Skip to contentSkip to conversation

Simple ALSA capture/playback example and help wanted

DISCUSSION Howard Abrams 2 participants 5 messages Mar 29, 2002

lore
Share & tools
lore
#0 lore raw

All,

I'm new to ALSA, and I'm using whatever version is in the 2.5.7 kernel w/ a Midiman Dio 2448 (cmipci driver).

I'm trying to write a simple app that reads some samples, does a small bit of processing, and writes them back out to the same device.

The card is full duplex, but I cannot seem to open a pcm device for reading and writing at the same time. Even the "latency.c" doesn't work. Is the driver just broke?

Two questions:

1. What is the best way to accomplish my task?

2. Does anyone have a simple example to do this?

Thanks,

h.

#1 lore raw

There are several examples, but out of hubris I'll point you to my webpage: (all the examples are linked from the top)

http://mlug.missouri.edu/~markrages/wiki/index.php?WritingAnAlsaClient

In particular, I'd recommend you jook at JACK (jackit.sourceforge.net) before worrying too much about the ALSA details.

Regards,
Mark
[email protected]

Quoted 29 lines

All,

I'm new to ALSA, and I'm using whatever version is in the 2.5.7 kernel w/ a Midiman Dio 2448 (cmipci driver).

I'm trying to write a simple app that reads some samples, does a small bit of processing, and writes them back out to the same device.

The card is full duplex, but I cannot seem to open a pcm device for reading and writing at the same time. Even the "latency.c" doesn't work. Is the driver just broke?

Two questions:

1. What is the best way to accomplish my task?

2. Does anyone have a simple example to do this?

Thanks,

h.

_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel

#2 lore raw

Thanks Mark. I'll take a look at jack, but in the near-term, I copied a sample from a link off your page. It must have been from a earlier rev of the api, but it only required very minimal changes to compile.

The program I used was "A Minimal Full-Duplex Program", off the
page: http://www.op.net/~pbd/alsa-audio.html#duplexex

It's real basic, similar to what I had tried before. However, if I using the 'spdif' device I run into the same problem:

ALSA lib setup.c:94:(snd_sctl_install) Cannot lock ctl elem
duplex: pcm.c:847: snd_pcm_prepare: Assertion `pcm->setup' failed.

If I use the 'plughw:0,2' device, the program returns immediately, unless there is no audio on the spdif line, in which case it hangs.

To me, it looks like the driver has a problem with full-duplex. Is that correct? Again I'm using a Midiman DiO 2448 (cmipci driver).

Thanks again,

h.

Quoted 47 lines · Mark Rages

There are several examples, but out of hubris I'll point you to my webpage: (all the examples are linked from the top)

http://mlug.missouri.edu/~markrages/wiki/index.php?WritingAnAlsaClient

In particular, I'd recommend you jook at JACK (jackit.sourceforge.net) before worrying too much about the ALSA details.

Regards,
Mark
[email protected]

Quoted 21 lines

All,

I'm new to ALSA, and I'm using whatever version is in the 2.5.7 kernel w/ a Midiman Dio 2448 (cmipci driver).

I'm trying to write a simple app that reads some samples, does a small bit of processing, and writes them back out to the same device.

The card is full duplex, but I cannot seem to open a pcm device for reading and writing at the same time. Even the "latency.c" doesn't work. Is the driver just broke?

Two questions:

1. What is the best way to accomplish my task?

2. Does anyone have a simple example to do this?

Thanks,

Quoted 8 lines

h.

_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel

_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel

#3 lore raw
Quoted 7 lines · Howard Abrams

Thanks Mark. I'll take a look at jack, but in the near-term, I copied a sample from a link off your page. It must have been from a earlier rev of the api, but it only required very minimal changes to compile.

The program I used was "A Minimal Full-Duplex Program", off the
page: http://www.op.net/~pbd/alsa-audio.html#duplexex

Can you tell us what changes were required? It will help improve the documentation.

Sorry, I don't have the expertise (or the appropriate soundcard) to help with your specific problem.

Regards,
Mark.

#4 lore raw
Quoted 7 lines · Mark Rages
Quoted 5 lines · Howard Abrams

Thanks Mark. I'll take a look at jack, but in the near-term, I copied a sample from a link off your page. It must have been from a earlier rev of the api, but it only required very minimal changes to compile.

Quoted 6 lines
Quoted 3 lines

The program I used was "A Minimal Full-Duplex Program", off the
page: http://www.op.net/~pbd/alsa-audio.html#duplexex

Can you tell us what changes were required? It will help improve the documentation.

Sure, a diff is attached.

Quoted 3 lines

Sorry, I don't have the expertise (or the appropriate soundcard) to help with your specific problem.

Is Takashi Iwai on this list? He's credited in the source for the driver. Anyone else have one of these cards?

h.

12c10
< if ((snd_pcm_open ( &playback_handle, argv[1], SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
---

Quoted 1 line
         if ((playback_handle = snd_pcm_open (argv[1], SND_PCM_STREAM_PLAYBACK, 0)) < 0) {

17c15
< if ((snd_pcm_open ( &capture_handle, argv[1], SND_PCM_STREAM_CAPTURE, 0)) < 0) {
---

Quoted 1 line
         if ((capture_handle = snd_pcm_open (argv[1], SND_PCM_STREAM_CAPTURE, 0)) < 0) {

27c25
< snd_pcm_hw_params_set_rate_near (playback_handle, hw_params, 44100, 0);
---

Quoted 1 line
         snd_pcm_hw_params_set_rate_near (playback_handle, hw_params, 44100);

35c33
< snd_pcm_hw_params_set_rate_near (capture_handle, hw_params, 44100, 0);
---

Quoted 1 line
         snd_pcm_hw_params_set_rate_near (capture_handle, hw_params, 44100);

45,46c43,44
< snd_pcm_writei (playback_handle, pbuf, sizeof (pbuf));
< snd_pcm_readi (capture_handle, cbuf, sizeof (cbuf));
---

Quoted 2 lines
                 snd_pcm_write (playback_handle, pbuf, sizeof (pbuf));
                 snd_pcm_read (capture_handle, cbuf, sizeof (cbuf));