Skip to contentSkip to conversation

Can I write to flash using mw command

U-Boot-Users bilahari akkiraju 3 participants 3 messages Oct 3, 2006 – Oct 5, 2006

lore
Share & tools
lore
#0 lore raw

Hello,

-> On my target board I have a spansion GL064M flash
device.

-> The flash base address is 0xff000000.

-> I have read the data sheet for the device and
noted down the erase and write command sequences for the device.

-> I cannot erase, write to flash by implementing the
appropriate command sequences with mw (memory write ) command provided by u-boot that came with my sdk (u-boot 1.1.4).

For example

For erasing sector 0xff000000 I typed the following
sector erase command sequence (as per data sheet) at u-boot prompt

mw.b 0xff000555 0xAA
mw.b 0xff0002AA 0x55
mw.b 0xff000555 0x80
mw.b 0xff000555 0xAA
mw.b 0xff0002AA 0x55
mw.b 0xff000000 0x30

For writing to address 0xff000000 I typed the
following write command sequence (as per data sheet) at the u-boot prompt.

mw.b 0xff000555 0xAA
mw.b 0xff0002AA 0x55
mw.b 0xff000555 0xA0

mw.b 0xff000000 0x12  ; value 0x12
mw.b 0xff000001 0x34  ; value 0x34
mw.b 0xff000000 0xF0  ; reset (I do it as u-boot

driver cfi_flash.c does it )

-> After doing all this , when I do a memory dump
using md.b 0xff000000 , to my frustration I see that nothing at all has happend to the flash.

I am sure I am missing something small or may be I am
doing a completely wrong thing. I am more of a computer science guy and new to chip programming. Any suggestions, ideas or comments would be very helpful.

Thanks you all

Bilahari

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

#1 lore raw
Quoted 4 lines · bilahari akkiraju

Hello,

-> On my target board I have a spansion GL064M flash
device.

We use this chip too and it works fine using U-boot's CFI. What is your sector layout (uniform, bottom boot or top boot)? The additional markings on the chip will tell you.

Quoted 5 lines

-> I cannot erase, write to flash by implementing the
appropriate command sequences with mw (memory write ) command provided by u-boot that came with my sdk (u-boot 1.1.4).

Do the U-boot 'protect' and 'erase commands work? If so, why torture yourself with low-level access? If not, you have a configuration or hardware issue which we can explore.

regards,
Ben

#2 lore raw
In reply to bilahari akkiraju
Quoted 3 lines · In message <[email protected]> you wrote:

-> On my target board I have a spansion GL064M flash
device.

How is it attached? As a 8 bit device?

Quoted 2 lines

-> I cannot erase, write to flash by implementing the
appropriate command sequences with mw (memory write )

Are you sure you use ther correct addresses and commands?

Quoted 10 lines

For erasing sector 0xff000000 I typed the following
sector erase command sequence (as per data sheet) at u-boot prompt

mw.b 0xff000555 0xAA
mw.b 0xff0002AA 0x55
mw.b 0xff000555 0x80
mw.b 0xff000555 0xAA
mw.b 0xff0002AA 0x55
mw.b 0xff000000 0x30

Are you really accessing an 8 bit device?

Quoted 2 lines

I am sure I am missing something small or may be I am
doing a completely wrong thing. I am more of a

Also check if your memory controller is set up correctly...

Best regards,

Wolfgang Denk

Signature · 6 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
All repairs tend to destroy the structure, to  increase  the  entropy
and  disorder  of the system. Less and less effort is spent on fixing
original design flaws; more and more is spent on fixing flaws  intro-
duced by earlier fixes.       - Fred Brooks, "The Mythical Man Month"