ppc-bug
hi!
montavista said :
The following lists information about the LSP support level, the board versions tested, the firmware tested, and board features supported. Board versions and firmware not tested are not supported at this time. #The Motorola LoPEC LSP is supported for development and deployment with Pro 2.1.
#The board version tested was Motorola LoPEC version 1.0.
#The firmware tested was PPC1-Bug.
While,motorola said there is no different version of motorola lopec 7410.And the version of ppcbug is always ppc5-bug.
Quoted 90 lines
I'm porting mvista linux 2.1 for the motorola lopec mpc7410 board.And
I noticed that there are some differences between the board version described by mvista and motorola.Also,the version of PPCBug is different.I'm wondering why?
Here is my board starting information:
///////////
Copyright Motorola Inc. 1988 - 2001, All Rights ReservedPPC5 Debugger/Diagnostics Release Version 1.3 - 04/27/2001 RM01 COLD Start
Quoted 1 line
Local Memory Found =20000000 (&536870912)
MPU Clock Speed =400Mhz
BUS Clock Speed =100Mhz
Quoted 1 line
Reset Vector Location : ROM Bank B
Mezzanine Configuration: Single-MPU
Current 60X-Bus Master : MPU0
Idle MPU(s) : NONEL2Cache: 2048KB, 200Mhz System Memory: 512MB, ECC Enabled (ECC-Memory Detected)Quoted 1 line
PPC5-Bug>CNFG
Board (PWA) Serial Number = "6016204 "Board Identifier = "LoPEC-P011 " Artwork (PWA) Identifier = "01-W3646F11B " MPU Clock Speed = "400" BUS Clock Speed = "100" Ethernet Address = 0001AF0996C8 Primary SCSI Identifier = "07" System Serial Number = "0 " System Identifier = "0 " License Identifier = "6016204 "//////////////////
When I port the mvista linux v2.1(motorola lopec 74xx lsp),the
Quoted 1 line
starting information is showed below:
//////////////
Quoted 1 line
Copyright Motorola Inc. 1988 - 2001, All Rights Reserved
PPC5 Debugger/Diagnostics Release Version 1.3 - 04/27/2001 RM01 COLD Start
Quoted 1 line
Local Memory Found =20000000 (&536870912)
MPU Clock Speed =400Mhz
BUS Clock Speed =100Mhz
Quoted 1 line
Reset Vector Location : ROM Bank B
Mezzanine Configuration: Single-MPU
Current 60X-Bus Master : MPU0
Idle MPU(s) : NONEQuoted 1 line
L2Cache: 2048KB, 200Mhz
Initializing System Memory (DRAM)...
L2Cache: 2048KB, 200Mhz System Memory: 512MB, ECC Enabled (ECC-Memory Detected)SelfTest/Boots about to Begin... Press <BREAK> at anytime to Abort ALL
Quoted 1 line
NetBoot about to Begin... Press <ESC> to Bypass, <SPC> to Continue
Network Booting from: I82559, Controller 0, Device 0 Device Name: /pci@fec00000/pci8086,1209@e,0:0,0
Loading: vmlinuz-motorola-lopecQuoted 1 line
Client IP Address = 192.168.201.3
Server IP Address = 192.168.201.1
Gateway IP Address = 0.0.0.0
Subnet IP Address Mask = 255.255.255.0
Boot File Name = vmlinuz-motorola-lopec
Argument File Name =Network Boot File load in progress... To abort hit <BREAK>
Bytes Received =&784800, Bytes Loaded =&784800
Bytes/Second =&392400, Elapsed Time =2 Second(s)Residual-Data Located at: $1FED16DC
Quoted 1 line
loaded at: 00005400 000C65BC
relocated to: 00800000 008C11BC
Quoted 1 line
zimage at: 00805A00 008BD53E
avail ram: 00400000 00800000
Quoted 8 lines
Linux/PPC load: ip=on
Quoted 1 line
Uncompressing Linux...done.
Now booting the kernel
///////////////////////////////////////////////////////////////////////////
Quoted 1 line
After "Now booting the kernel",there is nothing put on the screen.I don't know why?Can you help me?
= = = = = = = = = = = = = = = = = = = =
������������
����������������[email protected]
��������������������2002-11-15
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/