Skip to contentSkip to conversation

dma error on boot with cf card

DISCUSSION Marc Donner 2 participants 4 messages Feb 5, 2008 – Feb 6, 2008

lore
Share & tools
lore
#0 lore raw

hi,

i have a problem using a cf card with an ide adapter. using debian kernel 2.6.18-5

on boot:

Feb  5 17:38:06 kernel: hdd: max request size: 128KiB
Feb  5 17:38:06 kernel: hdd: 2000880 sectors (1024 MB) w/2KiB Cache, 
CHS=1985/16/63, UDMA(33)
Feb  5 17:38:06 kernel:  hdd:<4>hdd: dma_timer_expiry: dma status == 0x41
Feb  5 17:38:06 kernel: hdd: DMA timeout error
Feb  5 17:38:06 kernel: hdd: dma timeout error: status=0x58 { DriveReady 
SeekComplete DataRequest }
Feb  5 17:38:06 kernel: ide: failed opcode was: unknown
Feb  5 17:38:06 kernel: hdd: irq timeout: status=0xd0 { Busy }
Feb  5 17:38:06 kernel: ide: failed opcode was: unknown
Feb  5 17:38:06 kernel: ide1: reset timed-out, status=0xff
Feb  5 17:38:06 kernel: hdd: status timeout: status=0xff { Busy }
Feb  5 17:38:06 kernel: ide: failed opcode was: unknown
Feb  5 17:38:06 kernel: hdd: drive not ready for command
Feb  5 17:38:06 kernel: ide1: reset timed-out, status=0xff
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 0
Feb  5 17:38:06 kernel: Buffer I/O error on device hdd, logical block 0
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 0
Feb  5 17:38:06 kernel: Buffer I/O error on device hdd, logical block 0
Feb  5 17:38:06 kernel:  unable to read partition table
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 2000640
Feb  5 17:38:06 kernel: Buffer I/O error on device hdd, logical block 250080
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 2000640

any ideas?

regards
Marc

#1 lore raw
Quoted 21 lines · Marc Donner

hi,

i have a problem using a cf card with an ide adapter. using debian kernel 2.6.18-5

on boot:

Feb  5 17:38:06 kernel: hdd: max request size: 128KiB
Feb  5 17:38:06 kernel: hdd: 2000880 sectors (1024 MB) w/2KiB Cache, 
CHS=1985/16/63, UDMA(33)
Feb  5 17:38:06 kernel:  hdd:<4>hdd: dma_timer_expiry: dma status == 0x41
Feb  5 17:38:06 kernel: hdd: DMA timeout error
Feb  5 17:38:06 kernel: hdd: dma timeout error: status=0x58 { DriveReady 
SeekComplete DataRequest }
Feb  5 17:38:06 kernel: ide: failed opcode was: unknown
Feb  5 17:38:06 kernel: hdd: irq timeout: status=0xd0 { Busy }
Feb  5 17:38:06 kernel: ide: failed opcode was: unknown
Feb  5 17:38:06 kernel: ide1: reset timed-out, status=0xff
Feb  5 17:38:06 kernel: hdd: status timeout: status=0xff { Busy }
Feb  5 17:38:06 kernel: ide: failed opcode was: unknown
Feb  5 17:38:06 kernel: hdd: drive not ready for command
Feb  5 17:38:06 kernel: ide1: reset timed-out, status=0xff
Quoted 8 lines
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 0
Feb  5 17:38:06 kernel: Buffer I/O error on device hdd, logical block 0
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 0
Feb  5 17:38:06 kernel: Buffer I/O error on device hdd, logical block 0
Feb  5 17:38:06 kernel:  unable to read partition table
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 2000640
Feb  5 17:38:06 kernel: Buffer I/O error on device hdd, logical block 250080
Feb  5 17:38:06 kernel: end_request: I/O error, dev hdd, sector 2000640

Adapter doesn't support DMA, but controller and CF cards do. To fix, tell the system NOT to use dma on that interface.

Most IDE to CF adapters fail to connect the DMA pins correctly since it was a fairly (3 or 4 years ago) revision to the CF spec to support DMA at all.

--
Len Sorensen

#2 lore raw
Quoted 9 lines · you
Quoted 5 lines · Marc Donner

hi,

i have a problem using a cf card with an ide adapter. using debian kernel 2.6.18-5

Adapter doesn't support DMA, but controller and CF cards do. To fix, tell the system NOT to use dma on that interface.

and how do i disable dma? it is the installer image, and no hdparm is availible. and the ide=nodma boot parameter seems not to work.

Marc

#3 lore raw
Quoted 2 lines · Marc Donner

and how do i disable dma? it is the installer image, and no hdparm is availible. and the ide=nodma boot parameter seems not to work.

ide=nodma works for me on 2.6.18. I think on newer kernels you need hda=nodma which is nice since you can control it per device rather than globally.

--
Len Sorensen