Skip to contentSkip to conversation

Parallel Port doesn't detect EPP

DISCUSSION Udo A. Steinberg 3 participants 4 messages Sep 3, 2001

lore
Share & tools
lore
#0 lore raw

Hi,

I have just two questions regarding parallel port support with my Via686a chipset:

#1) EPP is no longer listed as supported transfer mode, but it used
to be.

#2) What is that "Can't probe parallel port" message?

Regards,
Udo.

PnPBIOS: Parport found PNPBIOS PNP0401 at io=0378,0778 irq=7 dma=3 0x378: FIFO is 16 bytes
0x378: writeIntrThreshold is 8
0x378: readIntrThreshold is 8
0x378: PWord is 8 bits
0x378: Interrupts are ISA-Pulses
0x378: ECP port cfgA=0x10 cfgB=0x00
0x378: ECP settings irq=<none or set by other means> dma=<none or set by other means>
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
parport0: cpp_daisy: aa5500ff(88)
parport0: assign_addrs: aa5500ff(88)
parport0: Printer, Hewlett-Packard HP LaserJet 6L
parport_pc: Strange, can't probe Via 686A parallel port: io=0x378, irq=7, dma=3

#1 lore raw
Quoted 2 lines · Udo A. Steinberg

#1) EPP is no longer listed as supported transfer mode, but it used
to be.

<rule_out_the_obvious>
Have you changed your BIOS setting since you last tried it? What does your BIOS say about your parallel port? </rule_out_the_obvious>

Tim.
*/

#2 lore raw
In reply to Udo A. Steinberg

Hi,

Quoted 5 lines · * On Mon, Sep 03, 2001 at 09:46 PM (+0200), Udo A. Steinberg wrote:

I have just two questions regarding parallel port support with my Via686a chipset:

#1) EPP is no longer listed as supported transfer mode, but it used
to be.

What's your BIOS setting for your parallel port?

I've got quite the same "problem" when setting it to "ECP+PPP". When configuring "EPP" mode it runs well (and my Iomega ZIP drive ("ppa") is able to use 32 bit mode) - I don't need "ECP" mode here.

My motherboard ist an "Epox 8kta+".

Regards,
Steffen

#3 lore raw
In reply to Udo A. Steinberg
Quoted 7 lines · Tim Waugh
Quoted 2 lines

#1) EPP is no longer listed as supported transfer mode, but it used
to be.

<rule_out_the_obvious>
Have you changed your BIOS setting since you last tried it? What does your BIOS say about your parallel port? </rule_out_the_obvious>

My BIOS setting has always been "ECP+EPP". After Steffen's mail regarding "ECP+EPP" I've changed my parport BIOS setting to "EPP" and using 2.4 I now get:

parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]

I also tried 2.2. with "ECP+EPP" and it detects both ECP and EPP:
[SPP,ECP,ECPEPP,ECPPS2]

Apparently 2.4. doesn't detect the parport settings the same way 2.2. does.

Regards,
Udo.