Skip to contentSkip to conversation

ramdisk initrd

DISCUSSION PAULO SELEME CORREA PAULO 2 participants 2 messages Oct 18, 2001

lore
Share & tools
lore
#0 lore raw

Hello All,

I am sorry if I sound a bit repetitive but can anyone tell me what are the steps to be followed to load a ramdisk image into the target board RAM . What am I supposed to set for initrd to work? I was able to create the RAMDISK image with the scripts posted in this forum but I got a bit lost about the settings to be made to load the correct ramdisk image file into memory. I am using PPcboot1.0.5 and a RPXClassic board .

Thank you in advance,

Paulo Seleme Correa / ICN EN DEA
Telefone: +55 (41) 341-6311; Fax: +55 (41) 341-5594 [email protected] (GroupWise: OP7648) Siemens Ltda.
Rua Pedro Gusso, 2635 - CIC
81310-900 Curitiba - PR - Brasil

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw
Quoted 4 lines · In message <[email protected]> you wrote:

I am sorry if I sound a bit repetitive but can anyone tell me what are the steps to be followed to load a ramdisk image into the target board RAM . What am I supposed to set for initrd to work?

Did you RTFM? Really?

Quoted 4 lines

I was able to create the RAMDISK image with the scripts posted in this forum but I got a bit lost about the settings to be made to load the correct ramdisk image file into memory. I am using PPcboot1.0.5 and a RPXClassic board .

The PPCBoot "README" says:

...
Similar you can build PPCBoot images from a 'ramdisk.image.gz' file when your kernel is intended to use an initial ramdisk:

        -> tools/mkimage -n 'Simple Ramdisk Image' \
        > -A ppc -O linux -T ramdisk -C gzip \
        > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
        Image Name:   Simple Ramdisk Image
        Created:      Wed Jan 12 14:01:50 2000
        Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
        Data Size:    566530 Bytes = 553.25 kB = 0.54 MB
        Load Address: 0x00000000
        Entry Point:  0x00000000

...
If you want to boot a Linux kernel with initial ram disk, you pass the memory addreses of both the kernel and the initrd image (PPBCOOT format!) to the "bootm" command:
...

        => bootm 40100000 40200000
        ## Booting Linux kernel at 40100000 ...
           Image Name:   2.2.13 for initrd on TQM850L
           Image Type:   PowerPC Linux Kernel Image (gzip compressed)
           Data Size:    335725 Bytes = 327 kB = 0 MB
           Load Address: 00000000
           Entry Point:  0000000c
           Verifying Checksum ... OK
           Uncompressing Kernel Image ... OK
        ## Loading RAMDisk Image at 40200000 ...
           Image Name:   Simple Ramdisk Image
           Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
           Data Size:    566530 Bytes = 553 kB = 0 MB
           Load Address: 00000000
           Entry Point:  00000000
           Verifying Checksum ... OK
           Loading Ramdisk ... OK
        Linux version 2.2.13 ([email protected]) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000

...

Can you please explain which parts of this description you don't understand?

Wolfgang Denk

--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] Nothing is easier than to denounce the evildoer; nothing is more
difficult than to understand him. - Fyodor Dostoevski

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/