Skip to contentSkip to conversation

fb support for au1x000

U-Boot-Users Rodolfo Giometti 2 participants 5 messages Jul 4, 2006

lore
Share & tools
lore
#0 lore raw

Hello,

I'm trying to add support for frame buffer to my au1100 based board but I'm a bit confused where I can allocate the frame buffer memory.

Looking at "lib_mips/board.c" I see:

        /*
         * Now that we have DRAM mapped and working, we can
         * relocate the code and continue running from DRAM.
         */
        addr = CFG_SDRAM_BASE + gd->ram_size;

        /* We can reserve some RAM "on top" here.
         */

        /* round down to next 4 kB limit.
         */
        addr &= ~(4096 - 1);
        debug ("Top of RAM usable for U-Boot at: %08lx\n", addr);

        /* Reserve memory for U-Boot code, data & bss
         * round down to next 16 kB limit
         */
        addr -= len;
        addr &= ~(16 * 1024 - 1);

        debug ("Reserving %ldk for U-Boot at: %08lx\n", len >> 10, addr);

Where "len" is:

	len = (ulong)&uboot_end - CFG_MONITOR_BASE;

So I think I can redefine "len" as follow:

	len = (ulong)&uboot_end - CFG_MONITOR_BASE + LCD_MEMORY_SIZE + PAGE_SIZE;

and then adding the code:

        /* configure available FLASH banks */
        size = flash_init();
        display_flash_config (size);

#ifdef CONFIG_LCD
# ifndef PAGE_SIZE
# define PAGE_SIZE 4096
# endif

        /*
         * reserve memory for LCD display (always full pages)
         */
        /* bss_end is defined in the board-specific linker script */
        addr = (uboot_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
        size = lcd_setmem (addr);
        gd->fb_base = addr;

#endif /* CONFIG_LCD */

        bd = gd->bd;
        bd->bi_flashstart = CFG_FLASH_BASE;
        bd->bi_flashsize = size;

to the function board_init_r().

Is that sane?

Ciao,

Rodolfo

Signature · 4 lines
GNU/Linux Solutions                  e-mail:    giometti at enneenne.com
Linux Device Driver                             giometti at gnudd.com
Embedded Systems                     		giometti at linux.it
UNIX programming                     phone:     +39 349 2432127
#1 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

I'm trying to add support for frame buffer to my au1100 based board but I'm a bit confused where I can allocate the frame buffer memory.

General rule: it's goot to allocate it at the upper end of memory, as we can then pass it unchanged to Linux. See how this is done in other architectures.

Quoted 1 line

Looking at "lib_mips/board.c" I see:

...

Quoted 2 lines
        /* We can reserve some RAM "on top" here.
         */

This is the right place.

Quoted 2 lines
        /* round down to next 4 kB limit.
         */

...

Quoted 1 line

Is that sane?

Maybe sane, but IMHO not optimal.

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
People have one thing in common: they are all different.
#2 lore raw

A little question.. is possible to use the u-boot serial console with the LCD support enabled? =:-o

Thanks,

Rodolfo

Signature · 11 lines
GNU/Linux Solutions                  e-mail:    giometti at enneenne.com
Linux Device Driver                             giometti at gnudd.com
Embedded Systems                     		giometti at linux.it
UNIX programming                     phone:     +39 349 2432127
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: Digital signature
Url : http://lists.denx.de/pipermail/u-boot/attachments/20060704/b9f87b90/attachment.pgp 
#3 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

A little question.. is possible to use the u-boot serial console with the LCD support enabled? =:-o

Yes, of course. Like any other output device.

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Where shall I begin, please your Majesty?" he asked. "Begin  at  the
beginning,"  the  King said, gravely, "and go on till you come to the
end: then stop."    - Alice's Adventures in Wonderland, Lewis Carroll
#4 lore raw
Quoted 2 lines · Wolfgang Denk

Yes, of course. Like any other output device.

I noticed that some boards use function console_assign() to set stdin, stdout and stderr devices. This function is called into last_stage_init() which is not defined for MIPS arch.

Should I add this function into "lib_mips/board.c" file or the above function may be called from another place?

Ciao,

Rodolfo

Signature · 11 lines
GNU/Linux Solutions                  e-mail:    giometti at enneenne.com
Linux Device Driver                             giometti at gnudd.com
Embedded Systems                     		giometti at linux.it
UNIX programming                     phone:     +39 349 2432127
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: Digital signature
Url : http://lists.denx.de/pipermail/u-boot/attachments/20060704/47351ba1/attachment.pgp