Skip to contentSkip to conversation

bad temperature values from w83781d in 2.6.22

PATCH In review Joerg Sommrey 4 participants 10 messages Aug 5, 2007 – Aug 12, 2007 Hardware monitoring

lore
Share & tools
lore
#0 lore raw

Hi,

after upgrading from 2.6.21 to 2.6.22 the CPU temperatures shown by w83781d look unreal. They were in a range from 40°C when idle to 75°C under full load with 2.6.21. The values shown now are in a very small range from 77°C to 82°C. From the (low) noise of the fan I can tell that the temperature is <50°C.
The third temperature shown is completely wrong.

I have a Tyan Tiger MPX board with a w83782d chip. Output from "sensors":

w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0

 +5 V:     +4.81 V  (min =  +4.76 V, max =  +5.24 V)
3 VSB:     +3.30 V  (min =  +2.85 V, max =  +3.15 V)       ALARM
chs3 Fan: 2122 RPM  (min = 2657 RPM, div = 4)              ALARM

VRM2 Temp: -208°C (high = -176°C, hyst = -181°C) sensor = transistor
CPU1 Temp: +78.5°C (high = +80°C, hyst = +75°C) sensor = transistor ALARM
CPU2 Temp: +77.5°C (high = +80°C, hyst = +75°C) sensor = transistor ALARM
alarms:
beep_enable:
Sound alarm enabled

# cat /sys/bus/i2c/devices/0-002d/temp*_input
-209000
77500
77500

Any ideas?

-jo

Signature · 1 line
-rw-r--r-- 1 jo users 62 2007-08-04 14:02 /home/jo/.signature
#1 lore raw
Quoted 7 lines · Joerg Sommrey

after upgrading from 2.6.21 to 2.6.22 the CPU temperatures shown by w83781d look unreal. They were in a range from 40°C when idle to 75°C under full load with 2.6.21. The values shown now are in a very small range from 77°C to 82°C. From the (low) noise of the fan I can tell that the temperature is <50°C.
The third temperature shown is completely wrong.

Quoted 5 lines

I have a Tyan Tiger MPX board with a w83782d chip. Output from "sensors":

w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0

As a datapoint, the same W83782D on AMD756 (also I2C) works correctly with 2.6.22:

w83782d-i2c-0-2d
Adapter: SMBus AMD756 adapter at 50e0

Jean Delvare recently worked on the ISA interface to these chips but it seems this would not be the cause if you are also using I2C. Our hardware appears rather identical...

I've attached (an excerpt of) my /etc/sensors.conf -- I once dug through the datasheets for those compute lines for example so perhaps its still useful even if 2.6.21 working for you probably means you don't have a config problem.

Rene.

w83782d-i2c-0-2d

Adapter: SMBus AMD756 adapter at 50e0
Vcore:     +1.79 V  (min =  +1.74 V, max =  +1.86 V)              (beep)
Vcache:    +2.54 V  (min =  +2.26 V, max =  +2.75 V)              (beep)
Vcc3:      +3.38 V  (min =  +2.98 V, max =  +3.63 V)              (beep)
+5V:       +4.92 V  (min =  +4.49 V, max =  +5.51 V)              (beep)
+12V:     +12.28 V  (min = +10.82 V, max = +13.19 V)              (beep)
-12V:     -12.28 V  (min = -14.42 V, max =  -9.57 V)              (beep)
-5V:       -5.45 V  (min =  -6.00 V, max =  -3.99 V)              (beep)
+5V SB:    +5.16 V  (min =  +4.49 V, max =  +5.51 V)              (beep)
Battery:   +3.31 V  (min =  +2.40 V, max =  +3.60 V)              (beep)
Sys Fan:  1548 RPM  (min = 1350 RPM, div = 4)                     (beep)
CPU Fan:  2191 RPM  (min = 1985 RPM, div = 4)                     (beep)
Sys Temp:    +47°C  (high =   +55°C, hyst =   +52°C)   sensor = thermistor           (beep)
CPU Temp:  +48.5°C  (high =   +60°C, hyst =   +57°C)   sensor = thermistor           (beep)
vid:      +1.750 V  (VRM Version 9.0)

alarms:
beep_enable:
Sound alarm enabled

# Gigabyte GA-7IXE4
chip "w83782d-*"

# BIOS labels

    label in0 "Vcore"
    label in1 "Vcache"
    label in2 "Vcc3"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "-12V"
    label in6 "-5V"
    label in7 "+5V SB"
    label in8 "Battery"

# W83782D datasheet

    compute in3 @ * (34 + 50) / 50 , @ * 50 / (34 + 50)
    compute in4 @ * (28 + 10) / 10 , @ * 10 / (28 + 10)
    compute in5 (@ - 3.6) * (232 + 56) / 56 + 3.6 , (@ - 3.6) * 56 / (232 + 56) + 3.6
    compute in6 (@ - 3.6) * (120 + 56) / 56 + 3.6 , (@ - 3.6) * 56 / (120 + 56) + 3.6
    compute in7 @ * (34 + 50) / 50 , @ * 50 / (34 + 50)

# Duron datasheet, VID. D3 = 1.6 +/- .1, D7 = 1.75 +/- .05 (but do 1.80 +/- 0.05)

    set in0_min 1.75
    set in0_max 1.85

# Duron datasheet, VCCA. D3 = D7 = 2.5 +/- .25

    set in1_min 2.25
    set in1_max 2.75

# Leave 10% for all

    set in2_min 3.3 * 0.9
    set in2_max 3.3 * 1.1

    set in3_min 5.0 * 0.9
    set in3_max 5.0 * 1.1

    set in4_min 12.0 * 0.9
    set in4_max 12.0 * 1.1

# 20 % for negative voltages

    set in5_min -12.0 * 1.2 
    set in5_max -12.0 * 0.8

    set in6_min -5.0 * 1.2
    set in6_max -5.0 * 0.8

    set in7_min 5.0 * 0.9
    set in7_max 5.0 * 1.1

# 20% for battery

set in8_min 3.0 * 0.8
set in8_max 3.0 * 1.2

label temp1 "Sys Temp"
label temp2 "CPU Temp"

set temp1_over 55
set temp1_hyst 52

# Have temp2 (CPU) compliant with the BIOS readout
compute temp2 @-10,@+10

set temp2_over 60
set temp2_hyst 57

# Not connected

    ignore temp3	

    label fan1 "Sys Fan"
    label fan2 "CPU Fan"
    label fan3 "Pow Fan"

    set fan1_div 4 # min RPM = 1.35 x 10^6 / (div * 255) = 1323 (255 == max count)
    set fan2_div 4 # min RPM = 1.35 x 10^6 / (div * 255) = 1323 (255 == max count)
    set fan3_div 4 # min RPM = 1.35 x 10^6 / (div * 255) = 1323 (255 == max count)

    set fan1_min 1500 * 0.9 # 1500 RPM fan
    set fan2_min 2200 * 0.9 # 2200 RPM fan

# set fan3_min nnnn * 0.9 # nnnn RPM fan

# No readout on HD (Pow) fan
ignore fan3

#   0x000001: in0
#   0x000002: in1
#   0x000004: in2
#   0x000008: in3
#   0x000010: temp1
#   0x000020: temp2 (+temp3 on W83781D)
#   0x000040: fan1
#   0x000080: fan2
#   0x000100: in4
#   0x000200: in5
#   0x000400: in6 
#   0x000800: fan3 
#   0x001000: chassis
#   0x002000: temp3 (W83782D and W83627HF only)
#   0x010000: in7 (W83782D and W83627HF only)
#   0x020000: in8 (W83782D and W83627HF only)

set beeps 198655 # 0x0307ff
set beep_enable 1

#2 lore raw

Thanks for your reply.

the sensors.conf I'm currently using is provided by Tyan, so this seems to be ok. One major difference that I can see: I don't have compute statements for the CPU temperatures. If I use your config, I get 7.8°C :-)

So there is definitely some difference in our hardware environment. OTOH with the "right" compute statement the problem seems fixable.

BTW: there is another hwmon chip on the board, a w83627hf. Up to 2.6.21 this was managed by the w83781d driver, too. Now I use the w83627hf driver (on the isa bus). No problem with that part.

-jo

Quoted 32 lines · Rene Herman
Quoted 7 lines · Joerg Sommrey

after upgrading from 2.6.21 to 2.6.22 the CPU temperatures shown by w83781d look unreal. They were in a range from 40°C when idle to 75°C under full load with 2.6.21. The values shown now are in a very small range from 77°C to 82°C. From the (low) noise of the fan I can tell that the temperature is <50°C.
The third temperature shown is completely wrong.

Quoted 5 lines

I have a Tyan Tiger MPX board with a w83782d chip. Output from "sensors":

w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0

As a datapoint, the same W83782D on AMD756 (also I2C) works correctly with 2.6.22:

w83782d-i2c-0-2d
Adapter: SMBus AMD756 adapter at 50e0

Jean Delvare recently worked on the ISA interface to these chips but it seems this would not be the cause if you are also using I2C. Our hardware appears rather identical...

I've attached (an excerpt of) my /etc/sensors.conf -- I once dug through the datasheets for those compute lines for example so perhaps its still useful even if 2.6.21 working for you probably means you don't have a config problem.

Rene.

#3 lore raw
In reply to Joerg Sommrey

Hi Joerg:

(I tried to follow-up using the gmane.org mail/news gateway... didn't seem to work.)

Quoted 24 lines · Joerg Sommrey

Hi,

after upgrading from 2.6.21 to 2.6.22 the CPU temperatures shown by w83781d look unreal. They were in a range from 40°C when idle to 75°C under full load with 2.6.21. The values shown now are in a very small range from 77°C to 82°C. From the (low) noise of the fan I can tell that the temperature is <50°C.
The third temperature shown is completely wrong.

I have a Tyan Tiger MPX board with a w83782d chip. Output from "sensors":

w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0

 +5 V:     +4.81 V  (min =  +4.76 V, max =  +5.24 V)
3 VSB:     +3.30 V  (min =  +2.85 V, max =  +3.15 V)       ALARM
chs3 Fan: 2122 RPM  (min = 2657 RPM, div = 4)              ALARM

VRM2 Temp: -208°C (high = -176°C, hyst = -181°C) sensor = transistor
CPU1 Temp: +78.5°C (high = +80°C, hyst = +75°C) sensor = transistor ALARM
CPU2 Temp: +77.5°C (high = +80°C, hyst = +75°C) sensor = transistor ALARM
alarms:
beep_enable:
Sound alarm enabled

Quoted 6 lines
# cat /sys/bus/i2c/devices/0-002d/temp*_input
-209000
77500
77500

Any ideas?

Please run the following commands as root (against both kernel versions) and reply-to-all with the results:

	# modprobe i2c-dev
	# i2cdump -y 0 0x2d b 0 0x4e
	# i2cdump -y 0 0x48
	# i2cdump -y 0 0x49

Also, can you confirm that you're using the sensors.conf from here:
http://www.tyan.com/support_download_utility.aspx?model=s.s2466

Finally, can you confirm that "sensors -s" is running (without error) some time during system startup, w/ both kernel versions?

Thanks & regards,

Signature · 8 lines
Mark M. Hoffman
[email protected]


_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
#4 lore raw

Hi Mark,

just to eliminate as many impacts as possible, I did:
- reinstall the unmodified sensors.conf from Tyan's support page
- power off before rebooting

A call to "sensors -s" is done without errors in all cases. The module parameters I use currently with both kernels:

options w83781d force_w83782d=0,0x2d force_subclients=0,0x2d,0x48,0x49 options w83627hf force_addr=0x0c00

When I first realized the problem, I didn't use w83627hf yet. Results are the same when w83781d is used as driver for w83627hf. Parameters in that case just from Tyan:

options w83781d force_w83782d=0,0x2d force_subclients=0,0x2d,0x48,0x49 force_w83627hf=0,0x2c force_subclients=0,0x2c,0x4a,0x4b init=0

"My" i2cdump doesn't accept an -y option, maybe a Debianism. Results see below.

TIA
-jo

### 2.6.21 ###############################
Script started on Wed Aug 8 16:53:10 2007

bear:~/hwmon# i2cdump 0 0x2d b 0 0x4e
  WARNING! This program can confuse your I2C bus, cause data loss and worse!
  I will probe file /dev/i2c-0, address 0x2d, mode byte
  You have five seconds to reconsider and press CTRL-C!
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
20: 6c 6b 70 b4 4d 9a ce 3b ff ff f3 80 67 80 67 d8    lkp?M??;..??g?g?
30: c4 c3 b0 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
40: 01 ec 2f 00 00 00 00 54 2d 02 10 44 01 95 00 a3    ??/....T-??D??.?
50: ff ff 00 ff ff ff 00 80 30 00 ff ff 11 0e ff ff    .......?0...??..
60: 6b 6a 70 b3 4d 9b ce 3b ff ff f3 80 67 80 67 d8    kjp?M??;..??g?g?
70: c4 c3 b0 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
a0: 6b 6a 70 b4 4c 9a ce 3b ff ff f5 80 67 80 67 d8    kjp?L??;..??g?g?
b0: c4 c3 b0 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
c0: 01 00 00 00 00 00 00 54 2d 02 10 44 01 95 00 a3    ?......T-??D??.?
d0: ff ff 00 ff ff ff 00 80 30 00 ff ff 11 0e ff ff    .......?0...??..
e0: 6b 6a 6f b1 4d 9a ce 3b ff ff f5 80 67 80 67 d8    kjo?M??;..??g?g?
f0: c4 c3 b0 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
bear:~/hwmon# i2cdump 0 0x48
No size specified (using byte-data access)
  WARNING! This program can confuse your I2C bus, cause data loss and worse!
  I will probe file /dev/i2c-0, address 0x48, mode byte
  You have five seconds to reconsider and press CTRL-C!
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
10: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
20: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
30: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
40: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
50: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
60: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
70: 3b 00 4b 50 3a 00 4b 50 3a 00 4b 50 3b 00 4b 50    ;.KP:.KP:.KP;.KP
80: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
90: 3b 00 4b 50 3a 00 4b 50 3a 00 4b 50 3b 00 4b 50    ;.KP:.KP:.KP;.KP
a0: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
b0: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
c0: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
d0: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
e0: 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50 3b 00 4b 50    ;.KP;.KP;.KP;.KP
f0: 3a 00 4b 50 3a 00 4b 50 3b 00 4b 50 3b 00 4b 50    :.KP:.KP;.KP;.KP
bear:~/hwmon# i2cdump 0  0x49
No size specified (using byte-data access)
  WARNING! This program can confuse your I2C bus, cause data loss and worse!
  I will probe file /dev/i2c-0, address 0x49, mode byte
  You have five seconds to reconsider and press CTRL-C!
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
10: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
20: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
30: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
40: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
50: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
60: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
70: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
80: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
90: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
a0: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
b0: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
c0: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
d0: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
e0: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
f0: 38 00 4b 50 38 00 4b 50 38 00 4b 50 38 00 4b 50    8.KP8.KP8.KP8.KP
bear:~/hwmon# sensors
w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0
AGP V:     +1.74 V  (min =  +3.14 V, max =  +3.46 V)       ALARM  
 +5 V:     +4.81 V  (min =  +4.73 V, max =  +5.24 V)              
DDR V:     +1.23 V  (min =  +2.85 V, max =  +3.47 V)       ALARM  
3 VSB:     +3.30 V  (min =  +2.85 V, max =  +3.15 V)       ALARM  
Bat V:     +0.00 V  (min =  +2.64 V, max =  +3.95 V)       ALARM  
chs1 Fan:    0 RPM  (min = 2700 RPM, div = 2)              ALARM  
chs2 Fan:    0 RPM  (min = 3970 RPM, div = 2)              ALARM  
chs3 Fan:    0 RPM  (min = 10546 RPM, div = 2)              ALARM  
VRM2 Temp:   +56 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           
CPU1 Temp: +57.5 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           
CPU2 Temp: +56.0 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           
alarms:   
beep_enable:
          Sound alarm enabled

w83627hf-isa-0c00

Adapter: ISA adapter
VCore1:    +1.73 V  (min =  +1.66 V, max =  +1.84 V)              
VCore2:    +1.73 V  (min =  +1.66 V, max =  +1.84 V)              
+3.3 V:    +3.33 V  (min =  +3.14 V, max =  +3.47 V)              
 +12 V:   +11.83 V  (min = +13.21 V, max = +10.83 V)       ALARM  
 -12 V:   -12.11 V  (min = -13.18 V, max = -10.80 V)              
CPU1 Fan: 4041 RPM  (min = 4687 RPM, div = 2)              ALARM  
CPU2 Fan: 4192 RPM  (min = 6750 RPM, div = 2)              ALARM  
VRM1 Temp:   +44 C  (high =  -124 C, hyst =   +16 C)   sensor = transistor   ALARM   
AGP Temp:  +50.0 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           
DDR Temp:  +46.0 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           

alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm disabled

bear:~/hwmon# exit
exit

Script done on Wed Aug 8 16:55:02 2007

### 2.6.22 ###############################
Script started on Wed Aug 8 16:41:41 2007

bear:~/hwmon# i2cdump 0 0x2d b 0 0x4e
  WARNING! This program can confuse your I2C bus, cause data loss and worse!
  I will probe file /dev/i2c-0, address 0x2d, mode byte
  You have five seconds to reconsider and press CTRL-C!
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
20: 6c 6b 70 b3 4c 9a ce 3b ff ff ff 80 67 80 67 d9    lkp?L??;...?g?g?
30: c4 c3 b1 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
40: 01 ec 2f 00 00 00 00 54 2d 02 10 44 01 95 00 a3    ??/....T-??D??.?
50: ff ff 00 ff ff ff 00 80 30 60 ff ff 11 02 ff ff    .......?0`..??..
60: 6c 6b 6f b3 4c 9a ce 3b ff ff ff 80 67 80 67 d9    lko?L??;...?g?g?
70: c4 c3 b1 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
a0: 6c 6b 6f b4 4c 9b ce 3b ff ff ff 80 67 80 67 d9    lko?L??;...?g?g?
b0: c4 c3 b1 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
c0: 01 08 00 00 00 00 00 54 2d 02 10 44 01 95 00 a3    ??.....T-??D??.?
d0: ff ff 00 ff ff ff 00 80 30 60 ff ff 11 02 ff ff    .......?0`..??..
e0: 6b 6a 6f b4 4c 9a ce 3b ff ff ff 80 67 80 67 d9    kjo?L??;...?g?g?
f0: c4 c3 b1 d9 b2 41 06 c5 b2 50 4b fa aa 40 00 00    ?????A???PK??@..
bear:~/hwmon# i2cdump 0 0x48
No size specified (using byte-data access)
  WARNING! This program can confuse your I2C bus, cause data loss and worse!
  I will probe file /dev/i2c-0, address 0x48, mode byte
  You have five seconds to reconsider and press CTRL-C!
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
10: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
20: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
30: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
40: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
50: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
60: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
70: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
80: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
90: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
a0: 50 00 4b 50 4f 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPO.KPP.KPP.KP
b0: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
c0: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
d0: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
e0: 50 00 4b 50 50 00 4b 50 4f 00 4b 50 4f 00 4b 50    P.KPP.KPO.KPO.KP
f0: 50 00 4b 50 50 00 4b 50 50 00 4b 50 50 00 4b 50    P.KPP.KPP.KPP.KP
bear:~/hwmon# i2cdump 0 0x49
No size specified (using byte-data access)
  WARNING! This program can confuse your I2C bus, cause data loss and worse!
  I will probe file /dev/i2c-0, address 0x49, mode byte
  You have five seconds to reconsider and press CTRL-C!
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
10: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
20: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
30: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
40: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
50: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
60: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
70: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
80: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
90: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
a0: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
b0: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
c0: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
d0: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
e0: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
f0: 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50 4f 00 4b 50    O.KPO.KPO.KPO.KP
bear:~/hwmon# sensors
w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0
AGP V:     +1.73 V  (min =  +3.14 V, max =  +3.47 V)       ALARM  
 +5 V:     +4.81 V  (min =  +4.76 V, max =  +5.24 V)              
DDR V:     +1.22 V  (min =  +2.85 V, max =  +3.47 V)       ALARM  
3 VSB:     +3.30 V  (min =  +2.85 V, max =  +3.15 V)       ALARM  
Bat V:     +0.00 V  (min =  +2.64 V, max =  +3.95 V)       ALARM  
chs1 Fan:    0 RPM  (min = 2700 RPM, div = 2)              ALARM  
chs2 Fan:    0 RPM  (min = 3970 RPM, div = 2)              ALARM  
chs3 Fan:    0 RPM  (min = 10546 RPM, div = 2)              ALARM  
VRM2 Temp:   +56 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           
CPU1 Temp: +79.5 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor   ALARM   
CPU2 Temp: +79.5 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor   ALARM   
alarms:   
beep_enable:
          Sound alarm enabled

w83627hf-isa-0c00

Adapter: ISA adapter
VCore1:    +1.71 V  (min =  +1.66 V, max =  +1.84 V)              
VCore2:    +1.71 V  (min =  +1.66 V, max =  +1.84 V)              
+3.3 V:    +3.33 V  (min =  +3.14 V, max =  +3.47 V)              
 +12 V:   +11.83 V  (min = +13.21 V, max = +10.83 V)       ALARM  
 -12 V:   -12.20 V  (min = -13.18 V, max = -10.80 V)              
CPU1 Fan: 4041 RPM  (min = 4687 RPM, div = 2)              ALARM  
CPU2 Fan: 4166 RPM  (min = 6750 RPM, div = 2)              ALARM  
VRM1 Temp:   +43 C  (high =  -124 C, hyst =   +16 C)   sensor = transistor   ALARM   
AGP Temp:  +49.5 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           
DDR Temp:  +46.0 C  (high =   +80 C, hyst =   +75 C)   sensor = transistor           

alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm disabled

bear:~/hwmon# exit

Script done on Wed Aug 8 16:43:20 2007

Quoted 45 lines · Mark M. Hoffman

Hi Joerg:

(I tried to follow-up using the gmane.org mail/news gateway... didn't seem to work.)

Quoted 24 lines · Joerg Sommrey

Hi,

after upgrading from 2.6.21 to 2.6.22 the CPU temperatures shown by w83781d look unreal. They were in a range from 40°C when idle to 75°C under full load with 2.6.21. The values shown now are in a very small range from 77°C to 82°C. From the (low) noise of the fan I can tell that the temperature is <50°C.
The third temperature shown is completely wrong.

I have a Tyan Tiger MPX board with a w83782d chip. Output from "sensors":

w83782d-i2c-0-2d
Adapter: SMBus AMD768 adapter at 80e0

 +5 V:     +4.81 V  (min =  +4.76 V, max =  +5.24 V)
3 VSB:     +3.30 V  (min =  +2.85 V, max =  +3.15 V)       ALARM
chs3 Fan: 2122 RPM  (min = 2657 RPM, div = 4)              ALARM

VRM2 Temp: -208°C (high = -176°C, hyst = -181°C) sensor = transistor
CPU1 Temp: +78.5°C (high = +80°C, hyst = +75°C) sensor = transistor ALARM
CPU2 Temp: +77.5°C (high = +80°C, hyst = +75°C) sensor = transistor ALARM
alarms:
beep_enable:
Sound alarm enabled

Quoted 6 lines
# cat /sys/bus/i2c/devices/0-002d/temp*_input
-209000
77500
77500

Any ideas?

Please run the following commands as root (against both kernel versions) and reply-to-all with the results:

	# modprobe i2c-dev
	# i2cdump -y 0 0x2d b 0 0x4e
	# i2cdump -y 0 0x48
	# i2cdump -y 0 0x49
Quoted 12 lines

Also, can you confirm that you're using the sensors.conf from here:
http://www.tyan.com/support_download_utility.aspx?model=s.s2466

Finally, can you confirm that "sensors -s" is running (without error) some time during system startup, w/ both kernel versions?

Thanks & regards,

Signature · 2 lines
Mark M. Hoffman
[email protected]

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

#5 lore raw

Hi Joerg:

Quoted 12 lines · Joerg Sommrey

Hi Mark,

just to eliminate as many impacts as possible, I did:
- reinstall the unmodified sensors.conf from Tyan's support page
- power off before rebooting

A call to "sensors -s" is done without errors in all cases. The module parameters I use currently with both kernels:

options w83781d force_w83782d=0,0x2d force_subclients=0,0x2d,0x48,0x49 options w83627hf force_addr=0x0c00

Quoted 8 lines

When I first realized the problem, I didn't use w83627hf yet. Results are the same when w83781d is used as driver for w83627hf. Parameters in that case just from Tyan:

options w83781d force_w83782d=0,0x2d force_subclients=0,0x2d,0x48,0x49 force_w83627hf=0,0x2c force_subclients=0,0x2c,0x4a,0x4b init=0

"My" i2cdump doesn't accept an -y option, maybe a Debianism. Results see below.

Newer i2cdump skips the 5-second warning when given -y, that's all.

Quoted 3 lines

### 2.6.21 ###############################
Script started on Wed Aug 8 16:53:10 2007

bear:~/hwmon# i2cdump 0 0x2d b 0 0x4e

(snip tons of results)

Thanks for sending all that. I see one bug clearly, and I'm pretty close to seeing the other one. But for tonight, I need sleep.

In the meantime, please try this command as root, against the newer kernel, *after* you've done 'sensors -s':

	# i2cset -f 0 0x2d 0x5d 0x0e b

Wait > 2 seconds for the hardware to update itself, then run 'sensors' again. I'm pretty sure you'll see the correct temps.

Regards,

Signature · 8 lines
Mark M. Hoffman
[email protected]


_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
#6 lore raw

Hi Mark,

Quoted 35 lines · Mark M. Hoffman

Hi Joerg:

Quoted 12 lines · Joerg Sommrey

Hi Mark,

just to eliminate as many impacts as possible, I did:
- reinstall the unmodified sensors.conf from Tyan's support page
- power off before rebooting

A call to "sensors -s" is done without errors in all cases. The module parameters I use currently with both kernels:

options w83781d force_w83782d=0,0x2d force_subclients=0,0x2d,0x48,0x49 options w83627hf force_addr=0x0c00

Quoted 8 lines

When I first realized the problem, I didn't use w83627hf yet. Results are the same when w83781d is used as driver for w83627hf. Parameters in that case just from Tyan:

options w83781d force_w83782d=0,0x2d force_subclients=0,0x2d,0x48,0x49 force_w83627hf=0,0x2c force_subclients=0,0x2c,0x4a,0x4b init=0

"My" i2cdump doesn't accept an -y option, maybe a Debianism. Results see below.

Newer i2cdump skips the 5-second warning when given -y, that's all.

Quoted 3 lines

### 2.6.21 ###############################
Script started on Wed Aug 8 16:53:10 2007

bear:~/hwmon# i2cdump 0 0x2d b 0 0x4e

(snip tons of results)

Thanks for sending all that. I see one bug clearly, and I'm pretty close to seeing the other one. But for tonight, I need sleep.

Quoted 7 lines

In the meantime, please try this command as root, against the newer kernel, *after* you've done 'sensors -s':

	# i2cset -f 0 0x2d 0x5d 0x0e b

Wait > 2 seconds for the hardware to update itself, then run 'sensors' again. I'm pretty sure you'll see the correct temps.

The displayed temperatures changed to 67.5°C / 66.0°C. Still, this seems to be too high. The power supply's fan runs too slow for such CPU temperatures. In older kernels it becomes noisy above 50°C.

Under load the temperatures shown are around 95°C, way too high.

-jo

Signature · 6 lines
-rw-r--r-- 1 jo users 62 2007-08-08 21:06 /home/jo/.signature

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
#7 lore raw

PATCH 1/1 bad temperature values from w83781d in 2.6.22

Hi Joerg:

Quoted 3 lines · Mark M. Hoffman
Quoted 2 lines

Thanks for sending all that. I see one bug clearly, and I'm pretty close to seeing the other one. But for tonight, I need sleep.

There's just one bug after all. The second was a figment of my sleep-deprived imagination.

Quoted 7 lines
Quoted 7 lines

In the meantime, please try this command as root, against the newer kernel, *after* you've done 'sensors -s':

	# i2cset -f 0 0x2d 0x5d 0x0e b

Wait > 2 seconds for the hardware to update itself, then run 'sensors' again. I'm pretty sure you'll see the correct temps.

Quoted 5 lines · Joerg Sommrey

The displayed temperatures changed to 67.5°C / 66.0°C. Still, this seems to be too high. The power supply's fan runs too slow for such CPU temperatures. In older kernels it becomes noisy above 50°C.

Under load the temperatures shown are around 95°C, way too high.

My bad, there's a second i2cset command that would have done it. Please try this patch against v2.6.22.

* * * * *

commit a3333f720da3a173153b00cebc129c48cd3a40af

Author: Mark M. Hoffman <[email protected]>
Date:   Thu Aug 9 08:12:46 2007 -0400

hwmon: fix w83781d temp sensor type setting

Commit 348753379a7704087603dad403603e825422fd9a introduced a regression that caused temp2 and temp3 sensor type settings to be written to temp1 instead. The result is that temp sensor readings could be way off.

drivers/hwmon/w83781d.c +2 -2
index f85b48f..c95909c 100644
@@ -740,9 +740,9 @@ store_sensor(struct device *dev, struct device_attribute *da,
 static SENSOR_DEVICE_ATTR(temp1_type, S_IRUGO | S_IWUSR,
 	show_sensor, store_sensor, 0);
 static SENSOR_DEVICE_ATTR(temp2_type, S_IRUGO | S_IWUSR,
-	show_sensor, store_sensor, 0);
+	show_sensor, store_sensor, 1);
 static SENSOR_DEVICE_ATTR(temp3_type, S_IRUGO | S_IWUSR,
-	show_sensor, store_sensor, 0);
+	show_sensor, store_sensor, 2);
 
 /* I2C devices get this name attribute automatically, but for ISA devices
    we must create it by ourselves. */
Signature · 8 lines
Mark M. Hoffman
[email protected]


_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
#8 lore raw

Hi Mark,

Quoted 9 lines · Mark M. Hoffman

Hi Joerg:

Quoted 3 lines · Mark M. Hoffman
Quoted 2 lines

Thanks for sending all that. I see one bug clearly, and I'm pretty close to seeing the other one. But for tonight, I need sleep.

There's just one bug after all. The second was a figment of my sleep-deprived imagination.

[...]

Quoted 4 lines

My bad, there's a second i2cset command that would have done it. Please try this patch against v2.6.22.

Great, problem fixed. Thanks a lot for your prompt solution!

-jo

Signature · 6 lines
-rw-r--r-- 1 jo users 62 2007-08-09 08:46 /home/jo/.signature

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Acked-by on v1 1/1
#9 lore raw
In reply to Mark M. Hoffman
Quoted 10 lines · Mark M. Hoffman
Author: Mark M. Hoffman <[email protected]>
Date:   Thu Aug 9 08:12:46 2007 -0400

hwmon: fix w83781d temp sensor type setting

Commit 348753379a7704087603dad403603e825422fd9a introduced a regression that caused temp2 and temp3 sensor type settings to be written to temp1 instead. The result is that temp sensor readings could be way off.

Good catch, sorry for messing up. My test chip is a W83781D, it doesn't have thermal sensor type selection, so I couldn't test that.

Quoted 16 lines
drivers/hwmon/w83781d.c +2 -2
index f85b48f..c95909c 100644
@@ -740,9 +740,9 @@ store_sensor(struct device *dev, struct device_attribute *da,
 static SENSOR_DEVICE_ATTR(temp1_type, S_IRUGO | S_IWUSR,
 	show_sensor, store_sensor, 0);
 static SENSOR_DEVICE_ATTR(temp2_type, S_IRUGO | S_IWUSR,
-	show_sensor, store_sensor, 0);
+	show_sensor, store_sensor, 1);
 static SENSOR_DEVICE_ATTR(temp3_type, S_IRUGO | S_IWUSR,
-	show_sensor, store_sensor, 0);
+	show_sensor, store_sensor, 2);
 
 /* I2C devices get this name attribute automatically, but for ISA devices
    we must create it by ourselves. */
Signature · 1 line
Jean Delvare