Skip to contentSkip to conversation

sata promise and software raid5...

DISCUSSION Andrey Nekrasov 3 participants 3 messages May 25, 2004 – May 26, 2004

lore
Share & tools
lore
#0 lore raw

Hello,

controller - Promise SATA 150 TX4, linux 2.6.7-rc1-bk1, HDD Maxtor 250Gb (x4)

Why so slowly reads (and writes) with software raid5?

gnome:~ # hdparm -t /dev/sda2

/dev/sda2:
Timing buffered disk reads: 148 MB in 3.01 seconds = 49.16 MB/sec
gnome:~ # hdparm -t /dev/sdb2

/dev/sdb2:
Timing buffered disk reads: 148 MB in 3.02 seconds = 49.01 MB/sec
gnome:~ # hdparm -t /dev/sdc2

/dev/sdc2:
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.90 MB/sec
gnome:~ # hdparm -t /dev/sdd2

/dev/sdd2:
Timing buffered disk reads: 144 MB in 3.00 seconds = 47.96 MB/sec
gnome:~ #
gnome:~ #
gnome:~ # hdparm -t /dev/md0

/dev/md0:
Timing buffered disk reads: 64 MB in 3.12 seconds = 20.52 MB/sec
gnome:~ #

gnome:~ # cat /etc/raidtab
raiddev /dev/md0

        raid-level              5
        nr-raid-disks           4
        nr-spare-disks          0
        persistent-superblock   1
        parity-algorithm        left-symmetric
        chunk-size              1024

device /dev/sda2
raid-disk 0

device /dev/sdb2
raid-disk 1

device /dev/sdc2
raid-disk 2

device /dev/sdd2
raid-disk 3

bye
--

#1 lore raw

Hi,

I think I had the same problem on a PIIX SATA with RAID1. Basically, I noticed that each disk could be accessed one at a time, and that it was totally impossible to access the second one while the first one was reading. A simple "cat /dev/sda >/dev/null" prevented anyone from logging into the box or doing anything which required disk I/O.

So if you have the same problem, I can fairly understand your low numbers. Could you try something like :

# cat /dev/sda >/dev/null &
# hdparm -t /dev/sdb

If hdparm doesn't start before the 'cat' ends, you do have the same problem. Well, I don't know where it comes from, and unfortunately I don't have the machine anymore to try fixes.

Regards,
Willy

Quoted 63 lines · Andrey Nekrasov

Hello,

controller - Promise SATA 150 TX4, linux 2.6.7-rc1-bk1, HDD Maxtor 250Gb (x4)

Why so slowly reads (and writes) with software raid5?

gnome:~ # hdparm -t /dev/sda2

/dev/sda2:
Timing buffered disk reads: 148 MB in 3.01 seconds = 49.16 MB/sec
gnome:~ # hdparm -t /dev/sdb2

/dev/sdb2:
Timing buffered disk reads: 148 MB in 3.02 seconds = 49.01 MB/sec
gnome:~ # hdparm -t /dev/sdc2

/dev/sdc2:
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.90 MB/sec
gnome:~ # hdparm -t /dev/sdd2

/dev/sdd2:
Timing buffered disk reads: 144 MB in 3.00 seconds = 47.96 MB/sec
gnome:~ #
gnome:~ #
gnome:~ # hdparm -t /dev/md0

/dev/md0:
Timing buffered disk reads: 64 MB in 3.12 seconds = 20.52 MB/sec
gnome:~ #

gnome:~ # cat /etc/raidtab
raiddev /dev/md0

        raid-level              5
        nr-raid-disks           4
        nr-spare-disks          0
        persistent-superblock   1
        parity-algorithm        left-symmetric
        chunk-size              1024

device /dev/sda2
raid-disk 0

device /dev/sdb2
raid-disk 1

device /dev/sdc2
raid-disk 2

device /dev/sdd2
raid-disk 3

bye
--

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#2 lore raw
In reply to Andrey Nekrasov

You need to test all the disks running at once, this should give a much clearer picture of how the system will perform with a raid volume. a simple test is like so:

-> hdparm -t /dev/sda2 & hdparm -t /dev/sdc2 & hdparm -t /dev/sdc2 & hdparm -t /dev/sdd2

This will get them all going at once, but may jumble the output a bit.

Evan

Quoted 63 lines · Andrey Nekrasov

Hello,

controller - Promise SATA 150 TX4, linux 2.6.7-rc1-bk1, HDD Maxtor 250Gb (x4)

Why so slowly reads (and writes) with software raid5?

gnome:~ # hdparm -t /dev/sda2

/dev/sda2:
Timing buffered disk reads: 148 MB in 3.01 seconds = 49.16 MB/sec
gnome:~ # hdparm -t /dev/sdb2

/dev/sdb2:
Timing buffered disk reads: 148 MB in 3.02 seconds = 49.01 MB/sec
gnome:~ # hdparm -t /dev/sdc2

/dev/sdc2:
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.90 MB/sec
gnome:~ # hdparm -t /dev/sdd2

/dev/sdd2:
Timing buffered disk reads: 144 MB in 3.00 seconds = 47.96 MB/sec
gnome:~ #
gnome:~ #
gnome:~ # hdparm -t /dev/md0

/dev/md0:
Timing buffered disk reads: 64 MB in 3.12 seconds = 20.52 MB/sec
gnome:~ #

gnome:~ # cat /etc/raidtab
raiddev /dev/md0

        raid-level              5
        nr-raid-disks           4
        nr-spare-disks          0
        persistent-superblock   1
        parity-algorithm        left-symmetric
        chunk-size              1024

device /dev/sda2
raid-disk 0

device /dev/sdb2
raid-disk 1

device /dev/sdc2
raid-disk 2

device /dev/sdd2
raid-disk 3

bye
--

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/