Patch to make VIA sata board bootable again.
Hello
The quirks.c update that went into 2.6.16.17 made an VIA machine here non bootable from an sata drive (via_sata), the error is:
"ATA1 qc timout"
"Failed to set xfermode".
And later kernel panic becouse no sata disk was found.
I tracked it down to the quirk update in 2.6.16.17. Below is a patch against 2.6.17.11 that reverses the uppdate and makse the system bootable again.
Another option is to find out the PCI_DEVICE_ID_VIA for the motherboard in question but I could not get that info. Dose someone have an idea how to find that info? then I can provide an patch that adds the right PCI_DEVICE_ID_VIA for my motherboard.
drivers/pci/quirks.c +1 -7
@@ -652,13 +652,7 @@pci_write_config_byte (dev,PCI_INTERRUPT_LINE , new_irq); } } -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_0 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_1 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_2 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_3 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686_4 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686_5 , quirk_via_irq); +DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_ANY_ID , quirk_via_irq);/* * VIA VT82C598 has its device ID settable and many BIOSes
Quoted 9 lines · On Fri, 01 Sep 2006 11:15:17 +0300 Johnny Strom <[email protected]> wrote:
Hello
The
quirks.cupdate that went into 2.6.16.17 made an VIA machine here non bootable from an sata drive (via_sata), the error is:"ATA1 qc timout"
"Failed to set xfermode".
argh.
Does 2.6.18-rc5 work?
Quoted 30 lines
And later kernel panic becouse no sata disk was found.
I tracked it down to the quirk update in 2.6.16.17. Below is a patch against 2.6.17.11 that reverses the uppdate and makse the system bootable again.Another option is to find out the
PCI_DEVICE_ID_VIAfor the motherboard in question but I could not get that info. Dose someone have an idea how to find that info? then I can provide an patch that adds the rightPCI_DEVICE_ID_VIAfor my motherboard.diff -ur
linux-2.6.17.11-org/drivers/pci/quirks.clinux-2.6.17.11/drivers/pci/quirks.c
---linux-2.6.17.11-org/drivers/pci/quirks.c2006-09-01
10:38:31.135747500 +0300
+++linux-2.6.17.11/drivers/pci/quirks.c2006-09-01 10:42:28.870605000 +0300(quoted diff) +0
-5@@ -652,13 +652,7 @@ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686,
Quoted 7 lines
quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_DEVICE_ID_VIA_82C686_4,quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_DEVICE_ID_VIA_82C686_5,quirk_via_irq);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_ANY_ID,quirk_via_irq);
That's wordwrapped.
Quoted 9 lines · Andrew Morton
Quoted 5 lines · On Fri, 01 Sep 2006 11:15:17 +0300 Johnny Strom <[email protected]> wrote:
Hello
The
quirks.cupdate that went into 2.6.16.17 made an VIA machine here non bootable from an sata drive (via_sata), the error is:
Quoted 8 lines
Quoted 2 lines
"ATA1 qc timout"
"Failed to set xfermode".argh.
Does 2.6.18-rc5 work?
No it is the same problem with 2.6.18-rc5.
Quoted 9 lines
Quoted 5 lines
And later kernel panic becouse no sata disk was found.
I tracked it down to the quirk update in 2.6.16.17. Below is a patch against 2.6.17.11 that reverses the uppdate and makse the system bootable again.Another option is to find out the
PCI_DEVICE_ID_VIAfor the motherboard in question but I could not get that info. Dose someone have an idea how to find that info? then I can provide an patch that adds the rightPCI_DEVICE_ID_VIAfor my motherboard.That's wordwrapped.
Attached an new diff.
Johnny
drivers/pci/quirks.c +1 -7
@@ -652,13 +652,7 @@pci_write_config_byte (dev,PCI_INTERRUPT_LINE , new_irq); } } -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_0 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_1 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_2 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_3 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686_4 , quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686_5 , quirk_via_irq); +DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_ANY_ID , quirk_via_irq);/* * VIA VT82C598 has its device ID settable and many BIOSes
Quoted 1 line · Johnny Strom
No it is the same problem with 2.6.18-rc5.
Did either the patches from Daniel Drake or Sergio Monteiro Basto help?
Quoted 1 line
Attached an new diff.
Which breaks other a different class of machines. A can you try -mm, there is a patch in that and tell us if that works?
Quoted 10 lines · Chris Wedgwood
Quoted 1 line · Johnny Strom
No it is the same problem with 2.6.18-rc5.
Did either the patches from Daniel Drake or Sergio Monteiro Basto help?
hello
I have now tested the patch found here:
http://lkml.org/lkml/2006/9/3/148
And that patchs works fine, I can now boot the system.
I have also tested this patch pci-quirk_via_irq-behaviour-change.patch and it works fine as well, I can boot the system again.
It is kernel version 2.6.17.11 that I have tested the patches on.
So any of those two patches makes my system boot again.
Johnny
Signature · 1 line
VGER BF report: H 0
Hi, Can you give me the information of interrupts
cat /proc/interrupts
XT_PIC or IO-APIC-edge/level ?
Quoted 57 lines · Johnny Strom
Hello
The
quirks.cupdate that went into 2.6.16.17 made an VIA machine here non bootable from an sata drive (via_sata), the error is:"ATA1 qc timout"
"Failed to set xfermode".And later kernel panic becouse no sata disk was found.
I tracked it down to the quirk update in 2.6.16.17. Below is a patch against 2.6.17.11 that reverses the uppdate and makse the system bootable again.Another option is to find out the
PCI_DEVICE_ID_VIAfor the motherboard in question but I could not get that info. Dose someone have an idea how to find that info? then I can provide an patch that adds the rightPCI_DEVICE_ID_VIAfor my motherboard.diff -ur
linux-2.6.17.11-org/drivers/pci/quirks.clinux-2.6.17.11/drivers/pci/quirks.c
---linux-2.6.17.11-org/drivers/pci/quirks.c2006-09-01
10:38:31.135747500 +0300
+++linux-2.6.17.11/drivers/pci/quirks.c2006-09-01 10:42:28.870605000 +0300(quoted diff) +0
-5@@ -652,13 +652,7 @@ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686,
quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_DEVICE_ID_VIA_82C686_4,quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_DEVICE_ID_VIA_82C686_5,quirk_via_irq);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_ANY_ID,quirk_via_irq);/*
* VIA VT82C598 has its device ID settable and many BIOSesSigned-off-by [email protected]-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines · Sergio Monteiro Basto
Hi, Can you give me the information of interrupts cat
/proc/interrupts
XT_PICor IO-APIC-edge/level ?
Here it is.
cat /proc/interrupts
CPU0
0: 1692278 XT-PIC timer 1: 40 XT-PIC i8042 2: 0 XT-PIC cascade 7: 414568 XT-PIC libata, ohci1394, uhci_hcd:usb2, uhci_hcd:usb3, radeon@pci:0000:01:00.0 8: 4 XT-PIC rtc 9: 0 XT-PIC acpi 10: 534456 XT-PIC sk98lin, ehci_hcd:usb1, VIA8237, eth0 11: 0 XT-PIC uhci_hcd:usb4, uhci_hcd:usb5 12: 130 XT-PIC i8042 14: 53 XT-PIC ide0 15: 101 XT-PIC ide1 NMI: 0 ERR: 0
Johnny
Quoted 54 lines · Johnny Strom
Quoted 50 lines
Hello
The
quirks.cupdate that went into 2.6.16.17 made an VIA machine here non bootable from an sata drive (via_sata), the error is:"ATA1 qc timout"
"Failed to set xfermode".And later kernel panic becouse no sata disk was found.
I tracked it down to the quirk update in 2.6.16.17. Below is a patch against 2.6.17.11 that reverses the uppdate and makse the system bootable again.Another option is to find out the
PCI_DEVICE_ID_VIAfor the motherboard in question but I could not get that info. Dose someone have an idea how to find that info? then I can provide an patch that adds the rightPCI_DEVICE_ID_VIAfor my motherboard.diff -ur
linux-2.6.17.11-org/drivers/pci/quirks.clinux-2.6.17.11/drivers/pci/quirks.c
---linux-2.6.17.11-org/drivers/pci/quirks.c2006-09-01
10:38:31.135747500 +0300
+++linux-2.6.17.11/drivers/pci/quirks.c2006-09-01 10:42:28.870605000 +0300(quoted diff) +0
-5@@ -652,13 +652,7 @@ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686,
quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_DEVICE_ID_VIA_82C686_4,quirk_via_irq);
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_DEVICE_ID_VIA_82C686_5,quirk_via_irq);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA,PCI_ANY_ID,quirk_via_irq);/*
* VIA VT82C598 has its device ID settable and many BIOSesSigned-off-by [email protected]-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/