Skip to contentSkip to conversation

ppc-bug

DISCUSSION 于婧 1 participant 1 message Nov 19, 2002

lore
Share & tools
lore

于婧

author
#0 lore raw

hi!
montavista said :

The following lists information about the LSP support level, the board versions tested, the firmware tested, and board features supported. Board versions and firmware not tested are not supported at this time. #The Motorola LoPEC LSP is supported for development and deployment with Pro 2.1.
#The board version tested was Motorola LoPEC version 1.0.
#The firmware tested was PPC1-Bug.

While,motorola said there is no different version of motorola lopec 7410.And the version of ppcbug is always ppc5-bug.

Quoted 90 lines

I'm porting mvista linux 2.1 for the motorola lopec mpc7410 board.And
I noticed that there are some differences between the board version described by mvista and motorola.Also,the version of PPCBug is different.I'm wondering why?
Here is my board starting information:
///////////
Copyright Motorola Inc. 1988 - 2001, All Rights Reserved

PPC5 Debugger/Diagnostics Release Version 1.3 - 04/27/2001 RM01 COLD Start

Quoted 1 line

Local Memory Found =20000000 (&536870912)

MPU Clock Speed =400Mhz

BUS Clock Speed =100Mhz

Quoted 1 line

Reset Vector Location : ROM Bank B
Mezzanine Configuration: Single-MPU
Current 60X-Bus Master : MPU0
Idle MPU(s) : NONE

L2Cache:       2048KB, 200Mhz
System Memory: 512MB, ECC Enabled (ECC-Memory Detected)
Quoted 1 line

PPC5-Bug>CNFG
Board (PWA) Serial Number = "6016204 "

Board Identifier          = "LoPEC-P011      "
Artwork (PWA) Identifier  = "01-W3646F11B    "
MPU Clock Speed           = "400"
BUS Clock Speed           = "100"
Ethernet Address          = 0001AF0996C8
Primary SCSI Identifier   = "07"
System Serial Number      = "0               "
System Identifier         = "0                              "
License Identifier        = "6016204  "

//////////////////

When I port the mvista linux v2.1(motorola lopec 74xx lsp),the

Quoted 1 line

starting information is showed below:

//////////////

Quoted 1 line

Copyright Motorola Inc. 1988 - 2001, All Rights Reserved

PPC5 Debugger/Diagnostics Release Version 1.3 - 04/27/2001 RM01 COLD Start

Quoted 1 line

Local Memory Found =20000000 (&536870912)

MPU Clock Speed =400Mhz

BUS Clock Speed =100Mhz

Quoted 1 line

Reset Vector Location : ROM Bank B
Mezzanine Configuration: Single-MPU
Current 60X-Bus Master : MPU0
Idle MPU(s) : NONE

Quoted 1 line

L2Cache: 2048KB, 200Mhz

Initializing System Memory (DRAM)...

L2Cache:       2048KB, 200Mhz
System Memory: 512MB, ECC Enabled (ECC-Memory Detected)

SelfTest/Boots about to Begin... Press <BREAK> at anytime to Abort ALL

Quoted 1 line

NetBoot about to Begin... Press <ESC> to Bypass, <SPC> to Continue

Network Booting from: I82559, Controller 0, Device 0 Device Name: /pci@fec00000/pci8086,1209@e,0:0,0
Loading: vmlinuz-motorola-lopec

Quoted 1 line

Client IP Address = 192.168.201.3

Server IP Address = 192.168.201.1
Gateway IP Address = 0.0.0.0
Subnet IP Address Mask = 255.255.255.0
Boot File Name = vmlinuz-motorola-lopec
Argument File Name =

Network Boot File load in progress... To abort hit <BREAK>

Bytes Received =&784800, Bytes Loaded =&784800
Bytes/Second =&392400, Elapsed Time =2 Second(s)

Residual-Data Located at: $1FED16DC

Quoted 1 line

loaded at: 00005400 000C65BC

relocated to: 00800000 008C11BC

Quoted 1 line

zimage at: 00805A00 008BD53E

avail ram: 00400000 00800000

Quoted 8 lines

Linux/PPC load: ip=on

Quoted 1 line

Uncompressing Linux...done.

Now booting the kernel

///////////////////////////////////////////////////////////////////////////

Quoted 1 line

After "Now booting the kernel",there is nothing put on the screen.I don't know why?Can you help me?

= = = = = = = = = = = = = = = = = = = =

������������
����������������[email protected]
��������������������2002-11-15

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/