Simple ALSA capture/playback example and help wanted
All,
I'm new to ALSA, and I'm using whatever version is in the 2.5.7 kernel w/ a Midiman Dio 2448 (cmipci driver).
I'm trying to write a simple app that reads some samples, does a small bit of processing, and writes them back out to the same device.
The card is full duplex, but I cannot seem to open a pcm device for reading and writing at the same time. Even the "latency.c" doesn't work. Is the driver just broke?
Two questions:
1. What is the best way to accomplish my task?
2. Does anyone have a simple example to do this?
Thanks,
h.
There are several examples, but out of hubris I'll point you to my webpage: (all the examples are linked from the top)
http://mlug.missouri.edu/~markrages/wiki/index.php?WritingAnAlsaClient
In particular, I'd recommend you jook at JACK (jackit.sourceforge.net) before worrying too much about the ALSA details.
Regards,
Mark
[email protected]
Quoted 29 lines
All,
I'm new to ALSA, and I'm using whatever version is in the 2.5.7 kernel w/ a Midiman Dio 2448 (cmipci driver).
I'm trying to write a simple app that reads some samples, does a small bit of processing, and writes them back out to the same device.
The card is full duplex, but I cannot seem to open a pcm device for reading and writing at the same time. Even the "
latency.c" doesn't work. Is the driver just broke?Two questions:
1. What is the best way to accomplish my task?
2. Does anyone have a simple example to do this?
Thanks,
h.
_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
Thanks Mark. I'll take a look at jack, but in the near-term, I copied a sample from a link off your page. It must have been from a earlier rev of the api, but it only required very minimal changes to compile.
The program I used was "A Minimal Full-Duplex Program", off the
page: http://www.op.net/~pbd/alsa-audio.html#duplexex
It's real basic, similar to what I had tried before. However, if I using the 'spdif' device I run into the same problem:
ALSA lib setup.c:94:(snd_sctl_install) Cannot lock ctl elem
duplex: pcm.c:847: snd_pcm_prepare: Assertion `pcm->setup' failed.
If I use the 'plughw:0,2' device, the program returns immediately, unless there is no audio on the spdif line, in which case it hangs.
To me, it looks like the driver has a problem with full-duplex. Is that correct? Again I'm using a Midiman DiO 2448 (cmipci driver).
Thanks again,
h.
Quoted 47 lines · Mark Rages
There are several examples, but out of hubris I'll point you to my webpage: (all the examples are linked from the top)
http://mlug.missouri.edu/~markrages/wiki/index.php?WritingAnAlsaClient
In particular, I'd recommend you jook at JACK (jackit.sourceforge.net) before worrying too much about the ALSA details.
Regards,
Mark
[email protected]Quoted 21 lines
All,
I'm new to ALSA, and I'm using whatever version is in the 2.5.7 kernel w/ a Midiman Dio 2448 (cmipci driver).
I'm trying to write a simple app that reads some samples, does a small bit of processing, and writes them back out to the same device.
The card is full duplex, but I cannot seem to open a pcm device for reading and writing at the same time. Even the "
latency.c" doesn't work. Is the driver just broke?Two questions:
1. What is the best way to accomplish my task?
2. Does anyone have a simple example to do this?
Thanks,
Quoted 8 lines
h.
_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
Quoted 7 lines · Howard Abrams
Thanks Mark. I'll take a look at jack, but in the near-term, I copied a sample from a link off your page. It must have been from a earlier rev of the api, but it only required very minimal changes to compile.
The program I used was "A Minimal Full-Duplex Program", off the
page: http://www.op.net/~pbd/alsa-audio.html#duplexex
Can you tell us what changes were required? It will help improve the documentation.
Sorry, I don't have the expertise (or the appropriate soundcard) to help with your specific problem.
Regards,
Mark.
Quoted 7 lines · Mark Rages
Quoted 5 lines · Howard Abrams
Thanks Mark. I'll take a look at jack, but in the near-term, I copied a sample from a link off your page. It must have been from a earlier rev of the api, but it only required very minimal changes to compile.
Quoted 6 lines
Quoted 3 lines
The program I used was "A Minimal Full-Duplex Program", off the
page: http://www.op.net/~pbd/alsa-audio.html#duplexexCan you tell us what changes were required? It will help improve the documentation.
Sure, a diff is attached.
Quoted 3 lines
Sorry, I don't have the expertise (or the appropriate soundcard) to help with your specific problem.
Is Takashi Iwai on this list? He's credited in the source for the driver. Anyone else have one of these cards?
h.
12c10
< if ((snd_pcm_open ( &playback_handle, argv[1], SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
---
Quoted 1 line
if ((playback_handle = snd_pcm_open (argv[1], SND_PCM_STREAM_PLAYBACK, 0)) < 0) {17c15
< if ((snd_pcm_open ( &capture_handle, argv[1], SND_PCM_STREAM_CAPTURE, 0)) < 0) {
---
Quoted 1 line
if ((capture_handle = snd_pcm_open (argv[1], SND_PCM_STREAM_CAPTURE, 0)) < 0) {27c25
< snd_pcm_hw_params_set_rate_near (playback_handle, hw_params, 44100, 0);
---
Quoted 1 line
snd_pcm_hw_params_set_rate_near (playback_handle, hw_params, 44100);
35c33
< snd_pcm_hw_params_set_rate_near (capture_handle, hw_params, 44100, 0);
---
Quoted 1 line
snd_pcm_hw_params_set_rate_near (capture_handle, hw_params, 44100);
45,46c43,44
< snd_pcm_writei (playback_handle, pbuf, sizeof (pbuf));
< snd_pcm_readi (capture_handle, cbuf, sizeof (cbuf));
---
Quoted 2 lines
snd_pcm_write (playback_handle, pbuf, sizeof (pbuf));
snd_pcm_read (capture_handle, cbuf, sizeof (cbuf));