sata promise and software raid5...
Hello,
controller - Promise SATA 150 TX4, linux 2.6.7-rc1-bk1, HDD Maxtor 250Gb (x4)
Why so slowly reads (and writes) with software raid5?
gnome:~ # hdparm -t /dev/sda2
/dev/sda2:
Timing buffered disk reads: 148 MB in 3.01 seconds = 49.16 MB/sec
gnome:~ # hdparm -t /dev/sdb2
/dev/sdb2:
Timing buffered disk reads: 148 MB in 3.02 seconds = 49.01 MB/sec
gnome:~ # hdparm -t /dev/sdc2
/dev/sdc2:
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.90 MB/sec
gnome:~ # hdparm -t /dev/sdd2
/dev/sdd2:
Timing buffered disk reads: 144 MB in 3.00 seconds = 47.96 MB/sec
gnome:~ #
gnome:~ #
gnome:~ # hdparm -t /dev/md0
/dev/md0:
Timing buffered disk reads: 64 MB in 3.12 seconds = 20.52 MB/sec
gnome:~ #
gnome:~ # cat /etc/raidtab
raiddev /dev/md0
raid-level 5
nr-raid-disks 4
nr-spare-disks 0
persistent-superblock 1
parity-algorithm left-symmetric
chunk-size 1024 device /dev/sda2
raid-disk 0
device /dev/sdb2
raid-disk 1
device /dev/sdc2
raid-disk 2
device /dev/sdd2
raid-disk 3
bye
--
Hi,
I think I had the same problem on a PIIX SATA with RAID1. Basically, I noticed that each disk could be accessed one at a time, and that it was totally impossible to access the second one while the first one was reading. A simple "cat /dev/sda >/dev/null" prevented anyone from logging into the box or doing anything which required disk I/O.
So if you have the same problem, I can fairly understand your low numbers. Could you try something like :
# cat /dev/sda >/dev/null & # hdparm -t /dev/sdb
If hdparm doesn't start before the 'cat' ends, you do have the same problem. Well, I don't know where it comes from, and unfortunately I don't have the machine anymore to try fixes.
Regards,
Willy
Quoted 63 lines · Andrey Nekrasov
Hello,
controller - Promise SATA 150 TX4, linux 2.6.7-rc1-bk1, HDD Maxtor 250Gb (x4)
Why so slowly reads (and writes) with software raid5?
gnome:~ # hdparm -t
/dev/sda2
/dev/sda2:
Timing buffered disk reads: 148 MB in 3.01 seconds = 49.16 MB/sec
gnome:~ # hdparm -t/dev/sdb2
/dev/sdb2:
Timing buffered disk reads: 148 MB in 3.02 seconds = 49.01 MB/sec
gnome:~ # hdparm -t/dev/sdc2
/dev/sdc2:
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.90 MB/sec
gnome:~ # hdparm -t/dev/sdd2
/dev/sdd2:
Timing buffered disk reads: 144 MB in 3.00 seconds = 47.96 MB/sec
gnome:~ #
gnome:~ #
gnome:~ # hdparm -t/dev/md0
/dev/md0:
Timing buffered disk reads: 64 MB in 3.12 seconds = 20.52 MB/sec
gnome:~ #gnome:~ # cat
/etc/raidtab
raiddev/dev/md0raid-level 5 nr-raid-disks 4 nr-spare-disks 0 persistent-superblock 1 parity-algorithm left-symmetric chunk-size 1024device
/dev/sda2
raid-disk 0device
/dev/sdb2
raid-disk 1device
/dev/sdc2
raid-disk 2device
/dev/sdd2
raid-disk 3bye
---
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
You need to test all the disks running at once, this should give a much clearer picture of how the system will perform with a raid volume. a simple test is like so:
-> hdparm -t /dev/sda2 & hdparm -t /dev/sdc2 & hdparm -t /dev/sdc2 & hdparm -t /dev/sdd2
This will get them all going at once, but may jumble the output a bit.
Evan
Quoted 63 lines · Andrey Nekrasov
Hello,
controller - Promise SATA 150 TX4, linux 2.6.7-rc1-bk1, HDD Maxtor 250Gb (x4)
Why so slowly reads (and writes) with software raid5?
gnome:~ # hdparm -t
/dev/sda2
/dev/sda2:
Timing buffered disk reads: 148 MB in 3.01 seconds = 49.16 MB/sec
gnome:~ # hdparm -t/dev/sdb2
/dev/sdb2:
Timing buffered disk reads: 148 MB in 3.02 seconds = 49.01 MB/sec
gnome:~ # hdparm -t/dev/sdc2
/dev/sdc2:
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.90 MB/sec
gnome:~ # hdparm -t/dev/sdd2
/dev/sdd2:
Timing buffered disk reads: 144 MB in 3.00 seconds = 47.96 MB/sec
gnome:~ #
gnome:~ #
gnome:~ # hdparm -t/dev/md0
/dev/md0:
Timing buffered disk reads: 64 MB in 3.12 seconds = 20.52 MB/sec
gnome:~ #gnome:~ # cat
/etc/raidtab
raiddev/dev/md0raid-level 5 nr-raid-disks 4 nr-spare-disks 0 persistent-superblock 1 parity-algorithm left-symmetric chunk-size 1024device
/dev/sda2
raid-disk 0device
/dev/sdb2
raid-disk 1device
/dev/sdc2
raid-disk 2device
/dev/sdd2
raid-disk 3bye
---
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/