flooded by "CPU#0: Running in modulated clock mode"
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 8 lines · Alexey Mahotkin
Is that ok that the status is flapping?
Quoted 3 lines
Quoted 3 lines
CPU#0: Running in modulated clock mode
CPU#0: Temperature/speed normal
CPU#0: Temperature above thresholdOr is it so that CPU switches to MCM, instantly cools down, switches to normal speed, instantly heats up and so on?
Yes it doesn't modulate indefinitely, it means that your cooling is inadequate.
Quoted 7 lines
Quoted 3 lines
The threshold is set so that its below the
catastrophic shutdown threshold. so ~60C sounds right considering your processor will probably shutdown at 80C.Who did set that threshold and how could I change it? I'd like it to be ~72C, because the machine is 1U and the higher temperature is kind of "normal" there.
If i recall correctly it's hardware set, i'm not sure if BIOSes can modify that these days. One thing you may want to note is that in the modulated state the processor doesn't process interrupts and runs at a 50% clock duty cycle. So there is a large performance loss when its running in this mode. You really should consider looking into your cooling...
Hi!
Quoted 3 lines
If i recall correctly it's hardware set, i'm not sure if BIOSes can modify that these days. One thing you may want to note is that in the modulated state the processor doesn't process interrupts and runs at a 50% clock
No interrupts? That would mean almost dead machine. Are you sure?
Signature · 1 line
64 bytes from 195.113.31.123: icmp_seq=28 ttl=51 time=448769.1 ms
Quoted 9 lines · Pavel Machek
Hi!
Quoted 3 lines
If i recall correctly it's hardware set, i'm not sure if BIOSes can modify that these days. One thing you may want to note is that in the modulated state the processor doesn't process interrupts and runs at a 50% clock
No interrupts? That would mean almost dead machine. Are you sure?
Yep, it's normally 50% modulation for 1ms or until the temperature drops below threshold, whichever comes first with interrupts remaining pending.
Hi!
Quoted 9 lines
Quoted 6 lines
Quoted 3 lines
If i recall correctly it's hardware set, i'm not sure if BIOSes can modify that these days. One thing you may want to note is that in the modulated state the processor doesn't process interrupts and runs at a 50% clock
No interrupts? That would mean almost dead machine. Are you sure?
Yep, it's normally 50% modulation for 1ms or until the temperature drops below threshold, whichever comes first with interrupts remaining pending.
Ok, but that means (assuming machine is above treshold all the time) that interrupts are only delayed by milisecond, and that machine does no usefull work 50% of time, right?
Pavel
Signature · 2 lines
When do you have a heart between your knees? [Johanka's followup: and *two* hearts?]
Hi Pavel,
Quoted 7 lines · Pavel Machek
Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If i recall correctly it's hardware set, i'm not sure if BIOSes can modify that these days. One thing you may want to note is that in the modulated state the processor doesn't process interrupts and runs at a 50% clock
No interrupts? That would mean almost dead machine. Are you sure?
Quoted 6 lines
Quoted 2 lines
Yep, it's normally 50% modulation for 1ms or until the temperature drops below threshold, whichever comes first with interrupts remaining pending.
Ok, but that means (assuming machine is above treshold all the time) that interrupts are only delayed by milisecond, and that machine does no usefull work 50% of time, right?
Correct, it's actually not that observable on a non heavily loaded system.