USB DWC3 QCOM Multi power domain support
Subsystems (6)
cover USB DWC3 QCOM Multi power domain support
Add multi pd support to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Add corresponding dt bindings, driver changes and dt changes.
Sandeep Maheswaram (3):
dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
usb: dwc3: qcom: Add multi-pd support
arm64: dts: qcom: sc7280: Add cx power domain support
.../devicetree/bindings/usb/qcom,dwc3.yaml | 13 +++++- arch/arm64/boot/dts/qcom/sc7280.dtsi | 5 ++- drivers/usb/dwc3/dwc3-qcom.c | 49 ++++++++++++++++++++++ 3 files changed, 65 insertions(+), 2 deletions(-)
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
PATCH 1/3 dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
Add multi pd bindings to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
--- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +12 -1
@@ -41,7 +41,18 @@ properties: power-domains: description: specifies a phandle to PM domain provider node - maxItems: 1 + minItems: 1 + items: + - description: optional,cx power domain + - description: USB gdsc power domain + + power-domain-names: + items: + - const: cx + - const: usb_gdsc + + required-opps: + description: specifies the performance state to cx power domain clocks: description:
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH 1/3] dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
Hi,
Quoted 14 lines · Sandeep Maheswaram
Add multi pd bindings to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Signed-off-by Sandeep Maheswaram <[email protected]>--- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +0
-0
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml properties: · line 47
Quoted 8 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +4
-1@@ -41,7 +41,18 @@ properties: power-domains: description: specifies a phandle to PM domain provider node - maxItems: 1 + minItems: 1 + items: + - description: optional,cx power domain + - description: USB gdsc power domain
You need to re-order the above. The optional one needs to be second, not first.
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml properties: · line 52
Quoted 4 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +4
-0+ power-domain-names: + items: + - const: cx + - const: usb_gdsc
Why do you need the names at all? The ordering of power-domains is well defined and there are no holes in it and there are no legacy reasons for having the names (like there are for clocks), so you should drop. This is much like reg-names and I always point people to this message from Rob Herring about reg-names:
https://lore.kernel.org/r/CAL_Jsq+MMunmVWqeW9v2RyzsMKP+=kMzeTHNMG4JDHM7Fy0HBg@mail.gmail.com/
You'll have to change your driver to use dev_pm_domain_attach_by_id() but that should be fine.
-Doug
Re: [PATCH 1/3] dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
Quoted 17 lines · Doug Anderson
Hi,
Quoted 14 lines · Sandeep Maheswaram
Add multi pd bindings to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Signed-off-by Sandeep Maheswaram <[email protected]>--- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +0
-0@@ -41,7 +41,18 @@ properties:
Quoted 9 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml properties: · line 47
Quoted 7 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +4
-1power-domains: description: specifies a phandle to PM domain provider node - maxItems: 1 + minItems: 1 + items: + - description: optional,cx power domain + - description: USB gdsc power domainYou need to re-order the above. The optional one needs to be second, not first.
I wanted to use required-opps for cx domain only. so I have put it first in order.
Quoted 10 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml properties: · line 52
Quoted 4 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +4
-0+ power-domain-names: + items: + - const: cx + - const: usb_gdscWhy do you need the names at all? The ordering of power-domains is well defined and there are no holes in it and there are no legacy reasons for having the names (like there are for clocks), so you should drop. This is much like reg-names and I always point people to this message from Rob Herring about reg-names:
Quoted 6 lines
https://lore.kernel.org/r/CAL_Jsq+MMunmVWqeW9v2RyzsMKP+=kMzeTHNMG4JDHM7Fy0HBg@mail.gmail.com/
You'll have to change your driver to use
dev_pm_domain_attach_by_id()but that should be fine.-Doug
Ok..I will try using dev_pm_domain_attach_by_id()
Re: [PATCH 1/3] dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
Quoted 28 lines · Sandeep Maheswaram
Quoted 17 lines · Doug Anderson
Hi,
Quoted 14 lines · Sandeep Maheswaram
Add multi pd bindings to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Signed-off-by Sandeep Maheswaram <[email protected]>---
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml| 13 ++++++++++++-1 file changed, 12 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +0
-0@@ -41,7 +41,18 @@ properties:Quoted 9 lines
Quoted 7 lines
power-domains:
description: specifies a phandle to PM domain provider node - maxItems: 1
+ minItems: 1
+ items:
+ - description: optional,cx power domain
+ - description: USB gdsc power domainYou need to re-order the above. The optional one needs to be second, not first.
Quoted 1 line
I wanted to use required-opps for cx domain only. so I have put it first in order.
You can always put a <> for the power-domains for which there are no required-opps
+ power-domain-names = "usb_gdsc", "cx";
+
+ required-opps = <>, <&rpmhpd_opp_nom>;
Quoted 20 lines
Quoted 10 lines
Quoted 4 lines
+ power-domain-names:
+ items:
+ - const: cx
+ - const:usb_gdscWhy do you need the names at all? The ordering of power-domains is well defined and there are no holes in it and there are no legacy reasons for having the names (like there are for clocks), so you should drop. This is much like reg-names and I always point people to this message from Rob Herring about reg-names:
Quoted 6 lines
https://lore.kernel.org/r/CAL_Jsq+MMunmVWqeW9v2RyzsMKP+=kMzeTHNMG4JDHM7Fy0HBg@mail.gmail.com/
You'll have to change your driver to use
dev_pm_domain_attach_by_id()but that should be fine.-Doug
Ok..I will try using
dev_pm_domain_attach_by_id()
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH 1/3] dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
In reply to Sandeep MaheswaramQuoted 16 lines · Sandeep Maheswaram
Add multi pd bindings to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Signed-off-by Sandeep Maheswaram <[email protected]>--- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +0
-0@@ -41,7 +41,18 @@ properties: power-domains: description: specifies a phandle to PM domain provider node
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml properties: · line 52
Quoted 10 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +9
-1- maxItems: 1 + minItems: 1 + items: + - description: optional,cx power domain + - description: USB gdsc power domain + + power-domain-names: + items: + - const: cx + - const: usb_gdsc
But "usb_gdsc" is a subdomain of "cx", why can't we describe this fact in gcc?
Regards,
Bjorn
Quoted 10 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +3
-0+ + required-opps: + description: specifies the performance state to cx power domain clocks: description:Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
A message that is not in the archive (sent off-list or not yet received): [email protected]
Re: [PATCH 1/3] dt-bindings: usb: qcom,dwc3: Add multi-pd bindings for dwc3 qcom
Quoted 32 lines · Sandeep Maheswaram
Quoted 30 lines · Bjorn Andersson
Quoted 15 lines · Sandeep Maheswaram
Add multi pd bindings to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Signed-off-by Sandeep Maheswaram <[email protected]>--- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +0
-0@@ -41,7 +41,18 @@ properties: power-domains: description: specifies a phandle to PM domain provider nodeDocumentation/devicetree/bindings/usb/qcom,dwc3.yaml properties: · line 51
Quoted 10 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +9
-1- maxItems: 1 + minItems: 1 + items: + - description: optional,cx power domain + - description: USB gdsc power domain + + power-domain-names: + items: + - const: cx + - const: usb_gdscBut "
usb_gdsc" is a subdomain of "cx", why can't we describe this fact in gcc?
Quoted 6 lines
Quoted 2 lines
Regards,
BjornThanks for your review.
Any idea on how can this be described in gcc ? Can you point any reference for this .
There's a series from Dmitry that defines such a relationship between MDSS_GDSC and the MMCX domain on SM8250. This seems like a continuation of that support, given that we have multiple parent domains (cx, mx etc).
You can find that discussion here:
https://lore.kernel.org/all/[email protected]/
Regards,
Bjorn
Quoted 11 lines
Regards
SandeepQuoted 9 lines
Quoted 9 lines
Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +3
-1+ + required-opps: + description: specifies the performance state to cx power domain clocks: description: --QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
PATCH 2/3 usb: dwc3: qcom: Add multi-pd support
In reply to Sandeep MaheswaramAdd multi pd support to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
--- drivers/usb/dwc3/dwc3-qcom.c | 49 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+)
drivers/usb/dwc3/dwc3-qcom.c +49 -0
@@ -17,6 +17,7 @@#include <linux/of_platform.h> #include <linux/platform_device.h> #include <linux/phy/phy.h> +#include <linux/pm_domain.h> #include <linux/usb/of.h> #include <linux/reset.h> #include <linux/iopoll.h>
@@ -89,6 +90,10 @@ struct dwc3_qcom {bool pm_suspended;struct icc_path *icc_path_ddr;struct icc_path *icc_path_apps; +/* power domain for cx */ +struct device *pd_cx; +/* power domain for usb gdsc */ +struct device *pd_usb_gdsc; };static inline void dwc3_qcom_setbits (void __iomem *base,u32 offset,u32 val)
@@ -521,6 +526,46 @@ static int dwc3_qcom_setup_irq(struct platform_device *pdev)return 0 ; } +static int dwc3_qcom_attach_pd (struct device *dev) +{ +struct dwc3_qcom *qcom =dev_get_drvdata (dev); +struct device_link *link; + +/* Do nothing when in a single power domain */ +if (dev->pm_domain) +return 0 ; + + qcom->pd_cx =dev_pm_domain_attach_by_name (dev,"cx" ); +if (IS_ERR (qcom->pd_cx)) +return PTR_ERR (qcom->pd_cx); +/* Do nothing when power domain missing */ +if (!qcom->pd_cx) +return 0 ; + link =device_link_add (dev, qcom->pd_cx, +DL_FLAG_STATELESS | +DL_FLAG_PM_RUNTIME | +DL_FLAG_RPM_ACTIVE ); +if (!link) { +dev_err (dev,"Failed to add device_link to cx pd.\n" ); +return -EINVAL ; + } + + qcom->pd_usb_gdsc =dev_pm_domain_attach_by_name (dev,"usb_gdsc" ); +if (IS_ERR (qcom->pd_usb_gdsc)) +return PTR_ERR (qcom->pd_usb_gdsc); + + link =device_link_add (dev, qcom->pd_usb_gdsc, +DL_FLAG_STATELESS | +DL_FLAG_PM_RUNTIME | +DL_FLAG_RPM_ACTIVE ); +if (!link) { +dev_err (dev,"Failed to add device_link to usb gdsc pd.\n" ); +return -EINVAL ; + } + +return 0 ; +} +static int dwc3_qcom_clk_init (struct dwc3_qcom *qcom,int count) {struct device *dev = qcom->dev;
@@ -837,6 +882,10 @@ static int dwc3_qcom_probe(struct platform_device *pdev)if (ret) goto interconnect_exit; + ret =dwc3_qcom_attach_pd (dev); +if (ret) + goto interconnect_exit; +device_init_wakeup (&pdev->dev,1 ); qcom->is_suspended = false;pm_runtime_set_active (dev);
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Re: [PATCH 2/3] usb: dwc3: qcom: Add multi-pd support
Hi,
Quoted 46 lines · Sandeep Maheswaram
Add multi pd support to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
Signed-off-by Sandeep Maheswaram <[email protected]>--- drivers/usb/dwc3/dwc3-qcom.c | 49 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+)drivers/usb/dwc3/dwc3-qcom.c +16
-0@@ -17,6 +17,7 @@#include <linux/of_platform.h> #include <linux/platform_device.h> #include <linux/phy/phy.h> +#include <linux/pm_domain.h> #include <linux/usb/of.h> #include <linux/reset.h> #include <linux/iopoll.h> @@ -89,6 +90,10 @@ struct dwc3_qcom {bool pm_suspended;struct icc_path *icc_path_ddr;struct icc_path *icc_path_apps; +/* power domain for cx */ +struct device *pd_cx; +/* power domain for usb gdsc */ +struct device *pd_usb_gdsc; };static inline void dwc3_qcom_setbits (void __iomem *base,u32 offset,u32 val)@@ -521,6 +526,46 @@ static int dwc3_qcom_setup_irq(struct platform_device *pdev)return 0 ; } +static int dwc3_qcom_attach_pd (struct device *dev) +{ +struct dwc3_qcom *qcom =dev_get_drvdata (dev); +struct device_link *link; + +/* Do nothing when in a single power domain */ +if (dev->pm_domain) +return 0 ; + + qcom->pd_cx =dev_pm_domain_attach_by_name (dev,"cx" ); +if (IS_ERR (qcom->pd_cx))
drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_setup_irq(struct platform_device *pdev) · line 549
Quoted 10 lines
drivers/usb/dwc3/dwc3-qcom.c +10
-0+return PTR_ERR (qcom->pd_cx); +/* Do nothing when power domain missing */ +if (!qcom->pd_cx) +return 0 ; + link =device_link_add (dev, qcom->pd_cx, +DL_FLAG_STATELESS | +DL_FLAG_PM_RUNTIME | +DL_FLAG_RPM_ACTIVE ); +if (!link) { +dev_err (dev,"Failed to add device_link to cx pd.\n" );
do you need to call dev_pm_domain_dettach() here?
drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_setup_irq(struct platform_device *pdev) · line 554
Quoted 5 lines
drivers/usb/dwc3/dwc3-qcom.c +5
-0+return -EINVAL ; + } + + qcom->pd_usb_gdsc =dev_pm_domain_attach_by_name (dev,"usb_gdsc" ); +if (IS_ERR (qcom->pd_usb_gdsc))
do you need to call dev_pm_domain_dettach() here?
drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_setup_irq(struct platform_device *pdev) · line 562
Quoted 8 lines
drivers/usb/dwc3/dwc3-qcom.c +8
-0+return PTR_ERR (qcom->pd_usb_gdsc); + + link =device_link_add (dev, qcom->pd_usb_gdsc, +DL_FLAG_STATELESS | +DL_FLAG_PM_RUNTIME | +DL_FLAG_RPM_ACTIVE ); +if (!link) { +dev_err (dev,"Failed to add device_link to usb gdsc pd.\n" );
do you need to call dev_pm_domain_dettach() here?
Signature · 1 line
balbi
PATCH 3/3 arm64: dts: qcom: sc7280: Add cx power domain support
In reply to Sandeep MaheswaramAdd multi pd support to set performance state for cx domain to maintain minimum corner voltage for USB clocks.
--- arch/arm64/boot/dts/qcom/sc7280.dtsi | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/qcom/sc7280.dtsi +4 -1
@@ -1374,7 +1374,10 @@ interrupt-names = "hs_phy_irq", "dp_hs_phy_irq", "dm_hs_phy_irq", "ss_phy_irq"; - power-domains = <&gcc GCC_USB30_PRIM_GDSC>; + power-domains = <&rpmhpd SC7280_CX>, <&gcc GCC_USB30_PRIM_GDSC>; + power-domain-names = "cx", "usb_gdsc"; + + required-opps = <&rpmhpd_opp_nom>; resets = <&gcc GCC_USB30_PRIM_BCR>;
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation