Skip to contentSkip to conversation

HPT36x PCI clock detection fix

PATCH In review Sergei Shtylyov 2 participants 2 messages Dec 30, 2006 – Jan 2, 2007 libata

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 HPT36x PCI clock detection fix

Fix minor coding mistake in the HPT36x PCI clock detection code noticed by Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing 'break' statements. This, however, most probably never mattered -- in fact, I was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e. supported only 33 MHz PCI.

Note that in the original driver there was another bug: 25 and 40 MHz cases were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks, a lower clock count just *cannot* correspond to a higher frequency, i. e. it should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around.

 drivers/ide/pci/hpt366.c |    8 ++++++--
 1 files changed, 6 insertions(+), 2 deletions(-)
drivers/ide/pci/hpt366.c +6 -2
Index: linux-2.6/drivers/ide/pci/hpt366.c
===================================================================
@@ -1,5 +1,5 @@
 /*
- * linux/drivers/ide/pci/hpt366.c		Version 1.00	Jun 25, 2006
+ * linux/drivers/ide/pci/hpt366.c		Version 1.01	Dec 23, 2006
  *
  * Copyright (C) 1999-2003		Andre Hedrick <[email protected]>
  * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
@@ -107,7 +107,8 @@
  *   frequency
  * - switch to using the  DPLL clock and enable UltraATA/133 mode by default on
  *   anything  newer than HPT370/A
- * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366();
+ * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
+ *   also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips;
  *   unify HPT36x/37x timing setup code and the speedproc handlers by joining
  *   the register setting lists into the table indexed by the clock selected
  *	Sergei Shtylyov, <[email protected]> or <[email protected]>
@@ -1125,11 +1126,14 @@ static unsigned int __devinit init_chips
 		switch((itr1 >> 8) & 0x07) {
 			case 0x09:
 				pci_clk = 40;
+				break;
 			case 0x05:
 				pci_clk = 25;
+				break;
 			case 0x07:
 			default:
 				pci_clk = 33;
+				break;
 		}
 	}
 
Acked-by on v1 1/1
#1 lore raw
Quoted 7 lines · Sergei Shtylyov

Fix minor coding mistake in the HPT36x PCI clock detection code noticed by Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing 'break' statements. This, however, most probably never mattered -- in fact, I was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e. supported only 33 MHz PCI.

Quoted 6 lines

Note that in the original driver there was another bug: 25 and 40 MHz cases were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks, a lower clock count just *cannot* correspond to a higher frequency, i. e. it should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around.