Skip to contentSkip to conversation

PROBLEM: Kernel 2.4.19 does not export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations

PATCH Phil Stracchino 5 participants 12 messages Sep 4, 2002 – Sep 12, 2002

lore
Share & tools
lore
#0 lore raw

PROBLEM SUMMARY:
Kernel 2.4.19 apparently fails to export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations

While trying to isolate an apparent progressive hardware failure, I had cause to swap the disks and SCSI controller from a K6-III/450 machine running kernel 2.4.19 into an Athlon/1200 machine. Having done so, I rebuilt the kernel with Athlon optimizations instead of K6-III.

Despite making no other change in the kernel configuration, this yielded an unusable kernel. The machine would boot, but almost all modules failed to load and the system as a whole was not usable running on that kernel. All failures appeared to come down to a single error, reporting _mmx_memcpy as an unresolved symbol. It appears that for some reason _mmx_memcpy is not exported from the kernel if Athlon optimization is used.

The system was sufficiently non-functional that I was unable to capture a log of the error messages.

Being of a suspicious nature, I generated .config files for K6 and Athlon optimizations, and discovered the following:

.config Wed Sep 4 13:59:39 2002 renamed from .config.k6 Wed Sep 4 01:22:11 2002 +6 -4
@@ -29,8 +29,8 @@
 # CONFIG_M686 is not set
 # CONFIG_MPENTIUMIII is not set
 # CONFIG_MPENTIUM4 is not set
-CONFIG_MK6=y
-# CONFIG_MK7 is not set
+# CONFIG_MK6 is not set
+CONFIG_MK7=y
 # CONFIG_MELAN is not set
 # CONFIG_MCRUSOE is not set
 # CONFIG_MWINCHIPC6 is not set
@@ -45,9 +45,11 @@
 CONFIG_X86_POPAD_OK=y
 # CONFIG_RWSEM_GENERIC_SPINLOCK is not set
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_X86_L1_CACHE_SHIFT=5
-CONFIG_X86_ALIGNMENT_16=y
+CONFIG_X86_L1_CACHE_SHIFT=6
 CONFIG_X86_TSC=y
+CONFIG_X86_GOOD_APIC=y
+CONFIG_X86_USE_3DNOW=y
+CONFIG_X86_PGE=y
 CONFIG_X86_USE_PPRO_CHECKSUM=y
 CONFIG_X86_MCE=y
 # CONFIG_TOSHIBA is not set

The significant thing here seems to be that CONFIG_X86_USE_3DNOW is not enabled when compiling for K6, because K6, K6-II and K6-III are treated as the same processor, even though the K6-III does in fact support 3DNow. I was baffled as to why 3DNow code would work with K6 optimizations but not with Athlon, but now I see that the explanation of that particular puzzle is that it wasn't being usedd on K6. I'm minded to try building a K6-optimized kernel with CONFIG_X86_USE_3DNOW turned on, but I don't have the results of that experiment yet and will report on it when I do.

ver_linux output:

/*
* scripts/ver_linux doesn't report the binutils
* version, an omission that should be remedied.
* the following simple change would accomplish
* this, as well as improving readability of the
* output:

ver_linux Wed Sep 4 13:51:32 2002 renamed from ver_linux.orig Sun Sep 2 10:27:18 2001 +2 -1
@@ -12,7 +12,8 @@
 uname -a
 echo ' '
 
-echo "Gnu C                 " `gcc --version`
+echo "Gnu C                 " `gcc --version | head -1`
+echo "Binutils (from ld)    " `ld --version | head -1`
 
 make --version 2>&1 | awk -F, '{print $1}' | awk \
       '/GNU Make/{print "Gnu make              ",$NF}'
	 *	The following output is as patched:
         */

Linux babylon5 2.4.19 #7 Wed Sep 4 00:32:43 EDT 2002 i686 unknown

Gnu C                  gcc (GCC) 3.2
Binutils (from ld)     GNU ld version 2.12
Gnu make               3.79.1
util-linux             2.11f
mount                  2.11f
modutils               2.4.6
e2fsprogs              1.25
reiserfsprogs          3.x.0b
PPP                    2.4.0b4
Linux C Library        2.1.3
Dynamic linker (ldd)   2.1.3
Linux C++ Library      5.0.0
Procps                 2.0.2
Net-tools              1.60
Kbd                    0.99
Sh-utils               1.16
Modules Loaded         ppp_deflate bsd_comp ppp_async ppp_generic slhc

audiopci pnp soundbase sndshield serial nfs lockd sunrpc iptable_filter ipt_MASQUERADE ip_nat_irc ip_conntrack_irc iptable_nat ip_tables mousedev hid input usb-uhci usbcore st sg lp parport_pc parport isofs inflate_fs sr_mod cdrom

binutils 2.12
/*
* scripts/ver_linux doesn't report the binutils
* version, an omission that should be remedied.
* the following one-line patch would accomplish
* this, as well as improving readability:

*** scripts/ver_linux.orig Sun Sep 2 10:27:18 2001
--- scripts/ver_linux Wed Sep 4 13:51:32 2002
***************
*** 12,18 ****
uname -a
echo ' '

! echo "Gnu C " gcc --version

make --version 2>&1 | awk -F, '{print $1}' | awk \
'/GNU Make/{print "Gnu make ",$NF}'
--- 12,19 ----
uname -a
echo ' '

! echo "Gnu C " gcc --version | head -1
! echo "Binutils (from ld) " ld --version | head -1

  make --version 2>&1 | awk -F, '{print $1}' | awk \
        '/GNU Make/{print "Gnu make              ",$NF}'
	 */

/proc/cpuinfo:

processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 4
model name : AMD Athlon(tm) Processor
stepping : 4
cpu MHz : 1200.097
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
bogomips : 2392.06

/proc/ioports:

0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
02f8-02ff : serial(auto)
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-40ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] 5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] 6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] c000-cfff : PCI Bus #01
c000-c0ff : 3Dfx Interactive, Inc. Voodoo 3
d000-d00f : VIA Technologies, Inc. Bus Master IDE d400-d41f : VIA Technologies, Inc. UHCI USB
d400-d41f : usb-uhci
d800-d81f : VIA Technologies, Inc. UHCI USB (#2)
d800-d81f : usb-uhci
dc00-dc3f : Ensoniq ES1370 [AudioPCI]
dc00-dc3f : AudioPCI
e000-e07f : 3Com Corporation 3c905B 100BaseTX [Cyclone]
e000-e07f : 00:09.0
e400-e403 : BusLogic BT-946C (BA80C30) [MultiMaster 10]
e400-e403 : BusLogic BT-958

/proc/iomem:

00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000cffff : Extension ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
00100000-002098c6 : Kernel code
002098c7-0027953f : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage 0fff3000-0fffffff : ACPI Tables
d0000000-d3ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133] d4000000-d7ffffff : PCI Bus #01
d4000000-d5ffffff : 3Dfx Interactive, Inc. Voodoo 3
d8000000-d9ffffff : PCI Bus #01
d8000000-d9ffffff : 3Dfx Interactive, Inc. Voodoo 3
db000000-db00007f : 3Com Corporation 3c905B 100BaseTX [Cyclone] db001000-db001fff : BusLogic BT-946C (BA80C30) [MultiMaster 10] ffff0000-ffffffff : reserved

/proc/modules:

ppp_deflate            39584   0 (autoclean)
bsd_comp                4288   0 (autoclean)
ppp_async               7504   1 (autoclean)
ppp_generic            15520   3 (autoclean) [ppp_deflate bsd_comp
ppp_async]
slhc                    4960   1 (autoclean) [ppp_generic]
audiopci               16768   0
pnp                    49904   0 [audiopci]
soundbase             846480   0 [audiopci pnp]
sndshield              11488   0 [audiopci pnp soundbase]
serial                 45920   2 (autoclean)
nfs                    66608   7 (autoclean)
lockd                  46640   1 (autoclean) [nfs]
sunrpc                 59552   1 (autoclean) [nfs lockd]
iptable_filter          1680   0 (autoclean) (unused)
ipt_MASQUERADE          1824   2 (autoclean)
ip_nat_irc              2976   0 (unused)
ip_conntrack_irc        2704   0 [ip_nat_irc]
iptable_nat            20096   9 [ipt_MASQUERADE ip_nat_irc]
ip_tables              14048   5 [iptable_filter ipt_MASQUERADE
iptable_nat]
mousedev                4128   1
hid                    18640   0 (unused)
input                   3456   0 [mousedev hid]
usb-uhci               21808   0 (unused)
usbcore                63872   1 [hid usb-uhci]
st                     26544   0 (unused)
sg                     31344   0 (unused)
lp                      6432   0 (unused)
parport_pc             21952   1
parport                25024   1 [lp parport_pc]
isofs                  25280   1 (autoclean)
inflate_fs             17760   0 (autoclean) [isofs]
sr_mod                 13280   0 (autoclean) (unused)
cdrom                  26592   0 (autoclean) [sr_mod]

lspci:

00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0305 (rev
02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: <available only to root>

00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8305
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d4000000-d7ffffff
Prefetchable memory behind bridge: d8000000-d9ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:07.0 ISA bridge: VIA Technologies, Inc.: Unknown device 0686 (rev 22)
Subsystem: Unknown device 1106:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
10) (prog-if 8a)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at d000
Capabilities: <available only to root>

00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d400
Capabilities: <available only to root>

00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d800
Capabilities: <available only to root>

00:07.4 Host bridge: VIA Technologies, Inc.: Unknown device 3057 (rev
30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: <available only to root>

00:08.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI] (rev 01)
Subsystem: Unknown device 4942:4c4c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 12 min, 128 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00

00:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: Unknown device 10b7:9055
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 10 min, 10 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e000
Region 1: Memory at db000000 (32-bit, non-prefetchable)
Capabilities: <available only to root>

00:0c.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10] (rev 08)
Subsystem: Unknown device 104b:1040
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 8 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e400
Region 1: Memory at db001000 (32-bit, non-prefetchable)

01:00.0 VGA compatible controller: 3Dfx Interactive, Inc.: Unknown device 0005 (rev 01)
Subsystem: Unknown device 121a:0030
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 14
Region 0: Memory at d4000000 (32-bit, non-prefetchable) Region 1: Memory at d8000000 (32-bit, prefetchable) Region 2: I/O ports at c000
Capabilities: <available only to root>

/proc/scsi/scsi:

Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DDYS-T18350N Rev: S96H
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: DNES-318350W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03

Signature · 5 lines
  *********  Fight Back!  It may not be just YOUR life at risk.  *********
  phil stracchino   ::   [email protected]   ::   [email protected]
    unix ronin     ::::   renaissance man   ::::   mystic zen biker geek
     2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold)
       Linux Now! ...because friends don't let friends use Microsoft.
#1 lore raw

FOLLOWUP: Kernel 2.4.19 does not export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations

FOLLOWUP:
I built a K6-optimized kernel and manually turned on CONFIG_X86_USE_3DNOW before beginning compilation, installed the kernel, and ran depmod -a. The result:

babylon5:root:/usr/src/linux-2.4.19:65 # depmod -a
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/block/rd.o
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/cdrom/cdrom.o
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/char/serial.o
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/ide/ide-cd.o
...
...
... well, you get the idea. A total of 40 modules fail, all with the same error. The following is the list of failed modules:

drivers/block/rd.o
drivers/cdrom/cdrom.o
drivers/char/serial.o
drivers/ide/ide-cd.o
drivers/md/lvm-mod.o
drivers/md/raid5.o
drivers/net/ppp_async.o
drivers/net/ppp_deflate.o
drivers/net/ppp_generic.o
drivers/net/slhc.o
drivers/net/slip.o
drivers/parport/parport.o
drivers/parport/parport_pc.o
drivers/pcmcia/pcmcia_core.o
drivers/scsi/aic7xxx/aic7xxx.o
drivers/scsi/ide-scsi.o
drivers/scsi/sg.o
drivers/scsi/sr_mod.o
drivers/scsi/st.o
drivers/usb/hid.o
drivers/usb/storage/usb-storage.o
drivers/usb/usb-uhci.o
drivers/usb/usbcore.o
fs/fat/fat.o
fs/inflate_fs/inflate_fs.o
fs/intermezzo/intermezzo.o
fs/isofs/isofs.o
fs/lockd/lockd.o
fs/minix/minix.o
fs/nfs/nfs.o
fs/nfsd/nfsd.o
fs/reiserfs/reiserfs.o
fs/smbfs/smbfs.o
fs/udf/udf.o
fs/ufs/ufs.o
fs/vfat/vfat.o
net/ipv4/netfilter/ip_tables.o
net/ipv4/netfilter/ipt_REJECT.o
net/ipv4/netfilter/iptable_nat.o
net/sunrpc/sunrpc.o

So it definitely looks like something is unhappy with CONFIG_X86_USE_3DNOW, possibly only when compiled with gcc-3.2, possibly not. Why it's not being exported, I have no idea; as far as I can tell, it should be.

I haven't tried building an Athlon-optimized kernel *without* using CONFIG_X86_USE_3DNOW.

Signature · 5 lines
  *********  Fight Back!  It may not be just YOUR life at risk.  *********
  phil stracchino   ::   [email protected]   ::   [email protected]
    unix ronin     ::::   renaissance man   ::::   mystic zen biker geek
     2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold)
       Linux Now! ...because friends don't let friends use Microsoft.
#2 lore raw
In reply to Phil Stracchino
Quoted 3 lines · Phil Stracchino

PROBLEM SUMMARY:
Kernel 2.4.19 apparently fails to export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations

You need to save your .config make distclean, restore it make oldconfig dep and build the kernel. Its a known limitation in the CML1 config tools

#3 lore raw
Quoted 8 lines · Alan Cox
Quoted 3 lines · Phil Stracchino

PROBLEM SUMMARY:
Kernel 2.4.19 apparently fails to export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations

You need to save your .config make distclean, restore it make oldconfig dep and build the kernel. Its a known limitation in the CML1 config tools

Aha, so it's a known config problem, not bizarre psychic terrorism on the part of the source code. Thank you for saving my sanity. :) I'll give that procedure a shot.

Signature · 5 lines
  *********  Fight Back!  It may not be just YOUR life at risk.  *********
  phil stracchino   ::   [email protected]   ::   [email protected]
    unix ronin     ::::   renaissance man   ::::   mystic zen biker geek
     2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold)
       Linux Now! ...because friends don't let friends use Microsoft.
#4 lore raw

CDROM driver does not support Linux partition tables

In reply to Alan Cox

A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.

Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?

(The particular case in which this came up is someone who has a Sun box without a CDROM drive in it, and wants to use a Linux box as a jumpstart server, but can't because the Linux box can't read beyond the first slice on the CD.)

Signature · 5 lines
 *********  Fight Back!  It may not be just YOUR life at risk.  *********
 :phil stracchino : unix ronin : renaissance man : mystic zen biker geek:
 : [email protected]   :::   [email protected]   :::    [email protected] :
 :  2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold)  :
 :    Linux Now! ...because friends don't let friends use Microsoft.    :
#5 lore raw

Re: CDROM driver does not support Linux partition tables

Quoted 8 lines · Phil Stracchino

A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.

Quoted 4 lines

Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?

It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.

#6 lore raw

Re: CDROM driver does not support Linux partition tables

Quoted 9 lines · Alan Cox
Quoted 8 lines · Phil Stracchino

A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.

Quoted 7 lines
Quoted 4 lines

Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?

It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.

The opposite, surely? sr uses one minor per cd-rom, ide-cd has 64.

Signature · 1 line
Jens Axboe
#7 lore raw

Re: CDROM driver does not support Linux partition tables

Quoted 4 lines · Jens Axboe
Quoted 2 lines

It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.

The opposite, surely? sr uses one minor per cd-rom, ide-cd has 64.

Brain on stun. Yes ide-scsi is a problem ide-cd gets it right. This is something that really ought to get fixe durin 2.5

#8 lore raw

Re: CDROM driver does not support Linux partition tables

Quoted 8 lines · Alan Cox
Quoted 4 lines · Jens Axboe
Quoted 2 lines

It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.

The opposite, surely? sr uses one minor per cd-rom, ide-cd has 64.

Brain on stun. Yes ide-scsi is a problem ide-cd gets it right. This is something that really ought to get fixe durin 2.5

Hrm. Then how does one access the other minors? I tried creating the presumed-appropriate device nodes directly via mknod (cdrom0 was 22,0; I created 22,1 22,2 22,3) without success. I didn't have ide-scsi loaded at the time.

Signature · 5 lines
 *********  Fight Back!  It may not be just YOUR life at risk.  *********
 :phil stracchino : unix ronin : renaissance man : mystic zen biker geek:
 : [email protected]   :::   [email protected]   :::    [email protected] :
 :  2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold)  :
 :    Linux Now! ...because friends don't let friends use Microsoft.    :
#9 lore raw

Re: CDROM driver does not support Linux partition tables

In reply to Phil Stracchino
Quoted 13 lines · Phil Stracchino

A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.

Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?

Quoted 4 lines

(The particular case in which this came up is someone who has a Sun box without a CDROM drive in it, and wants to use a Linux box as a jumpstart server, but can't because the Linux box can't read beyond the first slice on the CD.)

Can the disk be copied to a file or hard disk and mounted there?

Signature · 2 lines
Måns Rullgård
[email protected]
#10 lore raw

Re: CDROM driver does not support Linux partition tables

Quoted 8 lines · M?ns Rullg?rd
Quoted 5 lines · Phil Stracchino

Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.

Can the disk be copied to a file or hard disk and mounted there?

Copied with dd? I don't know, but it's a thought. I suspect the ide-scsi route Alan suggested is more promising.

Signature · 5 lines
 *********  Fight Back!  It may not be just YOUR life at risk.  *********
 :phil stracchino : unix ronin : renaissance man : mystic zen biker geek:
 : [email protected]   :::   [email protected]   :::    [email protected] :
 :  2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold)  :
 :    Linux Now! ...because friends don't let friends use Microsoft.    :
#11 lore raw

Re: CDROM driver does not support Linux partition tables

In reply to Phil Stracchino

Hi,

Quoted 6 lines · Phil Stracchino

A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.

I remember someone tangling around with the partitioning code. Care to comment?

Thunder

Signature · 4 lines
--./../...-/. -.--/---/..-/.-./..././.-../..-. .---/..-/.../- .-
--/../-./..-/-/./--..-- ../.----./.-../.-.. --./../...-/. -.--/---/..-
.- -/---/--/---/.-./.-./---/.--/.-.-.-
--./.-/-.../.-./.././.-../.-.-.-