sata_mv: enable active LED blink mode for SoC
PATCH 1/1 sata_mv: enable active LED blink mode for SoC
Enabling blink mode makes the SATA active LED more human visible.
--- drivers/ata/sata_mv.c | 10 +++++++++- 1 files changed, 9 insertions(+), 1 deletions(-)
drivers/ata/sata_mv.c +9 -1
@@ -208,6 +208,10 @@ enum {DMA_IRQ = (1 <<0 ),/* shift by port # */ HC_COAL_IRQ = (1 <<4 ),/* IRQ coalescing */ DEV_IRQ = (1 <<8 ),/* shift by port # */ +SOC_LED_CTRL_OFS =0x2c , +SOC_LED_CTRL_BLINK = (1 <<0 ),/* Active LED blink */ +SOC_LED_CTRL_ACT_PRESENCE = (1 <<2 ),/* Multiplex presence with */ +/* the active LED */ /* Shadow block registers */ SHD_BLK_OFS = 0x100,
@@ -2616,7 +2620,11 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,static void mv_soc_enable_leds (struct mv_host_priv *hpriv,void __iomem *mmio) { -return ; +void __iomem *hc_mmio =mv_hc_base (mmio,0 ); +u32 tmp =readl (hc_mmio +SOC_LED_CTRL_OFS ); + +/* enable blinking mode */ +writel (tmp |SOC_LED_CTRL_BLINK , hc_mmio +SOC_LED_CTRL_OFS ); } static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx,
Signature · 1 line
1.5.2.5
drivers/ata/sata_mv.c enum { · line 214
Quoted 2 lines
drivers/ata/sata_mv.c +2
-0+ SOC_LED_CTRL_ACT_PRESENCE = (1 << 2), /* Multiplex presence with */ +/* the active LED */
meanwhile this mode (multiplexing presence with active LED) is not enabled, but I believe some boards may need it. if your board already have this mode then it's probably done by HW by multiplexing the two wires into one LED.
saeed
Hello Saeed,
Quoted 1 line · Saeed Bishara
Enabling blink mode makes the SATA active LED more human visible.
The patch does make the led responsive, but it does *not* restore it to the old behavior.
With the 2.6.25 kernel (and also during early boot of the device) the HDD led flashes with an intensity that reflects the amount of disk activity (possibly the amount of data transferred), very similar to the LAN led.
The flashing was subtle, but very well visible both with low and with high disk activity.
With 2.6.26.3 without this patch there is no flashing visible at all.
With this patch applied to 2.6.26.3 I only get a very slow and steady blinking of the HDD led. A very regular, almost lazy on/off. The flashing is related to disk activity in that the led stays on when there is no activity, but any relationship to the *intensity* of the disk activity is lost.
So, IMO it is an improvement, but it is definitely not a fix for the regression.
Cheers,
FJP
Frans Pop wrote:
..
Quoted 1 line
So, IMO it is an improvement, but it is definitely not a fix for the regression.
..
With a new copy of hdparm, use "hdparm -Q1 /dev/sd?"
Does that fix your "regression" ?
Quoted 6 lines · Mark Lord
Quoted 2 lines · Frans Pop
So, IMO it is an improvement, but it is definitely not a fix for the regression.
With a new copy of hdparm, use "hdparm -Q1
/dev/sd?" Does that fix your "regression" ?
$ sudo hdparm -Q1 /dev/sda
/dev/sda:
setting queue_depth to 1
queue_depth = 1
Yes, that does result in the original behavior of the led. (Using version 8.9 of hdparm.)
Quoted 8 lines · Frans Pop
Quoted 6 lines · Mark Lord
Quoted 2 lines · Frans Pop
So, IMO it is an improvement, but it is definitely not a fix for the regression.
With a new copy of hdparm, use "hdparm -Q1
/dev/sd?" Does that fix your "regression" ?
Quoted 8 lines
$ sudo hdparm -Q1 /dev/sda
/dev/sda:
settingqueue_depthto 1
queue_depth= 1Yes, that does result in the original behavior of the led. (Using version 8.9 of hdparm.)
But that's not new information: we'd already determined some time ago that disabling NCQ "fixed" the problem, both if it is done at runtime and when it is disabled in the driver:
http://www.spinics.net/lists/linux-ide/msg25642.html
http://www.spinics.net/lists/linux-ide/msg25645.html
Quoted 13 lines · Frans Pop
Quoted 12 lines · Frans Pop
Quoted 5 lines · Mark Lord
Quoted 2 lines · Frans Pop
So, IMO it is an improvement, but it is definitely not a fix for the regression.
With a new copy of hdparm, use "hdparm -Q1
/dev/sd?" Does that fix your "regression" ?$ sudo hdparm -Q1 /dev/sda
/dev/sda:
settingqueue_depthto 1
queue_depth= 1
Quoted 8 lines
Quoted 2 lines
Yes, that does result in the original behavior of the led. (Using version 8.9 of hdparm.)
But that's not new information: we'd already determined some time ago that disabling NCQ "fixed" the problem, both if it is done at runtime and when it is disabled in the driver:
http://www.spinics.net/lists/linux-ide/msg25642.html
http://www.spinics.net/lists/linux-ide/msg25645.html
Setting queue_depth to 1 is not disabling NCQ; it's NCQ enabled, no more than one command outstanding at a time. A queue depth of 0 disables NCQ completely.
While I don't have the relevant hardware, this sounds like a hardware limitation, not a regression. I suspect that the LED is active whenever a command is outstanding; with NCQ allowed to queue more than 1 command at a time, Linux is keeping the drive fed with commands so that there are always outstanding commands, and thus the light never goes inactive during disk activity.
As a result, you never see the LED intensity vary, as the drive never idles waiting for a new command, but is constantly processing commands as fast as it can. Allowing the drive to idle would get you the "flickering" you want, at the expense of the performance gain NCQ provides.
Signature · 3 lines
I'm sure Saeed or Mark will correct me if I'm completely wrong, Simon Farnsworth
Quoted 3 lines
While I don't have the relevant hardware, this sounds like a hardware limitation, not a regression. I suspect that the LED is active
whenever
Quoted 1 line
a command is outstanding; with NCQ allowed to queue more than 1
command
Quoted 2 lines
at a time, Linux is keeping the drive fed with commands so that there are always outstanding commands, and thus the light never goes
inactive
Quoted 7 lines
during disk activity.
As a result, you never see the LED intensity vary, as the drive never idles waiting for a new command, but is constantly processing commands as fast as it can. Allowing the drive to idle would get you the "flickering" you want, at the expense of the performance gain NCQ provides.
Frans reported that the LED stays on during disk activity, so it looks like the drive always unbusy. I need to check with the HW guys how the activity LED behaves in NCQ mode. I suspect that this disk responds immediately to new commands telling the host "I got the command and it will be handled later", this response clears the ports ATA busy bit. If the activity LED reflects only the state of that bit in NCQ mode, then that could explain the behavior that Frans described.
- saeed
Quoted 4 lines · Simon Farnsworth
..
Settingqueue_depthto 1 is not disabling NCQ; it's NCQ enabled, no more than one command outstanding at a time. A queue depth of 0 disables NCQ completely.
..
Unfortunately, in the libata implementation, a queue depth of 1 actually *does* disable NCQ. I wish it didn't (for easier testing of features), but it does.
Cheers
Quoted 13 lines · Frans Pop
Quoted 12 lines · Frans Pop
Quoted 5 lines · Mark Lord
Quoted 2 lines · Frans Pop
So, IMO it is an improvement, but it is definitely not a fix for the regression.
With a new copy of hdparm, use "hdparm -Q1
/dev/sd?" Does that fix your "regression" ?$ sudo hdparm -Q1 /dev/sda
/dev/sda:
settingqueue_depthto 1
queue_depth= 1
Quoted 6 lines
Quoted 2 lines
Yes, that does result in the original behavior of the led. (Using version 8.9 of hdparm.)
But that's not new information: we'd already determined some time ago that disabling NCQ "fixed" the problem, both if it is done at runtime and when it is disabled in the driver:
http://www.spinics.net/lists/linux-ide/msg25642.html
http://www.spinics.net/lists/linux-ide/msg25645.html
..
Still, that's proof that there is NO REGRESSION here, so please stop using that term.
Older kernels had a working LED without NCQ,
and so do newer ones. No regression.
In the meanwhile, it appears that Saeed is working to determine for sure that this is a hardware limitation, as it appears to be.
Cheers