ramdisk initrd
Hello All,
I am sorry if I sound a bit repetitive but can anyone tell me what are the steps to be followed to load a ramdisk image into the target board RAM . What am I supposed to set for initrd to work? I was able to create the RAMDISK image with the scripts posted in this forum but I got a bit lost about the settings to be made to load the correct ramdisk image file into memory. I am using PPcboot1.0.5 and a RPXClassic board .
Thank you in advance,
Paulo Seleme Correa / ICN EN DEA
Telefone: +55 (41) 341-6311; Fax: +55 (41) 341-5594 [email protected] (GroupWise: OP7648) Siemens Ltda.
Rua Pedro Gusso, 2635 - CIC
81310-900 Curitiba - PR - Brasil
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Quoted 4 lines · In message <[email protected]> you wrote:
I am sorry if I sound a bit repetitive but can anyone tell me what are the steps to be followed to load a ramdisk image into the target board RAM . What am I supposed to set for initrd to work?
Did you RTFM? Really?
Quoted 4 lines
I was able to create the RAMDISK image with the scripts posted in this forum but I got a bit lost about the settings to be made to load the correct ramdisk image file into memory. I am using PPcboot1.0.5 and a RPXClassic board .
The PPCBoot "README" says:
...
Similar you can build PPCBoot images from a 'ramdisk.image.gz' file when your kernel is intended to use an initial ramdisk:
-> tools/mkimage -n 'Simple Ramdisk Image' \
> -A ppc -O linux -T ramdisk -C gzip \
> -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
Image Name: Simple Ramdisk Image
Created: Wed Jan 12 14:01:50 2000
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
Load Address: 0x00000000
Entry Point: 0x00000000...
If you want to boot a Linux kernel with initial ram disk, you pass the memory addreses of both the kernel and the initrd image (PPBCOOT format!) to the "bootm" command:
...
=> bootm 40100000 40200000
## Booting Linux kernel at 40100000 ...
Image Name: 2.2.13 for initrd on TQM850L
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 335725 Bytes = 327 kB = 0 MB
Load Address: 00000000
Entry Point: 0000000c
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 40200000 ...
Image Name: Simple Ramdisk Image
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 566530 Bytes = 553 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk ... OK
Linux version 2.2.13 ([email protected]) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000...
Can you please explain which parts of this description you don't understand?
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] Nothing is easier than to denounce the evildoer; nothing is more
difficult than to understand him. - Fyodor Dostoevski
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/