Linux 2.4.20pre5-ac5
I just fired it up an an Asus P4B533-V (845G-Award Medallion Bios v6.0)
board. Seemed to work well :) . Full DMA on the DVD drive.
I took a gamble to see if my old "non-appearing" drives problem was fixed, and tried it on the Gigabyte 845IGX (845G-Award Modular Bios V6.0PG), I was not as lucky. I think my next board will be an Asus. ;)
Full dmesg, lscpi links below, for anyone who is interested. Let me know if you need anymore info.
Thanks!
Tony
ASUS dmesg/lspci links:
http://ac.marywood.edu/tspin/www/dmesg2420pre5ac5asus.txt
http://ac.marywood.edu/tspin/www/lspci2420pre5ac5asus.txt
Gigabyte dmesg/lspci links:
http://ac.marywood.edu/tspin/www/lspci2420pre5ac5gb.txt
http://ac.marywood.edu/tspin/www/dmesg2420pre5ac5gb.txt
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
Quoted 8 lines · Tony Spinillo
I just fired it up an an Asus P4B533-V (845G-Award Medallion Bios v6.0)
board. Seemed to work well :) . Full DMA on the DVD drive.I took a gamble to see if my old "non-appearing" drives problem was fixed, and tried it on the Gigabyte 845IGX (845G-Award Modular Bios V6.0PG), I was not as lucky. I think my next board will be an Asus. ;)
Can you try one thing for me on the problem board. Build the PIIX driver modular, and build with ide task file disabled
Next boot the system (single user read only if you want)- you should get the drives in basic PIO mode. Then modprobe piix and see if it finds the drives that way around
Alan,
I tagged piix as modular and removed the task file stuff. The DVD and burner showedup. Running atapci, showed the drives as DMA enabled (I had to pick Generic PCI bus-master DMA support to get the piix option).
Hdparm would not work with piix loaded, I got similiar errors when trying to mount (see below).
I could mount a cd and copy files no problem(without piix loaded). I then loaded the piix module. It loaded sucessfully. I tried to mount the cd and got errors.
Also /proc/ide/piix did not show up.
Log snips below, I also put links to full files at end of message.
If I missed something or you need anything else
let me know. Thanks!
Tony
atapci before piix load (it's the same afterward):
pcibus = 33333
00:1f.1 vendor=8086 device=24cb class=0101 irq=16 base4=cc01 ----------PIIX BusMastering IDE Configuration---------------
Driver Version: 1.3 South Bridge: 9419 Revision: IDE 0x1 Highest DMA rate: UDMA133 BM-DMA base: 0xcc00 PCI clock: 33.3MHz -----------------------Primary IDE-------Secondary IDE------ Enabled: yes yes Simplex only: no no Cable Type: 80w 80w -------------------drive0----drive1----drive2----drive3----- Prefetch+Post: yes no yes no Transfer Mode: UDMA PIO UDMA PIO Address Setup: 90ns 90ns 90ns 90ns Cmd Active: 360ns 360ns 360ns 360ns Cmd Recovery: 540ns 540ns 540ns 540ns Data Active: 90ns 360ns 90ns 360ns Data Recovery: 30ns 540ns 30ns 540ns Cycle Time: 60ns 900ns 60ns 900ns Transfer Rate: 33.3MB/s 2.2MB/s 33.3MB/s 2.2MB/s
********
piix loading:
localhost kernel: ICH4: IDE controller at PCI slot 00:1f.1 localhost kernel: ICH4: chipset revision 1
localhost kernel: ICH4: not 100%% native mode: will probe irqs later
localhost kernel: ide0: BM-DMA at 0xcc00-0xcc07, BIOS settings:
hda:DMA, hdb:pio
localhost kernel: ide1: BM-DMA at 0xcc08-0xcc0f, BIOS settings:
hdc:DMA, hdd:pio
********
errors when mounting cdrom after loading piix:
localhost kernel: ide0: reset timed-out, status=0xff localhost kernel: end_request: I/O error, dev 03:00 (hda), sector 0 localhost last message repeated 4 times
localhost kernel: end_request: I/O error, dev 03:00 (hda), sector 64 localhost kernel: isofs_read_super: bread failed, dev=03:00, iso_blknum=16, block=32
localhost kernel: end_request: I/O error, dev 03:00 (hda), sector 0 ******* dmesg when booting without piix:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: LITEON DVD-ROM LTD163, ATAPI CD/DVD-ROM drive
hdc: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ATAPI 48X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache
**********
Links to full files:
http://ac.marywood.edu/tspin/www/atapci.txt
http://ac.marywood.edu/tspin/www/dmesgnopiix.txt
Mounting errors after piix load
http://ac.marywood.edu/tspin/www/mount.txt
modprobing piix
http://ac.marywood.edu/tspin/www/piixload.txt
Kernel config
http://ac.marywood.edu/tspin/www/config.txt
gigabyte lspci
http://ac.marywood.edu/tspin/www/lspcigb.txt
Quoted 14 lines · --- Alan Cox
Quoted 8 lines · Tony Spinillo
I just fired it up an an Asus P4B533-V (845G-Award Medallion Bios v6.0)
board. Seemed to work well :) . Full DMA on the DVD drive.I took a gamble to see if my old "non-appearing" drives problem was fixed, and tried it on the Gigabyte 845IGX (845G-Award Modular Bios V6.0PG), I was not as lucky. I think my next board will be an Asus. ;)
Can you try one thing for me on the problem board. Build the PIIX driver
modular, and build with ide task file disabled
Quoted 6 lines
Next boot the system (single user read only if you want)- you should get
the drives in basic PIO mode. Then modprobe piix and see if it finds the
drives that way around
__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com