Skip to contentSkip to conversation

ACPI power-off doesn't work on Asus CUV4X (VIA Apollo 133)

DISCUSSION Alex Riesen 2 participants 3 messages Mar 24, 2001 – Mar 25, 2001

lore
Share & tools
lore
#0 lore raw

Hi, dear all

As i recompiled 2.4.2-ac20 with ACPI support the system cannot switch itself off. With APM it work without any problem.

I get a message "Couldn't switch to S5" if try to call reboot(2).
At load it shows that the mode is supported.

Alex Riesen

P.S.
Motheboard Asus CUV4X

/proc/cpuinfo:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 3
cpu MHz : 701.605
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1399.19

#1 lore raw
Quoted 3 lines · Alex Riesen

As i recompiled 2.4.2-ac20 with ACPI support the system cannot switch itself off. With APM it work without any problem.

APM doesn't work for me either.

Quoted 3 lines

I get a message "Couldn't switch to S5" if try to call reboot(2).
At load it shows that the mode is supported.

Same with AMR P6BAP-AP and P6VAP-AP () mainboards.

Firmware supports C2 C3 S0 S1 S4 S5.

All options for acpi tried.

#define APCI_DEBUG 1 has NO effect on verbosity of messages :-(

What should I do to get more debug info?

I'll try backing out all changes between 2.4.0 and 2.4.2-ac20, because there it worked ;-)

Regards

Ingo Oeser

cat /proc/cpuinfo
processor : 0
vendor_id : CentaurHauls
cpu family : 6
model : 6
model name : VIA Samuel
stepping : 0
cpu MHz : 501.155
cache size : 128 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu de tsc msr mce cx8 mtrr pge mmx 3dnow
bogomips : 999.42

Signature · 2 lines
10.+11.03.2001 - 3. Chemnitzer LinuxTag <http://www.tu-chemnitz.de/linux/tag>
         <<<<<<<<<<<<     been there and had much fun   >>>>>>>>>>>>
#2 lore raw
In reply to Alex Riesen
Quoted 9 lines · Ingo Oeser
Quoted 5 lines · Alex Riesen

As i recompiled 2.4.2-ac20 with ACPI support the system cannot switch itself off. I get a message "Couldn't switch to S5" if try to call reboot(2).
At load it shows that the mode is supported.

Same with AMR P6BAP-AP and P6VAP-AP () mainboards.

Quoted 7 lines

Firmware supports C2 C3 S0 S1 S4 S5.

All options for acpi tried.

#define APCI_DEBUG 1 has NO effect on verbosity of messages :-(

What should I do to get more debug info?

Just left it in FYI, Andrew.

Quoted 2 lines

I'll try backing out all changes between 2.4.0 and 2.4.2-ac20, because there it worked ;-)

Ok, that worked. Backing out all the changes made it shutdown again.

Since this shouldn't by the right way to fix this problem, what else can I do Andrew?

The BIG Problem is: This is an embedded machine, so I cannot attach all the funny debug tools. The most thing I can do is printk and evtl. ikdb. I have only 16MB flash disk on this machine and it is full already :-(

Regards

Ingo Oeser

Signature · 2 lines
10.+11.03.2001 - 3. Chemnitzer LinuxTag <http://www.tu-chemnitz.de/linux/tag>
         <<<<<<<<<<<<     been there and had much fun   >>>>>>>>>>>>