Skip to contentSkip to conversation

snd-powermac volume setting broken?

DISCUSSION Witold Krecicki 3 participants 5 messages Mar 12, 2004 – Mar 15, 2004

lore
Share & tools
lore
#0 lore raw

When I use alsa snd-powermac driver, the lowest volume setting (but without muting) is at about half of full volume, it's impossible to get any volume level between mute and vol=0. Is that a bug or a feature?

Signature · 3 lines
Witold Kręcicki (adasi) adasi [at] culm.net
GPG key: 7AE20871
http://www.culm.net
#1 lore raw
Quoted 3 lines · Witold Krecicki

When I use alsa snd-powermac driver, the lowest volume setting (but without muting) is at about half of full volume, it's impossible to get any volume level between mute and vol=0. Is that a bug or a feature?

Just a me too
This happens in the change from 2.6.4-rc1 to 2.6.4-rc2
I have checked the changelog and there is no change in the sound section (perhaps a change in timer.c?)

Best regards

--
Celso Gonzalez

#2 lore raw
In reply to Witold Krecicki

At Sat, 13 Mar 2004 00:15:17 +0100,

Quoted 4 lines · Witold Krecicki

When I use alsa snd-powermac driver, the lowest volume setting (but without muting) is at about half of full volume, it's impossible to get any volume level between mute and vol=0. Is that a bug or a feature?

not a bug - the chip doesn't support the level below vol=0 and it's not totally silent.

Takashi

#3 lore raw

Dnia poniedziałek 15 marzec 2004 11:07, napisałeś:

Quoted 9 lines

At Sat, 13 Mar 2004 00:15:17 +0100,

Quoted 3 lines · Witold Krecicki

When I use alsa snd-powermac driver, the lowest volume setting (but without muting) is at about half of full volume, it's impossible to get any volume level between mute and vol=0. Is that a bug or a feature?

not a bug - the chip doesn't support the level below vol=0 and it's not totally silent.

but it's not like 'not totally silent' but 'pretty loud'. On OSX volume scale is just fine.

Signature · 3 lines
Witold Kręcicki (adasi) adasi [at] culm.net
GPG key: 7AE20871
http://www.culm.net
#4 lore raw

At Mon, 15 Mar 2004 11:12:21 +0100,

Quoted 5 lines · Witold Krecicki

Dnia poniedziałek 15 marzec 2004 11:07, napisałeś:

Quoted 3 lines

At Sat, 13 Mar 2004 00:15:17 +0100,

Witold Krecicki wrote:

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

When I use alsa snd-powermac driver, the lowest volume setting (but without muting) is at about half of full volume, it's impossible to get any volume level between mute and vol=0. Is that a bug or a feature?

not a bug - the chip doesn't support the level below vol=0 and it's not totally silent.

but it's not like 'not totally silent' but 'pretty loud'. On OSX volume scale is just fine.

ok, my comment was a rough guess which i experienced once (IIRC, it was a screamer). so let me know the chipset on your machine, shown in /proc/asound/cards. if it's tumbler or snapper, this behavior should be a bug of the driver.

Takashi