ACPI power-off doesn't work on Asus CUV4X (VIA Apollo 133)
Hi, dear all
As i recompiled 2.4.2-ac20 with ACPI support the system cannot switch itself off. With APM it work without any problem.
I get a message "Couldn't switch to S5" if try to call reboot(2).
At load it shows that the mode is supported.
Alex Riesen
P.S.
Motheboard Asus CUV4X
/proc/cpuinfo:
processor : 0vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 3
cpu MHz : 701.605
cache size : 256 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1399.19
Quoted 3 lines · Alex Riesen
As i recompiled 2.4.2-ac20 with ACPI support the system cannot switch itself off. With APM it work without any problem.
APM doesn't work for me either.
Quoted 3 lines
I get a message "Couldn't switch to S5" if try to call reboot(2).
At load it shows that the mode is supported.
Same with AMR P6BAP-AP and P6VAP-AP () mainboards.
Firmware supports C2 C3 S0 S1 S4 S5.
All options for acpi tried.
#define APCI_DEBUG 1 has NO effect on verbosity of messages :-(
What should I do to get more debug info?
I'll try backing out all changes between 2.4.0 and 2.4.2-ac20, because there it worked ;-)
Regards
Ingo Oeser
cat /proc/cpuinfo
processor : 0vendor_id : CentaurHauls
cpu family : 6
model : 6
model name : VIA Samuel
stepping : 0
cpu MHz : 501.155
cache size : 128 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu de tsc msr mce cx8 mtrr pge mmx 3dnow
bogomips : 999.42
Signature · 2 lines
10.+11.03.2001 - 3. Chemnitzer LinuxTag <http://www.tu-chemnitz.de/linux/tag>
<<<<<<<<<<<< been there and had much fun >>>>>>>>>>>>Quoted 9 lines · Ingo Oeser
Quoted 5 lines · Alex Riesen
As i recompiled 2.4.2-ac20 with ACPI support the system cannot switch itself off. I get a message "Couldn't switch to S5" if try to call reboot(2).
At load it shows that the mode is supported.Same with AMR P6BAP-AP and P6VAP-AP () mainboards.
Quoted 7 lines
Firmware supports C2 C3 S0 S1 S4 S5.
All options for acpi tried.
#define
APCI_DEBUG1 has NO effect on verbosity of messages :-(What should I do to get more debug info?
Just left it in FYI, Andrew.
Quoted 2 lines
I'll try backing out all changes between 2.4.0 and 2.4.2-ac20, because there it worked ;-)
Ok, that worked. Backing out all the changes made it shutdown again.
Since this shouldn't by the right way to fix this problem, what else can I do Andrew?
The BIG Problem is: This is an embedded machine, so I cannot attach all the funny debug tools. The most thing I can do is printk and evtl. ikdb. I have only 16MB flash disk on this machine and it is full already :-(
Regards
Ingo Oeser
Signature · 2 lines
10.+11.03.2001 - 3. Chemnitzer LinuxTag <http://www.tu-chemnitz.de/linux/tag>
<<<<<<<<<<<< been there and had much fun >>>>>>>>>>>>