockchip_lvds.c +7 -3
index 5a284332ec49..68f6ebb33460 100644
@@ -152,7 +152,7 @@ static int rk3288_lvds_poweron(struct rockchip_lvds *lvds)
 		DRM_DEV_ERROR(lvds->dev, "failed to enable lvds pclk %d\n", ret);
 		return ret;
 	}
-	ret = pm_runtime_get_sync(lvds->dev);
+	ret = pm_runtime_resume_and_get(lvds->dev);
 	if (ret < 0) {
 		DRM_DEV_ERROR(lvds->dev, "failed to get pm runtime: %d\n", ret);
 		clk_disable(lvds->pclk);
@@ -336,16 +336,20 @@ static int px30_lvds_poweron(struct rockchip_lvds *lvds)
 {
 	int ret;
 
-	ret = pm_runtime_get_sync(lvds->dev);
+	ret = pm_runtime_resume_and_get(lvds->dev);
 	if (ret < 0) {
 		DRM_DEV_ERROR(lvds->dev, "failed to get pm runtime: %d\n", ret);
 		return ret;
 	}
 
 	/* Enable LVDS mode */
-	return regmap_update_bits(lvds->grf, PX30_LVDS_GRF_PD_VO_CON1,
+	ret = regmap_update_bits(lvds->grf, PX30_LVDS_GRF_PD_VO_CON1,
 				  PX30_LVDS_MODE_EN(1) | PX30_LVDS_P2S_EN(1),
 				  PX30_LVDS_MODE_EN(1) | PX30_LVDS_P2S_EN(1));
+	if (ret)
+		pm_runtime_put(lvds->dev);
+
+	return ret;
 }
 
 static void px30_lvds_poweroff(struct rockchip_lvds *lvds)
Signature · 1 line
2.35.1
author maintainer
#259 lore raw

PATCH 260/1073 clk: renesas: r9a06g032: Repair grave increment error

In reply to Greg Kroah-Hartman

From: Marek Vasut <[email protected]>

[ Upstream commit 02693e11611e082e3c4d8653e8af028e43d31164 ]

If condition (clkspec.np != pd->dev.of_node) is true, then the driver ends up in an endless loop, forever, locking up the machine.

---
 drivers/clk/renesas/r9a06g032-clocks.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/clk/renesas/r9a06g032-clocks.c +1 -2
index 1488c9d6e639..983faa5707b9 100644
@@ -412,7 +412,7 @@ static int r9a06g032_attach_dev(struct generic_pm_domain *pd,
 	int error;
 	int index;
 
-	while (!of_parse_phandle_with_args(np, "clocks", "#clock-cells", i,
+	while (!of_parse_phandle_with_args(np, "clocks", "#clock-cells", i++,
 					   &clkspec)) {
 		if (clkspec.np != pd->dev.of_node)
 			continue;
@@ -425,7 +425,6 @@ static int r9a06g032_attach_dev(struct generic_pm_domain *pd,
 			if (error)
 				return error;
 		}
-		i++;
 	}
 
 	return 0;
Signature · 1 line
2.35.1
author maintainer
#260 lore raw

PATCH 261/1073 drm: lcdif: change burst size to 256B

In reply to Greg Kroah-Hartman

From: Marco Felsch <[email protected]>

[ Upstream commit 2215cb3be5c28a1fd43036550c00c2371aeeba95 ]

If a axi bus master with a higher priority do a lot of memory access FIFO underruns can be inspected. Increase the burst size to 256B to avoid such underruns and to improve the memory access efficiency.

Fixes 9db35bb349a0 ("drm: lcdif: Add support for i.MX8MP LCDIF variant")
---
 drivers/gpu/drm/mxsfb/lcdif_kms.c  | 14 ++++++++++++--
 drivers/gpu/drm/mxsfb/lcdif_regs.h |  4 ++++
 2 files changed, 16 insertions(+), 2 deletions(-)
drivers/gpu/drm/mxsfb/lcdif_kms.c +12 -2
index 11f881554f74..713b0d756f2a 100644
@@ -149,8 +149,18 @@ static void lcdif_set_mode(struct lcdif_drm_private *lcdif, u32 bus_flags)
 	       CTRLDESCL0_1_WIDTH(m->crtc_hdisplay),
 	       lcdif->base + LCDC_V8_CTRLDESCL0_1);
 
-	writel(CTRLDESCL0_3_PITCH(lcdif->crtc.primary->state->fb->pitches[0]),
-	       lcdif->base + LCDC_V8_CTRLDESCL0_3);
+	/*
+	 * Undocumented P_SIZE and T_SIZE register but those written in the
+	 * downstream kernel those registers control the AXI burst size. As of
+	 * now there are two known values:
+	 *  1 - 128Byte
+	 *  2 - 256Byte
+	 * Downstream set it to 256B burst size to improve the memory
+	 * efficiency so set it here too.
+	 */
+	ctrl = CTRLDESCL0_3_P_SIZE(2) | CTRLDESCL0_3_T_SIZE(2) |
+	       CTRLDESCL0_3_PITCH(lcdif->crtc.primary->state->fb->pitches[0]);
+	writel(ctrl, lcdif->base + LCDC_V8_CTRLDESCL0_3);
 }
 
 static void lcdif_enable_controller(struct lcdif_drm_private *lcdif)
drivers/gpu/drm/mxsfb/lcdif_regs.h +4 -0
index c70220651e3a..8e8bef175bf2 100644
@@ -190,6 +190,10 @@
 #define CTRLDESCL0_1_WIDTH(n)		((n) & 0xffff)
 #define CTRLDESCL0_1_WIDTH_MASK		GENMASK(15, 0)
 
+#define CTRLDESCL0_3_P_SIZE(n)		(((n) << 20) & CTRLDESCL0_3_P_SIZE_MASK)
+#define CTRLDESCL0_3_P_SIZE_MASK	GENMASK(22, 20)
+#define CTRLDESCL0_3_T_SIZE(n)		(((n) << 16) & CTRLDESCL0_3_T_SIZE_MASK)
+#define CTRLDESCL0_3_T_SIZE_MASK	GENMASK(17, 16)
 #define CTRLDESCL0_3_PITCH(n)		((n) & 0xffff)
 #define CTRLDESCL0_3_PITCH_MASK		GENMASK(15, 0)
 
Signature · 1 line
2.35.1
author maintainer
#261 lore raw

PATCH 262/1073 spi: Update reference to struct spi_controller

In reply to Greg Kroah-Hartman

From: Jonathan Neuschäfer <[email protected]>

[ Upstream commit bf585ccee22faf469d82727cf375868105b362f7 ]

struct spi_master has been renamed to struct spi_controller. Update the reference in spi.rst to make it clickable again.

Fixes 8caab75fd2c2 ("spi: Generalize SPI "master" to "controller"")
---
 Documentation/driver-api/spi.rst | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
Documentation/driver-api/spi.rst +2 -2
index f64cb666498a..f28887045049 100644
@@ -25,8 +25,8 @@ hardware, which may be as simple as a set of GPIO pins or as complex as
 a pair of FIFOs connected to dual DMA engines on the other side of the
 SPI shift register (maximizing throughput). Such drivers bridge between
 whatever bus they sit on (often the platform bus) and SPI, and expose
-the SPI side of their device as a :c:type:`struct spi_master
-<spi_master>`. SPI devices are children of that master,
+the SPI side of their device as a :c:type:`struct spi_controller
+<spi_controller>`. SPI devices are children of that master,
 represented as a :c:type:`struct spi_device <spi_device>` and
 manufactured from :c:type:`struct spi_board_info
 <spi_board_info>` descriptors which are usually provided by
Signature · 1 line
2.35.1
author maintainer
#262 lore raw

PATCH 263/1073 drm/panel/panel-sitronix-st7701: Remove panel on DSI attach failure

In reply to Greg Kroah-Hartman

From: Marek Vasut <[email protected]>

[ Upstream commit c62102165dd79284d42383d2f7ed17301bd8e629 ]

In case mipi_dsi_attach() fails, call drm_panel_remove() to avoid memory leak.

Fixes 849b2e3ff969 ("drm/panel: Add Sitronix ST7701 panel driver")
---
 drivers/gpu/drm/panel/panel-sitronix-st7701.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
drivers/gpu/drm/panel/panel-sitronix-st7701.c +9 -1
index 320a2a8fd459..098955526b68 100644
@@ -384,7 +384,15 @@ static int st7701_dsi_probe(struct mipi_dsi_device *dsi)
 	st7701->dsi = dsi;
 	st7701->desc = desc;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret)
+		goto err_attach;
+
+	return 0;
+
+err_attach:
+	drm_panel_remove(&st7701->panel);
+	return ret;
 }
 
 static int st7701_dsi_remove(struct mipi_dsi_device *dsi)
Signature · 1 line
2.35.1
author maintainer
#263 lore raw

PATCH 264/1073 drm/ttm: fix undefined behavior in bit shift for TTM_TT_FLAG_PRIV_POPULATED

In reply to Greg Kroah-Hartman

From: Gaosheng Cui <[email protected]>

[ Upstream commit 387659939c00156f8d6bab0fbc55b4eaf2b6bc5b ]

Shifting signed 32-bit value by 31 bits is undefined, so changing significant bit to unsigned. The UBSAN warning calltrace like below:

UBSAN: shift-out-of-bounds in ./include/drm/ttm/ttm_tt.h:122:26
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
 <TASK>
 dump_stack_lvl+0x7d/0xa5
 dump_stack+0x15/0x1b
 ubsan_epilogue+0xe/0x4e
 __ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
 ttm_bo_move_memcpy+0x3b4/0x460 [ttm]
 bo_driver_move+0x32/0x40 [drm_vram_helper]
 ttm_bo_handle_move_mem+0x118/0x200 [ttm]
 ttm_bo_validate+0xfa/0x220 [ttm]
 drm_gem_vram_pin_locked+0x70/0x1b0 [drm_vram_helper]
 drm_gem_vram_pin+0x48/0xb0 [drm_vram_helper]
 drm_gem_vram_plane_helper_prepare_fb+0x53/0xe0 [drm_vram_helper]
 drm_gem_vram_simple_display_pipe_prepare_fb+0x26/0x30 [drm_vram_helper]
 drm_simple_kms_plane_prepare_fb+0x4d/0xe0 [drm_kms_helper]
 drm_atomic_helper_prepare_planes+0xda/0x210 [drm_kms_helper]
 drm_atomic_helper_commit+0xc3/0x1e0 [drm_kms_helper]
 drm_atomic_commit+0x9c/0x160 [drm]
 drm_client_modeset_commit_atomic+0x33a/0x380 [drm]
 drm_client_modeset_commit_locked+0x77/0x220 [drm]
 drm_client_modeset_commit+0x31/0x60 [drm]
 __drm_fb_helper_restore_fbdev_mode_unlocked+0xa7/0x170 [drm_kms_helper]
 drm_fb_helper_set_par+0x51/0x90 [drm_kms_helper]
 fbcon_init+0x316/0x790
 visual_init+0x113/0x1d0
 do_bind_con_driver+0x2a3/0x5c0
 do_take_over_console+0xa9/0x270
 do_fbcon_takeover+0xa1/0x170
 do_fb_registered+0x2a8/0x340
 fbcon_fb_registered+0x47/0xe0
 register_framebuffer+0x294/0x4a0
 __drm_fb_helper_initial_config_and_unlock+0x43c/0x880 [drm_kms_helper]
 drm_fb_helper_initial_config+0x52/0x80 [drm_kms_helper]
 drm_fbdev_client_hotplug+0x156/0x1b0 [drm_kms_helper]
 drm_fbdev_generic_setup+0xfc/0x290 [drm_kms_helper]
 bochs_pci_probe+0x6ca/0x772 [bochs]
 local_pci_probe+0x4d/0xb0
 pci_device_probe+0x119/0x320
 really_probe+0x181/0x550
 __driver_probe_device+0xc6/0x220
 driver_probe_device+0x32/0x100
 __driver_attach+0x195/0x200
 bus_for_each_dev+0xbb/0x120
 driver_attach+0x27/0x30
 bus_add_driver+0x22e/0x2f0
 driver_register+0xa9/0x190
 __pci_register_driver+0x90/0xa0
 bochs_pci_driver_init+0x52/0x1000 [bochs]
 do_one_initcall+0x76/0x430
 do_init_module+0x61/0x28a
 load_module+0x1f82/0x2e50
 __do_sys_finit_module+0xf8/0x190
 __x64_sys_finit_module+0x23/0x30
 do_syscall_64+0x58/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd
 </TASK>
---
 include/drm/ttm/ttm_tt.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/drm/ttm/ttm_tt.h +1 -1
index 17a0310e8aaa..b7d3f3843f1e 100644
@@ -88,7 +88,7 @@ struct ttm_tt {
 #define TTM_TT_FLAG_EXTERNAL		(1 << 2)
 #define TTM_TT_FLAG_EXTERNAL_MAPPABLE	(1 << 3)
 
-#define TTM_TT_FLAG_PRIV_POPULATED  (1 << 31)
+#define TTM_TT_FLAG_PRIV_POPULATED  (1U << 31)
 	uint32_t page_flags;
 	/** @num_pages: Number of pages in the page array. */
 	uint32_t num_pages;
Signature · 1 line
2.35.1
author maintainer
#264 lore raw

PATCH 265/1073 drm/msm/mdp5: stop overriding drvdata

In reply to Greg Kroah-Hartman

From: Dmitry Baryshkov <[email protected]>

[ Upstream commit c6122688f2652d7f8a44000ce21e84e82bae2b5e ]

The rest of the code expects that master's device drvdata is the struct msm_drm_private instance. Do not override the mdp5's drvdata.

Fixes 6874f48bb8b0 ("drm/msm: make mdp5/dpu devices master components")

Patchwork: https://patchwork.freedesktop.org/patch/508334/

---
 drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c | 32 +++++++++++++-----------
 1 file changed, 17 insertions(+), 15 deletions(-)
drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c +17 -15
index b0d21838a134..b46f983f2b46 100644
@@ -203,7 +203,7 @@ static int mdp5_set_split_display(struct msm_kms *kms,
 							  slave_encoder);
 }
 
-static void mdp5_destroy(struct platform_device *pdev);
+static void mdp5_destroy(struct mdp5_kms *mdp5_kms);
 
 static void mdp5_kms_destroy(struct msm_kms *kms)
 {
@@ -223,7 +223,7 @@ static void mdp5_kms_destroy(struct msm_kms *kms)
 	}
 
 	mdp_kms_destroy(&mdp5_kms->base);
-	mdp5_destroy(mdp5_kms->pdev);
+	mdp5_destroy(mdp5_kms);
 }
 
 #ifdef CONFIG_DEBUG_FS
@@ -519,9 +519,10 @@ static void read_mdp_hw_revision(struct mdp5_kms *mdp5_kms,
 	struct device *dev = &mdp5_kms->pdev->dev;
 	u32 version;
 
-	pm_runtime_get_sync(dev);
+	/* Manually enable the MDP5, as pm runtime isn't usable yet. */
+	mdp5_enable(mdp5_kms);
 	version = mdp5_read(mdp5_kms, REG_MDP5_HW_VERSION);
-	pm_runtime_put_sync(dev);
+	mdp5_disable(mdp5_kms);
 
 	*major = FIELD(version, MDP5_HW_VERSION_MAJOR);
 	*minor = FIELD(version, MDP5_HW_VERSION_MINOR);
@@ -559,6 +560,8 @@ static int mdp5_kms_init(struct drm_device *dev)
 	int irq, i, ret;
 
 	ret = mdp5_init(to_platform_device(dev->dev), dev);
+	if (ret)
+		return ret;
 
 	/* priv->kms would have been populated by the MDP5 driver */
 	kms = priv->kms;
@@ -632,9 +635,8 @@ static int mdp5_kms_init(struct drm_device *dev)
 	return ret;
 }
 
-static void mdp5_destroy(struct platform_device *pdev)
+static void mdp5_destroy(struct mdp5_kms *mdp5_kms)
 {
-	struct mdp5_kms *mdp5_kms = platform_get_drvdata(pdev);
 	int i;
 
 	if (mdp5_kms->ctlm)
@@ -648,7 +650,7 @@ static void mdp5_destroy(struct platform_device *pdev)
 		kfree(mdp5_kms->intfs[i]);
 
 	if (mdp5_kms->rpm_enabled)
-		pm_runtime_disable(&pdev->dev);
+		pm_runtime_disable(&mdp5_kms->pdev->dev);
 
 	drm_atomic_private_obj_fini(&mdp5_kms->glob_state);
 	drm_modeset_lock_fini(&mdp5_kms->glob_state_lock);
@@ -797,8 +799,6 @@ static int mdp5_init(struct platform_device *pdev, struct drm_device *dev)
 		goto fail;
 	}
 
-	platform_set_drvdata(pdev, mdp5_kms);
-
 	spin_lock_init(&mdp5_kms->resource_lock);
 
 	mdp5_kms->dev = dev;
@@ -839,9 +839,6 @@ static int mdp5_init(struct platform_device *pdev, struct drm_device *dev)
 	 */
 	clk_set_rate(mdp5_kms->core_clk, 200000000);
 
-	pm_runtime_enable(&pdev->dev);
-	mdp5_kms->rpm_enabled = true;
-
 	read_mdp_hw_revision(mdp5_kms, &major, &minor);
 
 	mdp5_kms->cfg = mdp5_cfg_init(mdp5_kms, major, minor);
@@ -893,10 +890,13 @@ static int mdp5_init(struct platform_device *pdev, struct drm_device *dev)
 	/* set uninit-ed kms */
 	priv->kms = &mdp5_kms->base.base;
 
+	pm_runtime_enable(&pdev->dev);
+	mdp5_kms->rpm_enabled = true;
+
 	return 0;
 fail:
 	if (mdp5_kms)
-		mdp5_destroy(pdev);
+		mdp5_destroy(mdp5_kms);
 	return ret;
 }
 
@@ -953,7 +953,8 @@ static int mdp5_dev_remove(struct platform_device *pdev)
 static __maybe_unused int mdp5_runtime_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
-	struct mdp5_kms *mdp5_kms = platform_get_drvdata(pdev);
+	struct msm_drm_private *priv = platform_get_drvdata(pdev);
+	struct mdp5_kms *mdp5_kms = to_mdp5_kms(to_mdp_kms(priv->kms));
 
 	DBG("");
 
@@ -963,7 +964,8 @@ static __maybe_unused int mdp5_runtime_suspend(struct device *dev)
 static __maybe_unused int mdp5_runtime_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
-	struct mdp5_kms *mdp5_kms = platform_get_drvdata(pdev);
+	struct msm_drm_private *priv = platform_get_drvdata(pdev);
+	struct mdp5_kms *mdp5_kms = to_mdp5_kms(to_mdp_kms(priv->kms));
 
 	DBG("");
 
Signature · 1 line
2.35.1
author maintainer
#265 lore raw

PATCH 266/1073 ima: Handle -ESTALE returned by ima_filter_rule_match()

In reply to Greg Kroah-Hartman

From: GUO Zihua <[email protected]>

[ Upstream commit c7423dbdbc9ecef7fff5239d144cad4b9887f4de ]

IMA relies on the blocking LSM policy notifier callback to update the LSM based IMA policy rules.

When SELinux update its policies, IMA would be notified and starts updating all its lsm rules one-by-one. During this time, -ESTALE would be returned by ima_filter_rule_match() if it is called with a LSM rule that has not yet been updated. In ima_match_rules(), -ESTALE is not handled, and the LSM rule is considered a match, causing extra files to be measured by IMA.

Fix it by re-initializing a temporary rule if -ESTALE is returned by ima_filter_rule_match(). The origin rule in the rule list would be updated by the LSM policy notifier callback.

Fixes b16942455193 ("ima: use the lsm policy update notifier")
---
 security/integrity/ima/ima_policy.c | 41 ++++++++++++++++++++++-------
 1 file changed, 32 insertions(+), 9 deletions(-)
security/integrity/ima/ima_policy.c +32 -9
index a8802b8da946..bb3707160b01 100644
@@ -549,6 +549,9 @@ static bool ima_match_rules(struct ima_rule_entry *rule,
 			    const char *func_data)
 {
 	int i;
+	bool result = false;
+	struct ima_rule_entry *lsm_rule = rule;
+	bool rule_reinitialized = false;
 
 	if ((rule->flags & IMA_FUNC) &&
 	    (rule->func != func && func != POST_SETATTR))
@@ -610,35 +613,55 @@ static bool ima_match_rules(struct ima_rule_entry *rule,
 		int rc = 0;
 		u32 osid;
 
-		if (!rule->lsm[i].rule) {
-			if (!rule->lsm[i].args_p)
+		if (!lsm_rule->lsm[i].rule) {
+			if (!lsm_rule->lsm[i].args_p)
 				continue;
 			else
 				return false;
 		}
+
+retry:
 		switch (i) {
 		case LSM_OBJ_USER:
 		case LSM_OBJ_ROLE:
 		case LSM_OBJ_TYPE:
 			security_inode_getsecid(inode, &osid);
-			rc = ima_filter_rule_match(osid, rule->lsm[i].type,
+			rc = ima_filter_rule_match(osid, lsm_rule->lsm[i].type,
 						   Audit_equal,
-						   rule->lsm[i].rule);
+						   lsm_rule->lsm[i].rule);
 			break;
 		case LSM_SUBJ_USER:
 		case LSM_SUBJ_ROLE:
 		case LSM_SUBJ_TYPE:
-			rc = ima_filter_rule_match(secid, rule->lsm[i].type,
+			rc = ima_filter_rule_match(secid, lsm_rule->lsm[i].type,
 						   Audit_equal,
-						   rule->lsm[i].rule);
+						   lsm_rule->lsm[i].rule);
 			break;
 		default:
 			break;
 		}
-		if (!rc)
-			return false;
+
+		if (rc == -ESTALE && !rule_reinitialized) {
+			lsm_rule = ima_lsm_copy_rule(rule);
+			if (lsm_rule) {
+				rule_reinitialized = true;
+				goto retry;
+			}
+		}
+		if (!rc) {
+			result = false;
+			goto out;
+		}
 	}
-	return true;
+	result = true;
+
+out:
+	if (rule_reinitialized) {
+		for (i = 0; i < MAX_LSM_RULES; i++)
+			ima_filter_rule_free(lsm_rule->lsm[i].rule);
+		kfree(lsm_rule);
+	}
+	return result;
 }
 
 /*
Signature · 1 line
2.35.1
author maintainer
#266 lore raw

PATCH 267/1073 drm/msm/hdmi: use devres helper for runtime PM management

In reply to Greg Kroah-Hartman

From: Dmitry Baryshkov <[email protected]>

[ Upstream commit b964444b2b64ce182495731d830499d1c588ccf6 ]

Use devm_pm_runtime_enable() to enable runtime PM. This way its effect will be reverted on device unbind/destruction.

Fixes 6ed9ed484d04 ("drm/msm/hdmi: Set up runtime PM for HDMI")

Patchwork: https://patchwork.freedesktop.org/patch/499647/

---
 drivers/gpu/drm/msm/hdmi/hdmi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/msm/hdmi/hdmi.c +1 -1
index f28fb21e3891..8cd5d50639a5 100644
@@ -252,7 +252,7 @@ static struct hdmi *msm_hdmi_init(struct platform_device *pdev)
 	if (hdmi->hpd_gpiod)
 		gpiod_set_consumer_name(hdmi->hpd_gpiod, "HDMI_HPD");
 
-	pm_runtime_enable(&pdev->dev);
+	devm_pm_runtime_enable(&pdev->dev);
 
 	hdmi->workq = alloc_ordered_workqueue("msm_hdmi", 0);
 
Signature · 1 line
2.35.1
author maintainer
#267 lore raw

PATCH 268/1073 bpf: Clobber stack slot when writing over spilled PTR_TO_BTF_ID

In reply to Greg Kroah-Hartman

From: Kumar Kartikeya Dwivedi <[email protected]>

[ Upstream commit 261f4664caffdeb9dff4e83ee3c0334b1c3a552f ]

When support was added for spilled PTR_TO_BTF_ID to be accessed by helper memory access, the stack slot was not overwritten to STACK_MISC (and that too is only safe when env->allow_ptr_leaks is true).

This means that helpers who take ARG_PTR_TO_MEM and write to it may essentially overwrite the value while the verifier continues to track the slot for spilled register.

This can cause issues when PTR_TO_BTF_ID is spilled to stack, and then overwritten by helper write access, which can then be passed to BPF helpers or kfuncs.

Handle this by falling back to the case introduced in a later commit, which will also handle PTR_TO_BTF_ID along with other pointer types, i.e. cd17d38f8b28 ("bpf: Permits pointers on stack for helper calls").

Finally, include a comment on why REG_LIVE_WRITTEN is not being set when clobber is set to true. In short, the reason is that while when clobber is unset, we know that we won't be writing, when it is true, we *may* write to any of the stack slots in that range. It may be a partial or complete write, to just one or many stack slots.

We cannot be sure, hence to be conservative, we leave things as is and never set REG_LIVE_WRITTEN for any stack slot. However, clobber still needs to reset them to STACK_MISC assuming writes happened. However read marks still need to be propagated upwards from liveness point of view, as parent stack slot's contents may still continue to matter to child states.

Cc Yonghong Song <[email protected]>
Fixes 1d68f22b3d53 ("bpf: Handle spilled PTR_TO_BTF_ID properly when checking stack_boundary")
---
 kernel/bpf/verifier.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
kernel/bpf/verifier.c +5 -4
index b781075dd510..65c627571e33 100644
@@ -5142,10 +5142,6 @@ static int check_stack_range_initialized(
 			goto mark;
 		}
 
-		if (is_spilled_reg(&state->stack[spi]) &&
-		    base_type(state->stack[spi].spilled_ptr.type) == PTR_TO_BTF_ID)
-			goto mark;
-
 		if (is_spilled_reg(&state->stack[spi]) &&
 		    (state->stack[spi].spilled_ptr.type == SCALAR_VALUE ||
 		     env->allow_ptr_leaks)) {
@@ -5176,6 +5172,11 @@ static int check_stack_range_initialized(
 		mark_reg_read(env, &state->stack[spi].spilled_ptr,
 			      state->stack[spi].spilled_ptr.parent,
 			      REG_LIVE_READ64);
+		/* We do not set REG_LIVE_WRITTEN for stack slot, as we can not
+		 * be sure that whether stack slot is written to or not. Hence,
+		 * we must still conservatively propagate reads upwards even if
+		 * helper may write to the entire memory range.
+		 */
 	}
 	return update_stack_depth(env, state, min_off);
 }
Signature · 1 line
2.35.1
author maintainer
#268 lore raw

PATCH 269/1073 bpf: Fix slot type check in check_stack_write_var_off

In reply to Greg Kroah-Hartman

From: Kumar Kartikeya Dwivedi <[email protected]>

[ Upstream commit f5e477a861e4a20d8a1c5f7a245f3a3c3c376b03 ]

For the case where allow_ptr_leaks is false, code is checking whether slot type is STACK_INVALID and STACK_SPILL and rejecting other cases. This is a consequence of incorrectly checking for register type instead of the slot type (NOT_INIT and SCALAR_VALUE respectively). Fix the check.

---
 kernel/bpf/verifier.c | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)
kernel/bpf/verifier.c +11 -8
index 65c627571e33..95479562a64a 100644
@@ -3169,14 +3169,17 @@ static int check_stack_write_var_off(struct bpf_verifier_env *env,
 		stype = &state->stack[spi].slot_type[slot % BPF_REG_SIZE];
 		mark_stack_slot_scratched(env, spi);
 
-		if (!env->allow_ptr_leaks
-				&& *stype != NOT_INIT
-				&& *stype != SCALAR_VALUE) {
-			/* Reject the write if there's are spilled pointers in
-			 * range. If we didn't reject here, the ptr status
-			 * would be erased below (even though not all slots are
-			 * actually overwritten), possibly opening the door to
-			 * leaks.
+		if (!env->allow_ptr_leaks && *stype != STACK_MISC && *stype != STACK_ZERO) {
+			/* Reject the write if range we may write to has not
+			 * been initialized beforehand. If we didn't reject
+			 * here, the ptr status would be erased below (even
+			 * though not all slots are actually overwritten),
+			 * possibly opening the door to leaks.
+			 *
+			 * We do however catch STACK_INVALID case below, and
+			 * only allow reading possibly uninitialized memory
+			 * later for CAP_PERFMON, as the write may not happen to
+			 * that slot.
 			 */
 			verbose(env, "spilled ptr in range of var-offset stack write; insn %d, ptr off: %d",
 				insn_idx, i);
Signature · 1 line
2.35.1
author maintainer
#269 lore raw

PATCH 270/1073 drm/msm/dpu: use drm_dsc_config instead of msm_display_dsc_config

In reply to Greg Kroah-Hartman

From: Dmitry Baryshkov <[email protected]>

[ Upstream commit 46dd0c0658ff5783acce37dcfe437e2a79a9934e ]

There is no need to use the struct msm_display_dsc_config wrapper inside the dpu driver, use the struct drm_dsc_config directly to pass pps data.

Patchwork: https://patchwork.freedesktop.org/patch/493340/

Stable-dep-of: d3c1a8663d0d ("drm/msm/dpu1: Account for DSC's bits_per_pixel having 4 fractional bits")

---
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 25 +++----
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h |  2 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c  | 74 ++++++++++-----------
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h  |  4 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c     |  2 +-
 5 files changed, 54 insertions(+), 53 deletions(-)
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c +13 -12
index 52a626117f70..7f5dba96b2ff 100644
@@ -162,7 +162,7 @@ enum dpu_enc_rc_states {
  * @vsync_event_work:		worker to handle vsync event for autorefresh
  * @topology:                   topology of the display
  * @idle_timeout:		idle timeout duration in milliseconds
- * @dsc:			msm_display_dsc_config pointer, for DSC-enabled encoders
+ * @dsc:			drm_dsc_config pointer, for DSC-enabled encoders
  */
 struct dpu_encoder_virt {
 	struct drm_encoder base;
@@ -208,7 +208,7 @@ struct dpu_encoder_virt {
 	bool wide_bus_en;
 
 	/* DSC configuration */
-	struct msm_display_dsc_config *dsc;
+	struct drm_dsc_config *dsc;
 };
 
 #define to_dpu_encoder_virt(x) container_of(x, struct dpu_encoder_virt, base)
@@ -1791,12 +1791,12 @@ static void dpu_encoder_vsync_event_work_handler(struct kthread_work *work)
 }
 
 static u32
-dpu_encoder_dsc_initial_line_calc(struct msm_display_dsc_config *dsc,
+dpu_encoder_dsc_initial_line_calc(struct drm_dsc_config *dsc,
 				  u32 enc_ip_width)
 {
 	int ssm_delay, total_pixels, soft_slice_per_enc;
 
-	soft_slice_per_enc = enc_ip_width / dsc->drm->slice_width;
+	soft_slice_per_enc = enc_ip_width / dsc->slice_width;
 
 	/*
 	 * minimum number of initial line pixels is a sum of:
@@ -1808,16 +1808,16 @@ dpu_encoder_dsc_initial_line_calc(struct msm_display_dsc_config *dsc,
 	 * 5. 6 additional pixels as the output of the rate buffer is
 	 *    48 bits wide
 	 */
-	ssm_delay = ((dsc->drm->bits_per_component < 10) ? 84 : 92);
-	total_pixels = ssm_delay * 3 + dsc->drm->initial_xmit_delay + 47;
+	ssm_delay = ((dsc->bits_per_component < 10) ? 84 : 92);
+	total_pixels = ssm_delay * 3 + dsc->initial_xmit_delay + 47;
 	if (soft_slice_per_enc > 1)
 		total_pixels += (ssm_delay * 3);
-	return DIV_ROUND_UP(total_pixels, dsc->drm->slice_width);
+	return DIV_ROUND_UP(total_pixels, dsc->slice_width);
 }
 
 static void dpu_encoder_dsc_pipe_cfg(struct dpu_hw_dsc *hw_dsc,
 				     struct dpu_hw_pingpong *hw_pp,
-				     struct msm_display_dsc_config *dsc,
+				     struct drm_dsc_config *dsc,
 				     u32 common_mode,
 				     u32 initial_lines)
 {
@@ -1835,7 +1835,7 @@ static void dpu_encoder_dsc_pipe_cfg(struct dpu_hw_dsc *hw_dsc,
 }
 
 static void dpu_encoder_prep_dsc(struct dpu_encoder_virt *dpu_enc,
-				 struct msm_display_dsc_config *dsc)
+				 struct drm_dsc_config *dsc)
 {
 	/* coding only for 2LM, 2enc, 1 dsc config */
 	struct dpu_encoder_phys *enc_master = dpu_enc->cur_master;
@@ -1858,14 +1858,15 @@ static void dpu_encoder_prep_dsc(struct dpu_encoder_virt *dpu_enc,
 		}
 	}
 
-	pic_width = dsc->drm->pic_width;
+	dsc_common_mode = 0;
+	pic_width = dsc->pic_width;
 
 	dsc_common_mode = DSC_MODE_MULTIPLEX | DSC_MODE_SPLIT_PANEL;
 	if (enc_master->intf_mode == INTF_MODE_VIDEO)
 		dsc_common_mode |= DSC_MODE_VIDEO;
 
-	this_frame_slices = pic_width / dsc->drm->slice_width;
-	intf_ip_w = this_frame_slices * dsc->drm->slice_width;
+	this_frame_slices = pic_width / dsc->slice_width;
+	intf_ip_w = this_frame_slices * dsc->slice_width;
 
 	/*
 	 * dsc merge case: when using 2 encoders for the same stream,
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h +1 -1
index d4d1ecd416e3..9e7236ef34e6 100644
@@ -36,7 +36,7 @@ struct msm_display_info {
 	uint32_t h_tile_instance[MAX_H_TILES_PER_DISPLAY];
 	bool is_cmd_mode;
 	bool is_te_using_watchdog_timer;
-	struct msm_display_dsc_config *dsc;
+	struct drm_dsc_config *dsc;
 };
 
 /**
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c +37 -37

133 lines not on this page · raw message

drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h +2 -2
index 45e4118f1fa2..c0b77fe1a696 100644
@@ -31,7 +31,7 @@ struct dpu_hw_dsc_ops {
 	 * @initial_lines: amount of initial lines to be used
 	 */
 	void (*dsc_config)(struct dpu_hw_dsc *hw_dsc,
-			   struct msm_display_dsc_config *dsc,
+			   struct drm_dsc_config *dsc,
 			   u32 mode,
 			   u32 initial_lines);
 
@@ -41,7 +41,7 @@ struct dpu_hw_dsc_ops {
 	 * @dsc: panel dsc parameters
 	 */
 	void (*dsc_config_thresh)(struct dpu_hw_dsc *hw_dsc,
-				  struct msm_display_dsc_config *dsc);
+				  struct drm_dsc_config *dsc);
 };
 
 struct dpu_hw_dsc {
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c +1 -1
index c99c7a218ddb..af5e027eb86f 100644
@@ -582,7 +582,7 @@ static int _dpu_kms_initialize_dsi(struct drm_device *dev,
 		info.h_tile_instance[info.num_of_h_tiles++] = i;
 		info.is_cmd_mode = msm_dsi_is_cmd_mode(priv->dsi[i]);
 
-		info.dsc = msm_dsi_get_dsc_config(priv->dsi[i]);
+		info.dsc = msm_dsi_get_dsc_config(priv->dsi[i])->drm;
 
 		if (msm_dsi_is_bonded_dsi(priv->dsi[i]) && priv->dsi[other]) {
 			rc = msm_dsi_modeset_init(priv->dsi[other], dev, encoder);
Signature · 1 line
2.35.1
author maintainer
#270 lore raw

PATCH 271/1073 drm/msm/dpu1: Account for DSCs bits_per_pixel having 4 fractional bits

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit d3c1a8663d0ddb74eaa51121ccbb8340739a12a8 ]

According to the comment this DPU register contains the bits per pixel as a 6.4 fractional value, conveniently matching the contents of bits_per_pixel in struct drm_dsc_config which also uses 4 fractional bits. However, the downstream source this implementation was copy-pasted from has its bpp field stored _without_ fractional part.

This makes the entire convoluted math obsolete as it is impossible to pull those 4 fractional bits out of thin air, by somehow trying to reuse the lowest 2 bits of a non-fractional bpp (lsb = bpp % 4??).

The rest of the code merely attempts to keep the integer part a multiple of 4, which is rendered useless thanks to data |= dsc->bits_per_pixel << 12; already filling up those bits anyway (but not on downstream).

Fixes c110cfd1753e ("drm/msm/disp/dpu1: Add support for DSC")

Patchwork: https://patchwork.freedesktop.org/patch/508946/

---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c | 11 ++---------
 1 file changed, 2 insertions(+), 9 deletions(-)
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c +2 -9
index f2ddcfb6f7ee..3662df698dae 100644
@@ -42,7 +42,7 @@ static void dpu_hw_dsc_config(struct dpu_hw_dsc *hw_dsc,
 			      u32 initial_lines)
 {
 	struct dpu_hw_blk_reg_map *c = &hw_dsc->hw;
-	u32 data, lsb, bpp;
+	u32 data;
 	u32 slice_last_group_size;
 	u32 det_thresh_flatness;
 	bool is_cmd_mode = !(mode & DSC_MODE_VIDEO);
@@ -56,14 +56,7 @@ static void dpu_hw_dsc_config(struct dpu_hw_dsc *hw_dsc,
 	data = (initial_lines << 20);
 	data |= ((slice_last_group_size - 1) << 18);
 	/* bpp is 6.4 format, 4 LSBs bits are for fractional part */
-	data |= dsc->bits_per_pixel << 12;
-	lsb = dsc->bits_per_pixel % 4;
-	bpp = dsc->bits_per_pixel / 4;
-	bpp *= 4;
-	bpp <<= 4;
-	bpp |= lsb;
-
-	data |= bpp << 8;
+	data |= (dsc->bits_per_pixel << 8);
 	data |= (dsc->block_pred_enable << 7);
 	data |= (dsc->line_buf_depth << 3);
 	data |= (dsc->simple_422 << 2);
Signature · 1 line
2.35.1
author maintainer
#271 lore raw

PATCH 272/1073 drm/msm/dsi: use drm_dsc_config instead of msm_display_dsc_config

In reply to Greg Kroah-Hartman

From: Dmitry Baryshkov <[email protected]>

[ Upstream commit 4b2b1b3674f80ed786e73d8e24c19e7129257ad8 ]

There is no need to use the struct msm_display_dsc_config wrapper inside the dsi driver, use the struct drm_dsc_config directly to pass pps data.

Patchwork: https://patchwork.freedesktop.org/patch/493341/

Stable-dep-of: 01a907980e0b ("drm/msm/dsi: Remove useless math in DSC calculations")

---
 drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c |   2 +-
 drivers/gpu/drm/msm/dsi/dsi.c           |   2 +-
 drivers/gpu/drm/msm/dsi/dsi.h           |   2 +-
 drivers/gpu/drm/msm/dsi/dsi_host.c      | 157 +++++++++++-------------
 drivers/gpu/drm/msm/msm_drv.h           |   9 +-
 5 files changed, 79 insertions(+), 93 deletions(-)
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c +1 -1
index af5e027eb86f..c99c7a218ddb 100644
@@ -582,7 +582,7 @@ static int _dpu_kms_initialize_dsi(struct drm_device *dev,
 		info.h_tile_instance[info.num_of_h_tiles++] = i;
 		info.is_cmd_mode = msm_dsi_is_cmd_mode(priv->dsi[i]);
 
-		info.dsc = msm_dsi_get_dsc_config(priv->dsi[i])->drm;
+		info.dsc = msm_dsi_get_dsc_config(priv->dsi[i]);
 
 		if (msm_dsi_is_bonded_dsi(priv->dsi[i]) && priv->dsi[other]) {
 			rc = msm_dsi_modeset_init(priv->dsi[other], dev, encoder);
drivers/gpu/drm/msm/dsi/dsi.c +1 -1
index 3db85b5c0feb..31e452ede71f 100644
@@ -21,7 +21,7 @@ bool msm_dsi_is_cmd_mode(struct msm_dsi *msm_dsi)
 	return !(host_flags & MIPI_DSI_MODE_VIDEO);
 }
 
-struct msm_display_dsc_config *msm_dsi_get_dsc_config(struct msm_dsi *msm_dsi)
+struct drm_dsc_config *msm_dsi_get_dsc_config(struct msm_dsi *msm_dsi)
 {
 	return msm_dsi_host_get_dsc_config(msm_dsi->host);
 }
drivers/gpu/drm/msm/dsi/dsi.h +1 -1
index 580a1e6358bf..df46cdda1b43 100644
@@ -154,7 +154,7 @@ int dsi_calc_clk_rate_v2(struct msm_dsi_host *msm_host, bool is_bonded_dsi);
 int dsi_calc_clk_rate_6g(struct msm_dsi_host *msm_host, bool is_bonded_dsi);
 void msm_dsi_host_snapshot(struct msm_disp_state *disp_state, struct mipi_dsi_host *host);
 void msm_dsi_host_test_pattern_en(struct mipi_dsi_host *host);
-struct msm_display_dsc_config *msm_dsi_host_get_dsc_config(struct mipi_dsi_host *host);
+struct drm_dsc_config *msm_dsi_host_get_dsc_config(struct mipi_dsi_host *host);
 
 /* dsi phy */
 struct msm_dsi_phy;
drivers/gpu/drm/msm/dsi/dsi_host.c +74 -83

286 lines not on this page · raw message

drivers/gpu/drm/msm/msm_drv.h +2 -7
index 80da0d3cfdc1..03e5b6863319 100644
@@ -96,11 +96,6 @@ struct msm_drm_thread {
 	struct kthread_worker *worker;
 };
 
-/* DSC config */
-struct msm_display_dsc_config {
-	struct drm_dsc_config *drm;
-};
-
 struct msm_drm_private {
 
 	struct drm_device *dev;
@@ -290,7 +285,7 @@ void msm_dsi_snapshot(struct msm_disp_state *disp_state, struct msm_dsi *msm_dsi
 bool msm_dsi_is_cmd_mode(struct msm_dsi *msm_dsi);
 bool msm_dsi_is_bonded_dsi(struct msm_dsi *msm_dsi);
 bool msm_dsi_is_master_dsi(struct msm_dsi *msm_dsi);
-struct msm_display_dsc_config *msm_dsi_get_dsc_config(struct msm_dsi *msm_dsi);
+struct drm_dsc_config *msm_dsi_get_dsc_config(struct msm_dsi *msm_dsi);
 #else
 static inline void __init msm_dsi_register(void)
 {
@@ -320,7 +315,7 @@ static inline bool msm_dsi_is_master_dsi(struct msm_dsi *msm_dsi)
 	return false;
 }
 
-static inline struct msm_display_dsc_config *msm_dsi_get_dsc_config(struct msm_dsi *msm_dsi)
+static inline struct drm_dsc_config *msm_dsi_get_dsc_config(struct msm_dsi *msm_dsi)
 {
 	return NULL;
 }
Signature · 1 line
2.35.1
author maintainer
#272 lore raw

PATCH 273/1073 drm/msm/dsi: Remove useless math in DSC calculations

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit 01a907980e0be3310f18c7d4955968f3b28e7147 ]

Multiplying a value by 2 and adding 1 to it always results in a value that is uneven, and that 1 gets truncated immediately when performing integer division by 2 again. There is no "rounding" possible here.

After that target_bpp_x16 is used to store a multiplication of bits_per_pixel by 16 which is only ever read to immediately be divided by 16 again, and is elided in much the same way.

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508932/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 10 +---------
 1 file changed, 1 insertion(+), 9 deletions(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +1 -9
index 15e108be1901..843521c9cdcf 100644
@@ -1849,7 +1849,6 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	int hrd_delay;
 	int pre_num_extra_mux_bits, num_extra_mux_bits;
 	int slice_bits;
-	int target_bpp_x16;
 	int data;
 	int final_value, final_scale;
 	int i;
@@ -1929,14 +1928,7 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	data = 2048 * (dsc->rc_model_size - dsc->initial_offset + num_extra_mux_bits);
 	dsc->slice_bpg_offset = DIV_ROUND_UP(data, groups_total);
 
-	/* bpp * 16 + 0.5 */
-	data = dsc->bits_per_pixel * 16;
-	data *= 2;
-	data++;
-	data /= 2;
-	target_bpp_x16 = data;
-
-	data = (dsc->initial_xmit_delay * target_bpp_x16) / 16;
+	data = dsc->initial_xmit_delay * dsc->bits_per_pixel;
 	final_value =  dsc->rc_model_size - data + num_extra_mux_bits;
 	dsc->final_offset = final_value;
 
Signature · 1 line
2.35.1
author maintainer
#273 lore raw

PATCH 274/1073 drm/msm/dsi: Remove repeated calculation of slice_per_intf

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit 170ffca836dd9f1a0219c4f67554d408fa2b5912 ]

slice_per_intf is already computed for intf_width, which holds the same value as hdisplay.

Fixes 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")

Patchwork: https://patchwork.freedesktop.org/patch/508933/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +2 -4
index 843521c9cdcf..1bce664a4eed 100644
@@ -917,7 +917,7 @@ static void dsi_ctrl_config(struct msm_dsi_host *msm_host, bool enable,
 static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mode, u32 hdisplay)
 {
 	struct drm_dsc_config *dsc = msm_host->dsc;
-	u32 reg, intf_width, reg_ctrl, reg_ctrl2;
+	u32 reg, reg_ctrl, reg_ctrl2;
 	u32 slice_per_intf, total_bytes_per_intf;
 	u32 pkt_per_line;
 	u32 bytes_in_slice;
@@ -926,8 +926,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	/* first calculate dsc parameters and then program
 	 * compress mode registers
 	 */
-	intf_width = hdisplay;
-	slice_per_intf = DIV_ROUND_UP(intf_width, dsc->slice_width);
+	slice_per_intf = DIV_ROUND_UP(hdisplay, dsc->slice_width);
 
 	/* If slice_per_pkt is greater than slice_per_intf
 	 * then default to 1. This can happen during partial
@@ -936,7 +935,6 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	if (slice_per_intf > dsc->slice_count)
 		dsc->slice_count = 1;
 
-	slice_per_intf = DIV_ROUND_UP(hdisplay, dsc->slice_width);
 	bytes_in_slice = DIV_ROUND_UP(dsc->slice_width * dsc->bits_per_pixel, 8);
 
 	dsc->slice_chunk_size = bytes_in_slice;
Signature · 1 line
2.35.1
author maintainer
#274 lore raw

PATCH 275/1073 drm/msm/dsi: Use DIV_ROUND_UP instead of conditional increment on modulo

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit 1e8196103bd02a396b45c8f6188541634a47fce2 ]

This exact same math is used to compute bytes_in_slice above in dsi_update_dsc_timing(), also used to fill slice_chunk_size.

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508935/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +1 -3
index 1bce664a4eed..3459cac6f770 100644
@@ -1894,9 +1894,7 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	 * params are calculated
 	 */
 	groups_per_line = DIV_ROUND_UP(dsc->slice_width, 3);
-	dsc->slice_chunk_size = dsc->slice_width * dsc->bits_per_pixel / 8;
-	if ((dsc->slice_width * dsc->bits_per_pixel) % 8)
-		dsc->slice_chunk_size++;
+	dsc->slice_chunk_size = DIV_ROUND_UP(dsc->slice_width * dsc->bits_per_pixel, 8);
 
 	/* rbs-min */
 	min_rate_buffer_size =  dsc->rc_model_size - dsc->initial_offset +
Signature · 1 line
2.35.1
author maintainer
#275 lore raw

PATCH 276/1073 drm/msm/dsi: Reuse earlier computed dsc->slice_chunk_size

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit e443459e2e6b8e0d3187dd0d09ef7fcea87531d2 ]

dsi_populate_dsc_params() is called prior to dsi_update_dsc_timing() and already computes a value for slice_chunk_size, whose value doesn't need to be recomputed and re-set here.

Fixes 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")

Patchwork: https://patchwork.freedesktop.org/patch/508934/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 9 ++-------
 1 file changed, 2 insertions(+), 7 deletions(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +2 -7
index 3459cac6f770..a99c54556f51 100644
@@ -920,7 +920,6 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	u32 reg, reg_ctrl, reg_ctrl2;
 	u32 slice_per_intf, total_bytes_per_intf;
 	u32 pkt_per_line;
-	u32 bytes_in_slice;
 	u32 eol_byte_num;
 
 	/* first calculate dsc parameters and then program
@@ -935,11 +934,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 	if (slice_per_intf > dsc->slice_count)
 		dsc->slice_count = 1;
 
-	bytes_in_slice = DIV_ROUND_UP(dsc->slice_width * dsc->bits_per_pixel, 8);
-
-	dsc->slice_chunk_size = bytes_in_slice;
-
-	total_bytes_per_intf = bytes_in_slice * slice_per_intf;
+	total_bytes_per_intf = dsc->slice_chunk_size * slice_per_intf;
 
 	eol_byte_num = total_bytes_per_intf % 3;
 	pkt_per_line = slice_per_intf / dsc->slice_count;
@@ -965,7 +960,7 @@ static void dsi_update_dsc_timing(struct msm_dsi_host *msm_host, bool is_cmd_mod
 		reg_ctrl |= reg;
 
 		reg_ctrl2 &= ~DSI_COMMAND_COMPRESSION_MODE_CTRL2_STREAM0_SLICE_WIDTH__MASK;
-		reg_ctrl2 |= DSI_COMMAND_COMPRESSION_MODE_CTRL2_STREAM0_SLICE_WIDTH(bytes_in_slice);
+		reg_ctrl2 |= DSI_COMMAND_COMPRESSION_MODE_CTRL2_STREAM0_SLICE_WIDTH(dsc->slice_chunk_size);
 
 		dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL, reg_ctrl);
 		dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL2, reg_ctrl2);
Signature · 1 line
2.35.1
author maintainer
#276 lore raw

PATCH 277/1073 drm/msm/dsi: Appropriately set dsc->mux_word_size based on bpc

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit 0ca870ca304d3449b2ccdc3f0bad9843ff1519f0 ]

This field is currently unread but will come into effect when duplicated code below is migrated to call drm_dsc_compute_rc_parameters(), which uses the bpc-dependent value of the local variable mux_words_size in much the same way.

The hardcoded constant seems to be a remnant from the /* bpc 8 */ comment right above, indicating that this group of field assignments is applicable to bpc = 8 exclusively and should probably bail out on different bpc values, until constants for other bpc values are added (or the current ones are confirmed to be correct across multiple bpc's).

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508943/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +1 -1
index a99c54556f51..5e5eb1a10f94 100644
@@ -1873,6 +1873,7 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	if (dsc->bits_per_component == 12)
 		mux_words_size = 64;
 
+	dsc->mux_word_size = mux_words_size;
 	dsc->initial_xmit_delay = 512;
 	dsc->initial_scale_value = 32;
 	dsc->first_line_bpg_offset = 12;
@@ -1883,7 +1884,6 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	dsc->flatness_max_qp = 12;
 	dsc->rc_quant_incr_limit0 = 11;
 	dsc->rc_quant_incr_limit1 = 11;
-	dsc->mux_word_size = DSC_MUX_WORD_SIZE_8_10_BPC;
 
 	/* FIXME: need to call drm_dsc_compute_rc_parameters() so that rest of
 	 * params are calculated
Signature · 1 line
2.35.1
author maintainer
#277 lore raw

PATCH 278/1073 drm/msm/dsi: Migrate to drm_dsc_compute_rc_parameters()

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit c3a1aabce2d4087255de90100c3dad492e7d925c ]

As per the FIXME this code is entirely duplicate with what is already provided inside drm_dsc_compute_rc_parameters(), supposedly because that function was yielding "incorrect" results while in reality the panel driver(s?) used for testing were providing incorrect parameters.

For example, this code from downstream assumed dsc->bits_per_pixel to contain an integer value, whereas the upstream drm_dsc_config struct stores it with 4 fractional bits. drm_dsc_compute_rc_parameters() already accounts for this feat while the panel driver used for testing
[1] wasn't, hence making drm_dsc_compute_rc_parameters() seem like it was returning an incorrect result.
Other users of dsc->bits_per_pixel inside dsi_populate_dsc_params() also treat it in the same erroneous way, and will be addressed in a separate patch.
In the end, using drm_dsc_compute_rc_parameters() spares both a lot of duplicate code and erratic behaviour.

[1]: https://git.linaro.org/people/vinod.koul/kernel.git/commit/?h=topic/pixel3_5.18-rc1&id=1d7d98ad564f1ec69e7525e07418918d90f247a1

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508939/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 64 +++---------------------------
 1 file changed, 6 insertions(+), 58 deletions(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +6 -58
index 5e5eb1a10f94..0c80d0797a6a 100644
@@ -21,6 +21,7 @@
 
 #include <video/mipi_display.h>
 
+#include <drm/display/drm_dsc_helper.h>
 #include <drm/drm_of.h>
 
 #include "dsi.h"
@@ -1836,14 +1837,6 @@ static char bpg_offset[DSC_NUM_BUF_RANGES] = {
 
 static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 {
-	int mux_words_size;
-	int groups_per_line, groups_total;
-	int min_rate_buffer_size;
-	int hrd_delay;
-	int pre_num_extra_mux_bits, num_extra_mux_bits;
-	int slice_bits;
-	int data;
-	int final_value, final_scale;
 	int i;
 
 	dsc->rc_model_size = 8192;
@@ -1869,11 +1862,11 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	if (dsc->bits_per_pixel != 8)
 		dsc->initial_offset = 2048;	/* bpp = 12 */
 
-	mux_words_size = 48;		/* bpc == 8/10 */
-	if (dsc->bits_per_component == 12)
-		mux_words_size = 64;
+	if (dsc->bits_per_component <= 10)
+		dsc->mux_word_size = DSC_MUX_WORD_SIZE_8_10_BPC;
+	else
+		dsc->mux_word_size = DSC_MUX_WORD_SIZE_12_BPC;
 
-	dsc->mux_word_size = mux_words_size;
 	dsc->initial_xmit_delay = 512;
 	dsc->initial_scale_value = 32;
 	dsc->first_line_bpg_offset = 12;
@@ -1885,52 +1878,7 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 	dsc->rc_quant_incr_limit0 = 11;
 	dsc->rc_quant_incr_limit1 = 11;
 
-	/* FIXME: need to call drm_dsc_compute_rc_parameters() so that rest of
-	 * params are calculated
-	 */
-	groups_per_line = DIV_ROUND_UP(dsc->slice_width, 3);
-	dsc->slice_chunk_size = DIV_ROUND_UP(dsc->slice_width * dsc->bits_per_pixel, 8);
-
-	/* rbs-min */
-	min_rate_buffer_size =  dsc->rc_model_size - dsc->initial_offset +
-				dsc->initial_xmit_delay * dsc->bits_per_pixel +
-				groups_per_line * dsc->first_line_bpg_offset;
-
-	hrd_delay = DIV_ROUND_UP(min_rate_buffer_size, dsc->bits_per_pixel);
-
-	dsc->initial_dec_delay = hrd_delay - dsc->initial_xmit_delay;
-
-	dsc->initial_scale_value = 8 * dsc->rc_model_size /
-				       (dsc->rc_model_size - dsc->initial_offset);
-
-	slice_bits = 8 * dsc->slice_chunk_size * dsc->slice_height;
-
-	groups_total = groups_per_line * dsc->slice_height;
-
-	data = dsc->first_line_bpg_offset * 2048;
-
-	dsc->nfl_bpg_offset = DIV_ROUND_UP(data, (dsc->slice_height - 1));
-
-	pre_num_extra_mux_bits = 3 * (mux_words_size + (4 * dsc->bits_per_component + 4) - 2);
-
-	num_extra_mux_bits = pre_num_extra_mux_bits - (mux_words_size -
-			     ((slice_bits - pre_num_extra_mux_bits) % mux_words_size));
-
-	data = 2048 * (dsc->rc_model_size - dsc->initial_offset + num_extra_mux_bits);
-	dsc->slice_bpg_offset = DIV_ROUND_UP(data, groups_total);
-
-	data = dsc->initial_xmit_delay * dsc->bits_per_pixel;
-	final_value =  dsc->rc_model_size - data + num_extra_mux_bits;
-	dsc->final_offset = final_value;
-
-	final_scale = 8 * dsc->rc_model_size / (dsc->rc_model_size - final_value);
-
-	data = (final_scale - 9) * (dsc->nfl_bpg_offset + dsc->slice_bpg_offset);
-	dsc->scale_increment_interval = (2048 * dsc->final_offset) / data;
-
-	dsc->scale_decrement_interval = groups_per_line / (dsc->initial_scale_value - 8);
-
-	return 0;
+	return drm_dsc_compute_rc_parameters(dsc);
 }
 
 static int dsi_host_parse_dt(struct msm_dsi_host *msm_host)
Signature · 1 line
2.35.1
author maintainer
#278 lore raw

PATCH 279/1073 drm/msm/dsi: Account for DSCs bits_per_pixel having 4 fractional bits

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit d2c277c61986942e99680cb67ce26423d0f42f11 ]

drm_dsc_config's bits_per_pixel field holds a fractional value with 4 bits, which all panel drivers should adhere to for drm_dsc_pps_payload_pack() to generate a valid payload. All code in the DSI driver here seems to assume that this field doesn't contain any fractional bits, hence resulting in the wrong values being computed. Since none of the calculations leave any room for fractional bits or seem to indicate any possible area of support, disallow such values altogether. calculate_rc_params() in intel_vdsc.c performs an identical bitshift to get at this integer value.

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508938/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +14 -5
index 0c80d0797a6a..27fef5169bed 100644
@@ -34,7 +34,7 @@
 
 #define DSI_RESET_TOGGLE_DELAY_MS 20
 
-static int dsi_populate_dsc_params(struct drm_dsc_config *dsc);
+static int dsi_populate_dsc_params(struct msm_dsi_host *msm_host, struct drm_dsc_config *dsc);
 
 static int dsi_get_version(const void __iomem *base, u32 *major, u32 *minor)
 {
@@ -984,6 +984,7 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi)
 	u32 va_end = va_start + mode->vdisplay;
 	u32 hdisplay = mode->hdisplay;
 	u32 wc;
+	int ret;
 
 	DBG("");
 
@@ -1019,7 +1020,9 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi)
 		/* we do the calculations for dsc parameters here so that
 		 * panel can use these parameters
 		 */
-		dsi_populate_dsc_params(dsc);
+		ret = dsi_populate_dsc_params(msm_host, dsc);
+		if (ret)
+			return;
 
 		/* Divide the display by 3 but keep back/font porch and
 		 * pulse width same
@@ -1835,9 +1838,15 @@ static char bpg_offset[DSC_NUM_BUF_RANGES] = {
 	2, 0, 0, -2, -4, -6, -8, -8, -8, -10, -10, -12, -12, -12, -12
 };
 
-static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
+static int dsi_populate_dsc_params(struct msm_dsi_host *msm_host, struct drm_dsc_config *dsc)
 {
 	int i;
+	u16 bpp = dsc->bits_per_pixel >> 4;
+
+	if (dsc->bits_per_pixel & 0xf) {
+		DRM_DEV_ERROR(&msm_host->pdev->dev, "DSI does not support fractional bits_per_pixel\n");
+		return -EINVAL;
+	}
 
 	dsc->rc_model_size = 8192;
 	dsc->first_line_bpg_offset = 12;
@@ -1858,8 +1867,8 @@ static int dsi_populate_dsc_params(struct drm_dsc_config *dsc)
 		dsc->rc_range_params[i].range_bpg_offset = bpg_offset[i];
 	}
 
-	dsc->initial_offset = 6144; /* Not bpp 12 */
-	if (dsc->bits_per_pixel != 8)
+	dsc->initial_offset = 6144;		/* Not bpp 12 */
+	if (bpp != 8)
 		dsc->initial_offset = 2048;	/* bpp = 12 */
 
 	if (dsc->bits_per_component <= 10)
Signature · 1 line
2.35.1
author maintainer
#279 lore raw

PATCH 280/1073 drm/msm/dsi: Disallow 8 BPC DSC configuration for alternative BPC values

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit d053fbc449c47517b1f6516dbce2f917f2a9f51d ]

According to the /* bpc 8 */ comment below only values for a bits_per_component of 8 are currently hardcoded in place. This is further confirmed by downstream sources [1] containing different constants for other BPC values (and different initial_offset too, with an extra dependency on bits_per_pixel). Prevent future mishaps by explicitly disallowing any other bits_per_component value until the right parameters are put in place and tested.

[1]: https://git.codelinaro.org/clo/la/platform/vendor/opensource/display-drivers/-/blob/DISPLAY.LA.2.0.r1-08000-WAIPIO.0/msm/sde_dsc_helper.c#L110-139

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508942/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/gpu/drm/msm/dsi/dsi_host.c +5 -0
index 27fef5169bed..c5805416854f 100644
@@ -1848,6 +1848,11 @@ static int dsi_populate_dsc_params(struct msm_dsi_host *msm_host, struct drm_dsc
 		return -EINVAL;
 	}
 
+	if (dsc->bits_per_component != 8) {
+		DRM_DEV_ERROR(&msm_host->pdev->dev, "DSI does not support bits_per_component != 8 yet\n");
+		return -EOPNOTSUPP;
+	}
+
 	dsc->rc_model_size = 8192;
 	dsc->first_line_bpg_offset = 12;
 	dsc->rc_edge_factor = 6;
Signature · 1 line
2.35.1
author maintainer
#280 lore raw

PATCH 281/1073 drm/msm/dsi: Prevent signed BPG offsets from bleeding into adjacent bits

In reply to Greg Kroah-Hartman

From: Marijn Suijten <[email protected]>

[ Upstream commit cc84b66be223d36a3d10d59d68ba647e72db3099 ]

The bpg_offset array contains negative BPG offsets which fill the full 8 bits of a char thanks to two's complement: this however results in those bits bleeding into the next field when the value is packed into DSC PPS by the drm_dsc_helper function, which only expects range_bpg_offset to contain 6-bit wide values. As a consequence random slices appear corrupted on-screen (tested on a Sony Tama Akatsuki device with sdm845).

Use AND operators to limit these two's complement values to 6 bits, similar to the AMD and i915 drivers.

Fixes b9080324d6ca ("drm/msm/dsi: add support for dsc data")

Patchwork: https://patchwork.freedesktop.org/patch/508941/

---
 drivers/gpu/drm/msm/dsi/dsi_host.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/dsi/dsi_host.c +5 -1
index c5805416854f..cf7d5b69aac5 100644
@@ -1869,7 +1869,11 @@ static int dsi_populate_dsc_params(struct msm_dsi_host *msm_host, struct drm_dsc
 	for (i = 0; i < DSC_NUM_BUF_RANGES; i++) {
 		dsc->rc_range_params[i].range_min_qp = min_qp[i];
 		dsc->rc_range_params[i].range_max_qp = max_qp[i];
-		dsc->rc_range_params[i].range_bpg_offset = bpg_offset[i];
+		/*
+		 * Range BPG Offset contains two's-complement signed values that fill
+		 * 8 bits, yet the registers and DCS PPS field are only 6 bits wide.
+		 */
+		dsc->rc_range_params[i].range_bpg_offset = bpg_offset[i] & DSC_RANGE_BPG_OFFSET_MASK;
 	}
 
 	dsc->initial_offset = 6144;		/* Not bpp 12 */
Signature · 1 line
2.35.1
author maintainer
#281 lore raw

PATCH 282/1073 media: rkvdec: Add required padding

In reply to Greg Kroah-Hartman

From: Andrzej Pietrasiewicz <[email protected]>

[ Upstream commit 00c47aa85bb26450edc6059c3d245de062e60b5d ]

The addresses of two elements of the segmap[][] member are passed to the hardware which expects 128-bit aligned addresses. However, without this patch offsetof(struct rkvdec_vp9_priv_tbl, segmap[0]) is an odd number (2421) but the hardware just ignores the 5 least significant bits of the address. As a result, the hardware writes the segmentation map to incorrect locations.

Inserting 11 bytes of padding corrects this situation by making the said addresses divisible by 16 (i.e. aligned on a 128-bit boundary).

Fixes f25709c4ff15 ("media: rkvdec: Add the VP9 backend")
---
 drivers/staging/media/rkvdec/rkvdec-vp9.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/staging/media/rkvdec/rkvdec-vp9.c +3 -0
index d8c1c0db15c7..cfae99b40ccb 100644
@@ -84,6 +84,8 @@ struct rkvdec_vp9_probs {
 		struct rkvdec_vp9_inter_frame_probs inter;
 		struct rkvdec_vp9_intra_only_frame_probs intra_only;
 	};
+	/* 128 bit alignment */
+	u8 padding1[11];
 };
 
 /* Data structure describing auxiliary buffer format. */
@@ -1006,6 +1008,7 @@ static int rkvdec_vp9_start(struct rkvdec_ctx *ctx)
 
 	ctx->priv = vp9_ctx;
 
+	BUILD_BUG_ON(sizeof(priv_tbl->probs) % 16); /* ensure probs size is 128-bit aligned */
 	priv_tbl = dma_alloc_coherent(rkvdec->dev, sizeof(*priv_tbl),
 				      &vp9_ctx->priv_tbl.dma, GFP_KERNEL);
 	if (!priv_tbl) {
Signature · 1 line
2.35.1
author maintainer
#282 lore raw

PATCH 283/1073 media: vivid: fix compose size exceed boundary

In reply to Greg Kroah-Hartman

From: Liu Shixin <[email protected]>

[ Upstream commit 94a7ad9283464b75b12516c5512541d467cefcf8 ]

syzkaller found a bug:

 BUG: unable to handle page fault for address: ffffc9000a3b1000
 #PF: supervisor write access in kernel mode
 #PF: error_code(0x0002) - not-present page
 PGD 100000067 P4D 100000067 PUD 10015f067 PMD 1121ca067 PTE 0
 Oops: 0002 [#1] PREEMPT SMP
 CPU: 0 PID: 23489 Comm: vivid-000-vid-c Not tainted 6.1.0-rc1+ #512
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
 RIP: 0010:memcpy_erms+0x6/0x10
[...]
 Call Trace:
  <TASK>
  ? tpg_fill_plane_buffer+0x856/0x15b0
  vivid_fillbuff+0x8ac/0x1110
  vivid_thread_vid_cap_tick+0x361/0xc90
  vivid_thread_vid_cap+0x21a/0x3a0
  kthread+0x143/0x180
  ret_from_fork+0x1f/0x30
  </TASK>

This is because we forget to check boundary after adjust compose->height int V4L2_SEL_TGT_CROP case. Add v4l2_rect_map_inside() to fix this problem for this case.

Fixes ef834f7836ec ("[media] vivid: add the video capture and output parts")
---
 drivers/media/test-drivers/vivid/vivid-vid-cap.c | 1 +
 1 file changed, 1 insertion(+)
drivers/media/test-drivers/vivid/vivid-vid-cap.c +1 -0
index 99139a8cd4c4..331a3f4286d2 100644
@@ -961,6 +961,7 @@ int vivid_vid_cap_s_selection(struct file *file, void *fh, struct v4l2_selection
 			if (dev->has_compose_cap) {
 				v4l2_rect_set_min_size(compose, &min_rect);
 				v4l2_rect_set_max_size(compose, &max_rect);
+				v4l2_rect_map_inside(compose, &fmt);
 			}
 			dev->fmt_cap_rect = fmt;
 			tpg_s_buf_height(&dev->tpg, fmt.height);
Signature · 1 line
2.35.1
author maintainer
#283 lore raw

PATCH 284/1073 media: platform: exynos4-is: fix return value check in fimc_md_probe()

In reply to Greg Kroah-Hartman

From: Yang Yingliang <[email protected]>

[ Upstream commit e38e42c078da4af962d322b97e726dcb2f184e3f ]

devm_pinctrl_get() may return ERR_PTR(-EPROBE_DEFER), add a minus sign to fix it.

Fixes 4163851f7b99 ("[media] s5p-fimc: Use pinctrl API for camera ports configuration")
---
 drivers/media/platform/samsung/exynos4-is/media-dev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/platform/samsung/exynos4-is/media-dev.c +1 -1
index 412213b0c384..383a1e0ab912 100644
@@ -1472,7 +1472,7 @@ static int fimc_md_probe(struct platform_device *pdev)
 	pinctrl = devm_pinctrl_get(dev);
 	if (IS_ERR(pinctrl)) {
 		ret = PTR_ERR(pinctrl);
-		if (ret != EPROBE_DEFER)
+		if (ret != -EPROBE_DEFER)
 			dev_err(dev, "Failed to get pinctrl: %d\n", ret);
 		goto err_clk;
 	}
Signature · 1 line
2.35.1
author maintainer
#284 lore raw

PATCH 285/1073 bpf: propagate precision in ALU/ALU64 operations

In reply to Greg Kroah-Hartman

From: Andrii Nakryiko <[email protected]>

[ Upstream commit a3b666bfa9c9edc05bca62a87abafe0936bd7f97 ]

When processing ALU/ALU64 operations (apart from BPF_MOV, which is handled correctly already; and BPF_NEG and BPF_END are special and don't have source register), if destination register is already marked precise, this causes problem with potentially missing precision tracking for the source register. E.g., when we have r1 >>= r5 and r1 is marked precise, but r5 isn't, this will lead to r5 staying as imprecise. This is due to the precision backtracking logic stopping early when it sees r1 is already marked precise. If r1 wasn't precise, we'd keep backtracking and would add r5 to the set of registers that need to be marked precise. So there is a discrepancy here which can lead to invalid and incompatible states matched due to lack of precision marking on r5. If r1 wasn't precise, precision backtracking would correctly mark both r1 and r5 as precise.

This is simple to fix, though. During the forward instruction simulation pass, for arithmetic operations of scalar <op>= scalar form (where <op> is ALU or ALU64 operations), if destination register is already precise, mark source register as precise. This applies only when both involved registers are SCALARs. ptr += scalar and scalar += ptr cases are already handled correctly.

This does have (negative) effect on some selftest programs and few Cilium programs. ~/baseline-tmp-results.csv are veristat results with this patch, while ~/baseline-results.csv is without it. See post scriptum for instructions on how to make Cilium programs testable with veristat. Correctness has a price.

$ ./veristat -C -e file,prog,insns,states ~/baseline-results.csv ~/baseline-tmp-results.csv | grep -v '+0'
File                     Program               Total insns (A)  Total insns (B)  Total insns (DIFF)  Total states (A)  Total states (B)  Total states (DIFF)
-----------------------  --------------------  ---------------  ---------------  ------------------  ----------------  ----------------  -------------------
bpf_cubic.bpf.linked1.o  bpf_cubic_cong_avoid              997             1700      +703 (+70.51%)                62                90        +28 (+45.16%)
test_l4lb.bpf.linked1.o  balancer_ingress                 4559             5469      +910 (+19.96%)               118               126          +8 (+6.78%)
-----------------------  --------------------  ---------------  ---------------  ------------------  ----------------  ----------------  -------------------
$ ./veristat -C -e file,prog,verdict,insns,states ~/baseline-results-cilium.csv ~/baseline-tmp-results-cilium.csv | grep -v '+0'
File           Program                         Total insns (A)  Total insns (B)  Total insns (DIFF)  Total states (A)  Total states (B)  Total states (DIFF)
-------------  ------------------------------  ---------------  ---------------  ------------------  ----------------  ----------------  -------------------
bpf_host.o     tail_nodeport_nat_ingress_ipv6             4448             5261      +813 (+18.28%)               234               247         +13 (+5.56%)
bpf_host.o     tail_nodeport_nat_ipv6_egress              3396             3446        +50 (+1.47%)               201               203          +2 (+1.00%)
bpf_lxc.o      tail_nodeport_nat_ingress_ipv6             4448             5261      +813 (+18.28%)               234               247         +13 (+5.56%)
bpf_overlay.o  tail_nodeport_nat_ingress_ipv6             4448             5261      +813 (+18.28%)               234               247         +13 (+5.56%)
bpf_xdp.o      tail_lb_ipv4                              71736            73442      +1706 (+2.38%)              4295              4370         +75 (+1.75%)
-------------  ------------------------------  ---------------  ---------------  ------------------  ----------------  ----------------  -------------------

P.S. To make Cilium ([0]) programs libbpf-compatible and thus veristat-loadable, apply changes from topmost commit in [1], which does minimal changes to Cilium source code, mostly around SEC() annotations and BPF map definitions.

[0] https://github.com/cilium/cilium/
[1] https://github.com/anakryiko/cilium/commits/libbpf-friendliness

---
 kernel/bpf/verifier.c | 5 +++++
 1 file changed, 5 insertions(+)
kernel/bpf/verifier.c +5 -0
index 95479562a64a..05414615c008 100644
@@ -9061,6 +9061,11 @@ static int adjust_reg_min_max_vals(struct bpf_verifier_env *env,
 				return err;
 			return adjust_ptr_min_max_vals(env, insn,
 						       dst_reg, src_reg);
+		} else if (dst_reg->precise) {
+			/* if dst_reg is precise, src_reg should be precise as well */
+			err = mark_chain_precision(env, insn->src_reg);
+			if (err)
+				return err;
 		}
 	} else {
 		/* Pretend the src is a reg with a known value, since we only
Signature · 1 line
2.35.1
author maintainer
#285 lore raw

PATCH 286/1073 bpf: propagate precision across all frames, not just the last one

In reply to Greg Kroah-Hartman

From: Andrii Nakryiko <[email protected]>

[ Upstream commit 529409ea92d590659be487ba0839710329bd8074 ]

When equivalent completed state is found and it has additional precision restrictions, BPF verifier propagates precision to currently-being-verified state chain (i.e., including parent states) so that if some of the states in the chain are not yet completed, necessary precision restrictions are enforced.

Unfortunately, right now this happens only for the last frame (deepest active subprogram's frame), not all the frames. This can lead to incorrect matching of states due to missing precision marker. Currently this doesn't seem possible as BPF verifier forces everything to precise when validated BPF program has any subprograms. But with the next patch lifting this restriction, this becomes problematic.

In fact, without this fix, we'll start getting failure in one of the existing test_verifier test cases:

#906/p precise: cross frame pruning FAIL
Unexpected success to load!
verification time 48 usec
stack depth 0+0
processed 26 insns (limit 1000000) max_states_per_insn 3 total_states 17 peak_states 17 mark_read 8

This patch adds precision propagation across all frames.

---
 kernel/bpf/verifier.c | 71 ++++++++++++++++++++++++-------------------
 1 file changed, 39 insertions(+), 32 deletions(-)
kernel/bpf/verifier.c +39 -32
index 05414615c008..7a1ca0e58043 100644
@@ -2751,7 +2751,7 @@ static void mark_all_scalars_precise(struct bpf_verifier_env *env,
 		}
 }
 
-static int __mark_chain_precision(struct bpf_verifier_env *env, int regno,
+static int __mark_chain_precision(struct bpf_verifier_env *env, int frame, int regno,
 				  int spi)
 {
 	struct bpf_verifier_state *st = env->cur_state;
@@ -2768,7 +2768,7 @@ static int __mark_chain_precision(struct bpf_verifier_env *env, int regno,
 	if (!env->bpf_capable)
 		return 0;
 
-	func = st->frame[st->curframe];
+	func = st->frame[frame];
 	if (regno >= 0) {
 		reg = &func->regs[regno];
 		if (reg->type != SCALAR_VALUE) {
@@ -2849,7 +2849,7 @@ static int __mark_chain_precision(struct bpf_verifier_env *env, int regno,
 			break;
 
 		new_marks = false;
-		func = st->frame[st->curframe];
+		func = st->frame[frame];
 		bitmap_from_u64(mask, reg_mask);
 		for_each_set_bit(i, mask, 32) {
 			reg = &func->regs[i];
@@ -2915,12 +2915,17 @@ static int __mark_chain_precision(struct bpf_verifier_env *env, int regno,
 
 static int mark_chain_precision(struct bpf_verifier_env *env, int regno)
 {
-	return __mark_chain_precision(env, regno, -1);
+	return __mark_chain_precision(env, env->cur_state->curframe, regno, -1);
 }
 
-static int mark_chain_precision_stack(struct bpf_verifier_env *env, int spi)
+static int mark_chain_precision_frame(struct bpf_verifier_env *env, int frame, int regno)
 {
-	return __mark_chain_precision(env, -1, spi);
+	return __mark_chain_precision(env, frame, regno, -1);
+}
+
+static int mark_chain_precision_stack_frame(struct bpf_verifier_env *env, int frame, int spi)
+{
+	return __mark_chain_precision(env, frame, -1, spi);
 }
 
 static bool is_spillable_regtype(enum bpf_reg_type type)
@@ -11702,34 +11707,36 @@ static int propagate_precision(struct bpf_verifier_env *env,
 {
 	struct bpf_reg_state *state_reg;
 	struct bpf_func_state *state;
-	int i, err = 0;
+	int i, err = 0, fr;
 
-	state = old->frame[old->curframe];
-	state_reg = state->regs;
-	for (i = 0; i < BPF_REG_FP; i++, state_reg++) {
-		if (state_reg->type != SCALAR_VALUE ||
-		    !state_reg->precise)
-			continue;
-		if (env->log.level & BPF_LOG_LEVEL2)
-			verbose(env, "propagating r%d\n", i);
-		err = mark_chain_precision(env, i);
-		if (err < 0)
-			return err;
-	}
+	for (fr = old->curframe; fr >= 0; fr--) {
+		state = old->frame[fr];
+		state_reg = state->regs;
+		for (i = 0; i < BPF_REG_FP; i++, state_reg++) {
+			if (state_reg->type != SCALAR_VALUE ||
+			    !state_reg->precise)
+				continue;
+			if (env->log.level & BPF_LOG_LEVEL2)
+				verbose(env, "frame %d: propagating r%d\n", i, fr);
+			err = mark_chain_precision_frame(env, fr, i);
+			if (err < 0)
+				return err;
+		}
 
-	for (i = 0; i < state->allocated_stack / BPF_REG_SIZE; i++) {
-		if (!is_spilled_reg(&state->stack[i]))
-			continue;
-		state_reg = &state->stack[i].spilled_ptr;
-		if (state_reg->type != SCALAR_VALUE ||
-		    !state_reg->precise)
-			continue;
-		if (env->log.level & BPF_LOG_LEVEL2)
-			verbose(env, "propagating fp%d\n",
-				(-i - 1) * BPF_REG_SIZE);
-		err = mark_chain_precision_stack(env, i);
-		if (err < 0)
-			return err;
+		for (i = 0; i < state->allocated_stack / BPF_REG_SIZE; i++) {
+			if (!is_spilled_reg(&state->stack[i]))
+				continue;
+			state_reg = &state->stack[i].spilled_ptr;
+			if (state_reg->type != SCALAR_VALUE ||
+			    !state_reg->precise)
+				continue;
+			if (env->log.level & BPF_LOG_LEVEL2)
+				verbose(env, "frame %d: propagating fp%d\n",
+					(-i - 1) * BPF_REG_SIZE, fr);
+			err = mark_chain_precision_stack_frame(env, fr, i);
+			if (err < 0)
+				return err;
+		}
 	}
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#286 lore raw

PATCH 287/1073 clk: qcom: gcc-ipq806x: use parent_data for the last remaining entry

In reply to Greg Kroah-Hartman

From: Dmitry Baryshkov <[email protected]>

[ Upstream commit 55307e522cc7a4dddc3d231ca5cb7e68e9668f66 ]

Use parent_data for the last remaining entry (pll4). This clock is provided by the lcc device.

Fixes cb02866f9a74 ("clk: qcom: gcc-ipq806x: convert parent_names to parent_data")
---
 drivers/clk/qcom/gcc-ipq806x.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/clk/qcom/gcc-ipq806x.c +3 -1
index 718de17a1e60..6447f3e81b55 100644
@@ -79,7 +79,9 @@ static struct clk_regmap pll4_vote = {
 	.enable_mask = BIT(4),
 	.hw.init = &(struct clk_init_data){
 		.name = "pll4_vote",
-		.parent_names = (const char *[]){ "pll4" },
+		.parent_data = &(const struct clk_parent_data){
+			.fw_name = "pll4", .name = "pll4",
+		},
 		.num_parents = 1,
 		.ops = &clk_pll_vote_ops,
 	},
Signature · 1 line
2.35.1
author maintainer
#287 lore raw

PATCH 288/1073 clk: qcom: dispcc-sm6350: Add CLK_OPS_PARENT_ENABLE to pixel&byte src

In reply to Greg Kroah-Hartman

From: Konrad Dybcio <[email protected]>

[ Upstream commit 92039e8c080c63748f8e133e7cfad33a75daefb6 ]

Add the CLK_OPS_PARENT_ENABLE flag to pixel and byte clk srcs to ensure set_rate can succeed.

Fixes 837519775f1d ("clk: qcom: Add display clock controller driver for SM6350")
---
 drivers/clk/qcom/dispcc-sm6350.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/clk/qcom/dispcc-sm6350.c +2 -2
index 0c3c2e26ede9..ea6f54ed846e 100644
@@ -306,7 +306,7 @@ static struct clk_rcg2 disp_cc_mdss_pclk0_clk_src = {
 		.name = "disp_cc_mdss_pclk0_clk_src",
 		.parent_data = disp_cc_parent_data_5,
 		.num_parents = ARRAY_SIZE(disp_cc_parent_data_5),
-		.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE,
+		.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE | CLK_OPS_PARENT_ENABLE,
 		.ops = &clk_pixel_ops,
 	},
 };
@@ -385,7 +385,7 @@ static struct clk_branch disp_cc_mdss_byte0_clk = {
 				&disp_cc_mdss_byte0_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
-			.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE,
+			.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE | CLK_OPS_PARENT_ENABLE,
 			.ops = &clk_branch2_ops,
 		},
 	},
Signature · 1 line
2.35.1
author maintainer
#288 lore raw

PATCH 290/1073 mtd: Fix device name leak when register device failed in add_mtd_device()

In reply to Greg Kroah-Hartman

From: Zhang Xiaoxu <[email protected]>

[ Upstream commit 895d68a39481a75c680aa421546931fb11942fa6 ]

There is a kmemleak when register device failed:
unreferenced object 0xffff888101aab550 (size 8):

    comm "insmod", pid 3922, jiffies 4295277753 (age 925.408s)
    hex dump (first 8 bytes):
      6d 74 64 30 00 88 ff ff                          mtd0....
    backtrace:
      [<00000000bde26724>] __kmalloc_node_track_caller+0x4e/0x150
      [<000000003c32b416>] kvasprintf+0xb0/0x130
      [<000000001f7a8f15>] kobject_set_name_vargs+0x2f/0xb0
      [<000000006e781163>] dev_set_name+0xab/0xe0
      [<00000000e30d0c78>] add_mtd_device+0x4bb/0x700
      [<00000000f3d34de7>] mtd_device_parse_register+0x2ac/0x3f0
      [<00000000c0d88488>] 0xffffffffa0238457
      [<00000000b40d0922>] 0xffffffffa02a008f
      [<0000000023d17b9d>] do_one_initcall+0x87/0x2a0
      [<00000000770f6ca6>] do_init_module+0xdf/0x320
      [<000000007b6768fe>] load_module+0x2f98/0x3330
      [<00000000346bed5a>] __do_sys_finit_module+0x113/0x1b0
      [<00000000674c2290>] do_syscall_64+0x35/0x80
      [<000000004c6a8d97>] entry_SYSCALL_64_after_hwframe+0x46/0xb0

If register device failed, should call put_device() to give up the reference.

---
 drivers/mtd/mtdcore.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/mtd/mtdcore.c +3 -1
index 477707bcad97..cc7e1fd1ef10 100644
@@ -723,8 +723,10 @@ int add_mtd_device(struct mtd_info *mtd)
 	mtd_check_of_node(mtd);
 	of_node_get(mtd_get_of_node(mtd));
 	error = device_register(&mtd->dev);
-	if (error)
+	if (error) {
+		put_device(&mtd->dev);
 		goto fail_added;
+	}
 
 	/* Add the nvmem provider */
 	error = mtd_nvmem_add(mtd);
Signature · 1 line
2.35.1
author maintainer
#289 lore raw

PATCH 291/1073 mtd: core: fix possible resource leak in init_mtd()

In reply to Greg Kroah-Hartman

From: Gaosheng Cui <[email protected]>

[ Upstream commit 1aadf01e5076b9ab6bf294b9622335c651314895 ]

I got the error report while inject fault in init_mtd():

sysfs: cannot create duplicate filename '/devices/virtual/bdi/mtd-0'

Call Trace:
 <TASK>
 dump_stack_lvl+0x67/0x83
 sysfs_warn_dup+0x60/0x70
 sysfs_create_dir_ns+0x109/0x120
 kobject_add_internal+0xce/0x2f0
 kobject_add+0x98/0x110
 device_add+0x179/0xc00
 device_create_groups_vargs+0xf4/0x100
 device_create+0x7b/0xb0
 bdi_register_va.part.13+0x58/0x2d0
 bdi_register+0x9b/0xb0
 init_mtd+0x62/0x171 [mtd]
 do_one_initcall+0x6c/0x3c0
 do_init_module+0x58/0x222
 load_module+0x268e/0x27d0
 __do_sys_finit_module+0xd5/0x140
 do_syscall_64+0x37/0x90
 entry_SYSCALL_64_after_hwframe+0x63/0xcd
 </TASK>

kobject_add_internal failed for mtd-0 with -EEXIST, don't try to register
things with the same name in the same directory.
Error registering mtd class or bdi: -17

If init_mtdchar() fails in init_mtd(), mtd_bdi will not be unregistered, as a result, we can't load the mtd module again, to fix this by calling bdi_unregister(mtd_bdi) after out_procfs label.

Fixes 445caaa20c4d ("mtd: Allocate bdi objects dynamically")
---
 drivers/mtd/mtdcore.c | 1 +
 1 file changed, 1 insertion(+)
drivers/mtd/mtdcore.c +1 -0
index cc7e1fd1ef10..37050c551880 100644
@@ -2452,6 +2452,7 @@ static int __init init_mtd(void)
 out_procfs:
 	if (proc_mtd)
 		remove_proc_entry("mtd", NULL);
+	bdi_unregister(mtd_bdi);
 	bdi_put(mtd_bdi);
 err_bdi:
 	class_unregister(&mtd_class);
Signature · 1 line
2.35.1
author maintainer
#290 lore raw

PATCH 292/1073 Input: joystick - fix Kconfig warning for JOYSTICK_ADC

In reply to Greg Kroah-Hartman

From: Randy Dunlap <[email protected]>

[ Upstream commit 6100a19c4fcfe154dd32f8a8ef4e8c0b1f607c75 ]

Fix a Kconfig warning for JOYSTICK_ADC by also selecting IIO_BUFFER.

WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- JOYSTICK_ADC [=y] && INPUT [=y] && INPUT_JOYSTICK [=y] && IIO [=y]

Fixes 2c2b364fddd5 ("Input: joystick - add ADC attached joystick driver.")
---
 drivers/input/joystick/Kconfig | 1 +
 1 file changed, 1 insertion(+)
drivers/input/joystick/Kconfig +1 -0
index 9dcf3f51f2dd..04ca3d1c2816 100644
@@ -46,6 +46,7 @@ config JOYSTICK_A3D
 config JOYSTICK_ADC
 	tristate "Simple joystick connected over ADC"
 	depends on IIO
+	select IIO_BUFFER
 	select IIO_BUFFER_CB
 	help
 	  Say Y here if you have a simple joystick connected over ADC.
Signature · 1 line
2.35.1
author maintainer
#291 lore raw

PATCH 293/1073 wifi: rsi: Fix handling of 802.3 EAPOL frames sent via control port

In reply to Greg Kroah-Hartman

From: Marek Vasut <[email protected]>

[ Upstream commit b8f6efccbb9dc0ff5dee7e20d69a4747298ee603 ]

When using wpa_supplicant v2.10, this driver is no longer able to associate with any AP and fails in the EAPOL 4-way handshake while sending the 2/4 message to the AP. The problem is not present in wpa_supplicant v2.9 or older. The problem stems from HostAP commit 144314eaa ("wpa_supplicant: Send EAPOL frames over nl80211 where available") which changes the way EAPOL frames are sent, from them being send at L2 frames to them being sent via nl80211 control port.

An EAPOL frame sent as L2 frame is passed to the WiFi driver with skb->protocol ETH_P_PAE, while EAPOL frame sent via nl80211 control port has skb->protocol set to ETH_P_802_3 . The later happens in ieee80211_tx_control_port(), where the EAPOL frame is encapsulated into 802.3 frame.

The rsi_91x driver handles ETH_P_PAE EAPOL frames as high-priority frames and sends them via highest-priority transmit queue, while the ETH_P_802_3 frames are sent as regular frames. The EAPOL 4-way handshake frames must be sent as highest-priority, otherwise the 4-way handshake times out.

Therefore, to fix this problem, inspect the skb control flags and if flag IEEE80211_TX_CTRL_PORT_CTRL_PROTO is set, assume this is an EAPOL frame and transmit the frame via high-priority queue just like other ETH_P_PAE frames.

Fixes 0eb42586cf87 ("rsi: data packet descriptor enhancements")
---
 drivers/net/wireless/rsi/rsi_91x_core.c | 4 +++-
 drivers/net/wireless/rsi/rsi_91x_hal.c  | 6 +++++-
 2 files changed, 8 insertions(+), 2 deletions(-)
drivers/net/wireless/rsi/rsi_91x_core.c +3 -1
index 0f3a80f66b61..ead4d4e04328 100644
@@ -466,7 +466,9 @@ void rsi_core_xmit(struct rsi_common *common, struct sk_buff *skb)
 							      tid, 0);
 			}
 		}
-		if (skb->protocol == cpu_to_be16(ETH_P_PAE)) {
+
+		if (IEEE80211_SKB_CB(skb)->control.flags &
+		    IEEE80211_TX_CTRL_PORT_CTRL_PROTO) {
 			q_num = MGMT_SOFT_Q;
 			skb->priority = q_num;
 		}
drivers/net/wireless/rsi/rsi_91x_hal.c +5 -1
index c61f83a7333b..c7460fbba014 100644
@@ -162,12 +162,16 @@ int rsi_prepare_data_desc(struct rsi_common *common, struct sk_buff *skb)
 	u8 header_size;
 	u8 vap_id = 0;
 	u8 dword_align_bytes;
+	bool tx_eapol;
 	u16 seq_num;
 
 	info = IEEE80211_SKB_CB(skb);
 	vif = info->control.vif;
 	tx_params = (struct skb_info *)info->driver_data;
 
+	tx_eapol = IEEE80211_SKB_CB(skb)->control.flags &
+		   IEEE80211_TX_CTRL_PORT_CTRL_PROTO;
+
 	header_size = FRAME_DESC_SZ + sizeof(struct rsi_xtended_desc);
 	if (header_size > skb_headroom(skb)) {
 		rsi_dbg(ERR_ZONE, "%s: Unable to send pkt\n", __func__);
@@ -231,7 +235,7 @@ int rsi_prepare_data_desc(struct rsi_common *common, struct sk_buff *skb)
 		}
 	}
 
-	if (skb->protocol == cpu_to_be16(ETH_P_PAE)) {
+	if (tx_eapol) {
 		rsi_dbg(INFO_ZONE, "*** Tx EAPOL ***\n");
 
 		data_desc->frame_info = cpu_to_le16(RATE_INFO_ENABLE);
Signature · 1 line
2.35.1
author maintainer
#292 lore raw

PATCH 294/1073 media: camss: Clean up received buffers on failed start of streaming

In reply to Greg Kroah-Hartman

From: Vladimir Zapolskiy <[email protected]>

[ Upstream commit c8f3582345e6a69da65ab588f7c4c2d1685b0e80 ]

It is required to return the received buffers, if streaming can not be started. For instance media_pipeline_start() may fail with EPIPE, if a link validation between entities is not passed, and in such a case a user gets a kernel warning:

  WARNING: CPU: 1 PID: 520 at drivers/media/common/videobuf2/videobuf2-core.c:1592 vb2_start_streaming+0xec/0x160
  <snip>
  Call trace:
   vb2_start_streaming+0xec/0x160
   vb2_core_streamon+0x9c/0x1a0
   vb2_ioctl_streamon+0x68/0xbc
   v4l_streamon+0x30/0x3c
   __video_do_ioctl+0x184/0x3e0
   video_usercopy+0x37c/0x7b0
   video_ioctl2+0x24/0x40
   v4l2_ioctl+0x4c/0x70

The fix is to correct the error path in video_start_streaming() of camss.

Fixes 0ac2586c410f ("media: camss: Add files which handle the video device nodes")
---
 drivers/media/platform/qcom/camss/camss-video.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/media/platform/qcom/camss/camss-video.c +2 -1
index 290df04c4d02..a25fffb0b8ec 100644
@@ -495,7 +495,7 @@ static int video_start_streaming(struct vb2_queue *q, unsigned int count)
 
 	ret = media_pipeline_start(&vdev->entity, &video->pipe);
 	if (ret < 0)
-		return ret;
+		goto flush_buffers;
 
 	ret = video_check_format(video);
 	if (ret < 0)
@@ -524,6 +524,7 @@ static int video_start_streaming(struct vb2_queue *q, unsigned int count)
 error:
 	media_pipeline_stop(&vdev->entity);
 
+flush_buffers:
 	video->ops->flush_buffers(video, VB2_BUF_STATE_QUEUED);
 
 	return ret;
Signature · 1 line
2.35.1
author maintainer
#293 lore raw

PATCH 295/1073 media: camss: Do not attach an already attached power domain on MSM8916 platform

In reply to Greg Kroah-Hartman

From: Vladimir Zapolskiy <[email protected]>

[ Upstream commit 3d658980e6dac2af6a024fdb6ded3d7bc44dc9ff ]

The change to dynamically allocated power domains neglected a case of CAMSS on MSM8916 platform, where a single VFE power domain is neither attached, linked or managed in runtime in any way explicitly.

This is a special case and it shall be kept as is, because the power domain management is done outside of the driver, and it's very different in comparison to all other platforms supported by CAMSS.

Fixes 6b1814e26989 ("media: camss: Allocate power domain resources dynamically")
---
 drivers/media/platform/qcom/camss/camss.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/media/platform/qcom/camss/camss.c +11 -0
index 1118c40886d5..a157cac72e0a 100644
@@ -1465,6 +1465,14 @@ static int camss_configure_pd(struct camss *camss)
 		return camss->genpd_num;
 	}
 
+	/*
+	 * If a platform device has just one power domain, then it is attached
+	 * at platform_probe() level, thus there shall be no need and even no
+	 * option to attach it again, this is the case for CAMSS on MSM8916.
+	 */
+	if (camss->genpd_num == 1)
+		return 0;
+
 	camss->genpd = devm_kmalloc_array(dev, camss->genpd_num,
 					  sizeof(*camss->genpd), GFP_KERNEL);
 	if (!camss->genpd)
@@ -1698,6 +1706,9 @@ void camss_delete(struct camss *camss)
 
 	pm_runtime_disable(camss->dev);
 
+	if (camss->genpd_num == 1)
+		return;
+
 	for (i = 0; i < camss->genpd_num; i++) {
 		device_link_del(camss->genpd_link[i]);
 		dev_pm_domain_detach(camss->genpd[i], true);
Signature · 1 line
2.35.1
author maintainer
#294 lore raw

PATCH 296/1073 clk: renesas: r8a779f0: Fix HSCIF parent clocks

In reply to Greg Kroah-Hartman

From: Wolfram Sang <[email protected]>

[ Upstream commit c258e3ab639112d8f5ae9df9a873750ae2623ce2 ]

As serial communication requires a clean clock signal, the High Speed Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock that is not affected by Spread Spectrum or Fractional Multiplication.

Hence change the parent clocks for the HSCIF modules from the S0D3_PER clock to the SASYNCPERD1 clock (which has the same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.

---
 drivers/clk/renesas/r8a779f0-cpg-mssr.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/clk/renesas/r8a779f0-cpg-mssr.c +4 -4
index cd80b6084ece..90cac3f8b2ed 100644
@@ -120,10 +120,10 @@ static const struct cpg_core_clk r8a779f0_core_clks[] __initconst = {
 };
 
 static const struct mssr_mod_clk r8a779f0_mod_clks[] __initconst = {
-	DEF_MOD("hscif0",	514,	R8A779F0_CLK_S0D3),
-	DEF_MOD("hscif1",	515,	R8A779F0_CLK_S0D3),
-	DEF_MOD("hscif2",	516,	R8A779F0_CLK_S0D3),
-	DEF_MOD("hscif3",	517,	R8A779F0_CLK_S0D3),
+	DEF_MOD("hscif0",	514,	R8A779F0_CLK_SASYNCPERD1),
+	DEF_MOD("hscif1",	515,	R8A779F0_CLK_SASYNCPERD1),
+	DEF_MOD("hscif2",	516,	R8A779F0_CLK_SASYNCPERD1),
+	DEF_MOD("hscif3",	517,	R8A779F0_CLK_SASYNCPERD1),
 	DEF_MOD("i2c0",		518,	R8A779F0_CLK_S0D6_PER),
 	DEF_MOD("i2c1",		519,	R8A779F0_CLK_S0D6_PER),
 	DEF_MOD("i2c2",		520,	R8A779F0_CLK_S0D6_PER),
Signature · 1 line
2.35.1
author maintainer
#295 lore raw

PATCH 297/1073 clk: renesas: r8a779f0: Fix SCIF parent clocks

In reply to Greg Kroah-Hartman

From: Wolfram Sang <[email protected]>

[ Upstream commit 2e0d7d3eabce3babae1fd66d7650e00c848a3b45 ]

As serial communication requires a clean clock signal, the Serial Communication Interfaces with FIFO (SCIF) are clocked by a clock that is not affected by Spread Spectrum or Fractional Multiplication.

Hence change the parent clocks for the SCIF modules from the S0D12_PER clock to the SASYNCPERD4 clock (which has the same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.

Fixes 24aaff6a6ce4 ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
---
 drivers/clk/renesas/r8a779f0-cpg-mssr.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/clk/renesas/r8a779f0-cpg-mssr.c +4 -4
index 90cac3f8b2ed..b7936f422c27 100644
@@ -132,10 +132,10 @@ static const struct mssr_mod_clk r8a779f0_mod_clks[] __initconst = {
 	DEF_MOD("i2c5",		523,	R8A779F0_CLK_S0D6_PER),
 	DEF_MOD("pcie0",	624,	R8A779F0_CLK_S0D2),
 	DEF_MOD("pcie1",	625,	R8A779F0_CLK_S0D2),
-	DEF_MOD("scif0",	702,	R8A779F0_CLK_S0D12_PER),
-	DEF_MOD("scif1",	703,	R8A779F0_CLK_S0D12_PER),
-	DEF_MOD("scif3",	704,	R8A779F0_CLK_S0D12_PER),
-	DEF_MOD("scif4",	705,	R8A779F0_CLK_S0D12_PER),
+	DEF_MOD("scif0",	702,	R8A779F0_CLK_SASYNCPERD4),
+	DEF_MOD("scif1",	703,	R8A779F0_CLK_SASYNCPERD4),
+	DEF_MOD("scif3",	704,	R8A779F0_CLK_SASYNCPERD4),
+	DEF_MOD("scif4",	705,	R8A779F0_CLK_SASYNCPERD4),
 	DEF_MOD("sdhi0",        706,    R8A779F0_CLK_SD0),
 	DEF_MOD("sys-dmac0",	709,	R8A779F0_CLK_S0D3_PER),
 	DEF_MOD("sys-dmac1",	710,	R8A779F0_CLK_S0D3_PER),
Signature · 1 line
2.35.1
author maintainer
#296 lore raw

PATCH 298/1073 virt/sev-guest: Add a MODULE_ALIAS

In reply to Greg Kroah-Hartman

From: Cole Robinson <[email protected]>

[ Upstream commit 2874529b3513bdc90299c90f40713602da685e35 ]

Autoload the driver when, for example, SNP init code creates the corresponding platform device.

[ bp: Rewrite commit message. ]

---
 drivers/virt/coco/sev-guest/sev-guest.c | 1 +
 1 file changed, 1 insertion(+)
drivers/virt/coco/sev-guest/sev-guest.c +1 -0
index 1ea6d2e5b218..99d6062afe72 100644
@@ -800,3 +800,4 @@ MODULE_AUTHOR("Brijesh Singh <[email protected]>");
 MODULE_LICENSE("GPL");
 MODULE_VERSION("1.0.0");
 MODULE_DESCRIPTION("AMD SEV Guest Driver");
+MODULE_ALIAS("platform:sev-guest");
Signature · 1 line
2.35.1
author maintainer
#297 lore raw

PATCH 299/1073 net, proc: Provide PROC_FS=n fallback for proc_create_net_single_write()

In reply to Greg Kroah-Hartman

From: David Howells <[email protected]>

[ Upstream commit c3d96f690a790074b508fe183a41e36a00cd7ddd ]

Provide a CONFIG_PROC_FS=n fallback for proc_create_net_single_write().

Also provide a fallback for proc_create_net_data_write().

Fixes 564def71765c ("proc: Add a way to make network proc files writable")
cc Marc Dionne <[email protected]>
---
 include/linux/proc_fs.h | 2 ++
 1 file changed, 2 insertions(+)
include/linux/proc_fs.h +2 -0
index 81d6e4ec2294..0260f5ea98fe 100644
@@ -208,8 +208,10 @@ static inline void proc_remove(struct proc_dir_entry *de) {}
 static inline int remove_proc_subtree(const char *name, struct proc_dir_entry *parent) { return 0; }
 
 #define proc_create_net_data(name, mode, parent, ops, state_size, data) ({NULL;})
+#define proc_create_net_data_write(name, mode, parent, ops, write, state_size, data) ({NULL;})
 #define proc_create_net(name, mode, parent, state_size, ops) ({NULL;})
 #define proc_create_net_single(name, mode, parent, show, data) ({NULL;})
+#define proc_create_net_single_write(name, mode, parent, show, write, data) ({NULL;})
 
 static inline struct pid *tgid_pidfd_to_pid(const struct file *file)
 {
Signature · 1 line
2.35.1
#298 lore raw

Re: [PATCH 6.0 0299/1073] net, proc: Provide PROC_FS=n fallback for proc_create_net_single_write()

This series was applied to bpf/bpf.git (master) by Arnaldo Carvalho de Melo <[email protected]>:

Hello:

This series was applied to bpf/bpf.git (master)
by Arnaldo Carvalho de Melo <[email protected]>:

Quoted 9 lines · On Wed, 28 Dec 2022 15:31:27 +0100 you wrote:

From: David Howells <[email protected]>

[ Upstream commit c3d96f690a790074b508fe183a41e36a00cd7ddd ]

Provide a CONFIG_PROC_FS=n fallback for proc_create_net_single_write().

Also provide a fallback for proc_create_net_data_write().

[...]

Here is the summary with links:
- [6.0,0299/1073] net, proc: Provide PROC_FS=n fallback for proc_create_net_single_write() (no matching commit)
- [6.0,0742/1073] perf trace: Return error if a system call doesnt exist

    https://git.kernel.org/bpf/bpf/c/d4223e1776c3
  - [6.0,0743/1073] perf trace: Use macro RAW_SYSCALL_ARGS_NUM to replace number
    https://git.kernel.org/bpf/bpf/c/eadcab4c7a66
  - [6.0,0744/1073] perf trace: Handle failure when trace point folder is missed
    https://git.kernel.org/bpf/bpf/c/03e9a5d8eb55
  - [6.0,0756/1073] perf off_cpu: Fix a typo in BTF tracepoint name, it should be btf_trace_sched_switch
    https://git.kernel.org/bpf/bpf/c/167b266bf66c

- [6.0,0930/1073] igb: Do not free q_vector unless new one was allocated (no matching commit)

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
author maintainer
#299 lore raw

PATCH 300/1073 rxrpc: Fix ack.bufferSize to be 0 when generating an ack

In reply to Greg Kroah-Hartman

From: David Howells <[email protected]>

[ Upstream commit 8889a711f9b4dcf4dd1330fa493081beebd118c9 ]

ack.bufferSize should be set to 0 when generating an ack.

Fixes 8d94aa381dab ("rxrpc: Calls shouldn't hold socket refs")
cc Marc Dionne <[email protected]>
---
 net/rxrpc/output.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/rxrpc/output.c +1 -1
index 9683617db704..08c117bc083e 100644
@@ -93,7 +93,7 @@ static size_t rxrpc_fill_out_ack(struct rxrpc_connection *conn,
 	*_hard_ack = hard_ack;
 	*_top = top;
 
-	pkt->ack.bufferSpace	= htons(8);
+	pkt->ack.bufferSpace	= htons(0);
 	pkt->ack.maxSkew	= htons(0);
 	pkt->ack.firstPacket	= htonl(hard_ack + 1);
 	pkt->ack.previousPacket	= htonl(call->ackr_highest_seq);
Signature · 1 line
2.35.1
author maintainer
#300 lore raw

PATCH 301/1073 drm: lcdif: Set and enable FIFO Panic threshold

In reply to Greg Kroah-Hartman

From: Marek Vasut <[email protected]>

[ Upstream commit e3cac8f7749f78dacdf19c00ed5862a1db52239f ]

In case the LCDIFv3 is used to drive a 4k panel via i.MX8MP HDMI bridge, the LCDIFv3 becomes susceptible to FIFO underflows, these lead to nasty flicker of the image on the panel, or image being shifted by half frame horizontally every second frame. The flicker can be easily triggered by running 3D application on top of weston compositor, like neverball or chromium. Surprisingly glmark2-es2-wayland or glmark2-es2-drm does not trigger this effect so easily.

Configure the FIFO Panic threshold register and enable the FIFO Panic mode, which internally boosts the NoC interconnect priority for LCDIFv3 transactions in case of possible underflow. This mitigates the flicker effect on 4k panels as well.

---
 drivers/gpu/drm/mxsfb/lcdif_kms.c  | 16 ++++++++++++++++
 drivers/gpu/drm/mxsfb/lcdif_regs.h |  1 +
 2 files changed, 17 insertions(+)
drivers/gpu/drm/mxsfb/lcdif_kms.c +16 -0
index 713b0d756f2a..d419c61c3407 100644
@@ -5,6 +5,7 @@
  * This code is based on drivers/gpu/drm/mxsfb/mxsfb*
  */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
@@ -167,6 +168,18 @@ static void lcdif_enable_controller(struct lcdif_drm_private *lcdif)
 {
 	u32 reg;
 
+	/* Set FIFO Panic watermarks, low 1/3, high 2/3 . */
+	writel(FIELD_PREP(PANIC0_THRES_LOW_MASK, 1 * PANIC0_THRES_MAX / 3) |
+	       FIELD_PREP(PANIC0_THRES_HIGH_MASK, 2 * PANIC0_THRES_MAX / 3),
+	       lcdif->base + LCDC_V8_PANIC0_THRES);
+
+	/*
+	 * Enable FIFO Panic, this does not generate interrupt, but
+	 * boosts NoC priority based on FIFO Panic watermarks.
+	 */
+	writel(INT_ENABLE_D1_PLANE_PANIC_EN,
+	       lcdif->base + LCDC_V8_INT_ENABLE_D1);
+
 	reg = readl(lcdif->base + LCDC_V8_DISP_PARA);
 	reg |= DISP_PARA_DISP_ON;
 	writel(reg, lcdif->base + LCDC_V8_DISP_PARA);
@@ -194,6 +207,9 @@ static void lcdif_disable_controller(struct lcdif_drm_private *lcdif)
 	reg = readl(lcdif->base + LCDC_V8_DISP_PARA);
 	reg &= ~DISP_PARA_DISP_ON;
 	writel(reg, lcdif->base + LCDC_V8_DISP_PARA);
+
+	/* Disable FIFO Panic NoC priority booster. */
+	writel(0, lcdif->base + LCDC_V8_INT_ENABLE_D1);
 }
 
 static void lcdif_reset_block(struct lcdif_drm_private *lcdif)
drivers/gpu/drm/mxsfb/lcdif_regs.h +1 -0
index 8e8bef175bf2..37f0d9a06b10 100644
@@ -252,6 +252,7 @@
 
 #define PANIC0_THRES_LOW_MASK		GENMASK(24, 16)
 #define PANIC0_THRES_HIGH_MASK		GENMASK(8, 0)
+#define PANIC0_THRES_MAX		511
 
 #define LCDIF_MIN_XRES			120
 #define LCDIF_MIN_YRES			120
Signature · 1 line
2.35.1
author maintainer
#301 lore raw

PATCH 302/1073 wifi: rtw89: use u32_encode_bits() to fill MAC quota value

In reply to Greg Kroah-Hartman

From: Ping-Ke Shih <[email protected]>

[ Upstream commit 525c06c81d75690a9b795cc62a758838c1a6b6fe ]

Coverity reported shift 16 bits could cause sign extension and might get an unexpected value. Since the input values are predefined and no this kind of case, original code is safe so far. But, still changing them to use u32_encode_bits() will be more clear and prevent mistakes in the future.

The original message of Coverity is:
Suspicious implicit sign extension: "max_cfg->cma0_dma" with type "u16" (16 bits, unsigned) is promoted in "max_cfg->cma0_dma << 16" to type "int" (32 bits, signed), then sign-extended to type "unsigned long" (64 bits, unsigned). If "max_cfg->cma0_dma << 16" is greater than 0x7FFFFFFF, the upper bits of the result will all be 1."

Addresses-Coverity-ID: 1527095 ("Integer handling issues")

Fixes e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
---
 drivers/net/wireless/realtek/rtw89/mac.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/net/wireless/realtek/rtw89/mac.c +2 -4
index 93124b815825..1afc14531194 100644
@@ -1387,10 +1387,8 @@ static int dle_mix_cfg(struct rtw89_dev *rtwdev, const struct rtw89_dle_mem *cfg
 #define INVALID_QT_WCPU U16_MAX
 #define SET_QUOTA_VAL(_min_x, _max_x, _module, _idx)			\
 	do {								\
-		val = ((_min_x) &					\
-		       B_AX_ ## _module ## _MIN_SIZE_MASK) |		\
-		      (((_max_x) << 16) &				\
-		       B_AX_ ## _module ## _MAX_SIZE_MASK);		\
+		val = u32_encode_bits(_min_x, B_AX_ ## _module ## _MIN_SIZE_MASK) | \
+		      u32_encode_bits(_max_x, B_AX_ ## _module ## _MAX_SIZE_MASK);  \
 		rtw89_write32(rtwdev,					\
 			      R_AX_ ## _module ## _QTA ## _idx ## _CFG,	\
 			      val);					\
Signature · 1 line
2.35.1
author maintainer
#302 lore raw

PATCH 303/1073 drm: rcar-du: Drop leftovers dependencies from Kconfig

In reply to Greg Kroah-Hartman

From: Laurent Pinchart <[email protected]>

[ Upstream commit 1760eb547276299ab0c6a6cd3d29469e54ade615 ]

Commit 841281fe52a7 ("drm: rcar-du: Drop LVDS device tree backward compatibility") has removed device tree overlay sources used for backward compatibility with old bindings, but forgot to remove related dependencies from Kconfig. Fix it.

Fixes 841281fe52a7 ("drm: rcar-du: Drop LVDS device tree backward compatibility")
---
 drivers/gpu/drm/rcar-du/Kconfig | 2 --
 1 file changed, 2 deletions(-)
drivers/gpu/drm/rcar-du/Kconfig +0 -2
index f6e6a6d5d987..b3c29ca7726e 100644
@@ -41,8 +41,6 @@ config DRM_RCAR_LVDS
 	depends on DRM_RCAR_USE_LVDS
 	select DRM_KMS_HELPER
 	select DRM_PANEL
-	select OF_FLATTREE
-	select OF_OVERLAY
 
 config DRM_RCAR_MIPI_DSI
 	tristate "R-Car DU MIPI DSI Encoder Support"
Signature · 1 line
2.35.1
author maintainer
#303 lore raw

PATCH 304/1073 regmap-irq: Use the new num_config_regs property in regmap_add_irq_chip_fwnode

In reply to Greg Kroah-Hartman

From: Yassine Oudjana <[email protected]>

[ Upstream commit 84498d1fb35de6ab71bdfdb6270a464fb4a0951b ]

Commit faa87ce9196d ("regmap-irq: Introduce config registers for irq types") added the num_config_regs, then commit 9edd4f5aee84 ("regmap-irq:
Deprecate type registers and virtual registers") suggested to replace num_type_reg with it. However, regmap_add_irq_chip_fwnode wasn't modified to use the new property. Later on, commit 255a03bb1bb3 ("ASoC: wcd9335:
Convert irq chip to config regs") removed the old num_type_reg property from the WCD9335 driver's struct regmap_irq_chip, causing a null pointer dereference in regmap_irq_set_type when it tried to index d->type_buf as it was never allocated in regmap_add_irq_chip_fwnode:

[   39.199374] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[   39.200006] Call trace:
[   39.200014]  regmap_irq_set_type+0x84/0x1c0
[   39.200026]  __irq_set_trigger+0x60/0x1c0
[   39.200040]  __setup_irq+0x2f4/0x78c
[   39.200051]  request_threaded_irq+0xe8/0x1a0

Use num_config_regs in regmap_add_irq_chip_fwnode instead of num_type_reg, and fall back to it if num_config_regs isn't defined to maintain backward compatibility.

Fixes faa87ce9196d ("regmap-irq: Introduce config registers for irq types")
---
 drivers/base/regmap/regmap-irq.c | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)
drivers/base/regmap/regmap-irq.c +11 -4
index 4ef9488d05cd..3de89795f584 100644
@@ -722,6 +722,7 @@ int regmap_add_irq_chip_fwnode(struct fwnode_handle *fwnode,
 	int i;
 	int ret = -ENOMEM;
 	int num_type_reg;
+	int num_regs;
 	u32 reg;
 
 	if (chip->num_regs <= 0)
@@ -796,14 +797,20 @@ int regmap_add_irq_chip_fwnode(struct fwnode_handle *fwnode,
 			goto err_alloc;
 	}
 
-	num_type_reg = chip->type_in_mask ? chip->num_regs : chip->num_type_reg;
-	if (num_type_reg) {
-		d->type_buf_def = kcalloc(num_type_reg,
+	/*
+	 * Use num_config_regs if defined, otherwise fall back to num_type_reg
+	 * to maintain backward compatibility.
+	 */
+	num_type_reg = chip->num_config_regs ? chip->num_config_regs
+			: chip->num_type_reg;
+	num_regs = chip->type_in_mask ? chip->num_regs : num_type_reg;
+	if (num_regs) {
+		d->type_buf_def = kcalloc(num_regs,
 					  sizeof(*d->type_buf_def), GFP_KERNEL);
 		if (!d->type_buf_def)
 			goto err_alloc;
 
-		d->type_buf = kcalloc(num_type_reg, sizeof(*d->type_buf),
+		d->type_buf = kcalloc(num_regs, sizeof(*d->type_buf),
 				      GFP_KERNEL);
 		if (!d->type_buf)
 			goto err_alloc;
Signature · 1 line
2.35.1
author maintainer
#304 lore raw

PATCH 305/1073 drbd: use blk_queue_max_discard_sectors helper

In reply to Greg Kroah-Hartman

From: Christoph Böhmwalder <[email protected]>

[ Upstream commit 258bea6388ac93f34561fd91064232d14e174bff ]

We currently only set q->limits.max_discard_sectors, but that is not enough. Another field, max_hw_discard_sectors, was introduced in commit 0034af036554 ("block: make /sys/block/<dev>/queue/discard_max_bytes writeable").

The difference is that max_discard_sectors can be changed from user space via sysfs, while max_hw_discard_sectors is the "hardware" upper limit.

So use this helper, which sets both.

This is also a fixup for commit 998e9cbcd615 ("drbd: cleanup decide_on_discard_support"): if discards are not supported, that does not necessarily mean we also want to disable write_zeroes.

---
 drivers/block/drbd/drbd_nl.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/block/drbd/drbd_nl.c +5 -5
index 013d355a2033..921c303a7b5c 100644
@@ -1210,6 +1210,7 @@ static void decide_on_discard_support(struct drbd_device *device,
 	struct drbd_connection *connection =
 		first_peer_device(device)->connection;
 	struct request_queue *q = device->rq_queue;
+	unsigned int max_discard_sectors;
 
 	if (bdev && !bdev_max_discard_sectors(bdev->backing_bdev))
 		goto not_supported;
@@ -1230,15 +1231,14 @@ static void decide_on_discard_support(struct drbd_device *device,
 	 * topology on all peers.
 	 */
 	blk_queue_discard_granularity(q, 512);
-	q->limits.max_discard_sectors = drbd_max_discard_sectors(connection);
-	q->limits.max_write_zeroes_sectors =
-		drbd_max_discard_sectors(connection);
+	max_discard_sectors = drbd_max_discard_sectors(connection);
+	blk_queue_max_discard_sectors(q, max_discard_sectors);
+	blk_queue_max_write_zeroes_sectors(q, max_discard_sectors);
 	return;
 
 not_supported:
 	blk_queue_discard_granularity(q, 0);
-	q->limits.max_discard_sectors = 0;
-	q->limits.max_write_zeroes_sectors = 0;
+	blk_queue_max_discard_sectors(q, 0);
 }
 
 static void fixup_write_zeroes(struct drbd_device *device, struct request_queue *q)
Signature · 1 line
2.35.1
author maintainer
#305 lore raw

PATCH 306/1073 bfq: fix waker_bfqq inconsistency crash

In reply to Greg Kroah-Hartman

From: Khazhismel Kumykov <[email protected]>

[ Upstream commit a1795c2ccb1e4c49220d2a0d381540024d71647c ]

This fixes crashes in bfq_add_bfqq_busy due to waker_bfqq being NULL, but woken_list_node still being hashed. This would happen when bfq_init_rq() expects a brand new allocated queue to be returned from bfq_get_bfqq_handle_split() and unconditionally updates waker_bfqq without resetting woken_list_node. Since we can always return oom_bfqq when attempting to allocate, we cannot assume waker_bfqq starts as NULL.

Avoid setting woken_bfqq for oom_bfqq entirely, as it's not useful.

Crashes would have a stacktrace like:

[160595.656560]  bfq_add_bfqq_busy+0x110/0x1ec
[160595.661142]  bfq_add_request+0x6bc/0x980
[160595.666602]  bfq_insert_request+0x8ec/0x1240
[160595.671762]  bfq_insert_requests+0x58/0x9c
[160595.676420]  blk_mq_sched_insert_request+0x11c/0x198
[160595.682107]  blk_mq_submit_bio+0x270/0x62c
[160595.686759]  __submit_bio_noacct_mq+0xec/0x178
[160595.691926]  submit_bio+0x120/0x184
[160595.695990]  ext4_mpage_readpages+0x77c/0x7c8
[160595.701026]  ext4_readpage+0x60/0xb0
[160595.705158]  filemap_read_page+0x54/0x114
[160595.711961]  filemap_fault+0x228/0x5f4
[160595.716272]  do_read_fault+0xe0/0x1f0
[160595.720487]  do_fault+0x40/0x1c8

Tested by injecting random failures into bfq_get_queue, crashes go away completely.

Fixes 8ef3fc3a043c ("block, bfq: make shared queues inherit wakers")
---
 block/bfq-iosched.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
block/bfq-iosched.c +7 -2
index c740b41fe0a4..68872a61706a 100644
@@ -6786,6 +6786,12 @@ static struct bfq_queue *bfq_init_rq(struct request *rq)
 				bfqq = bfq_get_bfqq_handle_split(bfqd, bic, bio,
 								 true, is_sync,
 								 NULL);
+				if (unlikely(bfqq == &bfqd->oom_bfqq))
+					bfqq_already_existing = true;
+			} else
+				bfqq_already_existing = true;
+
+			if (!bfqq_already_existing) {
 				bfqq->waker_bfqq = old_bfqq->waker_bfqq;
 				bfqq->tentative_waker_bfqq = NULL;
 
@@ -6799,8 +6805,7 @@ static struct bfq_queue *bfq_init_rq(struct request *rq)
 				if (bfqq->waker_bfqq)
 					hlist_add_head(&bfqq->woken_list_node,
 						       &bfqq->waker_bfqq->woken_list);
-			} else
-				bfqq_already_existing = true;
+			}
 		}
 	}
 
Signature · 1 line
2.35.1
author maintainer
#306 lore raw

PATCH 307/1073 drm/radeon: Add the missed acpi_put_table() to fix memory leak

In reply to Greg Kroah-Hartman

From: Hanjun Guo <[email protected]>

[ Upstream commit 10276a20be1115e1f76c189330da2992df980eee ]

When the radeon driver reads the bios information from ACPI table in radeon_acpi_vfct_bios(), it misses to call acpi_put_table() to release the ACPI memory after the init, so add acpi_put_table() properly to fix the memory leak.

v2: fix text formatting (Alex)

Fixes 268ba0a99f89 ("drm/radeon: implement ACPI VFCT vbios fetch (v3)")
---
 drivers/gpu/drm/radeon/radeon_bios.c | 18 +++++++++++-------
 1 file changed, 11 insertions(+), 7 deletions(-)
drivers/gpu/drm/radeon/radeon_bios.c +11 -7
index 33121655d50b..1d99c9a2b56e 100644
@@ -612,13 +612,14 @@ static bool radeon_acpi_vfct_bios(struct radeon_device *rdev)
 	acpi_size tbl_size;
 	UEFI_ACPI_VFCT *vfct;
 	unsigned offset;
+	bool r = false;
 
 	if (!ACPI_SUCCESS(acpi_get_table("VFCT", 1, &hdr)))
 		return false;
 	tbl_size = hdr->length;
 	if (tbl_size < sizeof(UEFI_ACPI_VFCT)) {
 		DRM_ERROR("ACPI VFCT table present but broken (too short #1)\n");
-		return false;
+		goto out;
 	}
 
 	vfct = (UEFI_ACPI_VFCT *)hdr;
@@ -631,13 +632,13 @@ static bool radeon_acpi_vfct_bios(struct radeon_device *rdev)
 		offset += sizeof(VFCT_IMAGE_HEADER);
 		if (offset > tbl_size) {
 			DRM_ERROR("ACPI VFCT image header truncated\n");
-			return false;
+			goto out;
 		}
 
 		offset += vhdr->ImageLength;
 		if (offset > tbl_size) {
 			DRM_ERROR("ACPI VFCT image truncated\n");
-			return false;
+			goto out;
 		}
 
 		if (vhdr->ImageLength &&
@@ -649,15 +650,18 @@ static bool radeon_acpi_vfct_bios(struct radeon_device *rdev)
 			rdev->bios = kmemdup(&vbios->VbiosContent,
 					     vhdr->ImageLength,
 					     GFP_KERNEL);
+			if (rdev->bios)
+				r = true;
 
-			if (!rdev->bios)
-				return false;
-			return true;
+			goto out;
 		}
 	}
 
 	DRM_ERROR("ACPI VFCT table present but broken (too short #2)\n");
-	return false;
+
+out:
+	acpi_put_table(hdr);
+	return r;
 }
 #else
 static inline bool radeon_acpi_vfct_bios(struct radeon_device *rdev)
Signature · 1 line
2.35.1
author maintainer
#307 lore raw

PATCH 308/1073 dt-bindings: pinctrl: update uart/mmc bindings for MT7986 SoC

In reply to Greg Kroah-Hartman

From: Frank Wunderlich <[email protected]>

[ Upstream commit c115e7f51e685536ecb885854bdd4b3f225ff3e4 ]

Fix mmc and uart pins after uart splitting.

Some pinmux pins of the mt7986 pinctrl driver is composed of multiple pinctrl groups, the original binding only allows one pinctrl group per dts node, this patch sets "maxItems" for these groups and add new examples to the binding documentation.

---
 .../pinctrl/mediatek,mt7986-pinctrl.yaml      | 46 +++++++++++++++++--
 1 file changed, 41 insertions(+), 5 deletions(-)
Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml +41 -5
index 4eadea55df10..41abfa94877f 100644
@@ -87,6 +87,8 @@ patternProperties:
           "wifi_led"        "led"       1, 2
           "i2c"             "i2c"       3, 4
           "uart1_0"         "uart"      7, 8, 9, 10
+          "uart1_rx_tx"     "uart"      42, 43
+          "uart1_cts_rts"   "uart"      44, 45
           "pcie_clk"        "pcie"      9
           "pcie_wake"       "pcie"      10
           "spi1_0"          "spi"       11, 12, 13, 14
@@ -98,9 +100,11 @@ patternProperties:
           "emmc_45"         "emmc"      22, 23, 24, 25, 26, 27, 28, 29, 30,
                                         31, 32
           "spi1_1"          "spi"       23, 24, 25, 26
-          "uart1_2"         "uart"      29, 30, 31, 32
+          "uart1_2_rx_tx"   "uart"      29, 30
+          "uart1_2_cts_rts" "uart"      31, 32
           "uart1_1"         "uart"      23, 24, 25, 26
-          "uart2_0"         "uart"      29, 30, 31, 32
+          "uart2_0_rx_tx"   "uart"      29, 30
+          "uart2_0_cts_rts" "uart"      31, 32
           "spi0"            "spi"       33, 34, 35, 36
           "spi0_wp_hold"    "spi"       37, 38
           "uart1_3_rx_tx"   "uart"      35, 36
@@ -153,7 +157,7 @@ patternProperties:
             then:
               properties:
                 groups:
-                  enum: [emmc, emmc_rst]
+                  enum: [emmc_45, emmc_51]
           - if:
               properties:
                 function:
@@ -217,8 +221,12 @@ patternProperties:
             then:
               properties:
                 groups:
-                  enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx,
-                         uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2]
+                  items:
+                    enum: [uart1_0, uart1_rx_tx, uart1_cts_rts, uart1_1,
+                           uart1_2_rx_tx, uart1_2_cts_rts, uart1_3_rx_tx,
+                           uart1_3_cts_rts, uart2_0_rx_tx, uart2_0_cts_rts,
+                           uart2_1, uart0, uart1, uart2]
+                  maxItems: 2
           - if:
               properties:
                 function:
@@ -348,6 +356,27 @@ examples:
         interrupt-parent = <&gic>;
         #interrupt-cells = <2>;
 
+        pcie_pins: pcie-pins {
+          mux {
+            function = "pcie";
+            groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+          };
+        };
+
+        pwm_pins: pwm-pins {
+          mux {
+            function = "pwm";
+            groups = "pwm0", "pwm1_0";
+          };
+        };
+
+        spi0_pins: spi0-pins {
+          mux {
+            function = "spi";
+            groups = "spi0", "spi0_wp_hold";
+          };
+        };
+
         uart1_pins: uart1-pins {
           mux {
             function = "uart";
@@ -355,6 +384,13 @@ examples:
           };
         };
 
+        uart1_3_pins: uart1-3-pins {
+          mux {
+            function = "uart";
+            groups = "uart1_3_rx_tx", "uart1_3_cts_rts";
+          };
+        };
+
         uart2_pins: uart2-pins {
           mux {
             function = "uart";
Signature · 1 line
2.35.1
author maintainer
#308 lore raw

PATCH 309/1073 pinctrl: mediatek: fix the pinconf register offset of some pins

In reply to Greg Kroah-Hartman

From: Sam Shih <[email protected]>

[ Upstream commit 3476b354c65db442580ef355885c69e60c546ef0 ]

Correct the bias-pull-up, bias-pull-down and bias-disable register offset of mt7986 pin-42 to pin-49, in the original driver, the relative offset value was erroneously decremented by 1.

---
 drivers/pinctrl/mediatek/pinctrl-mt7986.c | 24 +++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
drivers/pinctrl/mediatek/pinctrl-mt7986.c +12 -12
index f26869f1a367..5cb255455a54 100644
@@ -316,10 +316,10 @@ static const struct mtk_pin_field_calc mt7986_pin_pupd_range[] = {
 	PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x30, 0x10, 9, 1),
 	PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x60, 0x10, 18, 1),
 	PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x60, 0x10, 12, 1),
-	PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x60, 0x10, 22, 1),
-	PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x60, 0x10, 20, 1),
-	PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x60, 0x10, 26, 1),
-	PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x60, 0x10, 24, 1),
+	PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x60, 0x10, 23, 1),
+	PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x60, 0x10, 21, 1),
+	PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x60, 0x10, 27, 1),
+	PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x60, 0x10, 25, 1),
 	PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x40, 0x10, 2, 1),
 	PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x40, 0x10, 1, 1),
 	PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x40, 0x10, 0, 1),
@@ -354,10 +354,10 @@ static const struct mtk_pin_field_calc mt7986_pin_r0_range[] = {
 	PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x40, 0x10, 9, 1),
 	PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x70, 0x10, 18, 1),
 	PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x70, 0x10, 12, 1),
-	PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x70, 0x10, 22, 1),
-	PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x70, 0x10, 20, 1),
-	PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x70, 0x10, 26, 1),
-	PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x70, 0x10, 24, 1),
+	PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x70, 0x10, 23, 1),
+	PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x70, 0x10, 21, 1),
+	PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x70, 0x10, 27, 1),
+	PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x70, 0x10, 25, 1),
 	PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x50, 0x10, 2, 1),
 	PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x50, 0x10, 1, 1),
 	PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x50, 0x10, 0, 1),
@@ -392,10 +392,10 @@ static const struct mtk_pin_field_calc mt7986_pin_r1_range[] = {
 	PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x50, 0x10, 9, 1),
 	PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x80, 0x10, 18, 1),
 	PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x80, 0x10, 12, 1),
-	PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x80, 0x10, 22, 1),
-	PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x80, 0x10, 20, 1),
-	PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x80, 0x10, 26, 1),
-	PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x80, 0x10, 24, 1),
+	PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x80, 0x10, 23, 1),
+	PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x80, 0x10, 21, 1),
+	PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x80, 0x10, 27, 1),
+	PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x80, 0x10, 25, 1),
 	PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x60, 0x10, 2, 1),
 	PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x60, 0x10, 1, 1),
 	PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x60, 0x10, 0, 1),
Signature · 1 line
2.35.1
author maintainer
#309 lore raw

PATCH 310/1073 wifi: iwlwifi: mei: make sure ownership confirmed message is sent

In reply to Greg Kroah-Hartman

From: Avraham Stern <[email protected]>

[ Upstream commit 5aa7ce31bd84c2f4f059200f06c537c920cbb458 ]

It is possible that CSME will try to take ownership while the driver is stopping. In this case, if the CSME takes ownership message arrives after the driver started unregistering, the iwl_mei_cache->ops is already invalid, so the host will not answer with the ownership confirmed message.
Similarly, if the take ownership message arrived after the mac was stopped or when iwl_mvm_up() failed, setting rfkill will not trigger sending the confirm message. As a result, CSME will not take ownership, which will result in a disconnection.

Fix it by sending the ownership confirmed message immediately in such cases.

---
 .../net/wireless/intel/iwlwifi/mei/iwl-mei.h  |  7 +++--
 drivers/net/wireless/intel/iwlwifi/mei/main.c | 30 ++++++++++++-------
 drivers/net/wireless/intel/iwlwifi/mvm/fw.c   |  2 ++
 drivers/net/wireless/intel/iwlwifi/mvm/mvm.h  |  4 +--
 drivers/net/wireless/intel/iwlwifi/mvm/ops.c  |  2 +-
 5 files changed, 29 insertions(+), 16 deletions(-)
drivers/net/wireless/intel/iwlwifi/mei/iwl-mei.h +4 -3
index 67122cfa2292..5409699c9a1f 100644
@@ -446,9 +446,10 @@ void iwl_mei_host_associated(const struct iwl_mei_conn_info *conn_info,
 void iwl_mei_host_disassociated(void);
 
 /**
- * iwl_mei_device_down() - must be called when the device is down
+ * iwl_mei_device_state() - must be called when the device changes up/down state
+ * @up: true if the device is up, false otherwise.
  */
-void iwl_mei_device_down(void);
+void iwl_mei_device_state(bool up);
 
 #else
 
@@ -497,7 +498,7 @@ static inline void iwl_mei_host_associated(const struct iwl_mei_conn_info *conn_
 static inline void iwl_mei_host_disassociated(void)
 {}
 
-static inline void iwl_mei_device_down(void)
+static inline void iwl_mei_device_state(bool up)
 {}
 
 #endif /* CONFIG_IWLMEI */
drivers/net/wireless/intel/iwlwifi/mei/main.c +20 -10
index 357f14626cf4..90646c54a3c5 100644
@@ -147,6 +147,8 @@ struct iwl_mei_filters {
  *	to send CSME_OWNERSHIP_CONFIRMED when the driver completes its down
  *	flow.
  * @link_prot_state: true when we are in link protection PASSIVE
+ * @device_down: true if the device is down. Used to remember to send
+ *	CSME_OWNERSHIP_CONFIRMED when the driver is already down.
  * @csa_throttle_end_wk: used when &csa_throttled is true
  * @data_q_lock: protects the access to the data queues which are
  *	accessed without the mutex.
@@ -167,6 +169,7 @@ struct iwl_mei {
 	bool csa_throttled;
 	bool csme_taking_ownership;
 	bool link_prot_state;
+	bool device_down;
 	struct delayed_work csa_throttle_end_wk;
 	spinlock_t data_q_lock;
 
@@ -798,14 +801,18 @@ static void iwl_mei_handle_csme_taking_ownership(struct mei_cl_device *cldev,
 
 	mei->got_ownership = false;
 
-	/*
-	 * Remember to send CSME_OWNERSHIP_CONFIRMED when the wifi driver
-	 * is finished taking the device down.
-	 */
-	mei->csme_taking_ownership = true;
+	if (iwl_mei_cache.ops && !mei->device_down) {
+		/*
+		 * Remember to send CSME_OWNERSHIP_CONFIRMED when the wifi
+		 * driver is finished taking the device down.
+		 */
+		mei->csme_taking_ownership = true;
 
-	if (iwl_mei_cache.ops)
-		iwl_mei_cache.ops->rfkill(iwl_mei_cache.priv, true);
+		iwl_mei_cache.ops->rfkill(iwl_mei_cache.priv, true, true);
+	} else {
+		iwl_mei_send_sap_msg(cldev,
+				     SAP_MSG_NOTIF_CSME_OWNERSHIP_CONFIRMED);
+	}
 }
 
 static void iwl_mei_handle_nvm(struct mei_cl_device *cldev,
@@ -1616,7 +1623,7 @@ void iwl_mei_set_netdev(struct net_device *netdev)
 }
 EXPORT_SYMBOL_GPL(iwl_mei_set_netdev);
 
-void iwl_mei_device_down(void)
+void iwl_mei_device_state(bool up)
 {
 	struct iwl_mei *mei;
 
@@ -1630,7 +1637,9 @@ void iwl_mei_device_down(void)
 	if (!mei)
 		goto out;
 
-	if (!mei->csme_taking_ownership)
+	mei->device_down = !up;
+
+	if (up || !mei->csme_taking_ownership)
 		goto out;
 
 	iwl_mei_send_sap_msg(mei->cldev,
@@ -1639,7 +1648,7 @@ void iwl_mei_device_down(void)
 out:
 	mutex_unlock(&iwl_mei_mutex);
 }
-EXPORT_SYMBOL_GPL(iwl_mei_device_down);
+EXPORT_SYMBOL_GPL(iwl_mei_device_state);
 
 int iwl_mei_register(void *priv, const struct iwl_mei_ops *ops)
 {
@@ -1821,6 +1830,7 @@ static int iwl_mei_probe(struct mei_cl_device *cldev,
 
 	mei_cldev_set_drvdata(cldev, mei);
 	mei->cldev = cldev;
+	mei->device_down = true;
 
 	do {
 		ret = iwl_mei_alloc_shared_mem(cldev);
drivers/net/wireless/intel/iwlwifi/mvm/fw.c +2 -0
index f041e77af059..5de34edc51fe 100644
@@ -1665,6 +1665,8 @@ int iwl_mvm_up(struct iwl_mvm *mvm)
 			iwl_rfi_send_config_cmd(mvm, NULL);
 	}
 
+	iwl_mvm_mei_device_state(mvm, true);
+
 	IWL_DEBUG_INFO(mvm, "RT uCode started.\n");
 	return 0;
  error:
drivers/net/wireless/intel/iwlwifi/mvm/mvm.h +2 -2
index bf35e130c876..cc71049bd9b3 100644
@@ -2201,10 +2201,10 @@ static inline void iwl_mvm_mei_host_disassociated(struct iwl_mvm *mvm)
 		iwl_mei_host_disassociated();
 }
 
-static inline void iwl_mvm_mei_device_down(struct iwl_mvm *mvm)
+static inline void iwl_mvm_mei_device_state(struct iwl_mvm *mvm, bool up)
 {
 	if (mvm->mei_registered)
-		iwl_mei_device_down();
+		iwl_mei_device_state(up);
 }
 
 static inline void iwl_mvm_mei_set_sw_rfkill_state(struct iwl_mvm *mvm)
drivers/net/wireless/intel/iwlwifi/mvm/ops.c +1 -1
index db43c8a83a31..3fec87fb6b7b 100644
@@ -1370,7 +1370,7 @@ void iwl_mvm_stop_device(struct iwl_mvm *mvm)
 	iwl_trans_stop_device(mvm->trans);
 	iwl_free_fw_paging(&mvm->fwrt);
 	iwl_fw_dump_conf_clear(&mvm->fwrt);
-	iwl_mvm_mei_device_down(mvm);
+	iwl_mvm_mei_device_state(mvm, false);
 }
 
 static void iwl_op_mode_mvm_stop(struct iwl_op_mode *op_mode)
Signature · 1 line
2.35.1
author maintainer
#310 lore raw

PATCH 311/1073 wifi: iwlwifi: mei: dont send SAP commands if AMT is disabled

In reply to Greg Kroah-Hartman

From: Emmanuel Grumbach <[email protected]>

[ Upstream commit 95170a46b7dddbc3ac31b20ef2e8fa9d556d783d ]

We should not send any SAP command to CSME if AMT is disabled.

---
 drivers/net/wireless/intel/iwlwifi/mei/main.c | 85 ++++++++++---------
 1 file changed, 44 insertions(+), 41 deletions(-)
drivers/net/wireless/intel/iwlwifi/mei/main.c +44 -41
index 90646c54a3c5..64a637ef199c 100644
@@ -596,8 +596,6 @@ iwl_mei_handle_rx_start_ok(struct mei_cl_device *cldev,
 			   const struct iwl_sap_me_msg_start_ok *rsp,
 			   ssize_t len)
 {
-	struct iwl_mei *mei = mei_cldev_get_drvdata(cldev);
-
 	if (len != sizeof(*rsp)) {
 		dev_err(&cldev->dev,
 			"got invalid SAP_ME_MSG_START_OK from CSME firmware\n");
@@ -616,13 +614,10 @@ iwl_mei_handle_rx_start_ok(struct mei_cl_device *cldev,
 
 	mutex_lock(&iwl_mei_mutex);
 	set_bit(IWL_MEI_STATUS_SAP_CONNECTED, &iwl_mei_status);
-	/* wifi driver has registered already */
-	if (iwl_mei_cache.ops) {
-		iwl_mei_send_sap_msg(mei->cldev,
-				     SAP_MSG_NOTIF_WIFIDR_UP);
-		iwl_mei_cache.ops->sap_connected(iwl_mei_cache.priv);
-	}
-
+	/*
+	 * We'll receive AMT_STATE SAP message in a bit and
+	 * that will continue the flow
+	 */
 	mutex_unlock(&iwl_mei_mutex);
 }
 
@@ -715,6 +710,13 @@ static void iwl_mei_set_init_conf(struct iwl_mei *mei)
 		.val = cpu_to_le32(iwl_mei_cache.rf_kill),
 	};
 
+	/* wifi driver has registered already */
+	if (iwl_mei_cache.ops) {
+		iwl_mei_send_sap_msg(mei->cldev,
+				     SAP_MSG_NOTIF_WIFIDR_UP);
+		iwl_mei_cache.ops->sap_connected(iwl_mei_cache.priv);
+	}
+
 	iwl_mei_send_sap_msg(mei->cldev, SAP_MSG_NOTIF_WHO_OWNS_NIC);
 
 	if (iwl_mei_cache.conn_info) {
@@ -1420,10 +1422,7 @@ void iwl_mei_host_associated(const struct iwl_mei_conn_info *conn_info,
 
 	mei = mei_cldev_get_drvdata(iwl_mei_global_cldev);
 
-	if (!mei)
-		goto out;
-
-	if (!mei->amt_enabled)
+	if (!mei && !mei->amt_enabled)
 		goto out;
 
 	iwl_mei_send_sap_msg_payload(mei->cldev, &msg.hdr);
@@ -1452,7 +1451,7 @@ void iwl_mei_host_disassociated(void)
 
 	mei = mei_cldev_get_drvdata(iwl_mei_global_cldev);
 
-	if (!mei)
+	if (!mei && !mei->amt_enabled)
 		goto out;
 
 	iwl_mei_send_sap_msg_payload(mei->cldev, &msg.hdr);
@@ -1488,7 +1487,7 @@ void iwl_mei_set_rfkill_state(bool hw_rfkill, bool sw_rfkill)
 
 	mei = mei_cldev_get_drvdata(iwl_mei_global_cldev);
 
-	if (!mei)
+	if (!mei && !mei->amt_enabled)
 		goto out;
 
 	iwl_mei_send_sap_msg_payload(mei->cldev, &msg.hdr);
@@ -1517,7 +1516,7 @@ void iwl_mei_set_nic_info(const u8 *mac_address, const u8 *nvm_address)
 
 	mei = mei_cldev_get_drvdata(iwl_mei_global_cldev);
 
-	if (!mei)
+	if (!mei && !mei->amt_enabled)
 		goto out;
 
 	iwl_mei_send_sap_msg_payload(mei->cldev, &msg.hdr);
@@ -1545,7 +1544,7 @@ void iwl_mei_set_country_code(u16 mcc)
 
 	mei = mei_cldev_get_drvdata(iwl_mei_global_cldev);
 
-	if (!mei)
+	if (!mei && !mei->amt_enabled)
 		goto out;
 
 	iwl_mei_send_sap_msg_payload(mei->cldev, &msg.hdr);
@@ -1571,7 +1570,7 @@ void iwl_mei_set_power_limit(const __le16 *power_limit)
 
 	mei = mei_cldev_get_drvdata(iwl_mei_global_cldev);
 
-	if (!mei)
+	if (!mei && !mei->amt_enabled)
 		goto out;
 
 	memcpy(msg.sar_chain_info_table, power_limit, sizeof(msg.sar_chain_info_table));
@@ -1678,9 +1677,10 @@ int iwl_mei_register(void *priv, const struct iwl_mei_ops *ops)
 
 		/* we have already a SAP connection */
 		if (iwl_mei_is_connected()) {
-			iwl_mei_send_sap_msg(mei->cldev,
-					     SAP_MSG_NOTIF_WIFIDR_UP);
-			ops->rfkill(priv, mei->link_prot_state);
+			if (mei->amt_enabled)
+				iwl_mei_send_sap_msg(mei->cldev,
+						     SAP_MSG_NOTIF_WIFIDR_UP);
+			ops->rfkill(priv, mei->link_prot_state, false);
 		}
 	}
 	ret = 0;
@@ -1931,29 +1931,32 @@ static void iwl_mei_remove(struct mei_cl_device *cldev)
 
 	mutex_lock(&iwl_mei_mutex);
 
-	/*
-	 * Tell CSME that we are going down so that it won't access the
-	 * memory anymore, make sure this message goes through immediately.
-	 */
-	mei->csa_throttled = false;
-	iwl_mei_send_sap_msg(mei->cldev,
-			     SAP_MSG_NOTIF_HOST_GOES_DOWN);
+	if (mei->amt_enabled) {
+		/*
+		 * Tell CSME that we are going down so that it won't access the
+		 * memory anymore, make sure this message goes through immediately.
+		 */
+		mei->csa_throttled = false;
+		iwl_mei_send_sap_msg(mei->cldev,
+				     SAP_MSG_NOTIF_HOST_GOES_DOWN);
 
-	for (i = 0; i < SEND_SAP_MAX_WAIT_ITERATION; i++) {
-		if (!iwl_mei_host_to_me_data_pending(mei))
-			break;
+		for (i = 0; i < SEND_SAP_MAX_WAIT_ITERATION; i++) {
+			if (!iwl_mei_host_to_me_data_pending(mei))
+				break;
 
-		msleep(5);
-	}
+			msleep(20);
+		}
 
-	/*
-	 * If we couldn't make sure that CSME saw the HOST_GOES_DOWN message,
-	 * it means that it will probably keep reading memory that we are going
-	 * to unmap and free, expect IOMMU error messages.
-	 */
-	if (i == SEND_SAP_MAX_WAIT_ITERATION)
-		dev_err(&mei->cldev->dev,
-			"Couldn't get ACK from CSME on HOST_GOES_DOWN message\n");
+		/*
+		 * If we couldn't make sure that CSME saw the HOST_GOES_DOWN
+		 * message, it means that it will probably keep reading memory
+		 * that we are going to unmap and free, expect IOMMU error
+		 * messages.
+		 */
+		if (i == SEND_SAP_MAX_WAIT_ITERATION)
+			dev_err(&mei->cldev->dev,
+				"Couldn't get ACK from CSME on HOST_GOES_DOWN message\n");
+	}
 
 	mutex_unlock(&iwl_mei_mutex);
 
Signature · 1 line
2.35.1
author maintainer
#311 lore raw

PATCH 312/1073 wifi: iwlwifi: mei: fix tx DHCP packet for devices with new Tx API

In reply to Greg Kroah-Hartman

From: Emmanuel Grumbach <[email protected]>

[ Upstream commit bcd68b3dbe78b7b0f7b6b55162cf1eff1e7fff9e ]

Devices with new Tx API have the IV introduced by the HW and it is not present in the skb at all. Hence we don't need to tell iwl_mvm_mei_tx_copy_to_csme to jump over 8 bytes to get to the ethernet header.

---
 drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/net/wireless/intel/iwlwifi/mvm/tx.c +7 -1
index f9e08b339e0c..6fa8d9e6b186 100644
@@ -1171,9 +1171,15 @@ static int iwl_mvm_tx_mpdu(struct iwl_mvm *mvm, struct sk_buff *skb,
 	/* From now on, we cannot access info->control */
 	iwl_mvm_skb_prepare_status(skb, dev_cmd);
 
+	/*
+	 * The IV is introduced by the HW for new tx api, and it is not present
+	 * in the skb, hence, don't tell iwl_mvm_mei_tx_copy_to_csme about the
+	 * IV for those devices.
+	 */
 	if (ieee80211_is_data(fc))
 		iwl_mvm_mei_tx_copy_to_csme(mvm, skb,
-					    info->control.hw_key ?
+					    info->control.hw_key &&
+					    !iwl_mvm_has_new_tx_api(mvm) ?
 					    info->control.hw_key->iv_len : 0);
 
 	if (iwl_trans_tx(mvm->trans, skb, dev_cmd, txq_id))
Signature · 1 line
2.35.1
author maintainer
#312 lore raw

PATCH 313/1073 wifi: iwlwifi: mei: avoid blocking sap messages handling due to rtnl lock

In reply to Greg Kroah-Hartman

From: Avraham Stern <[email protected]>

[ Upstream commit d288067ede4b375e72daf7f9a98d937ede11a311 ]

The AMT_STATE sap message handler tries to take the rtnl lock. This means that in case the rtnl lock is already taken, sap messages will not be processed.
When an interface is brought up, the host requests ownership from csme. However, since the rtnl lock is already held, if there is a pending amt state message, the host will not be able to read the ownership confirm message because the amt state message handler is pending. As a result, the host fails to get ownership although csme granted it.
Fix it by moving the part that needs the rtnl lock into a dedicated worker, so handling sap messages can continue.

---
 drivers/net/wireless/intel/iwlwifi/mei/main.c | 57 ++++++++++++-------
 1 file changed, 37 insertions(+), 20 deletions(-)
drivers/net/wireless/intel/iwlwifi/mei/main.c +37 -20
index 64a637ef199c..c0142093c768 100644
@@ -152,6 +152,8 @@ struct iwl_mei_filters {
  * @csa_throttle_end_wk: used when &csa_throttled is true
  * @data_q_lock: protects the access to the data queues which are
  *	accessed without the mutex.
+ * @netdev_work: used to defer registering and unregistering of the netdev to
+ *	avoid taking the rtnl lock in the SAP messages handlers.
  * @sap_seq_no: the sequence number for the SAP messages
  * @seq_no: the sequence number for the SAP messages
  * @dbgfs_dir: the debugfs dir entry
@@ -172,6 +174,7 @@ struct iwl_mei {
 	bool device_down;
 	struct delayed_work csa_throttle_end_wk;
 	spinlock_t data_q_lock;
+	struct work_struct netdev_work;
 
 	atomic_t sap_seq_no;
 	atomic_t seq_no;
@@ -591,6 +594,33 @@ static rx_handler_result_t iwl_mei_rx_handler(struct sk_buff **pskb)
 	return res;
 }
 
+static void iwl_mei_netdev_work(struct work_struct *wk)
+{
+	struct iwl_mei *mei =
+		container_of(wk, struct iwl_mei, netdev_work);
+	struct net_device *netdev;
+
+	/*
+	 * First take rtnl and only then the mutex to avoid an ABBA
+	 * with iwl_mei_set_netdev()
+	 */
+	rtnl_lock();
+	mutex_lock(&iwl_mei_mutex);
+
+	netdev = rcu_dereference_protected(iwl_mei_cache.netdev,
+					   lockdep_is_held(&iwl_mei_mutex));
+	if (netdev) {
+		if (mei->amt_enabled)
+			netdev_rx_handler_register(netdev, iwl_mei_rx_handler,
+						   mei);
+		else
+			netdev_rx_handler_unregister(netdev);
+	}
+
+	mutex_unlock(&iwl_mei_mutex);
+	rtnl_unlock();
+}
+
 static void
 iwl_mei_handle_rx_start_ok(struct mei_cl_device *cldev,
 			   const struct iwl_sap_me_msg_start_ok *rsp,
@@ -743,38 +773,23 @@ static void iwl_mei_handle_amt_state(struct mei_cl_device *cldev,
 				     const struct iwl_sap_msg_dw *dw)
 {
 	struct iwl_mei *mei = mei_cldev_get_drvdata(cldev);
-	struct net_device *netdev;
 
-	/*
-	 * First take rtnl and only then the mutex to avoid an ABBA
-	 * with iwl_mei_set_netdev()
-	 */
-	rtnl_lock();
 	mutex_lock(&iwl_mei_mutex);
 
-	netdev = rcu_dereference_protected(iwl_mei_cache.netdev,
-					   lockdep_is_held(&iwl_mei_mutex));
-
 	if (mei->amt_enabled == !!le32_to_cpu(dw->val))
 		goto out;
 
 	mei->amt_enabled = dw->val;
 
-	if (mei->amt_enabled) {
-		if (netdev)
-			netdev_rx_handler_register(netdev, iwl_mei_rx_handler, mei);
-
+	if (mei->amt_enabled)
 		iwl_mei_set_init_conf(mei);
-	} else {
-		if (iwl_mei_cache.ops)
-			iwl_mei_cache.ops->rfkill(iwl_mei_cache.priv, false);
-		if (netdev)
-			netdev_rx_handler_unregister(netdev);
-	}
+	else if (iwl_mei_cache.ops)
+		iwl_mei_cache.ops->rfkill(iwl_mei_cache.priv, false, false);
+
+	schedule_work(&mei->netdev_work);
 
 out:
 	mutex_unlock(&iwl_mei_mutex);
-	rtnl_unlock();
 }
 
 static void iwl_mei_handle_nic_owner(struct mei_cl_device *cldev,
@@ -1827,6 +1842,7 @@ static int iwl_mei_probe(struct mei_cl_device *cldev,
 			  iwl_mei_csa_throttle_end_wk);
 	init_waitqueue_head(&mei->get_ownership_wq);
 	spin_lock_init(&mei->data_q_lock);
+	INIT_WORK(&mei->netdev_work, iwl_mei_netdev_work);
 
 	mei_cldev_set_drvdata(cldev, mei);
 	mei->cldev = cldev;
@@ -1989,6 +2005,7 @@ static void iwl_mei_remove(struct mei_cl_device *cldev)
 	 */
 	cancel_work_sync(&mei->send_csa_msg_wk);
 	cancel_delayed_work_sync(&mei->csa_throttle_end_wk);
+	cancel_work_sync(&mei->netdev_work);
 
 	/*
 	 * If someone waits for the ownership, let him know that we are going
Signature · 1 line
2.35.1
author maintainer
#313 lore raw

PATCH 314/1073 wifi: iwlwifi: mei: fix potential NULL-ptr deref after clone

In reply to Greg Kroah-Hartman

From: Johannes Berg <[email protected]>

[ Upstream commit d3df49dda431f7ae4132a9a0ac25a5134c04e812 ]

If cloning the SKB fails, don't try to use it, but rather return as if we should pass it.

Coverity CID: 1503456

---
 drivers/net/wireless/intel/iwlwifi/mei/net.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/net/wireless/intel/iwlwifi/mei/net.c +7 -3
index 3472167c8370..eac46d1a397a 100644
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2021 Intel Corporation
+ * Copyright (C) 2021-2022 Intel Corporation
  */
 
 #include <uapi/linux/if_ether.h>
@@ -337,10 +337,14 @@ rx_handler_result_t iwl_mei_rx_filter(struct sk_buff *orig_skb,
 	if (!*pass_to_csme)
 		return RX_HANDLER_PASS;
 
-	if (ret == RX_HANDLER_PASS)
+	if (ret == RX_HANDLER_PASS) {
 		skb = skb_copy(orig_skb, GFP_ATOMIC);
-	else
+
+		if (!skb)
+			return RX_HANDLER_PASS;
+	} else {
 		skb = orig_skb;
+	}
 
 	/* CSME wants the MAC header as well, push it back */
 	skb_push(skb, skb->data - skb_mac_header(skb));
Signature · 1 line
2.35.1
author maintainer
#314 lore raw

PATCH 315/1073 module: Fix NULL vs IS_ERR checking for module_get_next_page

In reply to Greg Kroah-Hartman

From: Miaoqian Lin <[email protected]>

[ Upstream commit 45af1d7aae7d5520d2858f8517a1342646f015db ]

The module_get_next_page() function return error pointers on error instead of NULL.
Use IS_ERR() to check the return value to fix this.

Fixes b1ae6dc41eaa ("module: add in-kernel support for decompressing")
---
 kernel/module/decompress.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
kernel/module/decompress.c +4 -4
index 4d0bcb3d9e44..82c07b1d9797 100644
@@ -114,8 +114,8 @@ static ssize_t module_gzip_decompress(struct load_info *info,
 	do {
 		struct page *page = module_get_next_page(info);
 
-		if (!page) {
-			retval = -ENOMEM;
+		if (IS_ERR(page)) {
+			retval = PTR_ERR(page);
 			goto out_inflate_end;
 		}
 
@@ -173,8 +173,8 @@ static ssize_t module_xz_decompress(struct load_info *info,
 	do {
 		struct page *page = module_get_next_page(info);
 
-		if (!page) {
-			retval = -ENOMEM;
+		if (IS_ERR(page)) {
+			retval = PTR_ERR(page);
 			goto out;
 		}
 
Signature · 1 line
2.35.1
author maintainer
#315 lore raw

PATCH 316/1073 ASoC: codecs: wsa883x: Use proper shutdown GPIO polarity

In reply to Greg Kroah-Hartman

From: Krzysztof Kozlowski <[email protected]>

[ Upstream commit ec5dba73f7ba10797904cf18092d2e6975a22147 ]

The shutdown GPIO is active low (SD_N), but this depends on actual board layout. Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.

Invert the GPIO to match logical value.

---
 sound/soc/codecs/wsa883x.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
sound/soc/codecs/wsa883x.c +2 -2
index 63e1d7aa6137..cb1d0a3e90e6 100644
@@ -1393,7 +1393,7 @@ static int wsa883x_probe(struct sdw_slave *pdev,
 	}
 
 	wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown",
-						GPIOD_FLAGS_BIT_NONEXCLUSIVE);
+						GPIOD_FLAGS_BIT_NONEXCLUSIVE | GPIOD_OUT_HIGH);
 	if (IS_ERR(wsa883x->sd_n)) {
 		dev_err(&pdev->dev, "Shutdown Control GPIO not found\n");
 		ret = PTR_ERR(wsa883x->sd_n);
@@ -1411,7 +1411,7 @@ static int wsa883x_probe(struct sdw_slave *pdev,
 	pdev->prop.sink_ports = GENMASK(WSA883X_MAX_SWR_PORTS, 0);
 	pdev->prop.sink_dpn_prop = wsa_sink_dpn_prop;
 	pdev->prop.scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY;
-	gpiod_direction_output(wsa883x->sd_n, 1);
+	gpiod_direction_output(wsa883x->sd_n, 0);
 
 	wsa883x->regmap = devm_regmap_init_sdw(pdev, &wsa883x_regmap_config);
 	if (IS_ERR(wsa883x->regmap)) {
Signature · 1 line
2.35.1
author maintainer
#316 lore raw

PATCH 317/1073 ASoC: codecs: wsa883x: use correct header file

In reply to Greg Kroah-Hartman

From: Randy Dunlap <[email protected]>

[ Upstream commit 5f52ceddc40cd61b1dd2ecf735624deaf05f779f ]

Fix build errors when GPIOLIB is not set/enabled:

../sound/soc/codecs/wsa883x.c: In function 'wsa883x_probe':
../sound/soc/codecs/wsa883x.c:1394:25: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_regulator_get_optional'? [-Werror=implicit-function-declaration]

         wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown",
../sound/soc/codecs/wsa883x.c:1395:49: error: 'GPIOD_FLAGS_BIT_NONEXCLUSIVE' undeclared (first use in this function)
         GPIOD_FLAGS_BIT_NONEXCLUSIVE);
../sound/soc/codecs/wsa883x.c:1414:9: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
         gpiod_direction_output(wsa883x->sd_n, 1);
Fixes 43b8c7dc85a1 ("ASoC: codecs: add wsa883x amplifier support")
Cc Srinivas Kandagatla <[email protected]>
Cc Banajit Goswami <[email protected]>
Cc Mark Brown <[email protected]>
Cc Liam Girdwood <[email protected]>
Cc Jaroslav Kysela <[email protected]>
Cc Takashi Iwai <[email protected]>
---
 sound/soc/codecs/wsa883x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/wsa883x.c +1 -1
index cb1d0a3e90e6..9dfa0ac08e6f 100644
@@ -7,7 +7,7 @@
 #include <linux/debugfs.h>
 #include <linux/delay.h>
 #include <linux/device.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
Signature · 1 line
2.35.1
author maintainer
#317 lore raw

PATCH 318/1073 selftests/bpf: Fix xdp_synproxy compilation failure in 32-bit arch

In reply to Greg Kroah-Hartman

From: Yang Jihong <[email protected]>

[ Upstream commit e4c9cf0ce8c413c2030e8fb215551d7e0582ee7b ]

xdp_synproxy fails to be compiled in the 32-bit arch, log is as follows:

xdp_synproxy.c: In function 'parse_options':
xdp_synproxy.c:175:36: error: left shift count >= width of type [-Werror=shift-count-overflow]

    175 |                 *tcpipopts = (mss6 << 32) | (ttl << 24) | (wscale << 16) | mss4;
        |                                    ^~
  xdp_synproxy.c: In function 'syncookie_open_bpf_maps':
  xdp_synproxy.c:289:28: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
    289 |                 .map_ids = (__u64)map_ids,
        |                            ^

Fix it.

Fixes fb5cd0ce70d4 ("selftests/bpf: Add selftests for raw syncookie helpers")
---
 tools/testing/selftests/bpf/xdp_synproxy.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
tools/testing/selftests/bpf/xdp_synproxy.c +3 -2
index d874ddfb39c4..8432836f3be2 100644
@@ -104,7 +104,8 @@ static void parse_options(int argc, char *argv[], unsigned int *ifindex, __u32 *
 		{ "tc", no_argument, NULL, 'c' },
 		{ NULL, 0, NULL, 0 },
 	};
-	unsigned long mss4, mss6, wscale, ttl;
+	unsigned long mss4, wscale, ttl;
+	unsigned long long mss6;
 	unsigned int tcpipopts_mask = 0;
 
 	if (argc < 2)
@@ -286,7 +287,7 @@ static int syncookie_open_bpf_maps(__u32 prog_id, int *values_map_fd, int *ports
 
 	prog_info = (struct bpf_prog_info) {
 		.nr_map_ids = 8,
-		.map_ids = (__u64)map_ids,
+		.map_ids = (__u64)(unsigned long)map_ids,
 	};
 	info_len = sizeof(prog_info);
 
Signature · 1 line
2.35.1
author maintainer
#318 lore raw

PATCH 319/1073 drm/mediatek: Modify dpi power on/off sequence.

In reply to Greg Kroah-Hartman

From: Xinlei Lee <[email protected]>

[ Upstream commit ff446c0f6290185cefafe3b376bb86063a3a9f6a ]

Modify dpi power on/off sequence so that the first gpio operation will take effect.

Fixes 6bd4763fd532 ("drm/mediatek: set dpi pin mode to gpio low to avoid leakage current")
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/gpu/drm/mediatek/mtk_dpi.c +6 -6
index 630a4e301ef6..b11b5a2c0663 100644
@@ -462,9 +462,6 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
 	if (--dpi->refcount != 0)
 		return;
 
-	if (dpi->pinctrl && dpi->pins_gpio)
-		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
-
 	mtk_dpi_disable(dpi);
 	clk_disable_unprepare(dpi->pixel_clk);
 	clk_disable_unprepare(dpi->engine_clk);
@@ -489,9 +486,6 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
 		goto err_pixel;
 	}
 
-	if (dpi->pinctrl && dpi->pins_dpi)
-		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
-
 	return 0;
 
 err_pixel:
@@ -722,12 +716,18 @@ static void mtk_dpi_bridge_disable(struct drm_bridge *bridge)
 	struct mtk_dpi *dpi = bridge_to_dpi(bridge);
 
 	mtk_dpi_power_off(dpi);
+
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
 }
 
 static void mtk_dpi_bridge_enable(struct drm_bridge *bridge)
 {
 	struct mtk_dpi *dpi = bridge_to_dpi(bridge);
 
+	if (dpi->pinctrl && dpi->pins_dpi)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
+
 	mtk_dpi_power_on(dpi);
 	mtk_dpi_set_display_mode(dpi, &dpi->mode);
 	mtk_dpi_enable(dpi);
Signature · 1 line
2.35.1
author maintainer
#319 lore raw

PATCH 320/1073 ASoC: pxa: fix null-pointer dereference in filter()

In reply to Greg Kroah-Hartman

From: Zeng Heng <[email protected]>

[ Upstream commit ec7bf231aaa1bdbcb69d23bc50c753c80fb22429 ]

kasprintf() would return NULL pointer when kmalloc() fail to allocate. Need to check the return pointer before calling strcmp().

Fixes 7a824e214e25 ("ASoC: mmp: add audio dma support")
---
 sound/soc/pxa/mmp-pcm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/pxa/mmp-pcm.c +1 -1
index 5d520e18e512..99b245e3079a 100644
@@ -98,7 +98,7 @@ static bool filter(struct dma_chan *chan, void *param)
 
 	devname = kasprintf(GFP_KERNEL, "%s.%d", dma_data->dma_res->name,
 		dma_data->ssp_id);
-	if ((strcmp(dev_name(chan->device->dev), devname) == 0) &&
+	if (devname && (strcmp(dev_name(chan->device->dev), devname) == 0) &&
 		(chan->chan_id == dma_data->dma_res->start)) {
 		found = true;
 	}
Signature · 1 line
2.35.1
author maintainer
#320 lore raw

PATCH 321/1073 nvmet: only allocate a single slab for bvecs

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

[ Upstream commit fa8f9ac42350edd3ce82d0d148a60f0fa088f995 ]

There is no need to have a separate slab cache for each namespace, and having separate ones creates duplicate debugs file names as well.

---
 drivers/nvme/target/core.c        | 22 ++++++++++++++--------
 drivers/nvme/target/io-cmd-file.c | 16 +++-------------
 drivers/nvme/target/nvmet.h       |  3 ++-
 3 files changed, 19 insertions(+), 22 deletions(-)
drivers/nvme/target/core.c +14 -8
index aecb5853f8da..683b75a992b3 100644
@@ -15,6 +15,7 @@
 
 #include "nvmet.h"
 
+struct kmem_cache *nvmet_bvec_cache;
 struct workqueue_struct *buffered_io_wq;
 struct workqueue_struct *zbd_wq;
 static const struct nvmet_fabrics_ops *nvmet_transports[NVMF_TRTYPE_MAX];
@@ -1631,26 +1632,28 @@ void nvmet_subsys_put(struct nvmet_subsys *subsys)
 
 static int __init nvmet_init(void)
 {
-	int error;
+	int error = -ENOMEM;
 
 	nvmet_ana_group_enabled[NVMET_DEFAULT_ANA_GRPID] = 1;
 
+	nvmet_bvec_cache = kmem_cache_create("nvmet-bvec",
+			NVMET_MAX_MPOOL_BVEC * sizeof(struct bio_vec), 0,
+			SLAB_HWCACHE_ALIGN, NULL);
+	if (!nvmet_bvec_cache)
+		return -ENOMEM;
+
 	zbd_wq = alloc_workqueue("nvmet-zbd-wq", WQ_MEM_RECLAIM, 0);
 	if (!zbd_wq)
-		return -ENOMEM;
+		goto out_destroy_bvec_cache;
 
 	buffered_io_wq = alloc_workqueue("nvmet-buffered-io-wq",
 			WQ_MEM_RECLAIM, 0);
-	if (!buffered_io_wq) {
-		error = -ENOMEM;
+	if (!buffered_io_wq)
 		goto out_free_zbd_work_queue;
-	}
 
 	nvmet_wq = alloc_workqueue("nvmet-wq", WQ_MEM_RECLAIM, 0);
-	if (!nvmet_wq) {
-		error = -ENOMEM;
+	if (!nvmet_wq)
 		goto out_free_buffered_work_queue;
-	}
 
 	error = nvmet_init_discovery();
 	if (error)
@@ -1669,6 +1672,8 @@ static int __init nvmet_init(void)
 	destroy_workqueue(buffered_io_wq);
 out_free_zbd_work_queue:
 	destroy_workqueue(zbd_wq);
+out_destroy_bvec_cache:
+	kmem_cache_destroy(nvmet_bvec_cache);
 	return error;
 }
 
@@ -1680,6 +1685,7 @@ static void __exit nvmet_exit(void)
 	destroy_workqueue(nvmet_wq);
 	destroy_workqueue(buffered_io_wq);
 	destroy_workqueue(zbd_wq);
+	kmem_cache_destroy(nvmet_bvec_cache);
 
 	BUILD_BUG_ON(sizeof(struct nvmf_disc_rsp_page_entry) != 1024);
 	BUILD_BUG_ON(sizeof(struct nvmf_disc_rsp_page_hdr) != 1024);
drivers/nvme/target/io-cmd-file.c +3 -13
index 64b47e2a4633..e55ec6fefd7f 100644
@@ -11,7 +11,6 @@
 #include <linux/fs.h>
 #include "nvmet.h"
 
-#define NVMET_MAX_MPOOL_BVEC		16
 #define NVMET_MIN_MPOOL_OBJ		16
 
 void nvmet_file_ns_revalidate(struct nvmet_ns *ns)
@@ -26,8 +25,6 @@ void nvmet_file_ns_disable(struct nvmet_ns *ns)
 			flush_workqueue(buffered_io_wq);
 		mempool_destroy(ns->bvec_pool);
 		ns->bvec_pool = NULL;
-		kmem_cache_destroy(ns->bvec_cache);
-		ns->bvec_cache = NULL;
 		fput(ns->file);
 		ns->file = NULL;
 	}
@@ -59,16 +56,8 @@ int nvmet_file_ns_enable(struct nvmet_ns *ns)
 	ns->blksize_shift = min_t(u8,
 			file_inode(ns->file)->i_blkbits, 12);
 
-	ns->bvec_cache = kmem_cache_create("nvmet-bvec",
-			NVMET_MAX_MPOOL_BVEC * sizeof(struct bio_vec),
-			0, SLAB_HWCACHE_ALIGN, NULL);
-	if (!ns->bvec_cache) {
-		ret = -ENOMEM;
-		goto err;
-	}
-
 	ns->bvec_pool = mempool_create(NVMET_MIN_MPOOL_OBJ, mempool_alloc_slab,
-			mempool_free_slab, ns->bvec_cache);
+			mempool_free_slab, nvmet_bvec_cache);
 
 	if (!ns->bvec_pool) {
 		ret = -ENOMEM;
@@ -77,9 +66,10 @@ int nvmet_file_ns_enable(struct nvmet_ns *ns)
 
 	return ret;
 err:
+	fput(ns->file);
+	ns->file = NULL;
 	ns->size = 0;
 	ns->blksize_shift = 0;
-	nvmet_file_ns_disable(ns);
 	return ret;
 }
 
drivers/nvme/target/nvmet.h +2 -1
index dfe3894205aa..bda1c1f71f39 100644
@@ -77,7 +77,6 @@ struct nvmet_ns {
 
 	struct completion	disable_done;
 	mempool_t		*bvec_pool;
-	struct kmem_cache	*bvec_cache;
 
 	int			use_p2pmem;
 	struct pci_dev		*p2p_dev;
@@ -393,6 +392,8 @@ struct nvmet_req {
 	u64			error_slba;
 };
 
+#define NVMET_MAX_MPOOL_BVEC		16
+extern struct kmem_cache *nvmet_bvec_cache;
 extern struct workqueue_struct *buffered_io_wq;
 extern struct workqueue_struct *zbd_wq;
 extern struct workqueue_struct *nvmet_wq;
Signature · 1 line
2.35.1
author maintainer
#321 lore raw

PATCH 322/1073 regulator: core: fix unbalanced of node refcount in regulator_dev_lookup()

In reply to Greg Kroah-Hartman

From: Yang Yingliang <[email protected]>

[ Upstream commit f2b41b748c19962b82709d9f23c6b2b0ce9d2f91 ]

I got the the following report:

OF: ERROR: memory leak, expected refcount 1 instead of 2, of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@62/regulators/exten

In of_get_regulator(), the node is returned from of_parse_phandle() with refcount incremented, after using it, of_node_put() need be called.

Fixes 69511a452e6d ("regulator: map consumer regulator based on device tree")
---
 drivers/regulator/core.c | 1 +
 1 file changed, 1 insertion(+)
drivers/regulator/core.c +1 -0
index c0f368f1b49f..afd17b13de7c 100644
@@ -1925,6 +1925,7 @@ static struct regulator_dev *regulator_dev_lookup(struct device *dev,
 		node = of_get_regulator(dev, supply);
 		if (node) {
 			r = of_find_regulator_by_node(node);
+			of_node_put(node);
 			if (r)
 				return r;
 
Signature · 1 line
2.35.1
author maintainer
#322 lore raw

PATCH 323/1073 amdgpu/pm: prevent array underflow in vega20_odn_edit_dpm_table()

In reply to Greg Kroah-Hartman

From: Dan Carpenter <[email protected]>

[ Upstream commit d27252b5706e51188aed7647126e44dcf9e940c1 ]

In the PP_OD_EDIT_VDDC_CURVE case the "input_index" variable is capped at 2 but not checked for negative values so it results in an out of bounds read. This value comes from the user via sysfs.

Fixes d5bf26539494 ("drm/amd/powerplay: added vega20 overdrive support V3")
---
 drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega20_hwmgr.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega20_hwmgr.c +2 -1
index 97b3ad369046..b30684c84e20 100644
@@ -2961,7 +2961,8 @@ static int vega20_odn_edit_dpm_table(struct pp_hwmgr *hwmgr,
 			data->od8_settings.od8_settings_array;
 	OverDriveTable_t *od_table =
 			&(data->smc_state_table.overdrive_table);
-	int32_t input_index, input_clk, input_vol, i;
+	int32_t input_clk, input_vol, i;
+	uint32_t input_index;
 	int od8_id;
 	int ret;
 
Signature · 1 line
2.35.1
author maintainer
#323 lore raw

PATCH 324/1073 nvme: return err on nvme_init_non_mdts_limits fail

In reply to Greg Kroah-Hartman

From: Joel Granados <[email protected]>

[ Upstream commit bcaf434b8f04e1ee82a8b1e1bce0de99fbff67fa ]

In nvme_init_non_mdts_limits function we were returning 0 when kzalloc failed; it now returns -ENOMEM.

Fixes 5befc7c26e5a ("nvme: implement non-mdts command limits")
---
 drivers/nvme/host/core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/nvme/host/core.c +1 -1
index aca50bb93750..cd2e2bfeae82 100644
@@ -3043,7 +3043,7 @@ static int nvme_init_non_mdts_limits(struct nvme_ctrl *ctrl)
 
 	id = kzalloc(sizeof(*id), GFP_KERNEL);
 	if (!id)
-		return 0;
+		return -ENOMEM;
 
 	c.identify.opcode = nvme_admin_identify;
 	c.identify.cns = NVME_ID_CNS_CS_CTRL;
Signature · 1 line
2.35.1
author maintainer
#324 lore raw

PATCH 325/1073 wifi: rtw89: Fix some error handling path in rtw89_core_sta_assoc()

In reply to Greg Kroah-Hartman

From: Christophe JAILLET <[email protected]>

[ Upstream commit 81c0b8928437ddfe87b0024c5bd817bc331d8524 ]

'ret' is not updated after a function call in rtw89_core_sta_assoc(). This prevent error handling from working.

Add the missing assignment.

---
 drivers/net/wireless/realtek/rtw89/core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/realtek/rtw89/core.c +1 -1
index 8b338e5ce364..732015228bd3 100644
@@ -2500,7 +2500,7 @@ int rtw89_core_sta_assoc(struct rtw89_dev *rtwdev,
 	}
 
 	/* update cam aid mac_id net_type */
-	rtw89_fw_h2c_cam(rtwdev, rtwvif, rtwsta, NULL);
+	ret = rtw89_fw_h2c_cam(rtwdev, rtwvif, rtwsta, NULL);
 	if (ret) {
 		rtw89_warn(rtwdev, "failed to send h2c cam\n");
 		return ret;
Signature · 1 line
2.35.1
author maintainer
#325 lore raw

PATCH 326/1073 regulator: qcom-rpmh: Fix PMR735a S3 regulator spec

In reply to Greg Kroah-Hartman

From: Konrad Dybcio <[email protected]>

[ Upstream commit dd801b2265c81bf0c8b0b4b8f7c1e7bfed078403 ]

PMR735a has a wider range than previously defined. Fix it.

Fixes c4e5aa3dbee5 ("regulator: qcom-rpmh: Add PM7325/PMR735A regulator support")
---
 drivers/regulator/qcom-rpmh-regulator.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/regulator/qcom-rpmh-regulator.c +1 -1
index 561de6b2e6e3..5839e4732336 100644
@@ -1188,7 +1188,7 @@ static const struct rpmh_vreg_init_data pm7325_vreg_data[] = {
 static const struct rpmh_vreg_init_data pmr735a_vreg_data[] = {
 	RPMH_VREG("smps1",  "smp%s1",  &pmic5_ftsmps520, "vdd-s1"),
 	RPMH_VREG("smps2",  "smp%s2",  &pmic5_ftsmps520, "vdd-s2"),
-	RPMH_VREG("smps3",  "smp%s3",  &pmic5_hfsmps510, "vdd-s3"),
+	RPMH_VREG("smps3",  "smp%s3",  &pmic5_hfsmps515, "vdd-s3"),
 	RPMH_VREG("ldo1",   "ldo%s1",  &pmic5_nldo,      "vdd-l1-l2"),
 	RPMH_VREG("ldo2",   "ldo%s2",  &pmic5_nldo,      "vdd-l1-l2"),
 	RPMH_VREG("ldo3",   "ldo%s3",  &pmic5_nldo,      "vdd-l3"),
Signature · 1 line
2.35.1
author maintainer
#326 lore raw

PATCH 327/1073 drm/fourcc: Fix vsub/hsub for Q410 and Q401

In reply to Greg Kroah-Hartman

From: Brian Starkey <[email protected]>

[ Upstream commit b230555f3257f197dd98641ef6ebaf778b52dd51 ]

These formats are not subsampled, but that means hsub and vsub should be 1, not 0.

---
 drivers/gpu/drm/drm_fourcc.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/drm_fourcc.c +4 -4
index 07741b678798..6768b7d18b6f 100644
@@ -263,12 +263,12 @@ const struct drm_format_info *__drm_format_info(u32 format)
 		  .vsub = 2, .is_yuv = true },
 		{ .format = DRM_FORMAT_Q410,		.depth = 0,
 		  .num_planes = 3, .char_per_block = { 2, 2, 2 },
-		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 0,
-		  .vsub = 0, .is_yuv = true },
+		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 1,
+		  .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_Q401,		.depth = 0,
 		  .num_planes = 3, .char_per_block = { 2, 2, 2 },
-		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 0,
-		  .vsub = 0, .is_yuv = true },
+		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 1,
+		  .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_P030,            .depth = 0,  .num_planes = 2,
 		  .char_per_block = { 4, 8, 0 }, .block_w = { 3, 3, 0 }, .block_h = { 1, 1, 0 },
 		  .hsub = 2, .vsub = 2, .is_yuv = true},
Signature · 1 line
2.35.1
author maintainer
#327 lore raw

PATCH 328/1073 integrity: Fix memory leakage in keyring allocation error path

In reply to Greg Kroah-Hartman

From: GUO Zihua <[email protected]>

[ Upstream commit 39419ef7af0916cc3620ecf1ed42d29659109bf3 ]

Key restriction is allocated in integrity_init_keyring(). However, if keyring allocation failed, it is not freed, causing memory leaks.

Fixes 2b6aa412ff23 ("KEYS: Use structure to capture key restriction function and data")
---
 security/integrity/digsig.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
security/integrity/digsig.c +5 -1
index 8a82a6c7f48a..f2193c531f4a 100644
@@ -126,6 +126,7 @@ int __init integrity_init_keyring(const unsigned int id)
 {
 	struct key_restriction *restriction;
 	key_perm_t perm;
+	int ret;
 
 	perm = (KEY_POS_ALL & ~KEY_POS_SETATTR) | KEY_USR_VIEW
 		| KEY_USR_READ | KEY_USR_SEARCH;
@@ -154,7 +155,10 @@ int __init integrity_init_keyring(const unsigned int id)
 		perm |= KEY_USR_WRITE;
 
 out:
-	return __integrity_init_keyring(id, perm, restriction);
+	ret = __integrity_init_keyring(id, perm, restriction);
+	if (ret)
+		kfree(restriction);
+	return ret;
 }
 
 static int __init integrity_add_key(const unsigned int id, const void *data,
Signature · 1 line
2.35.1
author maintainer
#328 lore raw

PATCH 329/1073 ima: Fix misuse of dereference of pointer in template_desc_init_fields()

In reply to Greg Kroah-Hartman

From: Xiu Jianfeng <[email protected]>

[ Upstream commit 25369175ce84813dd99d6604e710dc2491f68523 ]

The input parameter @fields is type of struct ima_template_field ***, so when allocates array memory for @fields, the size of element should be sizeof(**field) instead of sizeof(*field).

Actually the original code would not cause any runtime error, but it's better to make it logically right.

Fixes adf53a778a0a ("ima: new templates management mechanism")
---
 security/integrity/ima/ima_template.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
security/integrity/ima/ima_template.c +2 -2
index c25079faa208..195ac18f0927 100644
@@ -245,11 +245,11 @@ int template_desc_init_fields(const char *template_fmt,
 	}
 
 	if (fields && num_fields) {
-		*fields = kmalloc_array(i, sizeof(*fields), GFP_KERNEL);
+		*fields = kmalloc_array(i, sizeof(**fields), GFP_KERNEL);
 		if (*fields == NULL)
 			return -ENOMEM;
 
-		memcpy(*fields, found_fields, i * sizeof(*fields));
+		memcpy(*fields, found_fields, i * sizeof(**fields));
 		*num_fields = i;
 	}
 
Signature · 1 line
2.35.1
author maintainer
#329 lore raw

PATCH 330/1073 block: clear ->slave_dir when dropping the main slave_dir reference

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

[ Upstream commit d90db3b1c8676bc88b4309c5a571333de2263b8e ]

Zero out the pointer to ->slave_dir so that the holder code doesn't incorrectly treat the object as alive when add_disk failed or after del_gendisk was called.

---
 block/genhd.c | 2 ++
 1 file changed, 2 insertions(+)
block/genhd.c +2 -0
index 044ff97381e3..28654723bc2b 100644
@@ -522,6 +522,7 @@ int __must_check device_add_disk(struct device *parent, struct gendisk *disk,
 	rq_qos_exit(disk->queue);
 out_put_slave_dir:
 	kobject_put(disk->slave_dir);
+	disk->slave_dir = NULL;
 out_put_holder_dir:
 	kobject_put(disk->part0->bd_holder_dir);
 out_del_integrity:
@@ -618,6 +619,7 @@ void del_gendisk(struct gendisk *disk)
 
 	kobject_put(disk->part0->bd_holder_dir);
 	kobject_put(disk->slave_dir);
+	disk->slave_dir = NULL;
 
 	part_stat_set_all(disk->part0, 0);
 	disk->part0->bd_stamp = 0;
Signature · 1 line
2.35.1
author maintainer
#330 lore raw

PATCH 331/1073 dm: cleanup open_table_device

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

[ Upstream commit b9a785d2dc6567b2fd9fc60057a6a945a276927a ]

Move all the logic for allocation the table_device and linking it into the list into the open_table_device. This keeps the code tidy and ensures that the table_devices only exist in fully initialized state.

Stable-dep-of: 1a581b721699 ("dm: track per-add_disk holder relations in DM")

---
 drivers/md/dm.c | 56 ++++++++++++++++++++++++-------------------------
 1 file changed, 27 insertions(+), 29 deletions(-)
drivers/md/dm.c +27 -29
index b4a2cb5333fc..1903afa4618a 100644
@@ -732,28 +732,41 @@ static char *_dm_claim_ptr = "I belong to device-mapper";
 /*
  * Open a table device so we can use it as a map destination.
  */
-static int open_table_device(struct table_device *td, dev_t dev,
-			     struct mapped_device *md)
+static struct table_device *open_table_device(struct mapped_device *md,
+		dev_t dev, fmode_t mode)
 {
+	struct table_device *td;
 	struct block_device *bdev;
 	u64 part_off;
 	int r;
 
-	BUG_ON(td->dm_dev.bdev);
+	td = kmalloc_node(sizeof(*td), GFP_KERNEL, md->numa_node_id);
+	if (!td)
+		return ERR_PTR(-ENOMEM);
+	refcount_set(&td->count, 1);
 
-	bdev = blkdev_get_by_dev(dev, td->dm_dev.mode | FMODE_EXCL, _dm_claim_ptr);
-	if (IS_ERR(bdev))
-		return PTR_ERR(bdev);
+	bdev = blkdev_get_by_dev(dev, mode | FMODE_EXCL, _dm_claim_ptr);
+	if (IS_ERR(bdev)) {
+		r = PTR_ERR(bdev);
+		goto out_free_td;
+	}
 
 	r = bd_link_disk_holder(bdev, dm_disk(md));
-	if (r) {
-		blkdev_put(bdev, td->dm_dev.mode | FMODE_EXCL);
-		return r;
-	}
+	if (r)
+		goto out_blkdev_put;
 
+	td->dm_dev.mode = mode;
 	td->dm_dev.bdev = bdev;
 	td->dm_dev.dax_dev = fs_dax_get_by_bdev(bdev, &part_off, NULL, NULL);
-	return 0;
+	format_dev_t(td->dm_dev.name, dev);
+	list_add(&td->list, &md->table_devices);
+	return td;
+
+out_blkdev_put:
+	blkdev_put(bdev, mode | FMODE_EXCL);
+out_free_td:
+	kfree(td);
+	return ERR_PTR(r);
 }
 
 /*
@@ -786,31 +799,16 @@ static struct table_device *find_table_device(struct list_head *l, dev_t dev,
 int dm_get_table_device(struct mapped_device *md, dev_t dev, fmode_t mode,
 			struct dm_dev **result)
 {
-	int r;
 	struct table_device *td;
 
 	mutex_lock(&md->table_devices_lock);
 	td = find_table_device(&md->table_devices, dev, mode);
 	if (!td) {
-		td = kmalloc_node(sizeof(*td), GFP_KERNEL, md->numa_node_id);
-		if (!td) {
-			mutex_unlock(&md->table_devices_lock);
-			return -ENOMEM;
-		}
-
-		td->dm_dev.mode = mode;
-		td->dm_dev.bdev = NULL;
-
-		if ((r = open_table_device(td, dev, md))) {
+		td = open_table_device(md, dev, mode);
+		if (IS_ERR(td)) {
 			mutex_unlock(&md->table_devices_lock);
-			kfree(td);
-			return r;
+			return PTR_ERR(td);
 		}
-
-		format_dev_t(td->dm_dev.name, dev);
-
-		refcount_set(&td->count, 1);
-		list_add(&td->list, &md->table_devices);
 	} else {
 		refcount_inc(&td->count);
 	}
Signature · 1 line
2.35.1
author maintainer
#331 lore raw

PATCH 332/1073 dm: cleanup close_table_device

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

[ Upstream commit 7b5865831c1003122f737df5e16adaa583f1a595 ]

Take the list unlink and free into close_table_device so that no half torn down table_devices exist. Also remove the check for a NULL bdev as that can't happen - open_table_device never adds a table_device to the list that does not have a valid block_device.

Stable-dep-of: 1a581b721699 ("dm: track per-add_disk holder relations in DM")

---
 drivers/md/dm.c | 12 +++---------
 1 file changed, 3 insertions(+), 9 deletions(-)
drivers/md/dm.c +3 -9
index 1903afa4618a..620abcef2df5 100644
@@ -774,14 +774,11 @@ static struct table_device *open_table_device(struct mapped_device *md,
  */
 static void close_table_device(struct table_device *td, struct mapped_device *md)
 {
-	if (!td->dm_dev.bdev)
-		return;
-
 	bd_unlink_disk_holder(td->dm_dev.bdev, dm_disk(md));
 	blkdev_put(td->dm_dev.bdev, td->dm_dev.mode | FMODE_EXCL);
 	put_dax(td->dm_dev.dax_dev);
-	td->dm_dev.bdev = NULL;
-	td->dm_dev.dax_dev = NULL;
+	list_del(&td->list);
+	kfree(td);
 }
 
 static struct table_device *find_table_device(struct list_head *l, dev_t dev,
@@ -823,11 +820,8 @@ void dm_put_table_device(struct mapped_device *md, struct dm_dev *d)
 	struct table_device *td = container_of(d, struct table_device, dm_dev);
 
 	mutex_lock(&md->table_devices_lock);
-	if (refcount_dec_and_test(&td->count)) {
+	if (refcount_dec_and_test(&td->count))
 		close_table_device(td, md);
-		list_del(&td->list);
-		kfree(td);
-	}
 	mutex_unlock(&md->table_devices_lock);
 }
 
Signature · 1 line
2.35.1
author maintainer
#332 lore raw

PATCH 333/1073 dm: make sure create and remove dm device wont race with open and close table

In reply to Greg Kroah-Hartman

From: Yu Kuai <[email protected]>

[ Upstream commit d563792c8933a810d28ce0f2831f0726c2b15a31 ]

open_table_device() and close_table_device() is protected by table_devices_lock, hence use it to protect add_disk() and del_gendisk().

Prepare to track per-add_disk holder relations in dm.

Stable-dep-of: 1a581b721699 ("dm: track per-add_disk holder relations in DM")

---
 drivers/md/dm.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/md/dm.c +16 -0
index 620abcef2df5..e7fc2a69633c 100644
@@ -1965,7 +1965,14 @@ static void cleanup_mapped_device(struct mapped_device *md)
 		spin_unlock(&_minor_lock);
 		if (dm_get_md_type(md) != DM_TYPE_NONE) {
 			dm_sysfs_exit(md);
+
+			/*
+			 * Hold lock to make sure del_gendisk() won't concurrent
+			 * with open/close_table_device().
+			 */
+			mutex_lock(&md->table_devices_lock);
 			del_gendisk(md->disk);
+			mutex_unlock(&md->table_devices_lock);
 		}
 		dm_queue_destroy_crypto_profile(md->queue);
 		put_disk(md->disk);
@@ -2325,15 +2332,24 @@ int dm_setup_md_queue(struct mapped_device *md, struct dm_table *t)
 	if (r)
 		return r;
 
+	/*
+	 * Hold lock to make sure add_disk() and del_gendisk() won't concurrent
+	 * with open_table_device() and close_table_device().
+	 */
+	mutex_lock(&md->table_devices_lock);
 	r = add_disk(md->disk);
+	mutex_unlock(&md->table_devices_lock);
 	if (r)
 		return r;
 
 	r = dm_sysfs_init(md);
 	if (r) {
+		mutex_lock(&md->table_devices_lock);
 		del_gendisk(md->disk);
+		mutex_unlock(&md->table_devices_lock);
 		return r;
 	}
+
 	md->type = type;
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#333 lore raw

PATCH 334/1073 dm: track per-add_disk holder relations in DM

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

[ Upstream commit 1a581b72169968f4154b5793828f3bc28b258b35 ]

dm is a bit special in that it opens the underlying devices. Commit 89f871af1b26 ("dm: delay registering the gendisk") tried to accommodate that by allowing to add the holder to the list before add_gendisk and then just add them to sysfs once add_disk is called. But that leads to really odd lifetime problems and error handling problems as we can't know the state of the kobjects and don't unwind properly. To fix this switch to just registering all existing table_devices with the holder code right after add_disk, and remove them before calling del_gendisk.

---
 drivers/md/dm.c | 49 +++++++++++++++++++++++++++++++++++++++----------
 1 file changed, 39 insertions(+), 10 deletions(-)
drivers/md/dm.c +39 -10
index e7fc2a69633c..bbde744f7dba 100644
@@ -751,9 +751,16 @@ static struct table_device *open_table_device(struct mapped_device *md,
 		goto out_free_td;
 	}
 
-	r = bd_link_disk_holder(bdev, dm_disk(md));
-	if (r)
-		goto out_blkdev_put;
+	/*
+	 * We can be called before the dm disk is added.  In that case we can't
+	 * register the holder relation here.  It will be done once add_disk was
+	 * called.
+	 */
+	if (md->disk->slave_dir) {
+		r = bd_link_disk_holder(bdev, md->disk);
+		if (r)
+			goto out_blkdev_put;
+	}
 
 	td->dm_dev.mode = mode;
 	td->dm_dev.bdev = bdev;
@@ -774,7 +781,8 @@ static struct table_device *open_table_device(struct mapped_device *md,
  */
 static void close_table_device(struct table_device *td, struct mapped_device *md)
 {
-	bd_unlink_disk_holder(td->dm_dev.bdev, dm_disk(md));
+	if (md->disk->slave_dir)
+		bd_unlink_disk_holder(td->dm_dev.bdev, md->disk);
 	blkdev_put(td->dm_dev.bdev, td->dm_dev.mode | FMODE_EXCL);
 	put_dax(td->dm_dev.dax_dev);
 	list_del(&td->list);
@@ -1964,7 +1972,13 @@ static void cleanup_mapped_device(struct mapped_device *md)
 		md->disk->private_data = NULL;
 		spin_unlock(&_minor_lock);
 		if (dm_get_md_type(md) != DM_TYPE_NONE) {
+			struct table_device *td;
+
 			dm_sysfs_exit(md);
+			list_for_each_entry(td, &md->table_devices, list) {
+				bd_unlink_disk_holder(td->dm_dev.bdev,
+						      md->disk);
+			}
 
 			/*
 			 * Hold lock to make sure del_gendisk() won't concurrent
@@ -2304,6 +2318,7 @@ int dm_setup_md_queue(struct mapped_device *md, struct dm_table *t)
 {
 	enum dm_queue_mode type = dm_table_get_type(t);
 	struct queue_limits limits;
+	struct table_device *td;
 	int r;
 
 	switch (type) {
@@ -2342,16 +2357,30 @@ int dm_setup_md_queue(struct mapped_device *md, struct dm_table *t)
 	if (r)
 		return r;
 
-	r = dm_sysfs_init(md);
-	if (r) {
-		mutex_lock(&md->table_devices_lock);
-		del_gendisk(md->disk);
-		mutex_unlock(&md->table_devices_lock);
-		return r;
+	/*
+	 * Register the holder relationship for devices added before the disk
+	 * was live.
+	 */
+	list_for_each_entry(td, &md->table_devices, list) {
+		r = bd_link_disk_holder(td->dm_dev.bdev, md->disk);
+		if (r)
+			goto out_undo_holders;
 	}
 
+	r = dm_sysfs_init(md);
+	if (r)
+		goto out_undo_holders;
+
 	md->type = type;
 	return 0;
+
+out_undo_holders:
+	list_for_each_entry_continue_reverse(td, &md->table_devices, list)
+		bd_unlink_disk_holder(td->dm_dev.bdev, md->disk);
+	mutex_lock(&md->table_devices_lock);
+	del_gendisk(md->disk);
+	mutex_unlock(&md->table_devices_lock);
+	return r;
 }
 
 struct mapped_device *dm_get_md(dev_t dev)
Signature · 1 line
2.35.1
author maintainer
#334 lore raw

PATCH 335/1073 selftests/bpf: fix memory leak of lsm_cgroup

In reply to Greg Kroah-Hartman

From: Wang Yufen <[email protected]>

[ Upstream commit c453e64cbc9532c0c2edfa999c35d29dad16b8bb ]

kmemleak reports this issue:

unreferenced object 0xffff88810b7835c0 (size 32):
comm "test_progs", pid 270, jiffies 4294969007 (age 1621.315s) hex dump (first 32 bytes):

    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    03 00 00 00 03 00 00 00 0f 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000376cdeab>] kmalloc_trace+0x27/0x110
    [<000000003bcdb3b6>] selinux_sk_alloc_security+0x66/0x110
    [<000000003959008f>] security_sk_alloc+0x47/0x80
    [<00000000e7bc6668>] sk_prot_alloc+0xbd/0x1a0
    [<0000000002d6343a>] sk_alloc+0x3b/0x940
    [<000000009812a46d>] unix_create1+0x8f/0x3d0
    [<000000005ed0976b>] unix_create+0xa1/0x150
    [<0000000086a1d27f>] __sock_create+0x233/0x4a0
    [<00000000cffe3a73>] __sys_socket_create.part.0+0xaa/0x110
    [<0000000007c63f20>] __sys_socket+0x49/0xf0
    [<00000000b08753c8>] __x64_sys_socket+0x42/0x50
    [<00000000b56e26b3>] do_syscall_64+0x3b/0x90
    [<000000009b4871b8>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

The issue occurs in the following scenarios:

unix_create1()
sk_alloc()

    sk_prot_alloc()
      security_sk_alloc()
        call_int_hook()
          hlist_for_each_entry()
            entry1->hook.sk_alloc_security
            <-- selinux_sk_alloc_security() succeeded,
            <-- sk->security alloced here.
            entry2->hook.sk_alloc_security
            <-- bpf_lsm_sk_alloc_security() failed
      goto out_free;
        ...    <-- the sk->security not freed, memleak

The core problem is that the LSM is not yet fully stacked (work is actively going on in this space) which means that some LSM hooks do not support multiple LSMs at the same time. To fix, skip the "EPERM" test when it runs in the environments that already have non-bpf lsms installed

Fixes dca85aac8895 ("selftests/bpf: lsm_cgroup functional test")
Cc Stanislav Fomichev <[email protected]>
---
 .../selftests/bpf/prog_tests/lsm_cgroup.c       | 17 +++++++++++++----
 tools/testing/selftests/bpf/progs/lsm_cgroup.c  |  8 ++++++++
 2 files changed, 21 insertions(+), 4 deletions(-)
tools/testing/selftests/bpf/prog_tests/lsm_cgroup.c +13 -4
index 1102e4f42d2d..f117bfef68a1 100644
@@ -173,10 +173,12 @@ static void test_lsm_cgroup_functional(void)
 	ASSERT_EQ(query_prog_cnt(cgroup_fd, NULL), 4, "total prog count");
 	ASSERT_EQ(query_prog_cnt(cgroup_fd2, NULL), 1, "total prog count");
 
-	/* AF_UNIX is prohibited. */
-
 	fd = socket(AF_UNIX, SOCK_STREAM, 0);
-	ASSERT_LT(fd, 0, "socket(AF_UNIX)");
+	if (!(skel->kconfig->CONFIG_SECURITY_APPARMOR
+	    || skel->kconfig->CONFIG_SECURITY_SELINUX
+	    || skel->kconfig->CONFIG_SECURITY_SMACK))
+		/* AF_UNIX is prohibited. */
+		ASSERT_LT(fd, 0, "socket(AF_UNIX)");
 	close(fd);
 
 	/* AF_INET6 gets default policy (sk_priority). */
@@ -233,11 +235,18 @@ static void test_lsm_cgroup_functional(void)
 
 	/* AF_INET6+SOCK_STREAM
 	 * AF_PACKET+SOCK_RAW
+	 * AF_UNIX+SOCK_RAW if already have non-bpf lsms installed
 	 * listen_fd
 	 * client_fd
 	 * accepted_fd
 	 */
-	ASSERT_EQ(skel->bss->called_socket_post_create2, 5, "called_create2");
+	if (skel->kconfig->CONFIG_SECURITY_APPARMOR
+	    || skel->kconfig->CONFIG_SECURITY_SELINUX
+	    || skel->kconfig->CONFIG_SECURITY_SMACK)
+		/* AF_UNIX+SOCK_RAW if already have non-bpf lsms installed */
+		ASSERT_EQ(skel->bss->called_socket_post_create2, 6, "called_create2");
+	else
+		ASSERT_EQ(skel->bss->called_socket_post_create2, 5, "called_create2");
 
 	/* start_server
 	 * bind(ETH_P_ALL)
tools/testing/selftests/bpf/progs/lsm_cgroup.c +8 -0
index 4f2d60b87b75..02c11d16b692 100644
@@ -7,6 +7,10 @@
 
 char _license[] SEC("license") = "GPL";
 
+extern bool CONFIG_SECURITY_SELINUX __kconfig __weak;
+extern bool CONFIG_SECURITY_SMACK __kconfig __weak;
+extern bool CONFIG_SECURITY_APPARMOR __kconfig __weak;
+
 #ifndef AF_PACKET
 #define AF_PACKET 17
 #endif
@@ -140,6 +144,10 @@ SEC("lsm_cgroup/sk_alloc_security")
 int BPF_PROG(socket_alloc, struct sock *sk, int family, gfp_t priority)
 {
 	called_socket_alloc++;
+	/* if already have non-bpf lsms installed, EPERM will cause memory leak of non-bpf lsms */
+	if (CONFIG_SECURITY_SELINUX || CONFIG_SECURITY_SMACK || CONFIG_SECURITY_APPARMOR)
+		return 1;
+
 	if (family == AF_UNIX)
 		return 0; /* EPERM */
 
Signature · 1 line
2.35.1
author maintainer
#335 lore raw

PATCH 336/1073 wifi: ath10k: Fix return value in ath10k_pci_init()

In reply to Greg Kroah-Hartman

From: Xiu Jianfeng <[email protected]>

[ Upstream commit 2af7749047d8d6ad43feff69f555a13a6a6c2831 ]

This driver is attempting to register to support two different buses. if either of these is successful then ath10k_pci_init() should return 0 so that hardware attached to the successful bus can be probed and supported. only if both of these are unsuccessful should ath10k_pci_init() return an errno.

Fixes 0b523ced9a3c ("ath10k: add basic skeleton to support ahb")
---
 drivers/net/wireless/ath/ath10k/pci.c | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)
drivers/net/wireless/ath/ath10k/pci.c +12 -8
index bf1c938be7d0..8015b457a870 100644
@@ -3793,18 +3793,22 @@ static struct pci_driver ath10k_pci_driver = {
 
 static int __init ath10k_pci_init(void)
 {
-	int ret;
+	int ret1, ret2;
 
-	ret = pci_register_driver(&ath10k_pci_driver);
-	if (ret)
+	ret1 = pci_register_driver(&ath10k_pci_driver);
+	if (ret1)
 		printk(KERN_ERR "failed to register ath10k pci driver: %d\n",
-		       ret);
+		       ret1);
 
-	ret = ath10k_ahb_init();
-	if (ret)
-		printk(KERN_ERR "ahb init failed: %d\n", ret);
+	ret2 = ath10k_ahb_init();
+	if (ret2)
+		printk(KERN_ERR "ahb init failed: %d\n", ret2);
 
-	return ret;
+	if (ret1 && ret2)
+		return ret1;
+
+	/* registered to at least one bus */
+	return 0;
 }
 module_init(ath10k_pci_init);
 
Signature · 1 line
2.35.1
author maintainer
#336 lore raw

PATCH 337/1073 drm/msm/a6xx: Fix speed-bin detection vs probe-defer

In reply to Greg Kroah-Hartman

From: Rob Clark <[email protected]>

[ Upstream commit f6d1918794ef92b4e26b80c3d40365347b76b1fd ]

If we get an error (other than -ENOENT) we need to propagate that up the stack. Otherwise if the nvmem driver hasn't probed yet, we'll end up end up claiming that we support all the OPPs which is not likely to be true (and on some generations impossible to be true, ie. if there are conflicting OPPs).

v2: Update commit msg, gc unused label, etc
v3: Add previously missing \n's

Fixes fe7952c629da ("drm/msm: Add speed-bin support to a618 gpu")

Patchwork: https://patchwork.freedesktop.org/patch/511690/

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +5 -7
index 4d501100b9e4..5804c35ae74b 100644
@@ -1869,7 +1869,7 @@ static u32 fuse_to_supp_hw(struct device *dev, struct adreno_rev rev, u32 fuse)
 
 	if (val == UINT_MAX) {
 		DRM_DEV_ERROR(dev,
-			"missing support for speed-bin: %u. Some OPPs may not be supported by hardware",
+			"missing support for speed-bin: %u. Some OPPs may not be supported by hardware\n",
 			fuse);
 		return UINT_MAX;
 	}
@@ -1879,7 +1879,7 @@ static u32 fuse_to_supp_hw(struct device *dev, struct adreno_rev rev, u32 fuse)
 
 static int a6xx_set_supported_hw(struct device *dev, struct adreno_rev rev)
 {
-	u32 supp_hw = UINT_MAX;
+	u32 supp_hw;
 	u32 speedbin;
 	int ret;
 
@@ -1891,15 +1891,13 @@ static int a6xx_set_supported_hw(struct device *dev, struct adreno_rev rev)
 	if (ret == -ENOENT) {
 		return 0;
 	} else if (ret) {
-		DRM_DEV_ERROR(dev,
-			      "failed to read speed-bin (%d). Some OPPs may not be supported by hardware",
-			      ret);
-		goto done;
+		dev_err_probe(dev, ret,
+			      "failed to read speed-bin. Some OPPs may not be supported by hardware\n");
+		return ret;
 	}
 
 	supp_hw = fuse_to_supp_hw(dev, rev, speedbin);
 
-done:
 	ret = devm_pm_opp_set_supported_hw(dev, &supp_hw, 1);
 	if (ret)
 		return ret;
Signature · 1 line
2.35.1
author maintainer
#337 lore raw

PATCH 338/1073 mtd: lpddr2_nvm: Fix possible null-ptr-deref

In reply to Greg Kroah-Hartman

From: Hui Tang <[email protected]>

[ Upstream commit 6bdd45d795adf9e73b38ced5e7f750cd199499ff ]

It will cause null-ptr-deref when resource_size(add_range) invoked, if platform_get_resource() returns NULL.

Fixes 96ba9dd65788 ("mtd: lpddr: add driver for LPDDR2-NVM PCM memories")
---
 drivers/mtd/lpddr/lpddr2_nvm.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/mtd/lpddr/lpddr2_nvm.c +2 -0
index 367e2d906de0..e71af4c49096 100644
@@ -433,6 +433,8 @@ static int lpddr2_nvm_probe(struct platform_device *pdev)
 
 	/* lpddr2_nvm address range */
 	add_range = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!add_range)
+		return -ENODEV;
 
 	/* Populate map_info data structure */
 	*map = (struct map_info) {
Signature · 1 line
2.35.1
author maintainer
#338 lore raw

PATCH 339/1073 Input: elants_i2c - properly handle the reset GPIO when power is off

In reply to Greg Kroah-Hartman

From: Douglas Anderson <[email protected]>

[ Upstream commit a85fbd6498441694475716a4d5c65f9d3e073faf ]

As can be seen in elants_i2c_power_off(), we want the reset GPIO asserted when power is off. The reset GPIO is active low so we need the reset line logic low when power is off to avoid leakage.

We have a problem, though, at probe time. At probe time we haven't powered the regulators on yet but we have:

  devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);

While that _looks_ right, it turns out that it's not. The GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the GPIO to "not asserted". Since this is an active low GPIO that inits it to be high.

Let's fix this to properly init the GPIO. Now after both probe and power off the state of the GPIO is consistent (it's "asserted" or level low).

Once we fix this, we can see that at power on time we no longer to assert the reset GPIO as the first thing. The reset GPIO is _always_ asserted before powering on. Let's fix powering on to account for this.

---
 drivers/input/touchscreen/elants_i2c.c | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)
drivers/input/touchscreen/elants_i2c.c +3 -6
index 879a4d984c90..e1308e179dd6 100644
@@ -1329,14 +1329,12 @@ static int elants_i2c_power_on(struct elants_data *ts)
 	if (IS_ERR_OR_NULL(ts->reset_gpio))
 		return 0;
 
-	gpiod_set_value_cansleep(ts->reset_gpio, 1);
-
 	error = regulator_enable(ts->vcc33);
 	if (error) {
 		dev_err(&ts->client->dev,
 			"failed to enable vcc33 regulator: %d\n",
 			error);
-		goto release_reset_gpio;
+		return error;
 	}
 
 	error = regulator_enable(ts->vccio);
@@ -1345,7 +1343,7 @@ static int elants_i2c_power_on(struct elants_data *ts)
 			"failed to enable vccio regulator: %d\n",
 			error);
 		regulator_disable(ts->vcc33);
-		goto release_reset_gpio;
+		return error;
 	}
 
 	/*
@@ -1354,7 +1352,6 @@ static int elants_i2c_power_on(struct elants_data *ts)
 	 */
 	udelay(ELAN_POWERON_DELAY_USEC);
 
-release_reset_gpio:
 	gpiod_set_value_cansleep(ts->reset_gpio, 0);
 	if (error)
 		return error;
@@ -1462,7 +1459,7 @@ static int elants_i2c_probe(struct i2c_client *client)
 		return error;
 	}
 
-	ts->reset_gpio = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+	ts->reset_gpio = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(ts->reset_gpio)) {
 		error = PTR_ERR(ts->reset_gpio);
 
Signature · 1 line
2.35.1
author maintainer
#339 lore raw

PATCH 340/1073 net: ethernet: mtk_eth_soc: do not overwrite mtu configuration running reset routine

In reply to Greg Kroah-Hartman

From: Lorenzo Bianconi <[email protected]>

[ Upstream commit b677d6c7a695dad1b02d2e0e428c39b3b344f270 ]

Restore user configured MTU running mtk_hw_init() during tx timeout routine since it will be overwritten after a hw reset.

Fixes 9ea4d311509f ("net: ethernet: mediatek: add the whole ethernet reset into the reset process")
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 53 +++++++++++++--------
 1 file changed, 34 insertions(+), 19 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +34 -19
index 5380caf0acc2..26e0a2af64cf 100644
@@ -3209,6 +3209,30 @@ static void mtk_dim_tx(struct work_struct *work)
 	dim->state = DIM_START_MEASURE;
 }
 
+static void mtk_set_mcr_max_rx(struct mtk_mac *mac, u32 val)
+{
+	struct mtk_eth *eth = mac->hw;
+	u32 mcr_cur, mcr_new;
+
+	if (MTK_HAS_CAPS(eth->soc->caps, MTK_SOC_MT7628))
+		return;
+
+	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
+	mcr_new = mcr_cur & ~MAC_MCR_MAX_RX_MASK;
+
+	if (val <= 1518)
+		mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_1518);
+	else if (val <= 1536)
+		mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_1536);
+	else if (val <= 1552)
+		mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_1552);
+	else
+		mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_2048);
+
+	if (mcr_new != mcr_cur)
+		mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
+}
+
 static int mtk_hw_init(struct mtk_eth *eth)
 {
 	u32 dma_mask = ETHSYS_DMA_AG_MAP_PDMA | ETHSYS_DMA_AG_MAP_QDMA |
@@ -3283,8 +3307,16 @@ static int mtk_hw_init(struct mtk_eth *eth)
 	 * up with the more appropriate value when mtk_mac_config call is being
 	 * invoked.
 	 */
-	for (i = 0; i < MTK_MAC_COUNT; i++)
+	for (i = 0; i < MTK_MAC_COUNT; i++) {
+		struct net_device *dev = eth->netdev[i];
+
 		mtk_w32(eth, MAC_MCR_FORCE_LINK_DOWN, MTK_MAC_MCR(i));
+		if (dev) {
+			struct mtk_mac *mac = netdev_priv(dev);
+
+			mtk_set_mcr_max_rx(mac, dev->mtu + MTK_RX_ETH_HLEN);
+		}
+	}
 
 	/* Indicates CDM to parse the MTK special tag from CPU
 	 * which also is working out for untag packets.
@@ -3400,7 +3432,6 @@ static int mtk_change_mtu(struct net_device *dev, int new_mtu)
 	int length = new_mtu + MTK_RX_ETH_HLEN;
 	struct mtk_mac *mac = netdev_priv(dev);
 	struct mtk_eth *eth = mac->hw;
-	u32 mcr_cur, mcr_new;
 
 	if (rcu_access_pointer(eth->prog) &&
 	    length > MTK_PP_MAX_BUF_SIZE) {
@@ -3408,23 +3439,7 @@ static int mtk_change_mtu(struct net_device *dev, int new_mtu)
 		return -EINVAL;
 	}
 
-	if (!MTK_HAS_CAPS(eth->soc->caps, MTK_SOC_MT7628)) {
-		mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
-		mcr_new = mcr_cur & ~MAC_MCR_MAX_RX_MASK;
-
-		if (length <= 1518)
-			mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_1518);
-		else if (length <= 1536)
-			mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_1536);
-		else if (length <= 1552)
-			mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_1552);
-		else
-			mcr_new |= MAC_MCR_MAX_RX(MAC_MCR_MAX_RX_2048);
-
-		if (mcr_new != mcr_cur)
-			mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
-	}
-
+	mtk_set_mcr_max_rx(mac, length);
 	dev->mtu = new_mtu;
 
 	return 0;
Signature · 1 line
2.35.1
author maintainer
#340 lore raw

PATCH 341/1073 media: amphion: add lock around vdec_g_fmt

In reply to Greg Kroah-Hartman

From: Ming Qian <[email protected]>

[ Upstream commit 8480dd5fb3c82b5887d456b3fbe4201d99231814 ]

the capture format may be changed when
sequence header is parsed,
it may be read and write in the same time,
add lock around vdec_g_fmt to synchronize it

Fixes 6de8d628df6e ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
---
 drivers/media/platform/amphion/vdec.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/media/platform/amphion/vdec.c +2 -0
index 84c90ce265f2..b27e6bed85f0 100644
@@ -286,6 +286,7 @@ static int vdec_g_fmt(struct file *file, void *fh, struct v4l2_format *f)
 	struct vpu_format *cur_fmt;
 	int i;
 
+	vpu_inst_lock(inst);
 	cur_fmt = vpu_get_format(inst, f->type);
 
 	pixmp->pixelformat = cur_fmt->pixfmt;
@@ -303,6 +304,7 @@ static int vdec_g_fmt(struct file *file, void *fh, struct v4l2_format *f)
 	f->fmt.pix_mp.xfer_func = vdec->codec_info.transfer_chars;
 	f->fmt.pix_mp.ycbcr_enc = vdec->codec_info.matrix_coeffs;
 	f->fmt.pix_mp.quantization = vdec->codec_info.full_range;
+	vpu_inst_unlock(inst);
 
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#341 lore raw

PATCH 342/1073 media: amphion: apply vb2_queue_error instead of setting manually

In reply to Greg Kroah-Hartman

From: Ming Qian <[email protected]>

[ Upstream commit 9d175a81e28f260916a0a13f457dd8b940eafb4e ]

vb2_queue_error is help to set the error of vb2_queue, don't need to set it manually

Fixes 3cd084519c6f ("media: amphion: add vpu v4l2 m2m support")
---
 drivers/media/platform/amphion/vpu_v4l2.c | 11 ++---------
 1 file changed, 2 insertions(+), 9 deletions(-)
drivers/media/platform/amphion/vpu_v4l2.c +2 -9
index b779e0ba916c..4b714fab4c6b 100644
@@ -65,18 +65,11 @@ unsigned int vpu_get_buffer_state(struct vb2_v4l2_buffer *vbuf)
 
 void vpu_v4l2_set_error(struct vpu_inst *inst)
 {
-	struct vb2_queue *src_q;
-	struct vb2_queue *dst_q;
-
 	vpu_inst_lock(inst);
 	dev_err(inst->dev, "some error occurs in codec\n");
 	if (inst->fh.m2m_ctx) {
-		src_q = v4l2_m2m_get_src_vq(inst->fh.m2m_ctx);
-		dst_q = v4l2_m2m_get_dst_vq(inst->fh.m2m_ctx);
-		src_q->error = 1;
-		dst_q->error = 1;
-		wake_up(&src_q->done_wq);
-		wake_up(&dst_q->done_wq);
+		vb2_queue_error(v4l2_m2m_get_src_vq(inst->fh.m2m_ctx));
+		vb2_queue_error(v4l2_m2m_get_dst_vq(inst->fh.m2m_ctx));
 	}
 	vpu_inst_unlock(inst);
 }
Signature · 1 line
2.35.1
author maintainer
#342 lore raw

PATCH 343/1073 media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init()

In reply to Greg Kroah-Hartman

From: Chen Zhongjin <[email protected]>

[ Upstream commit ba8d9405935097e296bcf7a942c3a01df0edb865 ]

KASAN reports a use-after-free:

BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
Call Trace:
 ...
 dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
 vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge]
 platform_probe+0xb6/0x170
 ...
Allocated by task 1238:
 ...
 dvb_register_device+0x1a7/0xa70 [dvb_core]
 dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
 vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
 ...
Freed by task 1238:
 dvb_register_device+0x6d2/0xa70 [dvb_core]
 dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
 vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
 ...

It is because the error handling in vidtv_bridge_dvb_init() is wrong.

First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but goto fail_dmx(_dev): calls release functions again, which causes use-after-free.

Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause out-of-bound when i finished its loop (i == NUM_FE). And the loop releasing is wrong, although now NUM_FE is 1 so it won't cause problem.

Fix this by correctly releasing everything.

Fixes f90cf6079bf6 ("media: vidtv: add a bridge driver")
---
 .../media/test-drivers/vidtv/vidtv_bridge.c   | 22 +++++++------------
 1 file changed, 8 insertions(+), 14 deletions(-)
drivers/media/test-drivers/vidtv/vidtv_bridge.c +8 -14
index 82620613d56b..dff7265a42ca 100644
@@ -459,26 +459,20 @@ static int vidtv_bridge_dvb_init(struct vidtv_dvb *dvb)
 	for (j = j - 1; j >= 0; --j)
 		dvb->demux.dmx.remove_frontend(&dvb->demux.dmx,
 					       &dvb->dmx_fe[j]);
-fail_dmx_dev:
 	dvb_dmxdev_release(&dvb->dmx_dev);
-fail_dmx:
+fail_dmx_dev:
 	dvb_dmx_release(&dvb->demux);
+fail_dmx:
+fail_demod_probe:
+	for (i = i - 1; i >= 0; --i) {
+		dvb_unregister_frontend(dvb->fe[i]);
 fail_fe:
-	for (j = i; j >= 0; --j)
-		dvb_unregister_frontend(dvb->fe[j]);
+		dvb_module_release(dvb->i2c_client_tuner[i]);
 fail_tuner_probe:
-	for (j = i; j >= 0; --j)
-		if (dvb->i2c_client_tuner[j])
-			dvb_module_release(dvb->i2c_client_tuner[j]);
-
-fail_demod_probe:
-	for (j = i; j >= 0; --j)
-		if (dvb->i2c_client_demod[j])
-			dvb_module_release(dvb->i2c_client_demod[j]);
-
+		dvb_module_release(dvb->i2c_client_demod[i]);
+	}
 fail_adapter:
 	dvb_unregister_adapter(&dvb->adapter);
-
 fail_i2c:
 	i2c_del_adapter(&dvb->i2c_adapter);
 
Signature · 1 line
2.35.1
author maintainer
#343 lore raw

PATCH 344/1073 media: solo6x10: fix possible memory leak in solo_sysfs_init()

In reply to Greg Kroah-Hartman

From: Yang Yingliang <[email protected]>

[ Upstream commit 7f5866dd96d95b74e439f6ee17b8abd8195179fb ]

If device_register() returns error in solo_sysfs_init(), the name allocated by dev_set_name() need be freed. As comment of device_register() says, it should use put_device() to give up the reference in the error path. So fix this by calling put_device(), then the name can be freed in kobject_cleanup().

Fixes dcae5dacbce5 ("[media] solo6x10: sync to latest code from Bluecherry's git repo")
---
 drivers/media/pci/solo6x10/solo6x10-core.c | 1 +
 1 file changed, 1 insertion(+)
drivers/media/pci/solo6x10/solo6x10-core.c +1 -0
index 4a546eeefe38..6d87fbb0ee04 100644
@@ -420,6 +420,7 @@ static int solo_sysfs_init(struct solo_dev *solo_dev)
 		     solo_dev->nr_chans);
 
 	if (device_register(dev)) {
+		put_device(dev);
 		dev->parent = NULL;
 		return -ENOMEM;
 	}
Signature · 1 line
2.35.1
author maintainer
#344 lore raw

PATCH 345/1073 media: platform: exynos4-is: Fix error handling in fimc_md_init()

In reply to Greg Kroah-Hartman

From: Yuan Can <[email protected]>

[ Upstream commit b434422c45282a0573d8123239abc41fa72665d4 ]

A problem about modprobe s5p_fimc failed is triggered with the following log given:

 [  272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
 modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy

The reason is that fimc_md_init() returns platform_driver_register() directly without checking its return value, if platform_driver_register() failed, it returns without unregister fimc_driver, resulting the s5p_fimc can never be installed later.
A simple call graph is shown as below:

fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened

   # return without unregister fimc_driver

Fix by unregister fimc_driver when platform_driver_register() returns error.

Fixes d3953223b090 ("[media] s5p-fimc: Add the media device driver")
---
 drivers/media/platform/samsung/exynos4-is/fimc-core.c | 2 +-
 drivers/media/platform/samsung/exynos4-is/media-dev.c | 6 +++++-
 2 files changed, 6 insertions(+), 2 deletions(-)
drivers/media/platform/samsung/exynos4-is/fimc-core.c +1 -1
index 91cc8d58a663..1791100b6935 100644
@@ -1173,7 +1173,7 @@ int __init fimc_register_driver(void)
 	return platform_driver_register(&fimc_driver);
 }
 
-void __exit fimc_unregister_driver(void)
+void fimc_unregister_driver(void)
 {
 	platform_driver_unregister(&fimc_driver);
 }
drivers/media/platform/samsung/exynos4-is/media-dev.c +5 -1
index 383a1e0ab912..2f3071acb9c9 100644
@@ -1584,7 +1584,11 @@ static int __init fimc_md_init(void)
 	if (ret)
 		return ret;
 
-	return platform_driver_register(&fimc_md_driver);
+	ret = platform_driver_register(&fimc_md_driver);
+	if (ret)
+		fimc_unregister_driver();
+
+	return ret;
 }
 
 static void __exit fimc_md_exit(void)
Signature · 1 line
2.35.1
author maintainer
#345 lore raw

PATCH 346/1073 media: amphion: Fix error handling in vpu_driver_init()

In reply to Greg Kroah-Hartman

From: Yuan Can <[email protected]>

[ Upstream commit a95cc6d11aae16a7b2d043b073a40de81bbea689 ]

A problem about modprobe amphion-vpu failed is triggered with the following log given:

 [ 2208.634841] Error: Driver 'amphion-vpu' is already registered, aborting...
 modprobe: ERROR: could not insert 'amphion_vpu': Device or resource busy

The reason is that vpu_driver_init() returns vpu_core_driver_init() directly without checking its return value, if vpu_core_driver_init() failed, it returns without unregister amphion_vpu_driver, resulting the amphion-vpu can never be installed later.
A simple call graph is shown as below:

vpu_driver_init()
platform_driver_register() # register amphion_vpu_driver vpu_core_driver_init()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened

   # return without unregister amphion_vpu_driver

Fix by unregister amphion_vpu_driver when vpu_core_driver_init() returns error.

Fixes b50a64fc54af ("media: amphion: add amphion vpu device driver")
---
 drivers/media/platform/amphion/vpu_drv.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/media/platform/amphion/vpu_drv.c +5 -1
index 9d5a5075343d..f01ce49d27e8 100644
@@ -245,7 +245,11 @@ static int __init vpu_driver_init(void)
 	if (ret)
 		return ret;
 
-	return vpu_core_driver_init();
+	ret = vpu_core_driver_init();
+	if (ret)
+		platform_driver_unregister(&amphion_vpu_driver);
+
+	return ret;
 }
 
 static void __exit vpu_driver_exit(void)
Signature · 1 line
2.35.1
author maintainer
#346 lore raw

PATCH 347/1073 media: videobuf-dma-contig: use dma_mmap_coherent

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

[ Upstream commit b3dc3f8e49577840dc8ac8a365c5b3da4edb10b8 ]

dma_alloc_coherent does not return a physical address, but a DMA address, which might be remapped or have an offset. Passing the DMA address to vm_iomap_memory is thus broken.

Use the proper dma_mmap_coherent helper instead, and stop passing __GFP_COMP to dma_alloc_coherent, as the memory management inside the DMA allocator is hidden from the callers and does not require it.

With this the gfp_t argument to __videobuf_dc_alloc can be removed and hard coded to GFP_KERNEL.

Fixes a8f3c203e19b ("[media] videobuf-dma-contig: add cache support")
---
 drivers/media/v4l2-core/videobuf-dma-contig.c | 22 +++++++------------
 1 file changed, 8 insertions(+), 14 deletions(-)
drivers/media/v4l2-core/videobuf-dma-contig.c +8 -14
index 52312ce2ba05..f2c439359557 100644
@@ -36,12 +36,11 @@ struct videobuf_dma_contig_memory {
 
 static int __videobuf_dc_alloc(struct device *dev,
 			       struct videobuf_dma_contig_memory *mem,
-			       unsigned long size, gfp_t flags)
+			       unsigned long size)
 {
 	mem->size = size;
-	mem->vaddr = dma_alloc_coherent(dev, mem->size,
-					&mem->dma_handle, flags);
-
+	mem->vaddr = dma_alloc_coherent(dev, mem->size, &mem->dma_handle,
+					GFP_KERNEL);
 	if (!mem->vaddr) {
 		dev_err(dev, "memory alloc size %ld failed\n", mem->size);
 		return -ENOMEM;
@@ -258,8 +257,7 @@ static int __videobuf_iolock(struct videobuf_queue *q,
 			return videobuf_dma_contig_user_get(mem, vb);
 
 		/* allocate memory for the read() method */
-		if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(vb->size),
-					GFP_KERNEL))
+		if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(vb->size)))
 			return -ENOMEM;
 		break;
 	case V4L2_MEMORY_OVERLAY:
@@ -295,22 +293,18 @@ static int __videobuf_mmap_mapper(struct videobuf_queue *q,
 	BUG_ON(!mem);
 	MAGIC_CHECK(mem->magic, MAGIC_DC_MEM);
 
-	if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(buf->bsize),
-				GFP_KERNEL | __GFP_COMP))
+	if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(buf->bsize)))
 		goto error;
 
-	/* Try to remap memory */
-	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
-
 	/* the "vm_pgoff" is just used in v4l2 to find the
 	 * corresponding buffer data structure which is allocated
 	 * earlier and it does not mean the offset from the physical
 	 * buffer start address as usual. So set it to 0 to pass
-	 * the sanity check in vm_iomap_memory().
+	 * the sanity check in dma_mmap_coherent().
 	 */
 	vma->vm_pgoff = 0;
-
-	retval = vm_iomap_memory(vma, mem->dma_handle, mem->size);
+	retval = dma_mmap_coherent(q->dev, vma, mem->vaddr, mem->dma_handle,
+				   mem->size);
 	if (retval) {
 		dev_err(q->dev, "mmap: remap failed with error %d. ",
 			retval);
Signature · 1 line
2.35.1
author maintainer
#347 lore raw

PATCH 348/1073 net: ethernet: mtk_eth_soc: fix RSTCTRL_PPE{0,1} definitions

In reply to Greg Kroah-Hartman

From: Lorenzo Bianconi <[email protected]>

[ Upstream commit ef8c373bd91df3cf70596497da0955d218961ead ]

Fix RSTCTRL_PPE0 and RSTCTRL_PPE1 register mask definitions for MTK_NETSYS_V2.
Remove duplicated definitions.

Fixes 160d3a9b1929 ("net: ethernet: mtk_eth_soc: introduce MTK_NETSYS_V2 support")
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 13 +++++++------
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 10 +++-------
 2 files changed, 10 insertions(+), 13 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +7 -6
index 26e0a2af64cf..4c16f2df566f 100644
@@ -3272,16 +3272,17 @@ static int mtk_hw_init(struct mtk_eth *eth)
 		return 0;
 	}
 
-	val = RSTCTRL_FE | RSTCTRL_PPE;
 	if (MTK_HAS_CAPS(eth->soc->caps, MTK_NETSYS_V2)) {
 		regmap_write(eth->ethsys, ETHSYS_FE_RST_CHK_IDLE_EN, 0);
-
-		val |= RSTCTRL_ETH;
-		if (MTK_HAS_CAPS(eth->soc->caps, MTK_RSTCTRL_PPE1))
-			val |= RSTCTRL_PPE1;
+		val = RSTCTRL_PPE0_V2;
+	} else {
+		val = RSTCTRL_PPE0;
 	}
 
-	ethsys_reset(eth, val);
+	if (MTK_HAS_CAPS(eth->soc->caps, MTK_RSTCTRL_PPE1))
+		val |= RSTCTRL_PPE1;
+
+	ethsys_reset(eth, RSTCTRL_ETH | RSTCTRL_FE | val);
 
 	if (MTK_HAS_CAPS(eth->soc->caps, MTK_NETSYS_V2)) {
 		regmap_write(eth->ethsys, ETHSYS_FE_RST_CHK_IDLE_EN,
drivers/net/ethernet/mediatek/mtk_eth_soc.h +3 -7
index 0f9668a4079d..da261dd49d6f 100644
@@ -451,18 +451,14 @@
 /* ethernet reset control register */
 #define ETHSYS_RSTCTRL			0x34
 #define RSTCTRL_FE			BIT(6)
-#define RSTCTRL_PPE			BIT(31)
-#define RSTCTRL_PPE1			BIT(30)
+#define RSTCTRL_PPE0			BIT(31)
+#define RSTCTRL_PPE0_V2			BIT(30)
+#define RSTCTRL_PPE1			BIT(31)
 #define RSTCTRL_ETH			BIT(23)
 
 /* ethernet reset check idle register */
 #define ETHSYS_FE_RST_CHK_IDLE_EN	0x28
 
-/* ethernet reset control register */
-#define ETHSYS_RSTCTRL		0x34
-#define RSTCTRL_FE		BIT(6)
-#define RSTCTRL_PPE		BIT(31)
-
 /* ethernet dma channel agent map */
 #define ETHSYS_DMA_AG_MAP	0x408
 #define ETHSYS_DMA_AG_MAP_PDMA	BIT(0)
Signature · 1 line
2.35.1
author maintainer
#348 lore raw

PATCH 349/1073 udp: Clean up some functions.

In reply to Greg Kroah-Hartman

From: Kuniyuki Iwashima <[email protected]>

[ Upstream commit 919dfa0b20ae56060dce0436eb710717f8987d18 ]

This patch adds no functional change and cleans up some functions that the following patches touch around so that we make them tidy and easy to review/revert. The change is mainly to keep reverse christmas tree order.

Stable-dep-of: 7a7160edf1bf ("net: Return errno in sk->sk_prot->get_port().")

---
 net/ipv4/udp.c | 39 +++++++++++++++++++++++----------------
 net/ipv6/udp.c | 12 ++++++++----
 2 files changed, 31 insertions(+), 20 deletions(-)
net/ipv4/udp.c +23 -16
index d9099754ac69..c04a26339bd1 100644
@@ -232,16 +232,16 @@ static int udp_reuseport_add_sock(struct sock *sk, struct udp_hslot *hslot)
 int udp_lib_get_port(struct sock *sk, unsigned short snum,
 		     unsigned int hash2_nulladdr)
 {
-	struct udp_hslot *hslot, *hslot2;
 	struct udp_table *udptable = sk->sk_prot->h.udp_table;
-	int    error = 1;
+	struct udp_hslot *hslot, *hslot2;
 	struct net *net = sock_net(sk);
+	int error = 1;
 
 	if (!snum) {
+		DECLARE_BITMAP(bitmap, PORTS_PER_CHAIN);
+		unsigned short first, last;
 		int low, high, remaining;
 		unsigned int rand;
-		unsigned short first, last;
-		DECLARE_BITMAP(bitmap, PORTS_PER_CHAIN);
 
 		inet_get_local_port_range(net, &low, &high);
 		remaining = (high - low) + 1;
@@ -2527,10 +2527,13 @@ static struct sock *__udp4_lib_mcast_demux_lookup(struct net *net,
 						  __be16 rmt_port, __be32 rmt_addr,
 						  int dif, int sdif)
 {
-	struct sock *sk, *result;
 	unsigned short hnum = ntohs(loc_port);
-	unsigned int slot = udp_hashfn(net, hnum, udp_table.mask);
-	struct udp_hslot *hslot = &udp_table.hash[slot];
+	struct sock *sk, *result;
+	struct udp_hslot *hslot;
+	unsigned int slot;
+
+	slot = udp_hashfn(net, hnum, udp_table.mask);
+	hslot = &udp_table.hash[slot];
 
 	/* Do not bother scanning a too big list */
 	if (hslot->count > 10)
@@ -2558,14 +2561,18 @@ static struct sock *__udp4_lib_demux_lookup(struct net *net,
 					    __be16 rmt_port, __be32 rmt_addr,
 					    int dif, int sdif)
 {
-	unsigned short hnum = ntohs(loc_port);
-	unsigned int hash2 = ipv4_portaddr_hash(net, loc_addr, hnum);
-	unsigned int slot2 = hash2 & udp_table.mask;
-	struct udp_hslot *hslot2 = &udp_table.hash2[slot2];
 	INET_ADDR_COOKIE(acookie, rmt_addr, loc_addr);
-	const __portpair ports = INET_COMBINED_PORTS(rmt_port, hnum);
+	unsigned short hnum = ntohs(loc_port);
+	unsigned int hash2, slot2;
+	struct udp_hslot *hslot2;
+	__portpair ports;
 	struct sock *sk;
 
+	hash2 = ipv4_portaddr_hash(net, loc_addr, hnum);
+	slot2 = hash2 & udp_table.mask;
+	hslot2 = &udp_table.hash2[slot2];
+	ports = INET_COMBINED_PORTS(rmt_port, hnum);
+
 	udp_portaddr_for_each_entry_rcu(sk, &hslot2->head) {
 		if (inet_match(net, sk, acookie, ports, dif, sdif))
 			return sk;
@@ -2966,10 +2973,10 @@ EXPORT_SYMBOL(udp_prot);
 
 static struct sock *udp_get_first(struct seq_file *seq, int start)
 {
-	struct sock *sk;
-	struct udp_seq_afinfo *afinfo;
 	struct udp_iter_state *state = seq->private;
 	struct net *net = seq_file_net(seq);
+	struct udp_seq_afinfo *afinfo;
+	struct sock *sk;
 
 	if (state->bpf_seq_afinfo)
 		afinfo = state->bpf_seq_afinfo;
@@ -3000,9 +3007,9 @@ static struct sock *udp_get_first(struct seq_file *seq, int start)
 
 static struct sock *udp_get_next(struct seq_file *seq, struct sock *sk)
 {
-	struct udp_seq_afinfo *afinfo;
 	struct udp_iter_state *state = seq->private;
 	struct net *net = seq_file_net(seq);
+	struct udp_seq_afinfo *afinfo;
 
 	if (state->bpf_seq_afinfo)
 		afinfo = state->bpf_seq_afinfo;
@@ -3058,8 +3065,8 @@ EXPORT_SYMBOL(udp_seq_next);
 
 void udp_seq_stop(struct seq_file *seq, void *v)
 {
-	struct udp_seq_afinfo *afinfo;
 	struct udp_iter_state *state = seq->private;
+	struct udp_seq_afinfo *afinfo;
 
 	if (state->bpf_seq_afinfo)
 		afinfo = state->bpf_seq_afinfo;
net/ipv6/udp.c +8 -4
index fb667e02e976..d917d62e662d 100644
@@ -1039,12 +1039,16 @@ static struct sock *__udp6_lib_demux_lookup(struct net *net,
 			int dif, int sdif)
 {
 	unsigned short hnum = ntohs(loc_port);
-	unsigned int hash2 = ipv6_portaddr_hash(net, loc_addr, hnum);
-	unsigned int slot2 = hash2 & udp_table.mask;
-	struct udp_hslot *hslot2 = &udp_table.hash2[slot2];
-	const __portpair ports = INET_COMBINED_PORTS(rmt_port, hnum);
+	unsigned int hash2, slot2;
+	struct udp_hslot *hslot2;
+	__portpair ports;
 	struct sock *sk;
 
+	hash2 = ipv6_portaddr_hash(net, loc_addr, hnum);
+	slot2 = hash2 & udp_table.mask;
+	hslot2 = &udp_table.hash2[slot2];
+	ports = INET_COMBINED_PORTS(rmt_port, hnum);
+
 	udp_portaddr_for_each_entry_rcu(sk, &hslot2->head) {
 		if (sk->sk_state == TCP_ESTABLISHED &&
 		    inet6_match(net, sk, rmt_addr, loc_addr, ports, dif, sdif))
Signature · 1 line
2.35.1
author maintainer
#349 lore raw

PATCH 350/1073 net: Return errno in sk->sk_prot->get_port().

In reply to Greg Kroah-Hartman

From: Kuniyuki Iwashima <[email protected]>

[ Upstream commit 7a7160edf1bfde25422262fb26851cef65f695d3 ]

We assume the correct errno is -EADDRINUSE when sk->sk_prot->get_port() fails, so some ->get_port() functions return just 1 on failure and the callers return -EADDRINUSE instead.

However, mptcp_get_port() can return -EINVAL. Let's not ignore the error.

Note the only exception is inet_autobind(), all of whose callers return -EAGAIN instead.

Fixes cec37a6e41aa ("mptcp: Handle MP_CAPABLE options for outgoing connections")
---
 net/ipv4/af_inet.c              | 4 ++--
 net/ipv4/inet_connection_sock.c | 5 +++--
 net/ipv4/ping.c                 | 2 +-
 net/ipv4/udp.c                  | 2 +-
 net/ipv6/af_inet6.c             | 4 ++--
 5 files changed, 9 insertions(+), 8 deletions(-)
net/ipv4/af_inet.c +2 -2
index 7f6d7c355e38..4c8782df8eef 100644
@@ -522,9 +522,9 @@ int __inet_bind(struct sock *sk, struct sockaddr *uaddr, int addr_len,
 	/* Make sure we are allowed to bind here. */
 	if (snum || !(inet->bind_address_no_port ||
 		      (flags & BIND_FORCE_ADDRESS_NO_PORT))) {
-		if (sk->sk_prot->get_port(sk, snum)) {
+		err = sk->sk_prot->get_port(sk, snum);
+		if (err) {
 			inet->inet_saddr = inet->inet_rcv_saddr = 0;
-			err = -EADDRINUSE;
 			goto out_release_sock;
 		}
 		if (!(flags & BIND_FROM_BPF)) {
net/ipv4/inet_connection_sock.c +3 -2
index eb31c7158b39..971969cc7e17 100644
@@ -1041,7 +1041,7 @@ int inet_csk_listen_start(struct sock *sk)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct inet_sock *inet = inet_sk(sk);
-	int err = -EADDRINUSE;
+	int err;
 
 	reqsk_queue_alloc(&icsk->icsk_accept_queue);
 
@@ -1057,7 +1057,8 @@ int inet_csk_listen_start(struct sock *sk)
 	 * after validation is complete.
 	 */
 	inet_sk_state_store(sk, TCP_LISTEN);
-	if (!sk->sk_prot->get_port(sk, inet->inet_num)) {
+	err = sk->sk_prot->get_port(sk, inet->inet_num);
+	if (!err) {
 		inet->inet_sport = htons(inet->inet_num);
 
 		sk_dst_reset(sk);
net/ipv4/ping.c +1 -1
index 3b2420829c23..948f4801f993 100644
@@ -142,7 +142,7 @@ int ping_get_port(struct sock *sk, unsigned short ident)
 
 fail:
 	spin_unlock(&ping_table.lock);
-	return 1;
+	return -EADDRINUSE;
 }
 EXPORT_SYMBOL_GPL(ping_get_port);
 
net/ipv4/udp.c +1 -1
index c04a26339bd1..7fe0ba3f0933 100644
@@ -235,7 +235,7 @@ int udp_lib_get_port(struct sock *sk, unsigned short snum,
 	struct udp_table *udptable = sk->sk_prot->h.udp_table;
 	struct udp_hslot *hslot, *hslot2;
 	struct net *net = sock_net(sk);
-	int error = 1;
+	int error = -EADDRINUSE;
 
 	if (!snum) {
 		DECLARE_BITMAP(bitmap, PORTS_PER_CHAIN);
net/ipv6/af_inet6.c +2 -2
index dbb1430d6cc2..cceda5c83302 100644
@@ -403,10 +403,10 @@ static int __inet6_bind(struct sock *sk, struct sockaddr *uaddr, int addr_len,
 	/* Make sure we are allowed to bind here. */
 	if (snum || !(inet->bind_address_no_port ||
 		      (flags & BIND_FORCE_ADDRESS_NO_PORT))) {
-		if (sk->sk_prot->get_port(sk, snum)) {
+		err = sk->sk_prot->get_port(sk, snum);
+		if (err) {
 			sk->sk_ipv6only = saved_ipv6only;
 			inet_reset_saddr(sk);
-			err = -EADDRINUSE;
 			goto out;
 		}
 		if (!(flags & BIND_FROM_BPF)) {
Signature · 1 line
2.35.1
author maintainer
#350 lore raw

PATCH 351/1073 mtd: spi-nor: hide jedec_id sysfs attribute if not present

In reply to Greg Kroah-Hartman

From: Michael Walle <[email protected]>

[ Upstream commit 7d388551b6888f3725e6c957f472526b35161a5b ]

Some non-jedec compliant flashes (like the Everspin flashes) don't have an ID at all. Hide the attribute in this case.

---
 .../ABI/testing/sysfs-bus-spi-devices-spi-nor      |  3 +++
 drivers/mtd/spi-nor/sysfs.c                        | 14 ++++++++++++++
 2 files changed, 17 insertions(+)
Documentation/ABI/testing/sysfs-bus-spi-devices-spi-nor +3 -0
index d76cd3946434..e9ef69aef20b 100644
@@ -5,6 +5,9 @@ Contact:	[email protected]
 Description:	(RO) The JEDEC ID of the SPI NOR flash as reported by the
 		flash device.
 
+		The attribute is not present if the flash doesn't support
+		the "Read JEDEC ID" command (9Fh). This is the case for
+		non-JEDEC compliant flashes.
 
 What:		/sys/bus/spi/devices/.../spi-nor/manufacturer
 Date:		April 2021
drivers/mtd/spi-nor/sysfs.c +14 -0
index 9aec9d8a98ad..4c3b351aef24 100644
@@ -67,6 +67,19 @@ static struct bin_attribute *spi_nor_sysfs_bin_entries[] = {
 	NULL
 };
 
+static umode_t spi_nor_sysfs_is_visible(struct kobject *kobj,
+					struct attribute *attr, int n)
+{
+	struct spi_device *spi = to_spi_device(kobj_to_dev(kobj));
+	struct spi_mem *spimem = spi_get_drvdata(spi);
+	struct spi_nor *nor = spi_mem_get_drvdata(spimem);
+
+	if (attr == &dev_attr_jedec_id.attr && !nor->info->id_len)
+		return 0;
+
+	return 0444;
+}
+
 static umode_t spi_nor_sysfs_is_bin_visible(struct kobject *kobj,
 					    struct bin_attribute *attr, int n)
 {
@@ -82,6 +95,7 @@ static umode_t spi_nor_sysfs_is_bin_visible(struct kobject *kobj,
 
 static const struct attribute_group spi_nor_sysfs_group = {
 	.name		= "spi-nor",
+	.is_visible	= spi_nor_sysfs_is_visible,
 	.is_bin_visible	= spi_nor_sysfs_is_bin_visible,
 	.attrs		= spi_nor_sysfs_entries,
 	.bin_attrs	= spi_nor_sysfs_bin_entries,
Signature · 1 line
2.35.1
author maintainer
#351 lore raw

PATCH 352/1073 mtd: spi-nor: Fix the number of bytes for the dummy cycles

In reply to Greg Kroah-Hartman

From: Allen-KH Cheng <[email protected]>

[ Upstream commit fdc20370d93e8c6d2f448a539d08c2c064af7694 ]

The number of bytes used by spi_nor_spimem_check_readop() may be incorrect for the dummy cycles. Since nor->read_dummy is not initialized before spi_nor_spimem_adjust_hwcaps().

We use both mode and wait state clock cycles instead of nor->read_dummy.

---
 drivers/mtd/spi-nor/core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/mtd/spi-nor/core.c +2 -1
index bee8fc4c9f07..0cf1a1797ea3 100644
@@ -1914,7 +1914,8 @@ static int spi_nor_spimem_check_readop(struct spi_nor *nor,
 	spi_nor_spimem_setup_op(nor, &op, read->proto);
 
 	/* convert the dummy cycles to the number of bytes */
-	op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+	op.dummy.nbytes = (read->num_mode_clocks + read->num_wait_states) *
+			  op.dummy.buswidth / 8;
 	if (spi_nor_protocol_is_dtr(nor->read_proto))
 		op.dummy.nbytes *= 2;
 
Signature · 1 line
2.35.1
author maintainer
#352 lore raw

PATCH 353/1073 clk: imx93: correct the flexspi1 clock setting

In reply to Greg Kroah-Hartman

From: Haibo Chen <[email protected]>

[ Upstream commit 62dfdbcc16e767b91ed35d4fc0428c86d4688505 ]

Correct IMX93_CLK_FLEXSPI1_GATE CCGR setting. Otherwise the flexspi always can't be assigned to a parent clock when dump the clock tree.

---
 drivers/clk/imx/clk-imx93.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/imx/clk-imx93.c +1 -1
index dcc41d178238..4d2524addc3e 100644
@@ -162,7 +162,7 @@ static const struct imx93_clk_ccgr {
 	{ IMX93_CLK_MU_B_GATE,		"mu_b",		"bus_aon_root",		0x8500, },
 	{ IMX93_CLK_EDMA1_GATE,		"edma1",	"m33_root",		0x8540, },
 	{ IMX93_CLK_EDMA2_GATE,		"edma2",	"wakeup_axi_root",	0x8580, },
-	{ IMX93_CLK_FLEXSPI1_GATE,	"flexspi",	"flexspi_root",		0x8640, },
+	{ IMX93_CLK_FLEXSPI1_GATE,	"flexspi1",	"flexspi1_root",	0x8640, },
 	{ IMX93_CLK_GPIO1_GATE,		"gpio1",	"m33_root",		0x8880, },
 	{ IMX93_CLK_GPIO2_GATE,		"gpio2",	"bus_wakeup_root",	0x88c0, },
 	{ IMX93_CLK_GPIO3_GATE,		"gpio3",	"bus_wakeup_root",	0x8900, },
Signature · 1 line
2.35.1
author maintainer
#353 lore raw

PATCH 354/1073 HID: i2c: let RMI devices decide what constitutes wakeup event

In reply to Greg Kroah-Hartman

From: Dmitry Torokhov <[email protected]>

[ Upstream commit 9984fbf55b9bd998b4ff66395cbb118020c1effa ]

HID-RMI is special in the sense that it does not carry HID events directly, but rather uses HID protocol as a wrapper/transport for RMI protocol. Therefore we should not assume that all data coming from the device via interrupt is associated with user activity and report wakeup event indiscriminately, but rather let HID-RMI do that when appropriate.

HID-RMI devices tag responses to the commands issued by the host as RMI_READ_DATA_REPORT_ID whereas motion and other input events from the device are tagged as RMI_ATTN_REPORT_ID. Change hid-rmi to report wakeup events when receiving the latter packets. This allows ChromeOS to accurately identify wakeup source and make correct decision on the mode of the resume the system should take ("dark" where the display stays off vs normal one).

Fixes d951ae1ce803 ("HID: i2c-hid: Report wakeup events")
---
 drivers/hid/hid-rmi.c              | 2 ++
 drivers/hid/i2c-hid/i2c-hid-core.c | 3 ++-
 2 files changed, 4 insertions(+), 1 deletion(-)
drivers/hid/hid-rmi.c +2 -0
index 311eee599ce9..b2bf588d18c3 100644
@@ -327,6 +327,8 @@ static int rmi_input_event(struct hid_device *hdev, u8 *data, int size)
 	if (!(test_bit(RMI_STARTED, &hdata->flags)))
 		return 0;
 
+	pm_wakeup_event(hdev->dev.parent, 0);
+
 	local_irq_save(flags);
 
 	rmi_set_attn_data(rmi_dev, data[1], &data[2], size - 2);
drivers/hid/i2c-hid/i2c-hid-core.c +2 -1
index c078f09a2318..5a365648206e 100644
@@ -554,7 +554,8 @@ static void i2c_hid_get_input(struct i2c_hid *ihid)
 	i2c_hid_dbg(ihid, "input: %*ph\n", ret_size, ihid->inbuf);
 
 	if (test_bit(I2C_HID_STARTED, &ihid->flags)) {
-		pm_wakeup_event(&ihid->client->dev, 0);
+		if (ihid->hid->group != HID_GROUP_RMI)
+			pm_wakeup_event(&ihid->client->dev, 0);
 
 		hid_input_report(ihid->hid, HID_INPUT_REPORT,
 				ihid->inbuf + sizeof(__le16),
Signature · 1 line
2.35.1
author maintainer
#354 lore raw

PATCH 355/1073 clk: imx93: unmap anatop base in error handling path

In reply to Greg Kroah-Hartman

From: Peng Fan <[email protected]>

[ Upstream commit bda7b7f396f94d8df89ecacc88f2826908e8762c ]

The anatop base is not unmapped during error handling path, fix it.

---
 drivers/clk/imx/clk-imx93.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/clk/imx/clk-imx93.c +9 -6
index 4d2524addc3e..8d67b065f7b6 100644
@@ -247,7 +247,7 @@ static int imx93_clocks_probe(struct platform_device *pdev)
 	struct device_node *np = dev->of_node;
 	const struct imx93_clk_root *root;
 	const struct imx93_clk_ccgr *ccgr;
-	void __iomem *base = NULL;
+	void __iomem *base, *anatop_base;
 	int i, ret;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
@@ -274,20 +274,22 @@ static int imx93_clocks_probe(struct platform_device *pdev)
 								    "sys_pll_pfd2", 1, 2);
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx93-anatop");
-	base = of_iomap(np, 0);
+	anatop_base = of_iomap(np, 0);
 	of_node_put(np);
-	if (WARN_ON(!base))
+	if (WARN_ON(!anatop_base))
 		return -ENOMEM;
 
-	clks[IMX93_CLK_AUDIO_PLL] = imx_clk_fracn_gppll("audio_pll", "osc_24m", base + 0x1200,
+	clks[IMX93_CLK_AUDIO_PLL] = imx_clk_fracn_gppll("audio_pll", "osc_24m", anatop_base + 0x1200,
 							&imx_fracn_gppll);
-	clks[IMX93_CLK_VIDEO_PLL] = imx_clk_fracn_gppll("video_pll", "osc_24m", base + 0x1400,
+	clks[IMX93_CLK_VIDEO_PLL] = imx_clk_fracn_gppll("video_pll", "osc_24m", anatop_base + 0x1400,
 							&imx_fracn_gppll);
 
 	np = dev->of_node;
 	base = devm_platform_ioremap_resource(pdev, 0);
-	if (WARN_ON(IS_ERR(base)))
+	if (WARN_ON(IS_ERR(base))) {
+		iounmap(anatop_base);
 		return PTR_ERR(base);
+	}
 
 	for (i = 0; i < ARRAY_SIZE(root_array); i++) {
 		root = &root_array[i];
@@ -317,6 +319,7 @@ static int imx93_clocks_probe(struct platform_device *pdev)
 
 unregister_hws:
 	imx_unregister_hw_clocks(clks, IMX93_CLK_END);
+	iounmap(anatop_base);
 
 	return ret;
 }
Signature · 1 line
2.35.1
author maintainer
#355 lore raw

PATCH 356/1073 clk: imx93: correct enet clock

In reply to Greg Kroah-Hartman

From: Peng Fan <[email protected]>

[ Upstream commit 4be5d91b9433f1dc76de485e240ca6aaa2d19f65 ]

Per update Reference Mannual, correct the enet clock parent to wakeup_axi_root.

---
 drivers/clk/imx/clk-imx93.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/imx/clk-imx93.c +1 -1
index 8d67b065f7b6..2e99c3443d3c 100644
@@ -229,7 +229,7 @@ static const struct imx93_clk_ccgr {
 	{ IMX93_CLK_AUD_XCVR_GATE,	"aud_xcvr",	"audio_xcvr_root",	0x9b80, },
 	{ IMX93_CLK_SPDIF_GATE,		"spdif",	"spdif_root",		0x9c00, },
 	{ IMX93_CLK_HSIO_32K_GATE,	"hsio_32k",	"osc_32k",		0x9dc0, },
-	{ IMX93_CLK_ENET1_GATE,		"enet1",	"enet_root",		0x9e00, },
+	{ IMX93_CLK_ENET1_GATE,		"enet1",	"wakeup_axi_root",	0x9e00, },
 	{ IMX93_CLK_ENET_QOS_GATE,	"enet_qos",	"wakeup_axi_root",	0x9e40, },
 	{ IMX93_CLK_SYS_CNT_GATE,	"sys_cnt",	"osc_24m",		0x9e80, },
 	{ IMX93_CLK_TSTMR1_GATE,	"tstmr1",	"bus_aon_root",		0x9ec0, },
Signature · 1 line
2.35.1
author maintainer
#356 lore raw

PATCH 357/1073 bpf: Move skb->len == 0 checks into __bpf_redirect

In reply to Greg Kroah-Hartman

From: Stanislav Fomichev <[email protected]>

[ Upstream commit 114039b342014680911c35bd6b72624180fd669a ]

To avoid potentially breaking existing users.

Both mac/no-mac cases have to be amended; mac_header >= network_header is not enough (verified with a new test, see next patch).

Fixes fd1894224407 ("bpf: Don't redirect packets with invalid pkt_len")
---
 net/bpf/test_run.c | 3 ---
 net/core/filter.c  | 7 ++++++-
 2 files changed, 6 insertions(+), 4 deletions(-)
net/bpf/test_run.c +0 -3
index b422238f9f86..5d53332ea3c9 100644
@@ -939,9 +939,6 @@ static int convert___skb_to_skb(struct sk_buff *skb, struct __sk_buff *__skb)
 {
 	struct qdisc_skb_cb *cb = (struct qdisc_skb_cb *)skb->cb;
 
-	if (!skb->len)
-		return -EINVAL;
-
 	if (!__skb)
 		return 0;
 
net/core/filter.c +6 -1
index c191db80ce93..5ac3ecc2edb8 100644
@@ -2123,6 +2123,11 @@ static int __bpf_redirect_no_mac(struct sk_buff *skb, struct net_device *dev,
 {
 	unsigned int mlen = skb_network_offset(skb);
 
+	if (unlikely(skb->len <= mlen)) {
+		kfree_skb(skb);
+		return -ERANGE;
+	}
+
 	if (mlen) {
 		__skb_pull(skb, mlen);
 
@@ -2144,7 +2149,7 @@ static int __bpf_redirect_common(struct sk_buff *skb, struct net_device *dev,
 				 u32 flags)
 {
 	/* Verify that a link layer header is carried */
-	if (unlikely(skb->mac_header >= skb->network_header)) {
+	if (unlikely(skb->mac_header >= skb->network_header || skb->len == 0)) {
 		kfree_skb(skb);
 		return -ERANGE;
 	}
Signature · 1 line
2.35.1
author maintainer
#357 lore raw

PATCH 358/1073 HID: hid-sensor-custom: set fixed size for custom attributes

In reply to Greg Kroah-Hartman

From: Marcus Folkesson <[email protected]>

[ Upstream commit 9d013910df22de91333a0acc81d1dbb115bd76f6 ]

This is no bugfix (so no Fixes: tag is necessary) as it is taken care of in hid_sensor_custom_add_attributes().

The motivation for this patch is that:
hid_sensor_custom_field.attr_name and hid_sensor_custom_field.attrs
has the size of HID_CUSTOM_TOTAL_ATTRS and used in same context.

We compare against HID_CUSTOM_TOTAL_ATTRS when
looping through hid_custom_attrs.

We will silent the smatch error:
hid_sensor_custom_add_attributes() error: buffer overflow 'hid_custom_attrs' 8 <= 10

---
 drivers/hid/hid-sensor-custom.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/hid/hid-sensor-custom.c +1 -1
index 32c2306e240d..602465ad2745 100644
@@ -62,7 +62,7 @@ struct hid_sensor_sample {
 	u32 raw_len;
 } __packed;
 
-static struct attribute hid_custom_attrs[] = {
+static struct attribute hid_custom_attrs[HID_CUSTOM_TOTAL_ATTRS] = {
 	{.name = "name", .mode = S_IRUGO},
 	{.name = "units", .mode = S_IRUGO},
 	{.name = "unit-expo", .mode = S_IRUGO},
Signature · 1 line
2.35.1
author maintainer
#358 lore raw

PATCH 359/1073 clk: imx: imxrt1050: fix IMXRT1050_CLK_LCDIF_APB offsets

In reply to Greg Kroah-Hartman

From: Giulio Benetti <[email protected]>

[ Upstream commit 3095c02f95e537c553e0b30948c2f6c7cbed87ee ]

Fix IMXRT1050_CLK_LCDIF_APB offsets.

Fixes 7154b046d8f3 ("clk: imx: Add initial support for i.MXRT1050 clock driver")
Cc Jesse Taube <[email protected]>
---
 drivers/clk/imx/clk-imxrt1050.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/imx/clk-imxrt1050.c +1 -1
index 9539d35588ee..26108e9f7e67 100644
@@ -140,7 +140,7 @@ static int imxrt1050_clocks_probe(struct platform_device *pdev)
 	hws[IMXRT1050_CLK_USDHC1] = imx_clk_hw_gate2("usdhc1", "usdhc1_podf", ccm_base + 0x80, 2);
 	hws[IMXRT1050_CLK_USDHC2] = imx_clk_hw_gate2("usdhc2", "usdhc2_podf", ccm_base + 0x80, 4);
 	hws[IMXRT1050_CLK_LPUART1] = imx_clk_hw_gate2("lpuart1", "lpuart_podf", ccm_base + 0x7c, 24);
-	hws[IMXRT1050_CLK_LCDIF_APB] = imx_clk_hw_gate2("lcdif", "lcdif_podf", ccm_base + 0x74, 10);
+	hws[IMXRT1050_CLK_LCDIF_APB] = imx_clk_hw_gate2("lcdif", "lcdif_podf", ccm_base + 0x70, 28);
 	hws[IMXRT1050_CLK_DMA] = imx_clk_hw_gate("dma", "ipg", ccm_base + 0x7C, 6);
 	hws[IMXRT1050_CLK_DMA_MUX] = imx_clk_hw_gate("dmamux0", "ipg", ccm_base + 0x7C, 7);
 	imx_check_clk_hws(hws, IMXRT1050_CLK_END);
Signature · 1 line
2.35.1
author maintainer
#359 lore raw

PATCH 360/1073 pinctrl: k210: call of_node_put()

In reply to Greg Kroah-Hartman

From: ZhangPeng <[email protected]>

[ Upstream commit a8acc11643082a706de86a19f1f824712d971984 ]

Since for_each_available_child_of_node() will increase the refcount of node, we need to call of_node_put() manually when breaking out of the iteration.

Fixes d4c34d09ab03 ("pinctrl: Add RISC-V Canaan Kendryte K210 FPIOA driver")
---
 drivers/pinctrl/pinctrl-k210.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/pinctrl/pinctrl-k210.c +3 -1
index ecab6bf63dc6..ad4db99094a7 100644
@@ -862,8 +862,10 @@ static int k210_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
 	for_each_available_child_of_node(np_config, np) {
 		ret = k210_pinctrl_dt_subnode_to_map(pctldev, np, map,
 						     &reserved_maps, num_maps);
-		if (ret < 0)
+		if (ret < 0) {
+			of_node_put(np);
 			goto err;
+		}
 	}
 	return 0;
 
Signature · 1 line
2.35.1
author maintainer
#360 lore raw

PATCH 361/1073 wifi: rtw89: fix physts IE page check

In reply to Greg Kroah-Hartman

From: Zong-Zhe Yang <[email protected]>

[ Upstream commit 9e2f177de1bfb7d891bf38140bda54831ecef30d ]

The index RTW89_PHYSTS_BITMAP_NUM is not a valid physts IE page. So, fix the check condition.

Fixes eb4e52b3f38d ("rtw89: fix incorrect channel info during scan")
---
 drivers/net/wireless/realtek/rtw89/phy.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/realtek/rtw89/phy.c +1 -1
index 1532c0a6bbc4..2925179f508c 100644
@@ -3045,7 +3045,7 @@ void rtw89_phy_env_monitor_track(struct rtw89_dev *rtwdev)
 
 static bool rtw89_physts_ie_page_valid(enum rtw89_phy_status_bitmap *ie_page)
 {
-	if (*ie_page > RTW89_PHYSTS_BITMAP_NUM ||
+	if (*ie_page >= RTW89_PHYSTS_BITMAP_NUM ||
 	    *ie_page == RTW89_RSVD_9)
 		return false;
 	else if (*ie_page > RTW89_RSVD_9)
Signature · 1 line
2.35.1
author maintainer
#361 lore raw

PATCH 362/1073 ASoC: Intel: avs: Lock substream before snd_pcm_stop()

In reply to Greg Kroah-Hartman

From: Cezary Rojewski <[email protected]>

[ Upstream commit c30c8f9d51ec24b36e2c65a6307a5c8cbc5a0ebc ]

snd_pcm_stop() shall be called with stream lock held to prevent any races between nonatomic streaming operations.

Fixes 2f1f570cd730 ("ASoC: Intel: avs: Coredump and recovery flow")
---
 sound/soc/intel/avs/ipc.c | 3 +++
 1 file changed, 3 insertions(+)
sound/soc/intel/avs/ipc.c +3 -0
index 77da206f7dbb..306f0dc4eaf5 100644
@@ -123,7 +123,10 @@ static void avs_dsp_recovery(struct avs_dev *adev)
 				if (!substream || !substream->runtime)
 					continue;
 
+				/* No need for _irq() as we are in nonatomic context. */
+				snd_pcm_stream_lock(substream);
 				snd_pcm_stop(substream, SNDRV_PCM_STATE_DISCONNECTED);
+				snd_pcm_stream_unlock(substream);
 			}
 		}
 	}
Signature · 1 line
2.35.1
author maintainer
#362 lore raw

PATCH 363/1073 ALSA: pcm: fix undefined behavior in bit shift for SNDRV_PCM_RATE_KNOT

In reply to Greg Kroah-Hartman

From: Baisong Zhong <[email protected]>

[ Upstream commit b5172e62458f8e6ff359e5f096044a488db90ac5 ]

Shifting signed 32-bit value by 31 bits is undefined, so changing significant bit to unsigned. The UBSAN warning calltrace like below:

UBSAN: shift-out-of-bounds in sound/core/pcm_native.c:2676:21
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
 <TASK>
 dump_stack_lvl+0x8d/0xcf
 ubsan_epilogue+0xa/0x44
 __ubsan_handle_shift_out_of_bounds+0x1e7/0x208
 snd_pcm_open_substream+0x9f0/0xa90
 snd_pcm_oss_open.part.26+0x313/0x670
 snd_pcm_oss_open+0x30/0x40
 soundcore_open+0x18b/0x2e0
 chrdev_open+0xe2/0x270
 do_dentry_open+0x2f7/0x620
 path_openat+0xd66/0xe70
 do_filp_open+0xe3/0x170
 do_sys_openat2+0x357/0x4a0
 do_sys_open+0x87/0xd0
 do_syscall_64+0x34/0x80
---
 include/sound/pcm.h | 36 ++++++++++++++++++------------------
 1 file changed, 18 insertions(+), 18 deletions(-)
include/sound/pcm.h +18 -18
index 8c48a5bce88c..25695f5f795a 100644
@@ -106,24 +106,24 @@ struct snd_pcm_ops {
 #define SNDRV_PCM_POS_XRUN		((snd_pcm_uframes_t)-1)
 
 /* If you change this don't forget to change rates[] table in pcm_native.c */
-#define SNDRV_PCM_RATE_5512		(1<<0)		/* 5512Hz */
-#define SNDRV_PCM_RATE_8000		(1<<1)		/* 8000Hz */
-#define SNDRV_PCM_RATE_11025		(1<<2)		/* 11025Hz */
-#define SNDRV_PCM_RATE_16000		(1<<3)		/* 16000Hz */
-#define SNDRV_PCM_RATE_22050		(1<<4)		/* 22050Hz */
-#define SNDRV_PCM_RATE_32000		(1<<5)		/* 32000Hz */
-#define SNDRV_PCM_RATE_44100		(1<<6)		/* 44100Hz */
-#define SNDRV_PCM_RATE_48000		(1<<7)		/* 48000Hz */
-#define SNDRV_PCM_RATE_64000		(1<<8)		/* 64000Hz */
-#define SNDRV_PCM_RATE_88200		(1<<9)		/* 88200Hz */
-#define SNDRV_PCM_RATE_96000		(1<<10)		/* 96000Hz */
-#define SNDRV_PCM_RATE_176400		(1<<11)		/* 176400Hz */
-#define SNDRV_PCM_RATE_192000		(1<<12)		/* 192000Hz */
-#define SNDRV_PCM_RATE_352800		(1<<13)		/* 352800Hz */
-#define SNDRV_PCM_RATE_384000		(1<<14)		/* 384000Hz */
-
-#define SNDRV_PCM_RATE_CONTINUOUS	(1<<30)		/* continuous range */
-#define SNDRV_PCM_RATE_KNOT		(1<<31)		/* supports more non-continuos rates */
+#define SNDRV_PCM_RATE_5512		(1U<<0)		/* 5512Hz */
+#define SNDRV_PCM_RATE_8000		(1U<<1)		/* 8000Hz */
+#define SNDRV_PCM_RATE_11025		(1U<<2)		/* 11025Hz */
+#define SNDRV_PCM_RATE_16000		(1U<<3)		/* 16000Hz */
+#define SNDRV_PCM_RATE_22050		(1U<<4)		/* 22050Hz */
+#define SNDRV_PCM_RATE_32000		(1U<<5)		/* 32000Hz */
+#define SNDRV_PCM_RATE_44100		(1U<<6)		/* 44100Hz */
+#define SNDRV_PCM_RATE_48000		(1U<<7)		/* 48000Hz */
+#define SNDRV_PCM_RATE_64000		(1U<<8)		/* 64000Hz */
+#define SNDRV_PCM_RATE_88200		(1U<<9)		/* 88200Hz */
+#define SNDRV_PCM_RATE_96000		(1U<<10)	/* 96000Hz */
+#define SNDRV_PCM_RATE_176400		(1U<<11)	/* 176400Hz */
+#define SNDRV_PCM_RATE_192000		(1U<<12)	/* 192000Hz */
+#define SNDRV_PCM_RATE_352800		(1U<<13)	/* 352800Hz */
+#define SNDRV_PCM_RATE_384000		(1U<<14)	/* 384000Hz */
+
+#define SNDRV_PCM_RATE_CONTINUOUS	(1U<<30)	/* continuous range */
+#define SNDRV_PCM_RATE_KNOT		(1U<<31)	/* supports more non-continuos rates */
 
 #define SNDRV_PCM_RATE_8000_44100	(SNDRV_PCM_RATE_8000|SNDRV_PCM_RATE_11025|\
 					 SNDRV_PCM_RATE_16000|SNDRV_PCM_RATE_22050|\
Signature · 1 line
2.35.1
author maintainer
#363 lore raw

PATCH 364/1073 ALSA: seq: fix undefined behavior in bit shift for SNDRV_SEQ_FILTER_USE_EVENT

In reply to Greg Kroah-Hartman

From: Baisong Zhong <[email protected]>

[ Upstream commit cf59e1e4c79bf741905484cdb13c130b53576a16 ]

Shifting signed 32-bit value by 31 bits is undefined, so changing significant bit to unsigned. The UBSAN warning calltrace like below:

UBSAN: shift-out-of-bounds in sound/core/seq/seq_clientmgr.c:509:22
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
 <TASK>
 dump_stack_lvl+0x8d/0xcf
 ubsan_epilogue+0xa/0x44
 __ubsan_handle_shift_out_of_bounds+0x1e7/0x208
 snd_seq_deliver_single_event.constprop.21+0x191/0x2f0
 snd_seq_deliver_event+0x1a2/0x350
 snd_seq_kernel_client_dispatch+0x8b/0xb0
 snd_seq_client_notify_subscription+0x72/0xa0
 snd_seq_ioctl_subscribe_port+0x128/0x160
 snd_seq_kernel_client_ctl+0xce/0xf0
 snd_seq_oss_create_client+0x109/0x15b
 alsa_seq_oss_init+0x11c/0x1aa
 do_one_initcall+0x80/0x440
 kernel_init_freeable+0x370/0x3c3
 kernel_init+0x1b/0x190
 ret_from_fork+0x1f/0x30
 </TASK>
---
 include/uapi/sound/asequencer.h | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
include/uapi/sound/asequencer.h +4 -4
index a75e14edc957..dbd60f48b4b0 100644
@@ -344,10 +344,10 @@ typedef int __bitwise snd_seq_client_type_t;
 #define	KERNEL_CLIENT	((__force snd_seq_client_type_t) 2)
                         
 	/* event filter flags */
-#define SNDRV_SEQ_FILTER_BROADCAST	(1<<0)	/* accept broadcast messages */
-#define SNDRV_SEQ_FILTER_MULTICAST	(1<<1)	/* accept multicast messages */
-#define SNDRV_SEQ_FILTER_BOUNCE		(1<<2)	/* accept bounce event in error */
-#define SNDRV_SEQ_FILTER_USE_EVENT	(1<<31)	/* use event filter */
+#define SNDRV_SEQ_FILTER_BROADCAST	(1U<<0)	/* accept broadcast messages */
+#define SNDRV_SEQ_FILTER_MULTICAST	(1U<<1)	/* accept multicast messages */
+#define SNDRV_SEQ_FILTER_BOUNCE		(1U<<2)	/* accept bounce event in error */
+#define SNDRV_SEQ_FILTER_USE_EVENT	(1U<<31)	/* use event filter */
 
 struct snd_seq_client_info {
 	int client;			/* client number to inquire */
Signature · 1 line
2.35.1
author maintainer
#364 lore raw

PATCH 365/1073 regulator: core: use kfree_const() to free space conditionally

In reply to Greg Kroah-Hartman

From: Wang ShaoBo <[email protected]>

[ Upstream commit dc8d006d15b623c1d80b90b45d6dcb6e890dad09 ]

Use kfree_const() to free supply_name conditionally in create_regulator() as supply_name may be allocated from kmalloc() or directly from .rodata section.

Fixes 87fe29b61f95 ("regulator: push allocations in create_regulator() outside of lock")
---
 drivers/regulator/core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/regulator/core.c +1 -1
index afd17b13de7c..b7e7eec1084e 100644
@@ -1795,7 +1795,7 @@ static struct regulator *create_regulator(struct regulator_dev *rdev,
 
 	regulator = kzalloc(sizeof(*regulator), GFP_KERNEL);
 	if (regulator == NULL) {
-		kfree(supply_name);
+		kfree_const(supply_name);
 		return NULL;
 	}
 
Signature · 1 line
2.35.1
author maintainer
#365 lore raw

PATCH 366/1073 clk: rockchip: Fix memory leak in rockchip_clk_register_pll()

In reply to Greg Kroah-Hartman

From: Xiu Jianfeng <[email protected]>

[ Upstream commit 739a6a6bbdb793bd57938cb24aa5a6df89983546 ]

If clk_register() fails, @pll->rate_table may have allocated memory by kmemdup(), so it needs to be freed, otherwise will cause memory leak issue, this patch fixes it.

Fixes 90c590254051 ("clk: rockchip: add clock type for pll clocks and pll used on rk3066")
---
 drivers/clk/rockchip/clk-pll.c | 1 +
 1 file changed, 1 insertion(+)
drivers/clk/rockchip/clk-pll.c +1 -0
index f7827b3b7fc1..6e5e502be44a 100644
@@ -981,6 +981,7 @@ struct clk *rockchip_clk_register_pll(struct rockchip_clk_provider *ctx,
 	return mux_clk;
 
 err_pll:
+	kfree(pll->rate_table);
 	clk_unregister(mux_clk);
 	mux_clk = pll_clk;
 err_mux:
Signature · 1 line
2.35.1
author maintainer
#366 lore raw

PATCH 367/1073 drm/amdgpu: fix pci device refcount leak

In reply to Greg Kroah-Hartman

From: Yang Yingliang <[email protected]>

[ Upstream commit b85e285e3d6352b02947fc1b72303673dfacb0aa ]

As comment of pci_get_domain_bus_and_slot() says, it returns a pci device with refcount increment, when finish using it, the caller must decrement the reference count by calling pci_dev_put().

So before returning from amdgpu_device_resume|suspend_display_audio(), pci_dev_put() is called to avoid refcount leak.

Fixes 3f12acc8d6d4 ("drm/amdgpu: put the audio codec into suspend state before gpu reset V3")
---
 drivers/gpu/drm/amd/amdgpu/amdgpu_device.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c +4 -0
index e0c960cc1d2e..f04e698e631c 100644
@@ -5004,6 +5004,8 @@ static void amdgpu_device_resume_display_audio(struct amdgpu_device *adev)
 		pm_runtime_enable(&(p->dev));
 		pm_runtime_resume(&(p->dev));
 	}
+
+	pci_dev_put(p);
 }
 
 static int amdgpu_device_suspend_display_audio(struct amdgpu_device *adev)
@@ -5042,6 +5044,7 @@ static int amdgpu_device_suspend_display_audio(struct amdgpu_device *adev)
 
 		if (expires < ktime_get_mono_fast_ns()) {
 			dev_warn(adev->dev, "failed to suspend display audio\n");
+			pci_dev_put(p);
 			/* TODO: abort the succeeding gpu reset? */
 			return -ETIMEDOUT;
 		}
@@ -5049,6 +5052,7 @@ static int amdgpu_device_suspend_display_audio(struct amdgpu_device *adev)
 
 	pm_runtime_disable(&(p->dev));
 
+	pci_dev_put(p);
 	return 0;
 }
 
Signature · 1 line
2.35.1
author maintainer
#367 lore raw

PATCH 368/1073 drm/i915/guc: make default_lists const data

In reply to Greg Kroah-Hartman

From: Jani Nikula <[email protected]>

[ Upstream commit dfa5e6ef3ccefff9fa8a70d9f5fa6ef6244aa312 ]

The default_lists array should be in rodata.

Fixes dce2bd542337 ("drm/i915/guc: Add Gen9 registers for GuC error state capture.")
Cc Alan Previn <[email protected]>
Cc Umesh Nerlige Ramappa <[email protected]>
Cc Lucas De Marchi <[email protected]>
(cherry picked from commit 8b7f7a9b10b704ba7d73199ff0f01354e0bad7a5)
---
 drivers/gpu/drm/i915/gt/uc/intel_guc_capture.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/gt/uc/intel_guc_capture.c +1 -1
index 34e72675b7e4..4c51888fd78b 100644
@@ -165,7 +165,7 @@ static const struct __guc_mmio_reg_descr empty_regs_list[] = {
 	}
 
 /* List of lists */
-static struct __guc_mmio_reg_descr_group default_lists[] = {
+static const struct __guc_mmio_reg_descr_group default_lists[] = {
 	MAKE_REGLIST(default_global_regs, PF, GLOBAL, 0),
 	MAKE_REGLIST(default_rc_class_regs, PF, ENGINE_CLASS, GUC_RENDER_CLASS),
 	MAKE_REGLIST(xe_lpd_rc_inst_regs, PF, ENGINE_INSTANCE, GUC_RENDER_CLASS),
Signature · 1 line
2.35.1
author maintainer
#368 lore raw

PATCH 369/1073 selftests/bpf: Make sure zero-len skbs arent redirectable

In reply to Greg Kroah-Hartman

From: Stanislav Fomichev <[email protected]>

[ Upstream commit 68f8e3d4b916531ea3bb8b83e35138cf78f2fce5 ]

LWT_XMIT to test L3 case, TC to test L2 case.

v2:
- s/veth_ifindex/ipip_ifindex/ in two places (Martin)
- add comment about which condition triggers the rejection (Martin)

Stable-dep-of: 8ac88eece800 ("selftests/bpf: Mount debugfs in setns_by_fd")

---
 .../selftests/bpf/prog_tests/empty_skb.c      | 146 ++++++++++++++++++
 tools/testing/selftests/bpf/progs/empty_skb.c |  37 +++++
 2 files changed, 183 insertions(+)
 create mode 100644 tools/testing/selftests/bpf/prog_tests/empty_skb.c
 create mode 100644 tools/testing/selftests/bpf/progs/empty_skb.c
tools/testing/selftests/bpf/prog_tests/empty_skb.c new file +146 -0
new file mode 100644
index 000000000000..32dd731e9070
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <test_progs.h>
+#include <network_helpers.h>
+#include <net/if.h>
+#include "empty_skb.skel.h"
+
+#define SYS(cmd) ({ \
+	if (!ASSERT_OK(system(cmd), (cmd))) \
+		goto out; \
+})
+
+void test_empty_skb(void)
+{
+	LIBBPF_OPTS(bpf_test_run_opts, tattr);
+	struct empty_skb *bpf_obj = NULL;
+	struct nstoken *tok = NULL;
+	struct bpf_program *prog;
+	char eth_hlen_pp[15];
+	char eth_hlen[14];
+	int veth_ifindex;
+	int ipip_ifindex;
+	int err;
+	int i;
+
+	struct {
+		const char *msg;
+		const void *data_in;
+		__u32 data_size_in;
+		int *ifindex;
+		int err;
+		int ret;
+		bool success_on_tc;
+	} tests[] = {
+		/* Empty packets are always rejected. */
+
+		{
+			/* BPF_PROG_RUN ETH_HLEN size check */
+			.msg = "veth empty ingress packet",
+			.data_in = NULL,
+			.data_size_in = 0,
+			.ifindex = &veth_ifindex,
+			.err = -EINVAL,
+		},
+		{
+			/* BPF_PROG_RUN ETH_HLEN size check */
+			.msg = "ipip empty ingress packet",
+			.data_in = NULL,
+			.data_size_in = 0,
+			.ifindex = &ipip_ifindex,
+			.err = -EINVAL,
+		},
+
+		/* ETH_HLEN-sized packets:
+		 * - can not be redirected at LWT_XMIT
+		 * - can be redirected at TC to non-tunneling dest
+		 */
+
+		{
+			/* __bpf_redirect_common */
+			.msg = "veth ETH_HLEN packet ingress",
+			.data_in = eth_hlen,
+			.data_size_in = sizeof(eth_hlen),
+			.ifindex = &veth_ifindex,
+			.ret = -ERANGE,
+			.success_on_tc = true,
+		},
+		{
+			/* __bpf_redirect_no_mac
+			 *
+			 * lwt: skb->len=0 <= skb_network_offset=0
+			 * tc: skb->len=14 <= skb_network_offset=14
+			 */
+			.msg = "ipip ETH_HLEN packet ingress",
+			.data_in = eth_hlen,
+			.data_size_in = sizeof(eth_hlen),
+			.ifindex = &ipip_ifindex,
+			.ret = -ERANGE,
+		},
+
+		/* ETH_HLEN+1-sized packet should be redirected. */
+
+		{
+			.msg = "veth ETH_HLEN+1 packet ingress",
+			.data_in = eth_hlen_pp,
+			.data_size_in = sizeof(eth_hlen_pp),
+			.ifindex = &veth_ifindex,
+		},
+		{
+			.msg = "ipip ETH_HLEN+1 packet ingress",
+			.data_in = eth_hlen_pp,
+			.data_size_in = sizeof(eth_hlen_pp),
+			.ifindex = &ipip_ifindex,
+		},
+	};
+
+	SYS("ip netns add empty_skb");
+	tok = open_netns("empty_skb");
+	SYS("ip link add veth0 type veth peer veth1");
+	SYS("ip link set dev veth0 up");
+	SYS("ip link set dev veth1 up");
+	SYS("ip addr add 10.0.0.1/8 dev veth0");
+	SYS("ip addr add 10.0.0.2/8 dev veth1");
+	veth_ifindex = if_nametoindex("veth0");
+
+	SYS("ip link add ipip0 type ipip local 10.0.0.1 remote 10.0.0.2");
+	SYS("ip link set ipip0 up");
+	SYS("ip addr add 192.168.1.1/16 dev ipip0");
+	ipip_ifindex = if_nametoindex("ipip0");
+
+	bpf_obj = empty_skb__open_and_load();
+	if (!ASSERT_OK_PTR(bpf_obj, "open skeleton"))
+		goto out;
+
+	for (i = 0; i < ARRAY_SIZE(tests); i++) {
+		bpf_object__for_each_program(prog, bpf_obj->obj) {
+			char buf[128];
+			bool at_tc = !strncmp(bpf_program__section_name(prog), "tc", 2);
+
+			tattr.data_in = tests[i].data_in;
+			tattr.data_size_in = tests[i].data_size_in;
+
+			tattr.data_size_out = 0;
+			bpf_obj->bss->ifindex = *tests[i].ifindex;
+			bpf_obj->bss->ret = 0;
+			err = bpf_prog_test_run_opts(bpf_program__fd(prog), &tattr);
+			sprintf(buf, "err: %s [%s]", tests[i].msg, bpf_program__name(prog));
+
+			if (at_tc && tests[i].success_on_tc)
+				ASSERT_GE(err, 0, buf);
+			else
+				ASSERT_EQ(err, tests[i].err, buf);
+			sprintf(buf, "ret: %s [%s]", tests[i].msg, bpf_program__name(prog));
+			if (at_tc && tests[i].success_on_tc)
+				ASSERT_GE(bpf_obj->bss->ret, 0, buf);
+			else
+				ASSERT_EQ(bpf_obj->bss->ret, tests[i].ret, buf);
+		}
+	}
+
+out:
+	if (bpf_obj)
+		empty_skb__destroy(bpf_obj);
+	if (tok)
+		close_netns(tok);
+	system("ip netns del empty_skb");
+}
tools/testing/selftests/bpf/progs/empty_skb.c new file +37 -0
new file mode 100644
index 000000000000..4b0cd6753251
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+#include <linux/bpf.h>
+#include <bpf/bpf_helpers.h>
+#include <bpf/bpf_endian.h>
+
+char _license[] SEC("license") = "GPL";
+
+int ifindex;
+int ret;
+
+SEC("lwt_xmit")
+int redirect_ingress(struct __sk_buff *skb)
+{
+	ret = bpf_clone_redirect(skb, ifindex, BPF_F_INGRESS);
+	return 0;
+}
+
+SEC("lwt_xmit")
+int redirect_egress(struct __sk_buff *skb)
+{
+	ret = bpf_clone_redirect(skb, ifindex, 0);
+	return 0;
+}
+
+SEC("tc")
+int tc_redirect_ingress(struct __sk_buff *skb)
+{
+	ret = bpf_clone_redirect(skb, ifindex, BPF_F_INGRESS);
+	return 0;
+}
+
+SEC("tc")
+int tc_redirect_egress(struct __sk_buff *skb)
+{
+	ret = bpf_clone_redirect(skb, ifindex, 0);
+	return 0;
+}
Signature · 1 line
2.35.1
author maintainer
#369 lore raw

PATCH 370/1073 selftests/bpf: Mount debugfs in setns_by_fd

In reply to Greg Kroah-Hartman

From: Stanislav Fomichev <[email protected]>

[ Upstream commit 8ac88eece8009428e2577c345080a458e4507e2f ]

Jiri reports broken test_progs after recent commit 68f8e3d4b916 ("selftests/bpf: Make sure zero-len skbs aren't redirectable"). Apparently we don't remount debugfs when we switch back networking namespace. Let's explicitly mount /sys/kernel/debug.

0: https://lore.kernel.org/bpf/[email protected]/T/#ma66ca9c92e99eee0a25e40f422489b26ee0171c1

Fixes a30338840fa5 ("selftests/bpf: Move open_netns() and close_netns() into network_helpers.c")
---
 tools/testing/selftests/bpf/network_helpers.c            | 4 ++++
 tools/testing/selftests/bpf/prog_tests/empty_skb.c       | 2 +-
 tools/testing/selftests/bpf/prog_tests/xdp_do_redirect.c | 2 +-
 tools/testing/selftests/bpf/prog_tests/xdp_synproxy.c    | 2 +-
 4 files changed, 7 insertions(+), 3 deletions(-)
tools/testing/selftests/bpf/network_helpers.c +4 -0
index bec15558fd93..1f37adff7632 100644
@@ -426,6 +426,10 @@ static int setns_by_fd(int nsfd)
 	if (!ASSERT_OK(err, "mount /sys/fs/bpf"))
 		return err;
 
+	err = mount("debugfs", "/sys/kernel/debug", "debugfs", 0, NULL);
+	if (!ASSERT_OK(err, "mount /sys/kernel/debug"))
+		return err;
+
 	return 0;
 }
 
tools/testing/selftests/bpf/prog_tests/empty_skb.c +1 -1
index 32dd731e9070..0613f3bb8b5e 100644
@@ -9,7 +9,7 @@
 		goto out; \
 })
 
-void test_empty_skb(void)
+void serial_test_empty_skb(void)
 {
 	LIBBPF_OPTS(bpf_test_run_opts, tattr);
 	struct empty_skb *bpf_obj = NULL;
tools/testing/selftests/bpf/prog_tests/xdp_do_redirect.c +1 -1
index a50971c6cf4a..9ac6f6a268db 100644
@@ -85,7 +85,7 @@ static void test_max_pkt_size(int fd)
 }
 
 #define NUM_PKTS 10000
-void test_xdp_do_redirect(void)
+void serial_test_xdp_do_redirect(void)
 {
 	int err, xdp_prog_fd, tc_prog_fd, ifindex_src, ifindex_dst;
 	char data[sizeof(pkt_udp) + sizeof(__u32)];
tools/testing/selftests/bpf/prog_tests/xdp_synproxy.c +1 -1
index 874a846e298c..b49d14580e51 100644
@@ -174,7 +174,7 @@ static void test_synproxy(bool xdp)
 	system("ip netns del synproxy");
 }
 
-void test_xdp_synproxy(void)
+void serial_test_xdp_synproxy(void)
 {
 	if (test__start_subtest("xdp"))
 		test_synproxy(true);
Signature · 1 line
2.35.1
author maintainer
#370 lore raw

PATCH 371/1073 bonding: fix link recovery in mode 2 when updelay is nonzero

In reply to Greg Kroah-Hartman

From: Jonathan Toppins <[email protected]>

[ Upstream commit f8a65ab2f3ff7410921ebbf0dc55453102c33c56 ]

Before this change when a bond in mode 2 lost link, all of its slaves lost link, the bonding device would never recover even after the expiration of updelay. This change removes the updelay when the bond currently has no usable links. Conforming to bonding.txt section 13.1 paragraph 4.

Fixes 41f891004063 ("bonding: ignore updelay param when there is no active slave")
---
 drivers/net/bonding/bond_main.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/net/bonding/bond_main.c +10 -1
index c2939621b683..2ad17c840a2a 100644
@@ -2536,7 +2536,16 @@ static int bond_miimon_inspect(struct bonding *bond)
 	struct slave *slave;
 	bool ignore_updelay;
 
-	ignore_updelay = !rcu_dereference(bond->curr_active_slave);
+	if (BOND_MODE(bond) == BOND_MODE_ACTIVEBACKUP) {
+		ignore_updelay = !rcu_dereference(bond->curr_active_slave);
+	} else {
+		struct bond_up_slave *usable_slaves;
+
+		usable_slaves = rcu_dereference(bond->usable_slaves);
+
+		if (usable_slaves && usable_slaves->count == 0)
+			ignore_updelay = true;
+	}
 
 	bond_for_each_slave_rcu(bond, slave, iter) {
 		bond_propose_link_state(slave, BOND_LINK_NOCHANGE);
Signature · 1 line
2.35.1
author maintainer
#371 lore raw

PATCH 372/1073 mtd: core: Fix refcount error in del_mtd_device()

In reply to Greg Kroah-Hartman

From: Shang XiaoJing <[email protected]>

[ Upstream commit 56570bdad5e31c5c538cd6efff5c4510256e1bb4 ]

del_mtd_device() will call of_node_put() to mtd_get_of_node(mtd), which is mtd->dev.of_node. However, memset(&mtd->dev, 0) is called before of_node_put(). As the result, of_node_put() won't do anything in del_mtd_device(), and causes the refcount leak.

del_mtd_device()

    memset(&mtd->dev, 0, sizeof(mtd->dev) # clear mtd->dev
    of_node_put()
        mtd_get_of_node(mtd) # mtd->dev is cleared, can't locate of_node
                             # of_node_put(NULL) won't do anything

Fix the error by caching the pointer of the device_node.

OF: ERROR: memory leak, expected refcount 1 instead of 2, of_node_get()/of_node_put() unbalanced - destroy cset entry: attach overlay node /spi/spi-sram@0

CPU: 3 PID: 275 Comm: python3 Tainted: G N 6.1.0-rc3+ #54
    0d8a1edddf51f172ff5226989a7565c6313b08e2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
    dump_stack_lvl+0x67/0x83
    kobject_get+0x155/0x160
    of_node_get+0x1f/0x30
    of_fwnode_get+0x43/0x70
    fwnode_handle_get+0x54/0x80
    fwnode_get_nth_parent+0xc9/0xe0
    fwnode_full_name_string+0x3f/0xa0
    device_node_string+0x30f/0x750
    pointer+0x598/0x7a0
    vsnprintf+0x62d/0x9b0
    ...
    cfs_overlay_release+0x30/0x90
    config_item_release+0xbe/0x1a0
    config_item_put+0x5e/0x80
    configfs_rmdir+0x3bd/0x540
    vfs_rmdir+0x18c/0x320
    do_rmdir+0x198/0x330
    __x64_sys_rmdir+0x2c/0x40
    do_syscall_64+0x37/0x90
    entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes 00596576a051 ("mtd: core: clear out unregistered devices a bit more")
[<[email protected]>: Light reword of the commit log]
---
 drivers/mtd/mtdcore.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/mtd/mtdcore.c +3 -1
index 37050c551880..c14196bbf008 100644
@@ -776,6 +776,7 @@ int del_mtd_device(struct mtd_info *mtd)
 {
 	int ret;
 	struct mtd_notifier *not;
+	struct device_node *mtd_of_node;
 
 	mutex_lock(&mtd_table_mutex);
 
@@ -794,6 +795,7 @@ int del_mtd_device(struct mtd_info *mtd)
 		       mtd->index, mtd->name, mtd->usecount);
 		ret = -EBUSY;
 	} else {
+		mtd_of_node = mtd_get_of_node(mtd);
 		debugfs_remove_recursive(mtd->dbg.dfs_dir);
 
 		/* Try to remove the NVMEM provider */
@@ -805,7 +807,7 @@ int del_mtd_device(struct mtd_info *mtd)
 		memset(&mtd->dev, 0, sizeof(mtd->dev));
 
 		idr_remove(&mtd_idr, mtd->index);
-		of_node_put(mtd_get_of_node(mtd));
+		of_node_put(mtd_of_node);
 
 		module_put(THIS_MODULE);
 		ret = 0;
Signature · 1 line
2.35.1
author maintainer
#372 lore raw

PATCH 373/1073 mtd: maps: pxa2xx-flash: fix memory leak in probe

In reply to Greg Kroah-Hartman

From: Zheng Yongjun <[email protected]>

[ Upstream commit 2399401feee27c639addc5b7e6ba519d3ca341bf ]

Free 'info' upon remapping error to avoid a memory leak.

Fixes e644f7d62894 ("[MTD] MAPS: Merge Lubbock and Mainstone drivers into common PXA2xx driver")
[<[email protected]>: Reword the commit log]
---
 drivers/mtd/maps/pxa2xx-flash.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/mtd/maps/pxa2xx-flash.c +2 -0
index 1749dbbacc13..62a5bf41a6d7 100644
@@ -64,6 +64,7 @@ static int pxa2xx_flash_probe(struct platform_device *pdev)
 	if (!info->map.virt) {
 		printk(KERN_WARNING "Failed to ioremap %s\n",
 		       info->map.name);
+		kfree(info);
 		return -ENOMEM;
 	}
 	info->map.cached = ioremap_cache(info->map.phys, info->map.size);
@@ -85,6 +86,7 @@ static int pxa2xx_flash_probe(struct platform_device *pdev)
 		iounmap((void *)info->map.virt);
 		if (info->map.cached)
 			iounmap(info->map.cached);
+		kfree(info);
 		return -EIO;
 	}
 	info->mtd->dev.parent = &pdev->dev;
Signature · 1 line
2.35.1
author maintainer
#373 lore raw

PATCH 374/1073 drbd: remove call to memset before free device/resource/connection

In reply to Greg Kroah-Hartman

From: Wang ShaoBo <[email protected]>

[ Upstream commit 6e7b854e4c1b02dba00760dfa79d8dbf6cce561e ]

This revert c2258ffc56f2 ("drbd: poison free'd device, resource and connection structs"), add memset is odd here for debugging, there are some methods to accurately show what happened, such as kdump.

Stable-dep-of: 8692814b77ca ("drbd: destroy workqueue when drbd device was freed")

---
 drivers/block/drbd/drbd_main.c | 3 ---
 1 file changed, 3 deletions(-)
drivers/block/drbd/drbd_main.c +0 -3
index 8532b839a343..78cae4e75af1 100644
@@ -2217,7 +2217,6 @@ void drbd_destroy_device(struct kref *kref)
 		kref_put(&peer_device->connection->kref, drbd_destroy_connection);
 		kfree(peer_device);
 	}
-	memset(device, 0xfd, sizeof(*device));
 	kfree(device);
 	kref_put(&resource->kref, drbd_destroy_resource);
 }
@@ -2309,7 +2308,6 @@ void drbd_destroy_resource(struct kref *kref)
 	idr_destroy(&resource->devices);
 	free_cpumask_var(resource->cpu_mask);
 	kfree(resource->name);
-	memset(resource, 0xf2, sizeof(*resource));
 	kfree(resource);
 }
 
@@ -2650,7 +2648,6 @@ void drbd_destroy_connection(struct kref *kref)
 	drbd_free_socket(&connection->data);
 	kfree(connection->int_dig_in);
 	kfree(connection->int_dig_vv);
-	memset(connection, 0xfc, sizeof(*connection));
 	kfree(connection);
 	kref_put(&resource->kref, drbd_destroy_resource);
 }
Signature · 1 line
2.35.1
author maintainer
#374 lore raw

PATCH 375/1073 drbd: destroy workqueue when drbd device was freed

In reply to Greg Kroah-Hartman

From: Wang ShaoBo <[email protected]>

[ Upstream commit 8692814b77ca4228a99da8a005de0acf40af6132 ]

A submitter workqueue is dynamically allocated by init_submitter() called by drbd_create_device(), we should destroy it when this device is not needed or destroyed.

Fixes 113fef9e20e0 ("drbd: prepare to queue write requests on a submit worker")
---
 drivers/block/drbd/drbd_main.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/block/drbd/drbd_main.c +5 -1
index 78cae4e75af1..677240232684 100644
@@ -2217,6 +2217,8 @@ void drbd_destroy_device(struct kref *kref)
 		kref_put(&peer_device->connection->kref, drbd_destroy_connection);
 		kfree(peer_device);
 	}
+	if (device->submit.wq)
+		destroy_workqueue(device->submit.wq);
 	kfree(device);
 	kref_put(&resource->kref, drbd_destroy_resource);
 }
@@ -2771,7 +2773,7 @@ enum drbd_ret_code drbd_create_device(struct drbd_config_context *adm_ctx, unsig
 
 	err = add_disk(disk);
 	if (err)
-		goto out_idr_remove_from_resource;
+		goto out_destroy_workqueue;
 
 	/* inherit the connection state */
 	device->state.conn = first_connection(resource)->cstate;
@@ -2785,6 +2787,8 @@ enum drbd_ret_code drbd_create_device(struct drbd_config_context *adm_ctx, unsig
 	drbd_debugfs_device_add(device);
 	return NO_ERROR;
 
+out_destroy_workqueue:
+	destroy_workqueue(device->submit.wq);
 out_idr_remove_from_resource:
 	for_each_connection_safe(connection, n, resource) {
 		peer_device = idr_remove(&connection->peer_devices, vnr);
Signature · 1 line
2.35.1
author maintainer
#375 lore raw

PATCH 376/1073 ASoC: qcom: Add checks for devm_kcalloc

In reply to Greg Kroah-Hartman

From: Yuan Can <[email protected]>

[ Upstream commit 1bf5ee979076ceb121ee51c95197d890b1cee7f4 ]

As the devm_kcalloc may return NULL, the return value needs to be checked to avoid NULL poineter dereference.

Fixes 24caf8d9eb10 ("ASoC: qcom: lpass-sc7180: Add platform driver for lpass audio")
---
 sound/soc/qcom/lpass-sc7180.c | 3 +++
 1 file changed, 3 insertions(+)
sound/soc/qcom/lpass-sc7180.c +3 -0
index 77a556b27cf0..24a1c121cb2e 100644
@@ -131,6 +131,9 @@ static int sc7180_lpass_init(struct platform_device *pdev)
 
 	drvdata->clks = devm_kcalloc(dev, variant->num_clks,
 				     sizeof(*drvdata->clks), GFP_KERNEL);
+	if (!drvdata->clks)
+		return -ENOMEM;
+
 	drvdata->num_clks = variant->num_clks;
 
 	for (i = 0; i < drvdata->num_clks; i++)
Signature · 1 line
2.35.1
author maintainer
#376 lore raw

PATCH 377/1073 media: vimc: Fix wrong function called when vimc_init() fails

In reply to Greg Kroah-Hartman

From: Chen Zhongjin <[email protected]>

[ Upstream commit f74d3f326d1d5b8951ce263c59a121ecfa65e7c0 ]

In vimc_init(), when platform_driver_register(&vimc_pdrv) fails, platform_driver_unregister(&vimc_pdrv) is wrongly called rather than platform_device_unregister(&vimc_pdev), which causes kernel warning:

Unexpected driver unregister!

 WARNING: CPU: 1 PID: 14517 at drivers/base/driver.c:270 driver_unregister+0x8f/0xb0
 RIP: 0010:driver_unregister+0x8f/0xb0
 Call Trace:
  <TASK>
  vimc_init+0x7d/0x1000 [vimc]
  do_one_initcall+0xd0/0x4e0
  do_init_module+0x1cf/0x6b0
  load_module+0x65c2/0x7820
Fixes 4a29b7090749 ("[media] vimc: Subdevices as modules")
---
 drivers/media/test-drivers/vimc/vimc-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/test-drivers/vimc/vimc-core.c +1 -1
index 2ae7a0f11ebf..e82cfa5ffbf4 100644
@@ -433,7 +433,7 @@ static int __init vimc_init(void)
 	if (ret) {
 		dev_err(&vimc_pdev.dev,
 			"platform driver registration failed (err=%d)\n", ret);
-		platform_driver_unregister(&vimc_pdrv);
+		platform_device_unregister(&vimc_pdev);
 		return ret;
 	}
 
Signature · 1 line
2.35.1
author maintainer
#377 lore raw

PATCH 378/1073 media: imon: fix a race condition in send_packet()

In reply to Greg Kroah-Hartman

From: Gautam Menghani <[email protected]>

[ Upstream commit 813ceef062b53d68f296aa3cb944b21a091fabdb ]

The function send_packet() has a race condition as follows:

func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}

func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed mutex_unlock()
}

When the mutex is unlocked and the function send_packet() waits for the call to complete, vfd_write() can start another call, which leads to the "URB submitted while active" warning in usb_submit_urb(). Fix this by removing the mutex_unlock() call in send_packet() and using mutex_lock_interruptible().

Fixes 21677cfc562a ("V4L/DVB: ir-core: add imon driver")
Reported-by [email protected]
---
 drivers/media/rc/imon.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/media/rc/imon.c +3 -3
index 735b925da998..91d8056666ec 100644
@@ -646,15 +646,14 @@ static int send_packet(struct imon_context *ictx)
 		pr_err_ratelimited("error submitting urb(%d)\n", retval);
 	} else {
 		/* Wait for transmission to complete (or abort) */
-		mutex_unlock(&ictx->lock);
 		retval = wait_for_completion_interruptible(
 				&ictx->tx.finished);
 		if (retval) {
 			usb_kill_urb(ictx->tx_urb);
 			pr_err_ratelimited("task interrupted\n");
 		}
-		mutex_lock(&ictx->lock);
 
+		ictx->tx.busy = false;
 		retval = ictx->tx.status;
 		if (retval)
 			pr_err_ratelimited("packet tx failed (%d)\n", retval);
@@ -955,7 +954,8 @@ static ssize_t vfd_write(struct file *file, const char __user *buf,
 	if (ictx->disconnected)
 		return -ENODEV;
 
-	mutex_lock(&ictx->lock);
+	if (mutex_lock_interruptible(&ictx->lock))
+		return -ERESTARTSYS;
 
 	if (!ictx->dev_present_intf0) {
 		pr_err_ratelimited("no iMON device present\n");
Signature · 1 line
2.35.1
author maintainer
#378 lore raw

PATCH 379/1073 media: imx: imx7-media-csi: Clear BIT_MIPI_DOUBLE_CMPNT for <16b formats

In reply to Greg Kroah-Hartman

From: Laurent Pinchart <[email protected]>

[ Upstream commit cccc08a95ca57624563daafd47df5691e8c38995 ]

Commit 9babbbaaeb87 ("media: imx: imx7-media-csi: Use dual sampling for YUV 1X16") set BIT_MIPI_DOUBLE_CMPNT in the CR18 register for 16-bit YUV formats in imx7_csi_configure(). The CR18 register is always updated with read-modify-write cycles, so if a 16-bit YUV format is selected, the bit will stay set forever, even if the format is changed. Fix it by clearing the bit at the beginning of the imx7_csi_configure() function.

While at it, swap two of the bits being cleared to match the MSB to LSB order. This doesn't cause any functional change.

Fixes 9babbbaaeb87 ("media: imx: imx7-media-csi: Use dual sampling for YUV 1X16")
---
 drivers/staging/media/imx/imx7-media-csi.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/staging/media/imx/imx7-media-csi.c +3 -3
index a0553c24cce4..7eee2f8dca47 100644
@@ -521,9 +521,9 @@ static void imx7_csi_configure(struct imx7_csi *csi)
 	cr18 = imx7_csi_reg_read(csi, CSI_CSICR18);
 
 	cr18 &= ~(BIT_CSI_HW_ENABLE | BIT_MIPI_DATA_FORMAT_MASK |
-		  BIT_DATA_FROM_MIPI | BIT_BASEADDR_CHG_ERR_EN |
-		  BIT_BASEADDR_SWITCH_EN | BIT_BASEADDR_SWITCH_SEL |
-		  BIT_DEINTERLACE_EN);
+		  BIT_DATA_FROM_MIPI | BIT_MIPI_DOUBLE_CMPNT |
+		  BIT_BASEADDR_CHG_ERR_EN | BIT_BASEADDR_SWITCH_SEL |
+		  BIT_BASEADDR_SWITCH_EN | BIT_DEINTERLACE_EN);
 
 	if (out_pix->field == V4L2_FIELD_INTERLACED) {
 		cr18 |= BIT_DEINTERLACE_EN;
Signature · 1 line
2.35.1
author maintainer
#379 lore raw

PATCH 380/1073 media: mt9p031: Drop bogus v4l2_subdev_get_try_crop() call from mt9p031_init_cfg()

In reply to Greg Kroah-Hartman

From: Marek Vasut <[email protected]>

[ Upstream commit e208ad015f9310a87b4bb1ba1e4d3e347f391aa4 ]

The mt9p031_init_cfg() already calls __mt9p031_get_pad_crop(), which correctly calls v4l2_subdev_get_try_crop() on V4L2_SUBDEV_FORMAT_TRY or returns &mt9p031->crop on V4L2_SUBDEV_FORMAT_ACTIVE. No need to call v4l2_subdev_get_try_crop() in mt9p031_init_cfg() again in case of both V4L2_SUBDEV_FORMAT_TRY and V4L2_SUBDEV_FORMAT_ACTIVE.

This also fixes a splat generated by this call since commit
2ba3e38517f5a ("media: v4l: subdev: Fail graciously when getting try data for NULL state") because v4l2_subdev_get_try_crop() is called with sd_state = NULL
in mt9p031_init_cfg().

Fixes 69681cd041648 ("media: mt9p031: Move open subdev op init code into init_cfg")
---
 drivers/media/i2c/mt9p031.c | 1 -
 1 file changed, 1 deletion(-)
drivers/media/i2c/mt9p031.c +0 -1
index 1fd4dc6e4726..92f4e184353f 100644
@@ -702,7 +702,6 @@ static int mt9p031_init_cfg(struct v4l2_subdev *subdev,
 					     V4L2_SUBDEV_FORMAT_TRY;
 
 	crop = __mt9p031_get_pad_crop(mt9p031, sd_state, 0, which);
-	v4l2_subdev_get_try_crop(subdev, sd_state, 0);
 	crop->left = MT9P031_COLUMN_START_DEF;
 	crop->top = MT9P031_ROW_START_DEF;
 	crop->width = MT9P031_WINDOW_WIDTH_DEF;
Signature · 1 line
2.35.1
author maintainer
#380 lore raw

PATCH 381/1073 clk: imx8mn: rename vpu_pll to m7_alt_pll

In reply to Greg Kroah-Hartman

From: Dario Binacchi <[email protected]>

[ Upstream commit a429c60baefd95ab43a2ce7f25d5b2d7a2e431df ]

The IMX8MN platform does not have any video processing unit (VPU), and indeed in the reference manual (document IMX8MNRM Rev 2, 07/2022) there is no occurrence of its pll. From an analysis of the code and the RM itself, I think vpu pll is used instead of m7 alternate pll, probably for copy and paste of code taken from modules of similar architectures.

As an example for all, if we consider the second row of the "Clock Root" table of chapter 5 (Clocks and Power Management) of the RM:

Clock Root offset Source Select (CCM_TARGET_ROOTn[MUX])
... ... ...
ARM_M7_CLK_ROOT 0x8080 000 - 24M_REF_CLK

                                      001 - SYSTEM_PLL2_DIV5
				      010 - SYSTEM_PLL2_DIV4
				      011 - M7_ALT_PLL_CLK
				      100 - SYSTEM_PLL1_CLK
				      101 - AUDIO_PLL1_CLK
				      110 - VIDEO_PLL_CLK
				      111 - SYSTEM_PLL3_CLK
        ...          ...                    ...

but in the source code, the imx8mn_m7_sels clocks list contains vpu_pll for the source select bits 011b.

So, let's rename "vpu_pll" to "m7_alt_pll" to be consistent with the RM.

The IMX8MN_VPU_* constants have not been removed to ensure backward compatibility of the patch.

No functional changes intended.

---
 drivers/clk/imx/clk-imx8mn.c             | 16 ++++++++--------
 include/dt-bindings/clock/imx8mn-clock.h | 12 ++++++++----
 2 files changed, 16 insertions(+), 12 deletions(-)
drivers/clk/imx/clk-imx8mn.c +8 -8
index d37c45b676ab..72f9563a0ff6 100644
@@ -30,7 +30,7 @@ static const char * const audio_pll2_bypass_sels[] = {"audio_pll2", "audio_pll2_
 static const char * const video_pll1_bypass_sels[] = {"video_pll1", "video_pll1_ref_sel", };
 static const char * const dram_pll_bypass_sels[] = {"dram_pll", "dram_pll_ref_sel", };
 static const char * const gpu_pll_bypass_sels[] = {"gpu_pll", "gpu_pll_ref_sel", };
-static const char * const vpu_pll_bypass_sels[] = {"vpu_pll", "vpu_pll_ref_sel", };
+static const char * const m7_alt_pll_bypass_sels[] = {"m7_alt_pll", "m7_alt_pll_ref_sel", };
 static const char * const arm_pll_bypass_sels[] = {"arm_pll", "arm_pll_ref_sel", };
 static const char * const sys_pll3_bypass_sels[] = {"sys_pll3", "sys_pll3_ref_sel", };
 
@@ -40,7 +40,7 @@ static const char * const imx8mn_a53_sels[] = {"osc_24m", "arm_pll_out", "sys_pl
 
 static const char * const imx8mn_a53_core_sels[] = {"arm_a53_div", "arm_pll_out", };
 
-static const char * const imx8mn_m7_sels[] = {"osc_24m", "sys_pll2_200m", "sys_pll2_250m", "vpu_pll_out",
+static const char * const imx8mn_m7_sels[] = {"osc_24m", "sys_pll2_200m", "sys_pll2_250m", "m7_alt_pll_out",
 				       "sys_pll1_800m", "audio_pll1_out", "video_pll1_out", "sys_pll3_out", };
 
 static const char * const imx8mn_gpu_core_sels[] = {"osc_24m", "gpu_pll_out", "sys_pll1_800m",
@@ -252,10 +252,10 @@ static const char * const imx8mn_gpt6_sels[] = {"osc_24m", "sys_pll2_100m", "sys
 						"audio_pll1_out", "clk_ext1", };
 
 static const char * const imx8mn_wdog_sels[] = {"osc_24m", "sys_pll1_133m", "sys_pll1_160m",
-						"vpu_pll_out", "sys_pll2_125m", "sys_pll3_out",
+						"m7_alt_pll_out", "sys_pll2_125m", "sys_pll3_out",
 						"sys_pll1_80m", "sys_pll2_166m", };
 
-static const char * const imx8mn_wrclk_sels[] = {"osc_24m", "sys_pll1_40m", "vpu_pll_out",
+static const char * const imx8mn_wrclk_sels[] = {"osc_24m", "sys_pll1_40m", "m7_alt_pll_out",
 						 "sys_pll3_out", "sys_pll2_200m", "sys_pll1_266m",
 						 "sys_pll2_500m", "sys_pll1_100m", };
 
@@ -352,7 +352,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_VIDEO_PLL1_REF_SEL] = imx_clk_hw_mux("video_pll1_ref_sel", base + 0x28, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_DRAM_PLL_REF_SEL] = imx_clk_hw_mux("dram_pll_ref_sel", base + 0x50, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_GPU_PLL_REF_SEL] = imx_clk_hw_mux("gpu_pll_ref_sel", base + 0x64, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
-	hws[IMX8MN_VPU_PLL_REF_SEL] = imx_clk_hw_mux("vpu_pll_ref_sel", base + 0x74, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
+	hws[IMX8MN_M7_ALT_PLL_REF_SEL] = imx_clk_hw_mux("m7_alt_pll_ref_sel", base + 0x74, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_ARM_PLL_REF_SEL] = imx_clk_hw_mux("arm_pll_ref_sel", base + 0x84, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_SYS_PLL3_REF_SEL] = imx_clk_hw_mux("sys_pll3_ref_sel", base + 0x114, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 
@@ -361,7 +361,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_VIDEO_PLL1] = imx_clk_hw_pll14xx("video_pll1", "video_pll1_ref_sel", base + 0x28, &imx_1443x_pll);
 	hws[IMX8MN_DRAM_PLL] = imx_clk_hw_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_dram_pll);
 	hws[IMX8MN_GPU_PLL] = imx_clk_hw_pll14xx("gpu_pll", "gpu_pll_ref_sel", base + 0x64, &imx_1416x_pll);
-	hws[IMX8MN_VPU_PLL] = imx_clk_hw_pll14xx("vpu_pll", "vpu_pll_ref_sel", base + 0x74, &imx_1416x_pll);
+	hws[IMX8MN_M7_ALT_PLL] = imx_clk_hw_pll14xx("m7_alt_pll", "m7_alt_pll_ref_sel", base + 0x74, &imx_1416x_pll);
 	hws[IMX8MN_ARM_PLL] = imx_clk_hw_pll14xx("arm_pll", "arm_pll_ref_sel", base + 0x84, &imx_1416x_pll);
 	hws[IMX8MN_SYS_PLL1] = imx_clk_hw_fixed("sys_pll1", 800000000);
 	hws[IMX8MN_SYS_PLL2] = imx_clk_hw_fixed("sys_pll2", 1000000000);
@@ -373,7 +373,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_VIDEO_PLL1_BYPASS] = imx_clk_hw_mux_flags("video_pll1_bypass", base + 0x28, 16, 1, video_pll1_bypass_sels, ARRAY_SIZE(video_pll1_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_DRAM_PLL_BYPASS] = imx_clk_hw_mux_flags("dram_pll_bypass", base + 0x50, 16, 1, dram_pll_bypass_sels, ARRAY_SIZE(dram_pll_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_GPU_PLL_BYPASS] = imx_clk_hw_mux_flags("gpu_pll_bypass", base + 0x64, 28, 1, gpu_pll_bypass_sels, ARRAY_SIZE(gpu_pll_bypass_sels), CLK_SET_RATE_PARENT);
-	hws[IMX8MN_VPU_PLL_BYPASS] = imx_clk_hw_mux_flags("vpu_pll_bypass", base + 0x74, 28, 1, vpu_pll_bypass_sels, ARRAY_SIZE(vpu_pll_bypass_sels), CLK_SET_RATE_PARENT);
+	hws[IMX8MN_M7_ALT_PLL_BYPASS] = imx_clk_hw_mux_flags("m7_alt_pll_bypass", base + 0x74, 28, 1, m7_alt_pll_bypass_sels, ARRAY_SIZE(m7_alt_pll_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_ARM_PLL_BYPASS] = imx_clk_hw_mux_flags("arm_pll_bypass", base + 0x84, 28, 1, arm_pll_bypass_sels, ARRAY_SIZE(arm_pll_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_SYS_PLL3_BYPASS] = imx_clk_hw_mux_flags("sys_pll3_bypass", base + 0x114, 28, 1, sys_pll3_bypass_sels, ARRAY_SIZE(sys_pll3_bypass_sels), CLK_SET_RATE_PARENT);
 
@@ -383,7 +383,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_VIDEO_PLL1_OUT] = imx_clk_hw_gate("video_pll1_out", "video_pll1_bypass", base + 0x28, 13);
 	hws[IMX8MN_DRAM_PLL_OUT] = imx_clk_hw_gate("dram_pll_out", "dram_pll_bypass", base + 0x50, 13);
 	hws[IMX8MN_GPU_PLL_OUT] = imx_clk_hw_gate("gpu_pll_out", "gpu_pll_bypass", base + 0x64, 11);
-	hws[IMX8MN_VPU_PLL_OUT] = imx_clk_hw_gate("vpu_pll_out", "vpu_pll_bypass", base + 0x74, 11);
+	hws[IMX8MN_M7_ALT_PLL_OUT] = imx_clk_hw_gate("m7_alt_pll_out", "m7_alt_pll_bypass", base + 0x74, 11);
 	hws[IMX8MN_ARM_PLL_OUT] = imx_clk_hw_gate("arm_pll_out", "arm_pll_bypass", base + 0x84, 11);
 	hws[IMX8MN_SYS_PLL3_OUT] = imx_clk_hw_gate("sys_pll3_out", "sys_pll3_bypass", base + 0x114, 11);
 
include/dt-bindings/clock/imx8mn-clock.h +8 -4
index 07b8a282c268..694e3c050d04 100644
@@ -19,7 +19,8 @@
 #define IMX8MN_VIDEO_PLL1_REF_SEL		10
 #define IMX8MN_DRAM_PLL_REF_SEL			11
 #define IMX8MN_GPU_PLL_REF_SEL			12
-#define IMX8MN_VPU_PLL_REF_SEL			13
+#define IMX8MN_M7_ALT_PLL_REF_SEL		13
+#define IMX8MN_VPU_PLL_REF_SEL			IMX8MN_M7_ALT_PLL_REF_SEL
 #define IMX8MN_ARM_PLL_REF_SEL			14
 #define IMX8MN_SYS_PLL1_REF_SEL			15
 #define IMX8MN_SYS_PLL2_REF_SEL			16
@@ -29,7 +30,8 @@
 #define IMX8MN_VIDEO_PLL1			20
 #define IMX8MN_DRAM_PLL				21
 #define IMX8MN_GPU_PLL				22
-#define IMX8MN_VPU_PLL				23
+#define IMX8MN_M7_ALT_PLL			23
+#define IMX8MN_VPU_PLL				IMX8MN_M7_ALT_PLL
 #define IMX8MN_ARM_PLL				24
 #define IMX8MN_SYS_PLL1				25
 #define IMX8MN_SYS_PLL2				26
@@ -39,7 +41,8 @@
 #define IMX8MN_VIDEO_PLL1_BYPASS		30
 #define IMX8MN_DRAM_PLL_BYPASS			31
 #define IMX8MN_GPU_PLL_BYPASS			32
-#define IMX8MN_VPU_PLL_BYPASS			33
+#define IMX8MN_M7_ALT_PLL_BYPASS		33
+#define IMX8MN_VPU_PLL_BYPASS			IMX8MN_M7_ALT_PLL_BYPASS
 #define IMX8MN_ARM_PLL_BYPASS			34
 #define IMX8MN_SYS_PLL1_BYPASS			35
 #define IMX8MN_SYS_PLL2_BYPASS			36
@@ -49,7 +52,8 @@
 #define IMX8MN_VIDEO_PLL1_OUT			40
 #define IMX8MN_DRAM_PLL_OUT			41
 #define IMX8MN_GPU_PLL_OUT			42
-#define IMX8MN_VPU_PLL_OUT			43
+#define IMX8MN_M7_ALT_PLL_OUT			43
+#define IMX8MN_VPU_PLL_OUT			IMX8MN_M7_ALT_PLL_OUT
 #define IMX8MN_ARM_PLL_OUT			44
 #define IMX8MN_SYS_PLL1_OUT			45
 #define IMX8MN_SYS_PLL2_OUT			46
Signature · 1 line
2.35.1
author maintainer
#381 lore raw

PATCH 382/1073 clk: imx: replace osc_hdmi with dummy

In reply to Greg Kroah-Hartman

From: Dario Binacchi <[email protected]>

[ Upstream commit e7fa365ff66f16772dc06b480cd78f858d10856b ]

There is no occurrence of the hdmi oscillator in the reference manual (document IMX8MNRM Rev 2, 07/2022). Further, if we consider the indexes 76-81 and 134 of the "Clock Root" table of chapter 5 of the RM, there is no entry for the source select bits 101b, which is the setting referenced by "osc_hdmi".
Fix by renaming "osc_hdmi" with "dummy", a clock which has already been used for missing source select bits.

Tested on the BSH SystemMaster (SMM) S2 board.

Fixes 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver")
---
 drivers/clk/imx/clk-imx8mn.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/clk/imx/clk-imx8mn.c +6 -6
index 72f9563a0ff6..0fae97e61e2c 100644
@@ -108,27 +108,27 @@ static const char * const imx8mn_disp_pixel_sels[] = {"osc_24m", "video_pll1_out
 						      "sys_pll3_out", "clk_ext4", };
 
 static const char * const imx8mn_sai2_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_sai3_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_sai5_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext2", "clk_ext3", };
 
 static const char * const imx8mn_sai6_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_sai7_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_spdif1_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						  "video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						  "video_pll1_out", "sys_pll1_133m", "dummy",
 						  "clk_ext2", "clk_ext3", };
 
 static const char * const imx8mn_enet_ref_sels[] = {"osc_24m", "sys_pll2_125m", "sys_pll2_50m",
Signature · 1 line
2.35.1