Skip to contentSkip to conversation

Looking for Help booting Kernel

U-Boot-Users Nick Droogh 2 participants 3 messages Sep 26, 2007 – Sep 27, 2007

lore
Share & tools
lore
#0 lore raw

Hi,

I am trying to boot the latest kernel for a MPC5200B based board from DENX. I built the latest UBoot which seems to run fine on my board.

With the new uboot, my same environment variables, I can still boot my old kernel.

U-Boot 1.3.0-rc2-dirty (Sep 24 2007 - 08:08:49)

CPU: MPC5200 v1.2, Core v1.1 at 462 MHz

       Bus 132 MHz, IPB 132 MHz, PCI 33 MHz
Board: MyBoard MPC5200 Controller
I2C:   343 kHz, ready
DRAM:  128 MB
FLASH: 64 MB
In:    serial
Out:   serial
Err:   serial
Net:   FEC ETHERNET
IDE:   Bus 0: not available

Type "run net_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 0
Using FEC ETHERNET device
TFTP from server 192.168.100.102; our IP address is 192.168.100.11 Filename 'uImage'.
Load address: 0x200000
Loading: #################################################################

         #############################################
done
Bytes transferred = 1612360 (189a48 hex)
## Booting image at 00200000 ...
   Image Name:   Linux-2.6.19.2
   Created:      2007-09-21   8:11:59 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1612296 Bytes =  1.5 MB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
id mach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:setio
MMU:exit
setup_arch: enter
setup_arch: bootmem
arch: exit
Linux version 2.6.19.2 (nick at nick_lnx) (gcc version 4.0.0 (DENX ELDK 4.1

4.0.0)) \
    #5 Fri Sep 21 04:11:50 EDT 2007

Zone PFN ranges:
DMA 0 -> 32768
Normal 32768 -> 32768
early_node_map[1] active PFN ranges

    0:        0 ->    32768
Built 1 zonelists.  Total pages: 32512
Kernel command line: root=/dev/nfs rw 
nfsroot=192.168.100.102:/opt/eldk/ppc_6xx \
    ip=192.168.100.11:192.168.100.102:192.168.100.102:255.255.255.0:\
    MyBoard:eth0:off console=ttyPSC0,115200 panic=1

PID hash table entries: 512 (order: 9, 2048 bytes) I-pipe 1.5-00: pipeline enabled.
Console: colour dummy device 80x25

... and the kernel runs fine. With the latest kernel from Denx, I get the following:

U-Boot 1.3.0-rc2-dirty (Sep 24 2007 - 08:08:49)

CPU: MPC5200 v1.2, Core v1.1 at 462 MHz

       Bus 132 MHz, IPB 132 MHz, PCI 33 MHz
Board: MyBoard  MPC5200 Controller
I2C:   343 kHz, ready
DRAM:  128 MB
FLASH: 64 MB
In:    serial
Out:   serial
Err:   serial
Net:   FEC ETHERNET
IDE:   Bus 0: not available

Type "run net_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 0
=> boot
Using FEC ETHERNET device
TFTP from server 192.168.100.102; our IP address is 192.168.100.11 Filename 'uImage'.
Load address: 0x200000
Loading: #################################################################

         ##################
done
Bytes transferred = 1212323 (127fa3 hex)
## Booting image at 00200000 ...
   Image Name:   Linux-2.6.23-rc6-gea60adb5-dirty
   Created:      2007-09-26   9:53:02 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1212259 Bytes =  1.2 MB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Is there anything special I need to pass to the kernel for setting up the console on the MPC5200B? I had to change ttyS0 to ttyPSC0 for the old console to work. Is there anything I need to enable inside the kernel?

The kernel command line is:

root=/dev/nfs rw nfsroot=192.168.100.102:/opt/eldk/ppc_6xx \
    ip=192.168.100.11:192.168.100.102:192.168.100.102:255.255.255.0:\
    MyBoard:eth0:off console=ttyPSC0,115200 panic=1

Many thanks,

Nick

#1 lore raw
Quoted 4 lines · In message <[email protected]> you wrote:

Is there anything special I need to pass to the kernel for setting up the console on the MPC5200B? I had to change ttyS0 to ttyPSC0 for the old console to work. Is there anything I need to enable inside the kernel?

What are you talking about - is this an arch/ppc or an arch/powerpc configuration? If you use an arch/powerpc configuration, you have to pass a device tree to Linux, too.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The universe is all a spin-off of the Big Bang.
#2 lore raw

[U-Boot-Users] Looking for Help booting Kernel - part 2

Quoted 7 lines · Wolfgang Denk
Quoted 4 lines · In message <[email protected]> you wrote:

Is there anything special I need to pass to the kernel for setting up the console on the MPC5200B? I had to change ttyS0 to ttyPSC0 for the old console to work. Is there anything I need to enable inside the kernel?

Quoted 10 lines

What are you talking about - is this an arch/ppc or an arch/powerpc configuration? If you use an arch/powerpc configuration, you have to pass a device tree to Linux, too.

Best regards,

Wolfgang Denk

Yes this is a arch/powerpc configuration. I got the device tree compiler, copied/configured a .dts file for my board and compiled it to a .dtb file.
I still don't see any output on my console.

Here are the commands from uboot:

Hit any key to stop autoboot: 0
=> tftp 00800000 myboard.dtb
Using FEC ETHERNET device
TFTP from server 192.168.100.102; our IP address is 192.168.100.11 Filename 'myboard.dtb'.
Load address: 0x800000
Loading: #
done
Bytes transferred = 12288 (3000 hex)
=> fdt addr 00800000 3000
=> fdt boardsetup
=> tftp 00200000 uImage
Using FEC ETHERNET device
TFTP from server 192.168.100.102; our IP address is 192.168.100.11 Filename 'uImage'.
Load address: 0x200000
Loading: #################################################################

         ##################

done
Bytes transferred = 1212322 (127fa2 hex)
=> bootm 00200000 - 00800000
## Booting image at 00200000 ...

   Image Name:   Linux-2.6.23-rc6-gea60adb5-dirty
   Created:      2007-09-26  23:21:49 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1212258 Bytes =  1.2 MB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Booting using the fdt at 0x800000
Loading Device Tree to 007fc000, end 007fefff ... OK

I enclosed my .dts file as well

Thanks again,

Nick

-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: myboard.dts
Url: http://lists.denx.de/pipermail/u-boot/attachments/20070927/7a7c959e/attachment.txt