Skip to contentSkip to conversation

MPC5200 + multi serial chips (16554)

U-Boot-Users Andrea Sorio 2 participants 4 messages Feb 1, 2005

lore
Share & tools
lore
#0 lore raw

Hi

I have to develop an embedded system with a MPC5200 and eight 16554 (32 serial ports). I'll use a chip seletec to manage the eight multi serial chips
with an external CPLD.
May I manage the serial ports with setserial linux program or I have to develop a new device driver?

Thank you in advance

Best Regards

Andrea Sorio

Signature · 5 lines
Ing. Andrea Sorio
Hardware & Software Engineer
Freelance
email: a.sorio at cocay.it
Phone: 348 8703449
#1 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

I have to develop an embedded system with a MPC5200 and eight 16554 (32 serial ports). I'll use a chip seletec to manage the

Do you need to support all these 8 UART ports in _U-Boot_ ???

Quoted 2 lines

May I manage the serial ports with setserial linux program or I have to develop a new device driver?

seterial is an application program that requires an OS to run. It won't help you for U-Boot. [Yes, this is the U-Boot mailing list, and we're discussing U-Boot issues here.]

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Beware of programmers carrying screwdrivers."      - Chip Salzenberg
#2 lore raw

Dear Wolfgang

Thank you for your replay.

Quoted 8 lines
Quoted 4 lines

I have to develop an embedded system with a MPC5200 and eight 16554 (32 serial ports). I'll use a chip seletec to manage the

Do you need to support all these 8 UART ports in _U-Boot_ ???

No, I don't need them in U-Boot.

Quoted 10 lines
Quoted 4 lines

May I manage the serial ports with setserial linux program or I have to develop a new device driver?

seterial is an application program that requires an OS to run. It won't help you for U-Boot. [Yes, this is the U-Boot mailing list, and we're discussing U-Boot issues here.]

Yes, I know.
I would like to install u-boot and linux embedded in this board. I hope that setserial could set up the linux serial device driver to manage the 32 serial
ports without any changes on serial driver. (I apologize for my english)

Thank you

Best regards

Andrea Sorio

Signature · 5 lines
Ing. Andrea Sorio
Hardware & Software Engineer
Freelance
email: a.sorio at cocay.it
Phone: 348 8703449
#3 lore raw

Dear Andrea,

Quoted 2 lines · in message <[email protected]> you wrote:

No, I don't need them in U-Boot.

Then this is actually off topic here.

Quoted 4 lines

I would like to install u-boot and linux embedded in this board. I hope that setserial could set up the linux serial device driver to manage the 32 serial
ports without any changes on serial driver. (I apologize for my english)

Your English is adequate.

Don;t expect setserial to be of any help on a non-x86 system. You will have to tweak at least the mapping for the serial driver in Linux. But as I said, this is off topic here.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
What about WRITING it first and rationalizing it afterwords?  :-)
                       - Larry Wall in <[email protected]>