pci: pcie_dw_rockchip: Add rk3588 compatible
Subsystems (4)
PATCH v2 1/7 pci: pcie_dw_rockchip: Add rk3588 compatible
From: Jon Lin <[email protected]>
Add compatible for RK3588 SoC.
---
Changes in v2:
- none
drivers/pci/pcie_dw_rockchip.c | 1 + 1 file changed, 1 insertion(+)
drivers/pci/pcie_dw_rockchip.c +1 -0
@@ -468,6 +468,7 @@ static const struct dm_pci_ops rockchip_pcie_ops = {static const struct udevice_id rockchip_pcie_ids[] = { { .compatible ="rockchip,rk3568-pcie" }, + { .compatible ="rockchip,rk3588-pcie" }, { } };
Signature · 1 line
2.34.1
PATCH v2 2/7 pci: pcie_dw_rockchip: Support max_link_speed dts property
From: Jon Lin <[email protected]>
Add support for max_link_speed specified in the PCI DT binding.
[[email protected]: port to latest API, set default correctly, align to 80 chars]
---
Changes in v2:
- move to dev_read_u32_default
drivers/pci/pcie_dw_rockchip.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/pci/pcie_dw_rockchip.c +5 -1
@@ -42,6 +42,7 @@ struct rk_pcie {struct clk_bulk clks;struct reset_ctl_bulk rsts;struct gpio_desc rst_gpio; +u32 gen; };/* Parameters for the waiting for iATU enabled routine */
@@ -331,7 +332,7 @@ static int rockchip_pcie_init_port(struct udevice *dev)rk_pcie_writel_apb (priv,0x0 ,0xf00040 );pcie_dw_setup_host (&priv->dw); - ret =rk_pcie_link_up (priv,LINK_SPEED_GEN_3 ); + ret =rk_pcie_link_up (priv, priv->gen);if (ret <0 ) goto err_link_up;
@@ -397,6 +398,9 @@ static int rockchip_pcie_parse_dt(struct udevice *dev) goto rockchip_pcie_parse_dt_err_phy_get_by_index; } + priv->gen =dev_read_u32_default (dev,"max-link-speed" , +LINK_SPEED_GEN_3 ); +return 0 ; rockchip_pcie_parse_dt_err_phy_get_by_index:
Signature · 1 line
2.34.1
Re: [PATCH v2 2/7] pci: pcie_dw_rockchip: Support max_link_speed dts property
Quoted 10 lines · Eugen Hristev
From: Jon Lin <[email protected]>
Add support for
max_link_speedspecified in the PCI DT binding.Signed-off-by Jon Lin <[email protected]>[[email protected]: port to latest API, set default correctly, align to 80 chars]
Signed-off-by Eugen Hristev <[email protected]>[[email protected]: switch to dev_read_u32_default]Signed-off-by Jonas Karlman <[email protected]>
Thanks,
- Kever
Quoted 38 lines
---
Changes in v2:
- move todev_read_u32_defaultdrivers/pci/pcie_dw_rockchip.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)drivers/pci/pcie_dw_rockchip.c +5
-1@@ -42,6 +42,7 @@ struct rk_pcie {struct clk_bulk clks;struct reset_ctl_bulk rsts;struct gpio_desc rst_gpio; +u32 gen; };/* Parameters for the waiting for iATU enabled routine */ @@ -331,7 +332,7 @@ static int rockchip_pcie_init_port(struct udevice *dev)rk_pcie_writel_apb (priv,0x0 ,0xf00040 );pcie_dw_setup_host (&priv->dw); - ret =rk_pcie_link_up (priv,LINK_SPEED_GEN_3 ); + ret =rk_pcie_link_up (priv, priv->gen);if (ret <0 ) goto err_link_up;@@ -397,6 +398,9 @@ static int rockchip_pcie_parse_dt(struct udevice *dev) goto rockchip_pcie_parse_dt_err_phy_get_by_index; } + priv->gen =dev_read_u32_default (dev,"max-link-speed" , +LINK_SPEED_GEN_3 ); +return 0 ; rockchip_pcie_parse_dt_err_phy_get_by_index:
PATCH v2 3/7 phy: rockchip: naneng-combphy: Add support for multiple resets
In reply to Eugen HristevSome variants of the PHY have more than just one reset. To cover all cases, request the rests in bulk rather than just the reset at index 0.
---
Changes in v2:
- none
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +4 -4
@@ -76,7 +76,7 @@ struct rockchip_combphy_priv {struct regmap *pipe_grf;struct regmap *phy_grf;struct phy *phy; -struct reset_ctl phy_rst; +struct reset_ctl_bulk phy_rsts;struct clk ref_clk;const struct rockchip_combphy_cfg *cfg; };
@@ -189,7 +189,7 @@ static int rockchip_combphy_init(struct phy *phy)if (ret) goto err_clk; -reset_deassert (&priv->phy_rst); +reset_deassert_bulk (&priv->phy_rsts);return 0 ;
@@ -204,7 +204,7 @@ static int rockchip_combphy_exit(struct phy *phy)struct rockchip_combphy_priv *priv =dev_get_priv (phy->dev);clk_disable (&priv->ref_clk); -reset_assert (&priv->phy_rst); +reset_assert_bulk (&priv->phy_rsts);return 0 ; }
@@ -255,7 +255,7 @@ static int rockchip_combphy_parse_dt(struct udevice *dev,return PTR_ERR (&priv->ref_clk); } - ret =reset_get_by_index (dev,0 , &priv->phy_rst); + ret =reset_get_bulk (dev, &priv->phy_rsts);if (ret) {dev_err (dev,"no phy reset control specified\n" );return ret;
Signature · 1 line
2.34.1
Re: [PATCH v2 3/7] phy: rockchip: naneng-combphy: Add support for multiple resets
Quoted 7 lines · Eugen Hristev
Some variants of the PHY have more than just one reset. To cover all cases, request the rests in bulk rather than just the reset at index 0.
Co-developed-by Ren Jianing <[email protected]>Signed-off-by Ren Jianing <[email protected]>Signed-off-by Eugen Hristev <[email protected]>
Thanks,
- Kever
Quoted 47 lines
---
Changes in v2:
- nonedrivers/phy/rockchip/phy-rockchip-naneng-combphy.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +4
-4@@ -76,7 +76,7 @@ struct rockchip_combphy_priv {struct regmap *pipe_grf;struct regmap *phy_grf;struct phy *phy; -struct reset_ctl phy_rst; +struct reset_ctl_bulk phy_rsts;struct clk ref_clk;const struct rockchip_combphy_cfg *cfg; };@@ -189,7 +189,7 @@ static int rockchip_combphy_init(struct phy *phy)if (ret) goto err_clk; -reset_deassert (&priv->phy_rst); +reset_deassert_bulk (&priv->phy_rsts);return 0 ;@@ -204,7 +204,7 @@ static int rockchip_combphy_exit(struct phy *phy)struct rockchip_combphy_priv *priv =dev_get_priv (phy->dev);clk_disable (&priv->ref_clk); -reset_assert (&priv->phy_rst); +reset_assert_bulk (&priv->phy_rsts);return 0 ; }@@ -255,7 +255,7 @@ static int rockchip_combphy_parse_dt(struct udevice *dev,return PTR_ERR (&priv->ref_clk); } - ret =reset_get_by_index (dev,0 , &priv->phy_rst); + ret =reset_get_bulk (dev, &priv->phy_rsts);if (ret) {dev_err (dev,"no phy reset control specified\n" );return ret;
PATCH v2 4/7 phy: rockchip: naneng-combphy: Support rk3588
In reply to Eugen HristevFrom: Jon Lin <[email protected]>
Add support for rk3588 phy variant.
The PHY clock is fixed at 100MHz.
---
Changes in v2:
- none
.../rockchip/phy-rockchip-naneng-combphy.c | 95 +++++++++++++++++++ 1 file changed, 95 insertions(+)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +95 -0
@@ -58,6 +58,7 @@ struct rockchip_combphy_grfcfg {struct combphy_reg con2_for_sata;struct combphy_reg con3_for_sata;struct combphy_reg pipe_con0_for_sata; +struct combphy_reg pipe_con1_for_sata;struct combphy_reg pipe_sgmii_mac_sel;struct combphy_reg pipe_xpcs_phy_ready;struct combphy_reg u3otg0_port_en;
@@ -423,11 +424,105 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = { .combphy_cfg = rk3568_combphy_cfg, }; +static int rk3588_combphy_cfg (struct rockchip_combphy_priv *priv) +{ +const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg; +u32 val; + +switch (priv->mode) { +case PHY_TYPE_PCIE : +param_write (priv->phy_grf, &cfg->con0_for_pcie, true); +param_write (priv->phy_grf, &cfg->con1_for_pcie, true); +param_write (priv->phy_grf, &cfg->con2_for_pcie, true); +param_write (priv->phy_grf, &cfg->con3_for_pcie, true); +break ; +case PHY_TYPE_USB3 : +param_write (priv->phy_grf, &cfg->pipe_txcomp_sel, false); +param_write (priv->phy_grf, &cfg->pipe_txelec_sel, false); +param_write (priv->phy_grf, &cfg->usb_mode_set, true); +break ; +case PHY_TYPE_SATA : +param_write (priv->phy_grf, &cfg->con0_for_sata, true); +param_write (priv->phy_grf, &cfg->con1_for_sata, true); +param_write (priv->phy_grf, &cfg->con2_for_sata, true); +param_write (priv->phy_grf, &cfg->con3_for_sata, true); +param_write (priv->pipe_grf, &cfg->pipe_con0_for_sata, true); +param_write (priv->pipe_grf, &cfg->pipe_con1_for_sata, true); +break ; +case PHY_TYPE_SGMII : +case PHY_TYPE_QSGMII : +default : +dev_err (priv->dev,"incompatible PHY type\n" ); +return -EINVAL ; + } + +/* 100MHz refclock signal is good */ +clk_set_rate (&priv->ref_clk,100000000 ); +param_write (priv->phy_grf, &cfg->pipe_clk_100m, true); +if (priv->mode ==PHY_TYPE_PCIE ) { +/* PLL KVCO tuning fine */ + val =readl (priv->mmio + (0x20 <<2 )); + val &= ~GENMASK (4 ,2 ); + val |=0x4 <<2 ; +writel (val, priv->mmio + (0x20 <<2 )); + +/* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */ + val =0x4c ; +writel (val, priv->mmio + (0x1b <<2 )); + +/* Set up su_trim: T3 */ + val =0xb0 ; +writel (val, priv->mmio + (0xa <<2 )); + val =0x47 ; +writel (val, priv->mmio + (0xb <<2 )); + val =0x57 ; +writel (val, priv->mmio + (0xd <<2 )); + } + +return 0 ; +} + +static const struct rockchip_combphy_grfcfg rk3588_combphy_grfcfgs = { +/* pipe-phy-grf */ + .pcie_mode_set = {0x0000 ,5 ,0 ,0x00 ,0x11 }, + .usb_mode_set = {0x0000 ,5 ,0 ,0x00 ,0x04 }, + .pipe_rxterm_set = {0x0000 ,12 ,12 ,0x00 ,0x01 }, + .pipe_txelec_set = {0x0004 ,1 ,1 ,0x00 ,0x01 }, + .pipe_txcomp_set = {0x0004 ,4 ,4 ,0x00 ,0x01 }, + .pipe_clk_25m = {0x0004 ,14 ,13 ,0x00 ,0x01 }, + .pipe_clk_100m = {0x0004 ,14 ,13 ,0x00 ,0x02 }, + .pipe_rxterm_sel = {0x0008 ,8 ,8 ,0x00 ,0x01 }, + .pipe_txelec_sel = {0x0008 ,12 ,12 ,0x00 ,0x01 }, + .pipe_txcomp_sel = {0x0008 ,15 ,15 ,0x00 ,0x01 }, + .pipe_clk_ext = {0x000c ,9 ,8 ,0x02 ,0x01 }, + .pipe_phy_status = {0x0034 ,6 ,6 ,0x01 ,0x00 }, + .con0_for_pcie = {0x0000 ,15 ,0 ,0x00 ,0x1000 }, + .con1_for_pcie = {0x0004 ,15 ,0 ,0x00 ,0x0000 }, + .con2_for_pcie = {0x0008 ,15 ,0 ,0x00 ,0x0101 }, + .con3_for_pcie = {0x000c ,15 ,0 ,0x00 ,0x0200 }, + .con0_for_sata = {0x0000 ,15 ,0 ,0x00 ,0x0129 }, + .con1_for_sata = {0x0004 ,15 ,0 ,0x00 ,0x0040 }, + .con2_for_sata = {0x0008 ,15 ,0 ,0x00 ,0x80c1 }, + .con3_for_sata = {0x000c ,15 ,0 ,0x00 ,0x0407 }, +/* pipe-grf */ + .pipe_con0_for_sata = {0x0000 ,11 ,5 ,0x00 ,0x22 }, + .pipe_con1_for_sata = {0x0000 ,2 ,0 ,0x00 ,0x2 }, +}; + +static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = { + .grfcfg = &rk3588_combphy_grfcfgs, + .combphy_cfg = rk3588_combphy_cfg, +}; +static const struct udevice_id rockchip_combphy_ids[] = { { .compatible ="rockchip,rk3568-naneng-combphy" , .data = (ulong)&rk3568_combphy_cfgs }, + { + .compatible ="rockchip,rk3588-naneng-combphy" , + .data = (ulong)&rk3588_combphy_cfgs + }, { } };
Signature · 1 line
2.34.1
Re: [PATCH v2 4/7] phy: rockchip: naneng-combphy: Support rk3588
Quoted 11 lines · Eugen Hristev
From: Jon Lin <[email protected]>
Add support for rk3588 phy variant.
The PHY clock is fixed at 100MHz.Signed-off-by Jon Lin <[email protected]>[[email protected]: update pcie pll parameters]Co-developed-by Kever Yang <[email protected]>Signed-off-by Kever Yang <[email protected]>[[email protected]: squashed, tidy up]Signed-off-by Eugen Hristev <[email protected]>
Thanks,
- Kever
Quoted 125 lines
---
Changes in v2:
- none.../rockchip/phy-rockchip-naneng-combphy.c | 95 +++++++++++++++++++ 1 file changed, 95 insertions(+)drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +95
-0@@ -58,6 +58,7 @@ struct rockchip_combphy_grfcfg {struct combphy_reg con2_for_sata;struct combphy_reg con3_for_sata;struct combphy_reg pipe_con0_for_sata; +struct combphy_reg pipe_con1_for_sata;struct combphy_reg pipe_sgmii_mac_sel;struct combphy_reg pipe_xpcs_phy_ready;struct combphy_reg u3otg0_port_en;@@ -423,11 +424,105 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = { .combphy_cfg = rk3568_combphy_cfg, }; +static int rk3588_combphy_cfg (struct rockchip_combphy_priv *priv) +{ +const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg; +u32 val; + +switch (priv->mode) { +case PHY_TYPE_PCIE : +param_write (priv->phy_grf, &cfg->con0_for_pcie, true); +param_write (priv->phy_grf, &cfg->con1_for_pcie, true); +param_write (priv->phy_grf, &cfg->con2_for_pcie, true); +param_write (priv->phy_grf, &cfg->con3_for_pcie, true); +break ; +case PHY_TYPE_USB3 : +param_write (priv->phy_grf, &cfg->pipe_txcomp_sel, false); +param_write (priv->phy_grf, &cfg->pipe_txelec_sel, false); +param_write (priv->phy_grf, &cfg->usb_mode_set, true); +break ; +case PHY_TYPE_SATA : +param_write (priv->phy_grf, &cfg->con0_for_sata, true); +param_write (priv->phy_grf, &cfg->con1_for_sata, true); +param_write (priv->phy_grf, &cfg->con2_for_sata, true); +param_write (priv->phy_grf, &cfg->con3_for_sata, true); +param_write (priv->pipe_grf, &cfg->pipe_con0_for_sata, true); +param_write (priv->pipe_grf, &cfg->pipe_con1_for_sata, true); +break ; +case PHY_TYPE_SGMII : +case PHY_TYPE_QSGMII : +default : +dev_err (priv->dev,"incompatible PHY type\n" ); +return -EINVAL ; + } + +/* 100MHz refclock signal is good */ +clk_set_rate (&priv->ref_clk,100000000 ); +param_write (priv->phy_grf, &cfg->pipe_clk_100m, true); +if (priv->mode ==PHY_TYPE_PCIE ) { +/* PLL KVCO tuning fine */ + val =readl (priv->mmio + (0x20 <<2 )); + val &= ~GENMASK (4 ,2 ); + val |=0x4 <<2 ; +writel (val, priv->mmio + (0x20 <<2 )); + +/* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */ + val =0x4c ; +writel (val, priv->mmio + (0x1b <<2 )); + +/* Set up su_trim: T3 */ + val =0xb0 ; +writel (val, priv->mmio + (0xa <<2 )); + val =0x47 ; +writel (val, priv->mmio + (0xb <<2 )); + val =0x57 ; +writel (val, priv->mmio + (0xd <<2 )); + } + +return 0 ; +} + +static const struct rockchip_combphy_grfcfg rk3588_combphy_grfcfgs = { +/* pipe-phy-grf */ + .pcie_mode_set = {0x0000 ,5 ,0 ,0x00 ,0x11 }, + .usb_mode_set = {0x0000 ,5 ,0 ,0x00 ,0x04 }, + .pipe_rxterm_set = {0x0000 ,12 ,12 ,0x00 ,0x01 }, + .pipe_txelec_set = {0x0004 ,1 ,1 ,0x00 ,0x01 }, + .pipe_txcomp_set = {0x0004 ,4 ,4 ,0x00 ,0x01 }, + .pipe_clk_25m = {0x0004 ,14 ,13 ,0x00 ,0x01 }, + .pipe_clk_100m = {0x0004 ,14 ,13 ,0x00 ,0x02 }, + .pipe_rxterm_sel = {0x0008 ,8 ,8 ,0x00 ,0x01 }, + .pipe_txelec_sel = {0x0008 ,12 ,12 ,0x00 ,0x01 }, + .pipe_txcomp_sel = {0x0008 ,15 ,15 ,0x00 ,0x01 }, + .pipe_clk_ext = {0x000c ,9 ,8 ,0x02 ,0x01 }, + .pipe_phy_status = {0x0034 ,6 ,6 ,0x01 ,0x00 }, + .con0_for_pcie = {0x0000 ,15 ,0 ,0x00 ,0x1000 }, + .con1_for_pcie = {0x0004 ,15 ,0 ,0x00 ,0x0000 }, + .con2_for_pcie = {0x0008 ,15 ,0 ,0x00 ,0x0101 }, + .con3_for_pcie = {0x000c ,15 ,0 ,0x00 ,0x0200 }, + .con0_for_sata = {0x0000 ,15 ,0 ,0x00 ,0x0129 }, + .con1_for_sata = {0x0004 ,15 ,0 ,0x00 ,0x0040 }, + .con2_for_sata = {0x0008 ,15 ,0 ,0x00 ,0x80c1 }, + .con3_for_sata = {0x000c ,15 ,0 ,0x00 ,0x0407 }, +/* pipe-grf */ + .pipe_con0_for_sata = {0x0000 ,11 ,5 ,0x00 ,0x22 }, + .pipe_con1_for_sata = {0x0000 ,2 ,0 ,0x00 ,0x2 }, +}; + +static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = { + .grfcfg = &rk3588_combphy_grfcfgs, + .combphy_cfg = rk3588_combphy_cfg, +}; +static const struct udevice_id rockchip_combphy_ids[] = { { .compatible ="rockchip,rk3568-naneng-combphy" , .data = (ulong)&rk3568_combphy_cfgs }, + { + .compatible ="rockchip,rk3588-naneng-combphy" , + .data = (ulong)&rk3588_combphy_cfgs + }, { } };
PATCH v2 5/7 ARM: dts: rockchip: rk3588s-u-boot: add pcie2x1l2 with PHY
In reply to Eugen HristevFrom: Joseph Chen <[email protected]>
Add the node for pciE 2x1l 2 device together with the corresponding combphy.
[[email protected]: moved to -u-boot.dtsi, minor adaptations]
---
Changes in v2:
- add compliance with linux by Jonas
arch/arm/dts/rk3588s-u-boot.dtsi | 77 ++++++++++++++++++++++++++++++++ 1 file changed, 77 insertions(+)
arch/arm/dts/rk3588s-u-boot.dtsi +77 -0
@@ -4,6 +4,7 @@ */ #include "rockchip-u-boot.dtsi" +#include <dt-bindings/phy/phy.h> / { dmc {
@@ -58,6 +59,11 @@ reg = <0x0 0xfd58a000 0x0 0x2000>; }; + pipe_phy0_grf: syscon@fd5bc000 { + compatible = "rockchip,pipe-phy-grf", "syscon"; + reg = <0x0 0xfd5bc000 0x0 0x100>; + }; + usb2phy2_grf: syscon@fd5d8000 { compatible = "rockchip,rk3588-usb2phy-grf", "syscon", "simple-mfd";
@@ -104,6 +110,61 @@ }; }; + pcie2x1l2: pcie@fe190000 { + compatible = "rockchip,rk3588-pcie", "snps,dw-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x40 0x4f>; + clocks = <&cru ACLK_PCIE_1L2_MSTR>, <&cru ACLK_PCIE_1L2_SLV>, + <&cru ACLK_PCIE_1L2_DBI>, <&cru PCLK_PCIE_1L2>, + <&cru CLK_PCIE_AUX4>, <&cru CLK_PCIE1L2_PIPE>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe"; + device_type = "pci"; + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie2x1l2_intc 0>, + <0 0 0 2 &pcie2x1l2_intc 1>, + <0 0 0 3 &pcie2x1l2_intc 2>, + <0 0 0 4 &pcie2x1l2_intc 3>; + linux,pci-domain = <4>; + num-ib-windows = <8>; + num-ob-windows = <8>; + num-viewport = <4>; + max-link-speed = <2>; + msi-map = <0x4000 &gic 0x4000 0x1000>; + num-lanes = <1>; + phys = <&combphy0_ps PHY_TYPE_PCIE>; + phy-names = "pcie-phy"; + power-domains = <&power RK3588_PD_PCIE>; + ranges = <0x01000000 0x0 0xf4100000 0x0 0xf4100000 0x0 0x00100000>, + <0x02000000 0x0 0xf4200000 0x0 0xf4200000 0x0 0x00e00000>, + <0x03000000 0x0 0x40000000 0xa 0x00000000 0x0 0x40000000>; + reg = <0xa 0x41000000 0x0 0x00400000>, + <0x0 0xfe190000 0x0 0x00010000>, + <0x0 0xf4000000 0x0 0x00100000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE4_POWER_UP>, <&cru SRST_P_PCIE4>; + reset-names = "pcie", "periph"; + rockchip,pipe-grf = <&php_grf>; + status = "disabled"; + + pcie2x1l2_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING 0>; + }; + }; + sfc: spi@fe2b0000 { compatible = "rockchip,sfc"; reg = <0x0 0xfe2b0000 0x0 0x4000>;
@@ -134,6 +195,22 @@ reg = <0x0 0xfe378000 0x0 0x200>; status = "disabled"; }; + + combphy0_ps: phy@fee00000 { + compatible = "rockchip,rk3588-naneng-combphy"; + reg = <0x0 0xfee00000 0x0 0x100>; + #phy-cells = <1>; + clocks = <&cru CLK_REF_PIPE_PHY0>, <&cru PCLK_PCIE_COMBO_PIPE_PHY0>, + <&cru PCLK_PHP_ROOT>; + clock-names = "refclk", "apbclk", "phpclk"; + assigned-clocks = <&cru CLK_REF_PIPE_PHY0>; + assigned-clock-rates = <100000000>; + resets = <&cru SRST_P_PCIE2_PHY0>, <&cru SRST_REF_PIPE_PHY0>; + reset-names = "combphy-apb", "combphy"; + rockchip,pipe-grf = <&php_grf>; + rockchip,pipe-phy-grf = <&pipe_phy0_grf>; + status = "disabled"; + }; }; &xin24m {
Signature · 1 line
2.34.1
Re: [PATCH v2 5/7] ARM: dts: rockchip: rk3588s-u-boot: add pcie2x1l2 with PHY
Hi Eugen,
Quoted 3 lines · Eugen Hristev
From: Joseph Chen <[email protected]>
Add the node for pciE 2x1l 2 device together with the corresponding
Typo "pciE" in the patch 5-7? We use 'PCIe' in term or 'pcie' in code.
Thanks,
- Kever
Quoted 124 lines
combphy.
Signed-off-by Joseph Chen <[email protected]>[[email protected]: moved to
-u-boot.dtsi, minor adaptations]Signed-off-by Eugen Hristev <[email protected]>[[email protected]: adapt to kernel node]Signed-off-by Jonas Karlman <[email protected]>---
Changes in v2:
- add compliance with linux by Jonasarch/arm/dts/rk3588s-u-boot.dtsi | 77 ++++++++++++++++++++++++++++++++ 1 file changed, 77 insertions(+)arch/arm/dts/rk3588s-u-boot.dtsi +77
-0@@ -4,6 +4,7 @@ */ #include "rockchip-u-boot.dtsi" +#include <dt-bindings/phy/phy.h> / { dmc {@@ -58,6 +59,11 @@ reg = <0x0 0xfd58a000 0x0 0x2000>; }; + pipe_phy0_grf: syscon@fd5bc000 { + compatible = "rockchip,pipe-phy-grf", "syscon"; + reg = <0x0 0xfd5bc000 0x0 0x100>; + }; + usb2phy2_grf: syscon@fd5d8000 { compatible = "rockchip,rk3588-usb2phy-grf", "syscon", "simple-mfd";@@ -104,6 +110,61 @@ }; }; + pcie2x1l2: pcie@fe190000 { + compatible = "rockchip,rk3588-pcie", "snps,dw-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x40 0x4f>; + clocks = <&cru ACLK_PCIE_1L2_MSTR>, <&cru ACLK_PCIE_1L2_SLV>, + <&cru ACLK_PCIE_1L2_DBI>, <&cru PCLK_PCIE_1L2>, + <&cru CLK_PCIE_AUX4>, <&cru CLK_PCIE1L2_PIPE>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe"; + device_type = "pci"; + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie2x1l2_intc 0>, + <0 0 0 2 &pcie2x1l2_intc 1>, + <0 0 0 3 &pcie2x1l2_intc 2>, + <0 0 0 4 &pcie2x1l2_intc 3>; + linux,pci-domain = <4>; + num-ib-windows = <8>; + num-ob-windows = <8>; + num-viewport = <4>; + max-link-speed = <2>; + msi-map = <0x4000 &gic 0x4000 0x1000>; + num-lanes = <1>; + phys = <&combphy0_ps PHY_TYPE_PCIE>; + phy-names = "pcie-phy"; + power-domains = <&power RK3588_PD_PCIE>; + ranges = <0x01000000 0x0 0xf4100000 0x0 0xf4100000 0x0 0x00100000>, + <0x02000000 0x0 0xf4200000 0x0 0xf4200000 0x0 0x00e00000>, + <0x03000000 0x0 0x40000000 0xa 0x00000000 0x0 0x40000000>; + reg = <0xa 0x41000000 0x0 0x00400000>, + <0x0 0xfe190000 0x0 0x00010000>, + <0x0 0xf4000000 0x0 0x00100000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE4_POWER_UP>, <&cru SRST_P_PCIE4>; + reset-names = "pcie", "periph"; + rockchip,pipe-grf = <&php_grf>; + status = "disabled"; + + pcie2x1l2_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING 0>; + }; + }; + sfc: spi@fe2b0000 { compatible = "rockchip,sfc"; reg = <0x0 0xfe2b0000 0x0 0x4000>;@@ -134,6 +195,22 @@ reg = <0x0 0xfe378000 0x0 0x200>; status = "disabled"; }; + + combphy0_ps: phy@fee00000 { + compatible = "rockchip,rk3588-naneng-combphy"; + reg = <0x0 0xfee00000 0x0 0x100>; + #phy-cells = <1>; + clocks = <&cru CLK_REF_PIPE_PHY0>, <&cru PCLK_PCIE_COMBO_PIPE_PHY0>, + <&cru PCLK_PHP_ROOT>; + clock-names = "refclk", "apbclk", "phpclk"; + assigned-clocks = <&cru CLK_REF_PIPE_PHY0>; + assigned-clock-rates = <100000000>; + resets = <&cru SRST_P_PCIE2_PHY0>, <&cru SRST_REF_PIPE_PHY0>; + reset-names = "combphy-apb", "combphy"; + rockchip,pipe-grf = <&php_grf>; + rockchip,pipe-phy-grf = <&pipe_phy0_grf>; + status = "disabled"; + }; }; &xin24m {
PATCH v2 6/7 ARM: dts: rockchip: rock5b: enable pcie2x1l2 and associated combphy
In reply to Eugen HristevFrom: Christopher Obbard <[email protected]>
Enable the pciE 2x1l 2 device and associated combphy. On this bus, the Rock5B has an Ethernet transceiver connected.
---
Changes in v2:
- add pcie2x1l2_pins by Jonas
arch/arm/dts/rk3588-rock-5b-u-boot.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
arch/arm/dts/rk3588-rock-5b-u-boot.dtsi +22 -0
@@ -30,13 +30,35 @@ }; }; +&combphy0_ps { + status = "okay"; +}; + &fspim2_pins { bootph-all; }; +&pcie2x1l2 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie2x1l2_pins &pcie_reset_h>; + reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + &pinctrl { bootph-all; + pcie { + pcie_reset_h: pcie-reset-h { + rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie2x1l2_pins: pcie2x1l2-pins { + rockchip,pins = <3 RK_PC7 4 &pcfg_pull_none>, + <3 RK_PD0 4 &pcfg_pull_none>; + }; + }; + usb { vcc5v0_host_en: vcc5v0-host-en { rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
Signature · 1 line
2.34.1
PATCH v2 7/7 configs: rock5b-rk3588: add pci drivers and command
In reply to Eugen HristevAdd drivers for pciE , phy, and command.
---
Changes in v2:
- binman_fdt is now removed
configs/rock5b-rk3588_defconfig | 4 ++++ 1 file changed, 4 insertions(+)
configs/rock5b-rk3588_defconfig +4 -0
@@ -47,6 +47,7 @@ CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y CONFIG_CMD_SPI=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
@@ -72,7 +73,10 @@ CONFIG_MMC_SDHCI_ROCKCHIP=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PCI=y +CONFIG_PCIE_DW_ROCKCHIP=y CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y CONFIG_SPL_PINCTRL=y CONFIG_REGULATOR_PWM=y CONFIG_DM_REGULATOR_FIXED=y
Signature · 1 line
2.34.1
Quoted 5 lines · Eugen Hristev
From: Jon Lin <[email protected]>
Add compatible for RK3588 SoC.
Signed-off-by Jon Lin <[email protected]>
Thanks,
- Kever
Quoted 19 lines
---
Changes in v2:
- nonedrivers/pci/pcie_dw_rockchip.c | 1 + 1 file changed, 1 insertion(+)drivers/pci/pcie_dw_rockchip.c +1
-0@@ -468,6 +468,7 @@ static const struct dm_pci_ops rockchip_pcie_ops = {static const struct udevice_id rockchip_pcie_ids[] = { { .compatible ="rockchip,rk3568-pcie" }, + { .compatible ="rockchip,rk3588-pcie" }, { } };