PROBLEM: Kernel 2.4.19 does not export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations
PROBLEM SUMMARY:
Kernel 2.4.19 apparently fails to export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations
While trying to isolate an apparent progressive hardware failure, I had cause to swap the disks and SCSI controller from a K6-III/450 machine running kernel 2.4.19 into an Athlon/1200 machine. Having done so, I rebuilt the kernel with Athlon optimizations instead of K6-III.
Despite making no other change in the kernel configuration, this yielded an unusable kernel. The machine would boot, but almost all modules failed to load and the system as a whole was not usable running on that kernel. All failures appeared to come down to a single error, reporting _mmx_memcpy as an unresolved symbol. It appears that for some reason _mmx_memcpy is not exported from the kernel if Athlon optimization is used.
The system was sufficiently non-functional that I was unable to capture a log of the error messages.
Being of a suspicious nature, I generated .config files for K6 and Athlon optimizations, and discovered the following:
.config Wed Sep 4 13:59:39 2002 renamed from .config.k6 Wed Sep 4 01:22:11 2002 +6 -4
@@ -29,8 +29,8 @@ # CONFIG_M686 is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUM4 is not set -CONFIG_MK6=y -# CONFIG_MK7 is not set +# CONFIG_MK6 is not set +CONFIG_MK7=y # CONFIG_MELAN is not set # CONFIG_MCRUSOE is not set # CONFIG_MWINCHIPC6 is not set
@@ -45,9 +45,11 @@ CONFIG_X86_POPAD_OK=y # CONFIG_RWSEM_GENERIC_SPINLOCK is not set CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_X86_L1_CACHE_SHIFT=5 -CONFIG_X86_ALIGNMENT_16=y +CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_X86_TSC=y +CONFIG_X86_GOOD_APIC=y +CONFIG_X86_USE_3DNOW=y +CONFIG_X86_PGE=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_MCE=y # CONFIG_TOSHIBA is not set
The significant thing here seems to be that CONFIG_X86_USE_3DNOW is not enabled when compiling for K6, because K6, K6-II and K6-III are treated as the same processor, even though the K6-III does in fact support 3DNow. I was baffled as to why 3DNow code would work with K6 optimizations but not with Athlon, but now I see that the explanation of that particular puzzle is that it wasn't being usedd on K6. I'm minded to try building a K6-optimized kernel with CONFIG_X86_USE_3DNOW turned on, but I don't have the results of that experiment yet and will report on it when I do.
ver_linux output:
/*
* scripts/ver_linux doesn't report the binutils
* version, an omission that should be remedied.
* the following simple change would accomplish
* this, as well as improving readability of the
* output:
ver_linux Wed Sep 4 13:51:32 2002 renamed from ver_linux.orig Sun Sep 2 10:27:18 2001 +2 -1
@@ -12,7 +12,8 @@ uname -a echo ' ' -echo "Gnu C " `gcc --version` +echo "Gnu C " `gcc --version | head -1` +echo "Binutils (from ld) " `ld --version | head -1` make --version 2>&1 | awk -F, '{print $1}' | awk \ '/GNU Make/{print "Gnu make ",$NF}'
* The following output is as patched:
*/Linux babylon5 2.4.19 #7 Wed Sep 4 00:32:43 EDT 2002 i686 unknown
Gnu C gcc (GCC) 3.2 Binutils (from ld) GNU ld version 2.12 Gnu make 3.79.1 util-linux 2.11f mount 2.11f modutils 2.4.6 e2fsprogs 1.25 reiserfsprogs 3.x.0b PPP 2.4.0b4 Linux C Library 2.1.3 Dynamic linker (ldd) 2.1.3 Linux C++ Library 5.0.0 Procps 2.0.2 Net-tools 1.60 Kbd 0.99 Sh-utils 1.16 Modules Loaded ppp_deflate bsd_comp ppp_async ppp_generic slhc
audiopci pnp soundbase sndshield serial nfs lockd sunrpc iptable_filter ipt_MASQUERADE ip_nat_irc ip_conntrack_irc iptable_nat ip_tables mousedev hid input usb-uhci usbcore st sg lp parport_pc parport isofs inflate_fs sr_mod cdrom
binutils 2.12
/*
* scripts/ver_linux doesn't report the binutils
* version, an omission that should be remedied.
* the following one-line patch would accomplish
* this, as well as improving readability:
*** scripts/ver_linux.orig Sun Sep 2 10:27:18 2001
--- scripts/ver_linux Wed Sep 4 13:51:32 2002
***************
*** 12,18 ****
uname -a
echo ' '
! echo "Gnu C " gcc --version
make --version 2>&1 | awk -F, '{print $1}' | awk \
'/GNU Make/{print "Gnu make ",$NF}'
--- 12,19 ----
uname -a
echo ' '
! echo "Gnu C " gcc --version | head -1
! echo "Binutils (from ld) " ld --version | head -1
make --version 2>&1 | awk -F, '{print $1}' | awk \
'/GNU Make/{print "Gnu make ",$NF}'*/
/proc/cpuinfo:
processor : 0vendor_id : AuthenticAMD
cpu family : 6
model : 4
model name : AMD Athlon(tm) Processor
stepping : 4
cpu MHz : 1200.097
cache size : 256 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
bogomips : 2392.06
/proc/ioports:
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
02f8-02ff : serial(auto)
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-40ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] 5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] 6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] c000-cfff : PCI Bus #01
c000-c0ff : 3Dfx Interactive, Inc. Voodoo 3
d000-d00f : VIA Technologies, Inc. Bus Master IDE d400-d41f : VIA Technologies, Inc. UHCI USB
d400-d41f : usb-uhci
d800-d81f : VIA Technologies, Inc. UHCI USB (#2)
d800-d81f : usb-uhci
dc00-dc3f : Ensoniq ES1370 [AudioPCI]
dc00-dc3f : AudioPCI
e000-e07f : 3Com Corporation 3c905B 100BaseTX [Cyclone]
e000-e07f : 00:09.0
e400-e403 : BusLogic BT-946C (BA80C30) [MultiMaster 10]
e400-e403 : BusLogic BT-958
/proc/iomem:
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000cffff : Extension ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
00100000-002098c6 : Kernel code
002098c7-0027953f : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage 0fff3000-0fffffff : ACPI Tables
d0000000-d3ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133] d4000000-d7ffffff : PCI Bus #01
d4000000-d5ffffff : 3Dfx Interactive, Inc. Voodoo 3
d8000000-d9ffffff : PCI Bus #01
d8000000-d9ffffff : 3Dfx Interactive, Inc. Voodoo 3
db000000-db00007f : 3Com Corporation 3c905B 100BaseTX [Cyclone] db001000-db001fff : BusLogic BT-946C (BA80C30) [MultiMaster 10] ffff0000-ffffffff : reserved
/proc/modules:
ppp_deflate 39584 0 (autoclean) bsd_comp 4288 0 (autoclean) ppp_async 7504 1 (autoclean) ppp_generic 15520 3 (autoclean) [ppp_deflate bsd_comp ppp_async] slhc 4960 1 (autoclean) [ppp_generic] audiopci 16768 0 pnp 49904 0 [audiopci] soundbase 846480 0 [audiopci pnp] sndshield 11488 0 [audiopci pnp soundbase] serial 45920 2 (autoclean) nfs 66608 7 (autoclean) lockd 46640 1 (autoclean) [nfs] sunrpc 59552 1 (autoclean) [nfs lockd] iptable_filter 1680 0 (autoclean) (unused) ipt_MASQUERADE 1824 2 (autoclean) ip_nat_irc 2976 0 (unused) ip_conntrack_irc 2704 0 [ip_nat_irc] iptable_nat 20096 9 [ipt_MASQUERADE ip_nat_irc] ip_tables 14048 5 [iptable_filter ipt_MASQUERADE iptable_nat] mousedev 4128 1 hid 18640 0 (unused) input 3456 0 [mousedev hid] usb-uhci 21808 0 (unused) usbcore 63872 1 [hid usb-uhci] st 26544 0 (unused) sg 31344 0 (unused) lp 6432 0 (unused) parport_pc 21952 1 parport 25024 1 [lp parport_pc] isofs 25280 1 (autoclean) inflate_fs 17760 0 (autoclean) [isofs] sr_mod 13280 0 (autoclean) (unused) cdrom 26592 0 (autoclean) [sr_mod]
lspci:
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0305 (rev
02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: <available only to root>
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8305
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d4000000-d7ffffff
Prefetchable memory behind bridge: d8000000-d9ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: VIA Technologies, Inc.: Unknown device 0686 (rev 22)
Subsystem: Unknown device 1106:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
10) (prog-if 8a)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at d000
Capabilities: <available only to root>
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d400
Capabilities: <available only to root>
00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d800
Capabilities: <available only to root>
00:07.4 Host bridge: VIA Technologies, Inc.: Unknown device 3057 (rev
30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: <available only to root>
00:08.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI] (rev 01)
Subsystem: Unknown device 4942:4c4c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 12 min, 128 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00
00:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: Unknown device 10b7:9055
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 10 min, 10 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e000
Region 1: Memory at db000000 (32-bit, non-prefetchable)
Capabilities: <available only to root>
00:0c.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10] (rev 08)
Subsystem: Unknown device 104b:1040
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 8 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e400
Region 1: Memory at db001000 (32-bit, non-prefetchable)
01:00.0 VGA compatible controller: 3Dfx Interactive, Inc.: Unknown device 0005 (rev 01)
Subsystem: Unknown device 121a:0030
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 14
Region 0: Memory at d4000000 (32-bit, non-prefetchable) Region 1: Memory at d8000000 (32-bit, prefetchable) Region 2: I/O ports at c000
Capabilities: <available only to root>
/proc/scsi/scsi:
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DDYS-T18350N Rev: S96H
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: DNES-318350W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Signature · 5 lines
********* Fight Back! It may not be just YOUR life at risk. ********* phil stracchino :: [email protected] :: [email protected] unix ronin :::: renaissance man :::: mystic zen biker geek 2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold) Linux Now! ...because friends don't let friends use Microsoft.
FOLLOWUP: Kernel 2.4.19 does not export _mmx_memcpy when compiled with gcc-3.2 and Athlon optimizations
FOLLOWUP:
I built a K6-optimized kernel and manually turned on CONFIG_X86_USE_3DNOW before beginning compilation, installed the kernel, and ran depmod -a. The result:
babylon5:root:/usr/src/linux-2.4.19:65 # depmod -a
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/block/rd.o
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/cdrom/cdrom.o
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/char/serial.o
depmod: *** Unresolved symbols in /lib/modules/2.4.19/kernel/drivers/ide/ide-cd.o
...
...
... well, you get the idea. A total of 40 modules fail, all with the same error. The following is the list of failed modules:
drivers/block/rd.odrivers/cdrom/cdrom.odrivers/char/serial.odrivers/ide/ide-cd.odrivers/md/lvm-mod.odrivers/md/raid5.odrivers/net/ppp_async.odrivers/net/ppp_deflate.odrivers/net/ppp_generic.odrivers/net/slhc.odrivers/net/slip.odrivers/parport/parport.odrivers/parport/parport_pc.odrivers/pcmcia/pcmcia_core.odrivers/scsi/aic7xxx/aic7xxx.odrivers/scsi/ide-scsi.odrivers/scsi/sg.odrivers/scsi/sr_mod.odrivers/scsi/st.odrivers/usb/hid.odrivers/usb/storage/usb-storage.odrivers/usb/usb-uhci.odrivers/usb/usbcore.ofs/fat/fat.ofs/inflate_fs/inflate_fs.ofs/intermezzo/intermezzo.ofs/isofs/isofs.ofs/lockd/lockd.ofs/minix/minix.ofs/nfs/nfs.ofs/nfsd/nfsd.ofs/reiserfs/reiserfs.ofs/smbfs/smbfs.ofs/udf/udf.ofs/ufs/ufs.ofs/vfat/vfat.onet/ipv4/netfilter/ip_tables.onet/ipv4/netfilter/ipt_REJECT.onet/ipv4/netfilter/iptable_nat.onet/sunrpc/sunrpc.o
So it definitely looks like something is unhappy with CONFIG_X86_USE_3DNOW, possibly only when compiled with gcc-3.2, possibly not. Why it's not being exported, I have no idea; as far as I can tell, it should be.
I haven't tried building an Athlon-optimized kernel *without* using CONFIG_X86_USE_3DNOW.
Signature · 5 lines
********* Fight Back! It may not be just YOUR life at risk. ********* phil stracchino :: [email protected] :: [email protected] unix ronin :::: renaissance man :::: mystic zen biker geek 2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold) Linux Now! ...because friends don't let friends use Microsoft.
Quoted 3 lines · Phil Stracchino
PROBLEM SUMMARY:
Kernel 2.4.19 apparently fails to export_mmx_memcpywhen compiled with gcc-3.2 and Athlon optimizations
You need to save your .config make distclean, restore it make oldconfig dep and build the kernel. Its a known limitation in the CML1 config tools
Quoted 8 lines · Alan Cox
Quoted 3 lines · Phil Stracchino
PROBLEM SUMMARY:
Kernel 2.4.19 apparently fails to export_mmx_memcpywhen compiled with gcc-3.2 and Athlon optimizationsYou need to save your .config make distclean, restore it make oldconfig dep and build the kernel. Its a known limitation in the CML1 config tools
Aha, so it's a known config problem, not bizarre psychic terrorism on the part of the source code. Thank you for saving my sanity. :) I'll give that procedure a shot.
Signature · 5 lines
********* Fight Back! It may not be just YOUR life at risk. ********* phil stracchino :: [email protected] :: [email protected] unix ronin :::: renaissance man :::: mystic zen biker geek 2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold) Linux Now! ...because friends don't let friends use Microsoft.
CDROM driver does not support Linux partition tables
In reply to Alan CoxA deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.
Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?
(The particular case in which this came up is someone who has a Sun box without a CDROM drive in it, and wants to use a Linux box as a jumpstart server, but can't because the Linux box can't read beyond the first slice on the CD.)
Signature · 5 lines
********* Fight Back! It may not be just YOUR life at risk. ********* :phil stracchino : unix ronin : renaissance man : mystic zen biker geek: : [email protected] ::: [email protected] ::: [email protected] : : 2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold) : : Linux Now! ...because friends don't let friends use Microsoft. :
Re: CDROM driver does not support Linux partition tables
Quoted 8 lines · Phil Stracchino
A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.
Quoted 4 lines
Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?
It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.
Re: CDROM driver does not support Linux partition tables
Quoted 9 lines · Alan Cox
Quoted 8 lines · Phil Stracchino
A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.
Quoted 7 lines
Quoted 4 lines
Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?
It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.
The opposite, surely? sr uses one minor per cd-rom, ide-cd has 64.
Signature · 1 line
Jens Axboe
Re: CDROM driver does not support Linux partition tables
Quoted 4 lines · Jens Axboe
Quoted 2 lines
It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.
The opposite, surely? sr uses one minor per cd-rom, ide-cd has 64.
Brain on stun. Yes ide-scsi is a problem ide-cd gets it right. This is something that really ought to get fixe durin 2.5
Re: CDROM driver does not support Linux partition tables
Quoted 8 lines · Alan Cox
Quoted 4 lines · Jens Axboe
Quoted 2 lines
It ought to be supportable on scsi cd or with ide-scsi. ide-cd has no minor space for partitioning, ide-scsi/sr do support partitions.
The opposite, surely? sr uses one minor per cd-rom, ide-cd has 64.
Brain on stun. Yes ide-scsi is a problem ide-cd gets it right. This is something that really ought to get fixe durin 2.5
Hrm. Then how does one access the other minors? I tried creating the presumed-appropriate device nodes directly via mknod (cdrom0 was 22,0; I created 22,1 22,2 22,3) without success. I didn't have ide-scsi loaded at the time.
Signature · 5 lines
********* Fight Back! It may not be just YOUR life at risk. ********* :phil stracchino : unix ronin : renaissance man : mystic zen biker geek: : [email protected] ::: [email protected] ::: [email protected] : : 2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold) : : Linux Now! ...because friends don't let friends use Microsoft. :
Re: CDROM driver does not support Linux partition tables
In reply to Phil StracchinoQuoted 13 lines · Phil Stracchino
A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.
Is this something that's supposed to happen, and is there a reason why it's not supported, or is it simply that no-one has asked for it to be supported and/or no-one has gotten around to implementing it because of lack of demand?
Quoted 4 lines
(The particular case in which this came up is someone who has a Sun box without a CDROM drive in it, and wants to use a Linux box as a jumpstart server, but can't because the Linux box can't read beyond the first slice on the CD.)
Can the disk be copied to a file or hard disk and mounted there?
Signature · 2 lines
Måns Rullgård [email protected]
Re: CDROM driver does not support Linux partition tables
Quoted 8 lines · M?ns Rullg?rd
Quoted 5 lines · Phil Stracchino
Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.
Can the disk be copied to a file or hard disk and mounted there?
Copied with dd? I don't know, but it's a thought. I suspect the ide-scsi route Alan suggested is more promising.
Signature · 5 lines
********* Fight Back! It may not be just YOUR life at risk. ********* :phil stracchino : unix ronin : renaissance man : mystic zen biker geek: : [email protected] ::: [email protected] ::: [email protected] : : 2000 CBR929RR, 1991 VFR750F3 (foully murdered), 1986 VF500F (sold) : : Linux Now! ...because friends don't let friends use Microsoft. :
Re: CDROM driver does not support Linux partition tables
In reply to Phil StracchinoHi,
Quoted 6 lines · Phil Stracchino
A deficiency in the Linux CDROM driver was just brought to my attention. Even on a kernel configured with support for UFS and Sun partition tables, it doesn't appear to be possible to mount any but the first slice of a Sun CDROM containing multiple slices. Essentially, it seems that Solaris partition table support doesn't trickle down to the CDROM driver.
I remember someone tangling around with the partitioning code. Care to comment?
Thunder
Signature · 4 lines
--./../...-/. -.--/---/..-/.-./..././.-../..-. .---/..-/.../- .- --/../-./..-/-/./--..-- ../.----./.-../.-.. --./../...-/. -.--/---/..- .- -/---/--/---/.-./.-./---/.--/.-.-.- --./.-/-.../.-./.././.-../.-.-.-