Skip to contentSkip to conversation

hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

DISCUSSION Bob Gill 2 participants 3 messages May 6, 2004 – May 7, 2004

lore
Share & tools
lore

Bob Gill

author
#0 lore raw
Quoted 1 line

zero IDE changes in bk6 -> bk8 but a lot of ACPI / IRQ related

OK. My APIC is a SiS961.
I can't send data from 2.6.6-rc3-bk8, but from 2.6.6-rc3-bk6, /proc/acpi gives:
(/proc/acpi/processor/CPU0)

processor id:            0
acpi id:                 0
bus mastering control:   yes
power management:        no
throttling control:      no
limit interface:         no
<not supported>
active state:            C1
default state:           C1
bus master activity:     00000000

states:
*C1: promotion[--] demotion[--] latency[000]
usage[00000000]
C2: <not supported>
C3: <not supported>
<not supported>

cat /proc/acpi/sleep shows:
S0 S1 S4 S5
cat /proc/ide/sis shows:
SiS 5513 Ultra 100 chipset
--------------- Primary Channel ---------------- Secondary Channel
-------------

Channel Status: On                               On
Operation Mode: Compatible                       Compatible
Cable Type:     80 pins                          80 pins
Prefetch Count: 512                              512
Drive 0:        Postwrite Enabled                Postwrite Disabled
                Prefetch  Enabled                Prefetch  Disabled
                UDMA Enabled                     UDMA Enabled
                UDMA Cycle Time    3 CLK         UDMA Cycle Time    6

CLK
Data Active Time 3 PCICLK Data Active Time 3
PCICLK
Data Recovery Time 1 PCICLK Data Recovery Time 1
PCICLK

Drive 1:        Postwrite Enabled                Postwrite Disabled
                Prefetch  Enabled                Prefetch  Disabled
                UDMA Enabled                     UDMA Disabled
                UDMA Cycle Time    2 CLK         UDMA Cycle Time   

Reserved
Data Active Time 3 PCICLK Data Active Time 3
PCICLK
Data Recovery Time 1 PCICLK Data Recovery Time 3
PCICLK

... I don't know if any of this is helpful. The IRQ and IO address assignments (sent with my first email) are from 2.6.6-rc3-bk6.

Thanks,
Bob

#1 lore raw

Re: hdc: lost interrupt ide-cd: cmd 0x3 timed out ...

Quoted 1 line
Quoted 1 line

zero IDE changes in bk6 -> bk8 but a lot of ACPI / IRQ related

it's bk8 which broke sis961 (or revealed it native brokenness)

Quoted 1 line

OK. My APIC is a SiS961.

I have the same problem (and the same chipset).
Passing acpi=noirq helps to work it around.

author
#2 lore raw

Re: hdc: lost interrupt ide-cd: cmd 0x3 timed out ...

OK, great! Adding acpi=noirq to the kernel line made the lost interrupt problem go away, and getting rid of rhgb on the same line made the problems I had with nvidia drivers killing the system at the login prompt (white screen, no kbd response) go away.
One goes in, one goes out! ;)

Thanks,
Bob

Quoted 9 lines · Alex Riesen
Quoted 1 line
Quoted 1 line

zero IDE changes in bk6 -> bk8 but a lot of ACPI / IRQ related

it's bk8 which broke sis961 (or revealed it native brokenness)

Quoted 1 line

OK. My APIC is a SiS961.

I have the same problem (and the same chipset).
Passing acpi=noirq helps to work it around.