update MTD OF implementation
Subsystems (2)
PATCH 1/1 update MTD OF implementation
Hello folks,
the patch below updates the powerpc part of the MTD OF implementation with the new field probe-type and also fixes the typos/build warning for rom.c. So therefore it in a way supersedes the patch from Geoff which can be seen at http://ozlabs.org/pipermail/linuxppc-dev/2006-December/028831.html.
Documentation/powerpc/booting-without-of.txt | 19 +++++++++++-------- arch/powerpc/sysdev/rom.c | 1 + 2 files changed, 12 insertions(+), 8 deletions(-)
Documentation/powerpc/booting-without-of.txt +11 -8
@@ -1703,29 +1703,32 @@ platforms are moved over to use the flat Required properties: - device_type : has to be "rom" - - compatible : Should specify what this ROM device is compatible with - (i.e. "onenand"). Currently, this is most likely to be "direct-mapped" - (which corresponds to the MTD physmap mapping driver). - - regs : Offset and length of the register set (or memory mapping) for + - compatible : Should specify what this flash device is compatible with. + Currently, this is most likely to be "direct-mapped" (which + corresponds to the MTD physmap mapping driver). + - reg : Offset and length of the register set (or memory mapping) for the device. + - bank-width : Width of the flash data bus in bytes. Required + for the NOR flashes (compatible == "direct-mapped" and others) ONLY. Recommended properties : - - bank-width : Width of the flash data bus in bytes. Required - for the NOR flashes (compatible == "direct-mapped" and others) ONLY. - partitions : Several pairs of 32-bit values where the first value is partition's offset from the start of the device and the second one is partition size in bytes with LSB used to signify a read only - partititon (so, the parition size should always be an even number). + partition (so, the parition size should always be an even number). - partition-names : The list of concatenated zero terminated strings representing the partition names. + - probe-type : The type of probe which should be done for the chip + (JEDEC vs CFI actually). Valid ONLY for NOR flashes. Example: flash@ff000000 { device_type = "rom"; compatible = "direct-mapped"; - regs = <ff000000 01000000>; + probe-type = "CFI"; + reg = <ff000000 01000000>; bank-width = <4>; partitions = <00000000 00f80000 00f80000 00080001>;
arch/powerpc/sysdev/Makefile +0 -0
arch/powerpc/sysdev/rom.c +1 -0
@@ -9,6 +9,7 @@#include <linux/kernel.h> #include <asm/of_device.h> +#include <asm/of_platform.h> static int __init powerpc_flash_init (void ) {
Hello.
Quoted 8 lines · Vitaly Wool
the patch below updates the powerpc part of the MTD OF implementation with the new field probe-type and also fixes the typos/build warning for
rom.c. So therefore it in a way supersedes the patch from Geoff which can be seen at http://ozlabs.org/pipermail/linuxppc-dev/2006-December/028831.html.Documentation/powerpc/booting-without-of.txt | 19 +++++++++++-------- arch/powerpc/sysdev/rom.c | 1 + 2 files changed, 12 insertions(+), 8 deletions(-)Signed-off-by Vitaly Wool <[email protected]>
Quoted 51 lines
Documentation/powerpc/booting-without-of.txt +11
-8@@ -1703,29 +1703,32 @@ platforms are moved over to use the flat Required properties: - device_type : has to be "rom" - - compatible : Should specify what this ROM device is compatible with - (i.e. "onenand"). Currently, this is most likely to be "direct-mapped" - (which corresponds to the MTD physmap mapping driver). - - regs : Offset and length of the register set (or memory mapping) for + - compatible : Should specify what this flash device is compatible with. + Currently, this is most likely to be "direct-mapped" (which + corresponds to the MTD physmap mapping driver). + - reg : Offset and length of the register set (or memory mapping) for the device. + - bank-width : Width of the flash data bus in bytes. Required + for the NOR flashes (compatible == "direct-mapped" and others) ONLY. Recommended properties : - - bank-width : Width of the flash data bus in bytes. Required - for the NOR flashes (compatible == "direct-mapped" and others) ONLY. - partitions : Several pairs of 32-bit values where the first value is partition's offset from the start of the device and the second one is partition size in bytes with LSB used to signify a read only - partititon (so, the parition size should always be an even number). + partition (so, the parition size should always be an even number). - partition-names : The list of concatenated zero terminated strings representing the partition names. + - probe-type : The type of probe which should be done for the chip + (JEDEC vs CFI actually). Valid ONLY for NOR flashes. Example: flash@ff000000 { device_type = "rom"; compatible = "direct-mapped"; - regs = <ff000000 01000000>; + probe-type = "CFI"; + reg = <ff000000 01000000>; bank-width = <4>; partitions = <00000000 00f80000 00f80000 00080001>;arch/powerpc/sysdev/Makefile +0
-0arch/powerpc/sysdev/rom.c +0
-0
arch/powerpc/sysdev/rom.c line 15
Quoted 7 lines
arch/powerpc/sysdev/rom.c +1
-0@@ -9,6 +9,7 @@#include <linux/kernel.h> #include <asm/of_device.h> +#include <asm/of_platform.h> static int __init powerpc_flash_init (void ) {
WBR, Sergei
Quoted 10 lines · On Tue, 12 Dec 2006 00:58:29 +0300 Sergei Shtylyov wrote:
Hello.
Quoted 6 lines · Vitaly Wool
the patch below updates the powerpc part of the MTD OF implementation with the new field probe-type and also fixes the typos/build warning for
rom.c. So therefore it in a way supersedes the patch from Geoff which can be seen at
http://ozlabs.org/pipermail/linuxppc-dev/2006-December/028831.html.
Quoted 7 lines
Quoted 5 lines
Documentation/powerpc/booting-without-of.txt | 19+++++++++++--------
arch/powerpc/sysdev/rom.c
| 1 + 2 files changed, 12 insertions(+), 8 deletions(-)Signed-off-by Vitaly Wool <[email protected]>Acked-by Sergei Shtylyov <[email protected]>
Quoted 74 lines
Quoted 61 lines
(quoted diff) +0
-0
b/Documentation/powerpc/booting-without-of.txtindex b3bd366..3399427 100644 ---a/Documentation/powerpc/booting-without-of.txt+++b/Documentation/powerpc/booting-without-of.txt@@ -1703,29 +1703,32 @@ platforms are moved over to use the flat Required properties:-
device_type: has to be "rom"
- - compatible : Should specify what this ROM device is
compatible with
- (i.e. "onenand"). Currently, this is most likely to be
"direct-mapped"(quoted diff) +0
-2- (which corresponds to the MTD physmap mapping driver). - - regs : Offset and length of the register set (or memorymapping) for
+ - compatible : Should specify what this flash device is
compatible with.Documentation/powerpc/booting-without-of.txt +3
-0+ Currently, this is most likely to be "direct-mapped" (which + corresponds to the MTD physmap mapping driver). + - reg : Offset and length of the register set (or memorymapping) for the device.
(quoted diff) +2
-0+ - bank-width : Width of the flash data bus in bytes. Required + for the NOR flashes (compatible == "direct-mapped" andothers) ONLY.
Recommended properties :(quoted diff) +0
-2- - bank-width : Width of the flash data bus in bytes. Required - for the NOR flashes (compatible == "direct-mapped" andothers) ONLY.
- partitions : Several pairs of 32-bit values where the first
value is partition's offset from the start of the device and the second one is partition size in bytes with LSB used to signify a read only
- partititon (so, the parition size should always be an even
number).
+ partition (so, the parition size should always be an even
number).
- partition-names : The list of concatenated zero terminated
strings representing the partition names.
+ - probe-type : The type of probe which should be done for the
chipDocumentation/powerpc/booting-without-of.txt +3
-1+ (JEDEC vs CFI actually). Valid ONLY for NOR flashes. Example: flash@ff000000 { device_type = "rom"; compatible = "direct-mapped"; - regs = <ff000000 01000000>; + probe-type = "CFI"; + reg = <ff000000 01000000>; bank-width = <4>; partitions = <00000000 00f80000 00f80000 00080001>;(quoted diff) +0
-0b/arch/powerpc/sysdev/Makefile diff --git
a/arch/powerpc/sysdev/rom.cb/arch/powerpc/sysdev/rom.cindex bf5b3f1..c855a3b 100644 ---a/arch/powerpc/sysdev/rom.c+++b/arch/powerpc/sysdev/rom.carch/powerpc/sysdev/rom.c line 15
Quoted 7 lines
arch/powerpc/sysdev/rom.c +1
-0@@ -9,6 +9,7 @@#include <linux/kernel.h> #include <asm/of_device.h> +#include <asm/of_platform.h> static int __init powerpc_flash_init (void ) {WBR, Sergei
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev
Signature · 1 line
Sincerely, Vitaly