Skip to contentSkip to conversation

Linux 2.4.20pre5-ac5

DISCUSSION Tony Spinillo 2 participants 3 messages Sep 11, 2002 – Sep 12, 2002

lore
Share & tools
lore
#0 lore raw

I just fired it up an an Asus P4B533-V (845G-Award Medallion Bios v6.0)
board. Seemed to work well :) . Full DMA on the DVD drive.

I took a gamble to see if my old "non-appearing" drives problem was fixed, and tried it on the Gigabyte 845IGX (845G-Award Modular Bios V6.0PG), I was not as lucky. I think my next board will be an Asus. ;)

Full dmesg, lscpi links below, for anyone who is interested. Let me know if you need anymore info.

Thanks!

Tony

ASUS dmesg/lspci links:
http://ac.marywood.edu/tspin/www/dmesg2420pre5ac5asus.txt
http://ac.marywood.edu/tspin/www/lspci2420pre5ac5asus.txt
Gigabyte dmesg/lspci links:
http://ac.marywood.edu/tspin/www/lspci2420pre5ac5gb.txt
http://ac.marywood.edu/tspin/www/dmesg2420pre5ac5gb.txt

__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute

#1 lore raw
Quoted 8 lines · Tony Spinillo

I just fired it up an an Asus P4B533-V (845G-Award Medallion Bios v6.0)
board. Seemed to work well :) . Full DMA on the DVD drive.

I took a gamble to see if my old "non-appearing" drives problem was fixed, and tried it on the Gigabyte 845IGX (845G-Award Modular Bios V6.0PG), I was not as lucky. I think my next board will be an Asus. ;)

Can you try one thing for me on the problem board. Build the PIIX driver modular, and build with ide task file disabled

Next boot the system (single user read only if you want)- you should get the drives in basic PIO mode. Then modprobe piix and see if it finds the drives that way around

#2 lore raw

Alan,

I tagged piix as modular and removed the task file stuff. The DVD and burner showedup. Running atapci, showed the drives as DMA enabled (I had to pick Generic PCI bus-master DMA support to get the piix option).
Hdparm would not work with piix loaded, I got similiar errors when trying to mount (see below).

I could mount a cd and copy files no problem(without piix loaded). I then loaded the piix module. It loaded sucessfully. I tried to mount the cd and got errors.
Also /proc/ide/piix did not show up.

Log snips below, I also put links to full files at end of message.

If I missed something or you need anything else
let me know. Thanks!

Tony

atapci before piix load (it's the same afterward):
pcibus = 33333
00:1f.1 vendor=8086 device=24cb class=0101 irq=16 base4=cc01 ----------PIIX BusMastering IDE Configuration---------------

Driver Version:                     1.3
South Bridge:                       9419
Revision:                           IDE 0x1
Highest DMA rate:                   UDMA133
BM-DMA base:                        0xcc00
PCI clock:                          33.3MHz
-----------------------Primary IDE-------Secondary IDE------
Enabled:                      yes                 yes
Simplex only:                  no                  no
Cable Type:                   80w                 80w
-------------------drive0----drive1----drive2----drive3-----
Prefetch+Post:        yes        no       yes        no
Transfer Mode:       UDMA       PIO      UDMA       PIO
Address Setup:       90ns      90ns      90ns      90ns
Cmd Active:         360ns     360ns     360ns     360ns
Cmd Recovery:       540ns     540ns     540ns     540ns
Data Active:         90ns     360ns      90ns     360ns
Data Recovery:       30ns     540ns      30ns     540ns
Cycle Time:          60ns     900ns      60ns     900ns
Transfer Rate:   33.3MB/s   2.2MB/s  33.3MB/s   2.2MB/s

********
piix loading:
localhost kernel: ICH4: IDE controller at PCI slot 00:1f.1 localhost kernel: ICH4: chipset revision 1
localhost kernel: ICH4: not 100%% native mode: will probe irqs later
localhost kernel: ide0: BM-DMA at 0xcc00-0xcc07, BIOS settings:
hda:DMA, hdb:pio
localhost kernel: ide1: BM-DMA at 0xcc08-0xcc0f, BIOS settings:
hdc:DMA, hdd:pio
********
errors when mounting cdrom after loading piix:
localhost kernel: ide0: reset timed-out, status=0xff localhost kernel: end_request: I/O error, dev 03:00 (hda), sector 0 localhost last message repeated 4 times
localhost kernel: end_request: I/O error, dev 03:00 (hda), sector 64 localhost kernel: isofs_read_super: bread failed, dev=03:00, iso_blknum=16, block=32
localhost kernel: end_request: I/O error, dev 03:00 (hda), sector 0 ******* dmesg when booting without piix:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: LITEON DVD-ROM LTD163, ATAPI CD/DVD-ROM drive
hdc: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ATAPI 48X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache
**********

Links to full files:
http://ac.marywood.edu/tspin/www/atapci.txt
http://ac.marywood.edu/tspin/www/dmesgnopiix.txt
Mounting errors after piix load
http://ac.marywood.edu/tspin/www/mount.txt
modprobing piix
http://ac.marywood.edu/tspin/www/piixload.txt
Kernel config
http://ac.marywood.edu/tspin/www/config.txt
gigabyte lspci
http://ac.marywood.edu/tspin/www/lspcigb.txt

Quoted 14 lines · --- Alan Cox
Quoted 8 lines · Tony Spinillo

I just fired it up an an Asus P4B533-V (845G-Award Medallion Bios v6.0)
board. Seemed to work well :) . Full DMA on the DVD drive.

I took a gamble to see if my old "non-appearing" drives problem was fixed, and tried it on the Gigabyte 845IGX (845G-Award Modular Bios V6.0PG), I was not as lucky. I think my next board will be an Asus. ;)

Can you try one thing for me on the problem board. Build the PIIX driver
modular, and build with ide task file disabled

Quoted 6 lines

Next boot the system (single user read only if you want)- you should get
the drives in basic PIO mode. Then modprobe piix and see if it finds the
drives that way around

__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com